Filename: tfs 167f.doc Version 2.0 VI TELEFILTER 29.10.2004 Filter specification TFS 167F 1/5 Measurement condition Ambient temperature: 23 C Input power level: 0 dBm Terminating impedances at fc *: input: output: 869 1058 -8,5 pF -5,9 pF Characteristics Remark: Reference level for the relative attenuation arel of the TFS 167F is the minimum of the pass band attenuation amin. The maximum of the pass band attenuation is defined as the insertion loss a e. The centre frequency fc is the arithmetic mean value of the upper and lower frequencies at the 2 dB filter attenuation level relative to the insertion loss ae. The nominal frequency fN is fixed at 167 MHz without tolerance. The given values for the relative attenuation arel and for the group delay ripple have to be reached at the frequencies given below even if the centre frequency fc is shifted due to the temperature coefficient of frequency TCf in the operating temperature range and due to a production tolerance for the centre frequency fc. Data Insertion loss typ. Value ae 5,8 Nominal frequency fN - Passband PB - Limit dB max. fN ± 7 dB 167 MHz 75 kHz Amplitude variation in PB p-p 0,7 dB max. 1,5 dB Amplitude ripple in PB p-p 0,05 dB max. 1 dB Relative Attenuation fN ± 0,2 MHz ... fN ± 0,4 fN ± 0,4 MHz ... fN ± 0,6 fN ± 0,6 MHz ... fN ± 0,8 fN ± 0,8 MHz ... fN ± 1,6 fN ± 1,6 MHz ... fN ± 20 fN - 137 MHz ... fN - 20 fN + 20 MHz ... fN + 103 fN +103 MHz ... fN + 105 fN +105 MHz ... fN + 1 arel min. min. min. min. min. min. min. min. min. 2 17 36 41 41 67 67 60 67 dB dB dB dB dB dB dB dB dB ns max. 400 ns µs max. MHz MHz MHz MHz MHz MHz MHz MHz GHz Group delay variation in PB Group delay in PB 3,5 25 43 45 47 73 73 67 75 200 2,4 dB dB dB dB dB dB dB dB dB 2,6 µs Input return loss in PB 20 dB min. 15 dB Output return loss in PB 18 dB min. 10 dB max. 22 dBm**) Input Power Level - Temperature coefficient of frequency Tc f - 0,036 ppm/K Frequency inversion temperature T 0 35 2 - °C - Operating temperature range - - 5 °C .. + 85 °C Storage temperature range - - 40 °C.. + 90 °C min. 100 dB Intermodulation ratio 120 dB input signals at 167 + 0,8 MHz and 167 + 1,6 MHz or at 167 - 0,8 MHz and 167 - 1,6 MHz, each at -20 dBm *) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values only. Should there be additional questions do not hesitate to ask for an application note or contact our design team. **) This power level is only allowed for short term operation (1% of the life time), the max. input power for continuous operation is max.15dBm only generated: checked / approved: Tele Filter GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 167f.doc Version 2.0 VI TELEFILTER 29.10.2004 Filter specification TFS 167F 2/5 Filter characteristic B d ni e d ut i n g a m 0 0 4.89 -10 -1 4.59 -20 -2 4.29 -30 -3 3.99 -4 B d ni e d ut i n g a m -40 -7 3.69 sµ 3.39ni y a 3.09el d 2.79 -80 -8 2.49 -90 -9 2.19 -50 -60 -70 -100 165 165.4 165.8 166.2 166.6 167 167.4 167.8 168.2 168.6 frequency in MHz 169 -5 -6 -10 1.89 166.75 166.8 166.85 166.9 166.95 167 167.05 167.1 167.15 167.2 167.25 frequency in MHz Construction and Pin Connection (All dimensions in mm) 10 6 TFS 167F S44 2 1 data code: S T U ...... +0,20 19 - 0,10 year + week 2004 2005 2006 date code 5 pin 1 pin 2 pin 3 pin 4 pin 5 pin 6 pin 7 pin 8 pin 9 pin 10 1,02 1 input (rf return) ground ground ground output (rf return) output ground ground ground input 1,91 7,62 matching circuit for example: input 50 single ended / output 200 L1 differential 6 10 LB-OUT 200 Ohm : 50 Ohm L2 Output Input S AW C1 1 C2 5 L3 2,3,4,7,8,9 other options possible: - 200 differential in / out - 50 single ended in / out Tele Filter GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 167f.doc Version 2.0 VI TELEFILTER 29.10.2004 Filter specification TFS 167F 3/5 Stability characteristics After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 18 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0,35 mm or g respectively, 1 octave per min, 10 cycles per plan, 3 plans; DIN IEC 68 T2 - 6 3. Change of temperature: 4. Resistance to solder heat (reflow): 5. ESD -55 °C to 125°C / 30 min. each / 10 cycles DIN IEC 68 part 2 14 Test N reflow possible: twice max.; for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4; MIL-STD-883E using coupling network of ISO 10605 and EN 6100-4-2 HBM:500V; MM:500V; Packing Tape & Reel: IEC 286 3, with exeption of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters peer reel: reel of empty components at start: reel of empty components at start including leader: trailer: Tape (all dimensions in mm) W : 32,00 ± 0,3 Po : 4,00 ± 0,1 Do : 1,50 +0,1/-0 E : 1,75 ± 0,1 F : 14,20 ± 0,1 P2 : 2,00 ± 0,1 P1 : 12,00 ± 0,1 D1(min) : 2,00 Ao : 7,10 ± 0,1 Bo : 19,60 ± 0,1 So : 28,40 ± 0,1 Ct : 25,5 ± 0,1 Ko : 2,5 ± 0,1 t : 0,35 ± 0,35 2000 min. 300 mm min. 500 mm min. 300 mm Pull Off Direction t Do Po P1 P2 Date Code Ao Ko Type PIN Marker D1 W2 Reel (all dimensions in mm) A : 330 W1 : 34 W2(max) : 38 N(min) : 100 C : 13 C A N W1 The minimum bending radius is 45 mm. Tele Filter GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. VI TELEFILTER Filter specification Air reflow temperature conditions Conditions Exposure Chip-mount air reflow profile Tele Filter GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] TFS 167F 4/5 Filename: tfs 167f.doc VI TELEFILTER Version 2.0 Filter specification 29.10.2004 TFS 167F 5/5 History Version Reason of Changes Name Date 1.0 generation of Development specification according to customer requirements Pfeiffer 24.04.2003 1.1 return loss limits specified Pfeiffer 30.04.2003 1.2 terminating impedance fixed Pfeiffer typical values and matching configuration added frequency range for 50 dB stopband limit changed to fN +103 MHz ... fN + 105 MHz 07.08.2003 1.3 limit of relative attenuation in fN +103 MHz ... fN + 105 MHz changed to 60dB Pfeiffer 17.10.2003 1.4 type error within relative attenuation for pass band corrected Steiner 12.11.2003 1.5 delete relative attenuation in pass band Wall 18.11.2003 1.6 tape and reel dimensions corrected filter characteristic added Pfeiffer 19.05.2004 1.7 relaxation in ultimate rejection Noack 15.07.2004 1.8 ESD limits added Pfeiffer 19.08.2004 1.9 conditions for input power level modified Pfeiffer 10.09.2004 2.0 air reflow temperature conditions modified Pfeiffer 29.10.2004 Tele Filter GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.