VECTRON TFS457

Filename: tfs 457.doc
Version 1.3
VI TELEFILTER
03.05.2004
Filter specification
TFS 457
1/5
Measurement condition
Ambient temperature:
Input power level:
Terminating impedance: *
Input:
Output:
23
0
°C
dBm
165 Ω || -0,3 pF
165 Ω || -0,3 pF
Characteristics
Remark:
Reference level for the relative attenuation arel of the TFS 457 is the minimum of the pass band attenuation amin. The minimum of the pass band
attenuation amin is defined as the insertion loss ae. The centre frequency fC is the arithmetic mean value of the upper and lower frequencies at the 2dB
filter attenuation level relative to the insertion loss ae. The nominal frequency fN is fixed on 457,5 MHz without tolerance. The given values for the relative
attenuation arel and for the group delay ripple have to be reached at the frequencies given below also if the centre frequency fC is shifted due to the
temperature coefficient of frequency TCf in the operating temperature range and due to a production tolerance for the centre frequency fC.
Data
typ. value
ae = amin
Insertion loss
(reference level)
2,7
-
Nominal frequency
fN
-
Centre frequency
fC
457,5
Passband
-
Pass band ripple
1,2 **
MHz
MHz
MHz
MHz
MHz
max.
3,0
457,5
MHz
dB
MHz
fN ± 12
MHz
dB
max.
3,0** dB
dB
dB
dB
dB
dB
min.
min.
min.
min.
min.
min.
50
30
20
40
57
20,0
dB
dB
dB
dB
dB
dBm
arel
Relative attenuation
fN 80,0
35,0
fN 25,0
fN +
57,5
fN +
127,5
fN +
Intermodulation
dB
tolerance / limit
…
…
…
…
…
fN
fN
fN
fN
fN
+
+
+
100,0
55,0
57,5
82,5
152,5
MHz
MHz
MHz
MHz
MHz
IP3 ***
62
50
24
55
68
-
Input power level
-
max.
10
dBm
Permissible DC voltage
-
max.
12
V
Operating temperature range
OTR
Storage temperature range
Temperature coefficient of frequency
TCf ****
-
- 25 °C ... + 75°C
-
- 40 °C ... + 85°C
- 72
ppm/K
*) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference
values only. Should there be additional questions do not hesitate to ask for an application note or contact our design team.
**) 1,5 dB over fN ± 10 MHz at ambiente temperature (23 °C).
***) modulation signals:
fN + 1 MHz and fN + 2 MHz, each of 10 dBm
****) ∆f(Hz) = TCf(ppm/K) x (T-T0) x fTo(MHz).
Generated:
Checked / Approved:
Tele Filter GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is
assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.
Filename: tfs 457.doc
Version 1.3
VI TELEFILTER
03.05.2004
Filter specification
TFS 457
2/5
Filter characteristic
0
0
-10
-1
-2
-20
-3
Return Loss [dB]
Return Loss [dB]
-30
-40
-50
-60
-5
-6
-7
-70
-8
-80
-90
-4
-9
350
400
450
500
frequency [MHz]
550
-10
435
600
440
445
450
455
460
frequency [MHz]
465
470
475
Construction and pin connection
(All dimensions in mm)
S 457
● S19
1
2
3
4
5
6
7
8
Input
Ground
Ground
Ground
Output
Ground
Ground
Ground
Date code:
S
T
U
...
Year + week
2004
2005
2006
50 Ω Test circuit
1
5
L2
C2
2, 3, 4, 6, 7, 8
Tele Filter GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is
assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.
Filename: tfs 457.doc
Version 1.3
VI TELEFILTER
03.05.2004
Filter specification
TFS 457
3/5
Stability characteristics
After the following tests the filter shall meet the whole specification:
1. Shock:
500g, 18 ms, half sine wave, 3 shocks each plane;
DIN IEC 68 T2 - 27
2. Vibration:
10 Hz to 500 Hz, 0,35 mm or 5 g respectively, 1 octave per min, 10 cycles per plan, 3 plans;
DIN IEC 68 T2 - 6
3. Change of
temperature:
4. Resistance to
solder heat (reflow):
-55 °C to 125°C / 30 min. each / 10 cycles
DIN IEC 68 part 2 – 14 Test N
reflow possible: twice max.;
for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4;
Packing
Tape & Reel:
IEC 286 – 3, with exeption of value for N and minimum bending radius;
tape type II, embossed carrier tape with top cover tape on the upper side;
max. pieces of filters peer reel:
reel of empty components at start:
reel of empty components at start including leader:
trailer:
3000
min. 300 mm
min. 500 mm
min. 300 mm
EMBOSSED CARRIER TAPE
Tape (all dimensions in mm)
W
: 12,00 ± 0,3
Po
: 4,00 ± 0,1
Do
: 1,50 +0,1/-0
E
: 1,75 ± 0,1
F
: 5,50 ± 0,05
G(min)
: 0,75
P2
: 2,00 ± 0,05
P1
: 8,00 ± 0,1
D1(min)
: 1,50
Ao
: 5,30 ± 0,1
Bo
: 5,30 ± 0,1
Ct
: 9,5 ± 0,1
Do
Po
P2
E
Ao
F
D1
Ct
W
Bo
G
P1
COVER TAPE
W 2
Reel (all dimensions in mm)
A
: 330
W1
: 12,4 +2/-0
W2(max) : 18,4
N(min)
: 50
C
: 13,0 +0,5/-0,2
A
C
N
W 1
The minimum bending radius is 45 mm. The mounting surface of the filters faces the bottom side of the embossed carrier tape. Marking
of the filters can be read if the upper side of the carrier tape is regarded with the sprocket holes on the right.
Tele Filter GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is
assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.
Filename: tfs 457.doc
Version 1.3
VI TELEFILTER
03.05.2004
Filter specification
TFS 457
4/5
Air reflow temperature conditions
1st and 2nd air reflow profile
Name:
Temperature:
Time:
pre-heating periods main-heating periods
150 °C - 170 °C
over 200 °C
60 sec. - 90 sec.
20 sec. - 25 sec.
peak temperature
255 °C ± 5 °C
Chip-mount air reflow profile
260
240
220
200
temperature / °C
180
160
140
120
100
80
60
40
20
0
0
20
40
60
80
100
120
140
160
180
200
220
240
time / sec.
Table for temperature vs. time during the air reflow process
Tolerance of temperatures: ± 5 °C
time / sec.
0
10
20
30
40
50
60
70
80
90
100
110
120
130
temperature / °C
23
34
46
60
80
103
121
134
143
150
154
156
158
159
time / sec.
140
150
160
170
180
190
195
200
205
210
215
220
230
240
temperature / °C
160
161
164
170
180
205
230
255
230
205
180
165
140
120
Air reflow temperature conditions
1st and 2nd air reflow profile
Name:
Temperature:
Time:
pre-heating periods main-heating periods
150 °C - 170 °C
over 200 °C
110 sec. - 140 sec. 60 sec. - 65 sec.
peak temperature
230 °C ± 5 °C
Tele Filter GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is
assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.
Filename: tfs 457.doc
VI TELEFILTER
Version 1.3
Filter specification
03.05.2004
TFS 457
5/5
Version
Reason of Changes
Name
Date
1.0
- generate according customer requirement specification
Dr. Sabah
11.07.2001
1.1
- add of 50 Ω matching circuit
Dr. Sabah
13.07.2001
1.2
- correct the matching circuit
Dr. Sabah
17.08.2001
Noack
03.05.2004
1.2
-
generation of filter specification
add typical value
add input and output impedance
add filter characteristic
Tele Filter GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is
assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.