MITSUBISHI MITSUBISHI SEMICONDUCTOR SEMICONDUCTOR <Dual-In-Line <Dual-In-Line Package Package Intelligent Intelligent Power Power Module> Module> PS21964/-A/-C PS21964/-A/-C TRANSFER-MOLD TRANSFER-MOLD TYPE TYPE INSULATED INSULATED TYPE TYPE PS21964-A INTEGRATED POWER FUNCTIONS 600V/15A low-loss 5th generation IGBT inverter bridge for three phase DC-to-AC power conversion INTEGRATED DRIVE, PROTECTION AND SYSTEM CONTROL FUNCTIONS • • • • For upper-leg IGBTS : Drive circuit, High voltage isolated high-speed level shifting, Control supply under-voltage (UV) protection. For lower-leg IGBTS : Drive circuit, Control supply under-voltage protection (UV), Short circuit protection (SC). Fault signaling : Corresponding to an SC fault (Lower-leg IGBT) or a UV fault (Lower-side supply). Input interface : 3V, 5V line (High Active). APPLICATION AC100V~200V three-phase inverter drive for small power motor control. Fig. 1 PACKAGE OUTLINES (PS21964) Dimensions in mm Type name Code Lot No. 0.4 14.4 ±0.5 12 QR 24 ±0.5 .6 R1 2- 18 (3.3) 29.2 ±0.5 14.4 ±0.5 (1) 1 TERMINAL CODE 1.5 ±0.05 0.5 17 3.5 B A (3.5) 38 ±0.5 35 ±0.3 0.28 1.778 ±0.2 0.8 HEAT SINK SIDE 3.08 0.4 25 0.28 2.54 ±0.2 0.6 4-C1.2 14×2.54 (=35.56) (0.678) 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. (VNC) VUFB VVFB VWFB UP VP WP VP1 VNC UN VN WN VN1 FO CIN VNC VNO NC NC N W V U P NC (0.678) 0.5 0.5 0.5 1.5m in (0~5°) (1.2) HEAT SINK SIDE 5.5 ±0.5 9.5 ±0.5 0.5 (1.2) DETAIL A DETAIL B Jun. 2005 MITSUBISHI SEMICONDUCTOR <Dual-In-Line Package Intelligent Power Module> PS21964/-A/-C TRANSFER-MOLD TYPE INSULATED TYPE Fig. 2 LONG TERMINAL TYPE PACKAGE OUTLINES (PS21964-A) B A 1.5 ±0.05 (1) 1 Lot No. 0.8 14.4 Code 29.4 ±0.5 Type name ±0.5 12 QR 24 ±0.5 .6 R1 2- (3.5) 14.4 ±0.5 17 18 TERMINAL CODE 3.5 0.4 0.5 (3.3) 38 ±0.5 35 ±0.3 0.28 1.778 ±0.2 Dimensions in mm HEAT SINK SIDE 3.08 0.4 25 0.6 4-C1.2 14×2.54(=35.56) 0.5 (0.678) 0.5 (0.678) 0.5 5.5 ±0.5 (1.2) 14 ±0.5 0.5 (VNC) VUFB VVFB VWFB UP VP WP VP1 VNC UN VN WN VN1 FO CIN VNC VNO NC NC N W V U P NC HEAT SINK SIDE 1.5m in (0~5°) 0.28 2.54 ±0.2 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. (1.2) DETAIL A DETAIL B Dimensions in mm Fig. 3 ZIGZAG TERMINAL TYPE PACKAGE OUTLINES (PS21964-C) 38 ±0.5 35 ±0.3 Type name Code Lot No. 0.4 TERMINAL CODE 18 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 14.4 (3.5) ±0.5 18.9 ±0.5 14.4 ±0.5 12 QR 33.7 ±0.5 1 24 ±0.5 17 1.5 ±0.05 (1) A .6 R1 2- 3.5 B 29.2 ±0.5 0.28 1.778 ±0.2 0.8 3.08 0.4 25 0.28 2.54 ±0.2 0.6 (0.678) 4-C1.2 14×2.54 (=35.56) (0~5°) (0.678) 0.5 (1.2) 5.5 ±0.5 HEAT SINK SIDE 1.5m in (0~5°) 0.5 9.5 ±0.5 0.5 (VNC) VUFB VVFB VWFB UP VP WP VP1 VNC UN VN WN VN1 FO CIN VNC VNO NC NC N W V U P NC (1.2) DETAIL A DETAIL B Jun. 2005 MITSUBISHI SEMICONDUCTOR <Dual-In-Line Package Intelligent Power Module> PS21964/-A/-C TRANSFER-MOLD TYPE INSULATED TYPE Fig. 4 INTERNAL FUNCTIONS BLOCK DIAGRAM (TYPICAL APPLICATION EXAMPLE) Input signal conditioning Level shifter Level shifter Level shifter Drive circuit Drive circuit CBW+ Input signal conditioning CBW– CBV+ Input signal conditioning CBV– CBU+ CBU– High-side input (PWM) (3V, 5V line)(Note 1, 2) C1 : Tight tolerance, temp-compensated electrolytic type (Note : The capacitance value depends on the PWM control scheme used in the applied system). C2 : 0.22~2µF R-category ceramic capacitor for noise filtering. C2 C1 (Note 7) (Note 5) Protection circuit (UV) Inrush current limiter circuit Drive circuit P H-side IGBTS DIP-IPM AC line input U V W (Note 4) M (Note 8) C Z N1 N L-side IGBTS VNO (Note 6) VNC AC line output CIN Z : ZNR (Surge absorber) C : AC filter (Ceramic capacitor 2.2~6.5nF) (Note : Additionally, an appropriate line-to line surge absorber circuit may become necessary depending on the application environment). Drive circuit Input signal conditioning Protection Control supply circuit Under-Voltage Fo logic protection (Note 7) Low-side input (PWM) FO (3V, 5V line)(Note 1, 2) Fault output (5V line) (Note 3) Note1: 2: 3: 4: 5: 6: 7: 8: VNC (15V line) VD Input logic is high-active. There is a 3.3kΩ (min) pull-down resistor built-in each input circuit. When using an external CR filter, please make it satisfy the input threshold voltage. By virtue of integrating an application specific type HVIC inside the module, direct coupling to MCU terminals without any opto-coupler or transformer isolation is possible. (see also Fig. 10) This output is open drain type. The signal line should be pulled up to the positive side of the 5V power supply with approximately 10kΩ resistor. (see also Fig. 10) The wiring between the power DC link capacitor and the P & N1 terminals should be as short as possible to protect the DIP-IPM against catastrophic high surge voltages. For extra precaution, a small film type snubber capacitor (0.1~0.22µF, high voltage type) is recommended to be mounted close to these P & N1 DC power input pins. High voltage (600V or more) and fast recovery type (less than 100ns) diodes should be used in the bootstrap circuit. The terminal VNO should be connected with the terminal VNC outside. It is recommended to insert a Zener diode (24V/1W) between each pair of control supply terminals to prevent surge destruction. Bootstrap negative electrodes should be connected to U, V, W terminals directly and separated from the main output wires. Fig. 5 EXTERNAL PART OF THE DIP-IPM PROTECTION CIRCUIT DIP-IPM Short Circuit Protective Function (SC) : SC protection is achieved by sensing the L-side DC-Bus current (through the external shunt resistor) after allowing a suitable filtering time (defined by the RC circuit). When the sensed shunt voltage exceeds the SC trip-level, all the L-side IGBTs are turned OFF and a fault signal (Fo) is output. Since the SC fault may be repetitive, it is recommended to stop the system when the Fo signal is received and check the fault. Drive circuit P IC (A) H-side IGBTS SC Protection Trip Level U V W L-side IGBTS External protection circuit N1 Shunt Resistor A N (Note 1) VNC C R Drive circuit CIN B C Collector current waveform Protection circuit (Note 2) Note1: In the recommended external protection circuit, please select the RC time constant in the range 1.5~2.0µs. 2: To prevent erroneous protection operation, the wiring of A, B, C should be as short as possible. 0 2 tw (µs) Jun. 2005 MITSUBISHI SEMICONDUCTOR <Dual-In-Line Package Intelligent Power Module> PS21964/-A/-C TRANSFER-MOLD TYPE INSULATED TYPE MAXIMUM RATINGS (Tj = 25°C, unless otherwise noted) INVERTER PART Symbol VCC VCC(surge) VCES ±IC ±ICP PC Tj Parameter Condition Applied between P-N Supply voltage Supply voltage (surge) Collector-emitter voltage Each IGBT collector current Each IGBT collector current (peak) Collector dissipation Junction temperature Ratings Applied between P-N TC = 25°C TC = 25°C, less than 1ms TC = 25°C, per 1 chip (Note 1) 450 500 600 15 30 33.3 –20~+125 Unit V V V A A W °C Note 1 : The maximum junction temperature rating of the power chips integrated within the DIP-IPM is 150°C (@ TC ≤ 100°C). However, to ensure safe operation of the DIP-IPM, the average junction temperature should be limited to Tj(ave) ≤ 125°C (@ TC ≤ 100°C). CONTROL (PROTECTION) PART Symbol Parameter VD VDB Control supply voltage Control supply voltage VIN Input voltage VFO IFO VSC Fault output supply voltage Fault output current Current sensing input voltage Condition Ratings Unit Applied between VP1-VNC, VN1-VNC Applied between VUFB-U, VVFB-V, VWFB-W Applied between UP, VP, WP, UN, VN, WN-VNC Applied between FO-VNC 20 20 V V –0.5~VD+0.5 V –0.5~VD+0.5 1 –0.5~VD+0.5 V mA V Ratings Unit 400 V –20~+100 –40~+125 °C 1500 Vrms Sink current at FO terminal Applied between CIN-VNC TOTAL SYSTEM Symbol Condition VD = 13.5~16.5V, Inverter part Tj = 125°C, non-repetitive, less than 2µs (Note 2) Parameter VCC(PROT) Self protection supply voltage limit (short circuit protection capability) Module case operation temperature TC Tstg Storage temperature Viso 60Hz, Sinusoidal, AC 1 minutes, All connected pins to heat-sink plate Isolation voltage °C Note 2: TC measurement point Control terminals 11.6mm DIP-IPM 3mm IGBT chip position TC point FWD chip position Heat sink side Power terminals Jun. 2005 MITSUBISHI SEMICONDUCTOR <Dual-In-Line Package Intelligent Power Module> PS21964/-A/-C TRANSFER-MOLD TYPE INSULATED TYPE THERMAL RESISTANCE Symbol Rth(j-c)Q Rth(j-c)F Condition Parameter Junction to case thermal resistance (Note 3) Inverter IGBT part (per 1/6 module) Inverter FWD part (per 1/6 module) Min. — — Limits Typ. — — Max. 3.0 3.9 Unit °C/W °C/W Note 3 : Grease with good thermal conductivity should be applied evenly with about +100µm~+200µm on the contacting surface of DIP-IPM and heat-sink. The contacting thermal resistance between DIP-IPM case and heat sink (Rth(c-f)) is determined by the thickness and the thermal conductivity of the applied grease. For reference, Rth(c-f) (per 1/6 module) is about 0.3°C/W when the grease thickness is 20µm and the thermal conductivity is 1.0W/m·k. ELECTRICAL CHARACTERISTICS (Tj = 25°C, unless otherwise noted) INVERTER PART Symbol VCE(sat) VEC ton trr tc(on) toff tc(off) ICES Condition Parameter Collector-emitter saturation voltage FWD forward voltage Switching times IC = 15A, Tj = 25°C VD = VDB = 15V VIN = 5V IC = 15A, Tj = 125°C Tj = 25°C, –IC = 15A, VIN = 0V VCC = 300V, VD = VDB = 15V IC = 15A, Tj = 125°C, VIN = 0 ↔ 5V Inductive load (upper-lower arm) Collector-emitter cut-off current VCE = VCES Tj = 25°C Tj = 125°C Min. — — — Limits Typ. 0.70 — — — — — — 1.70 1.80 1.70 1.30 0.30 0.50 1.60 0.50 — — Max. 2.20 2.30 2.20 1.90 — 0.75 2.20 0.80 1 10 Min. — — — — 4.9 — 0.43 0.70 10.0 10.5 10.3 10.8 20 — 0.8 Limits Typ. — — — — — — 0.48 1.00 — — — — — 2.1 1.3 Max. 2.80 0.55 2.80 0.55 — 0.95 0.53 1.50 12.0 12.5 12.5 13.0 — 2.6 — 0.35 0.65 — Unit V V µs µs µs µs µs mA CONTROL (PROTECTION) PART Symbol ID VFOH VFOL VSC(ref) IIN UVDBt UVDBr UVDt UVDr tFO Vth(on) Vth(off) Vth(hys) Parameter Circuit current FO output voltage Short circuit trip level Input current Control supply under-voltage protection Fault output pulse width ON threshold voltage OFF threshold voltage ON/OFF threshold hysteresis voltage Condition VD = VDB = 15V Total of VP1-VNC, VN1-VNC VIN = 5V VUFB-U, VVFB-V, VWFB-W Total of VP1-VNC, VN1-VNC VD = VDB = 15V VIN = 0V VUFB-U, VVFB-V, VWFB-W VSC = 0V, FO terminal pull-up to 5V by 10kΩ VSC = 1V, IFO = 1mA Tj = 25°C, VD = 15V (Note 4) VIN = 5V Trip level Reset level Tj ≤ 125°C Trip level Reset level (Note 5) Applied between UP, VP, WP, UN, VN, WN-VNC Unit mA mA mA mA V V V mA V V V V µs V V V Note 4 : Short circuit protection is functioning only for the lower-arms. Please select the external shunt resistance such that the SC trip-level is less than 1.7 times of the current rating. 5 : Fault signal is asserted corresponding to a short circuit or lower side control supply under-voltage failure. Jun. 2005 MITSUBISHI SEMICONDUCTOR <Dual-In-Line Package Intelligent Power Module> PS21964/-A/-C TRANSFER-MOLD TYPE INSULATED TYPE MECHANICAL CHARACTERISTICS AND RATINGS Condition Parameter Mounting screw : M3 Recommended : 0.69 N·m (Note 6) Mounting torque Weight Heat-sink flatness Note 6 : Plain washers (ISO 7089~7094) are recommended. (Note 7) Min. Limits Typ. Max. 0.59 — 0.78 N·m — –50 10 — — 100 g µm Min. Limits Typ. Max. 0 13.5 13.0 –1 1.5 300 15.0 15.0 — — 400 16.5 18.5 1 — — — 7.5 — — 4.5 0.5 0.5 — — — µs 5.0 V Unit Note 7: Flatness measurement position Measurement position 4.6mm + – DIP-IPM Heat sink side – + Heat sink side RECOMMENDED OPERATION CONDITIONS Symbol Parameter VCC VD VDB ∆VD, ∆VDB tdead Supply voltage Control supply voltage Control supply voltage Control supply variation Arm shoot-through blocking time IO Output r.m.s. current PWIN(on) Allowable minimum input PWIN(off) pulse width Condition Applied between P-N Applied between VP1-VNC, VN1-VNC Applied between VUFB-U, VVFB-V, VWFB-W For each input signal, TC ≤ 100°C VCC = 300V, VD = VDB = 15V, fPWM = 5kHz P.F = 0.8, sinusoidal PWM, (Note 8) fPWM = 15kHz Tj ≤ 125°C, TC ≤ 100°C (Note 9) Unit V V V V/µs µs Arms VNC voltage variation –5.0 VNC Between VNC-N (including surge) Note 8 : The allowable r.m.s. current value depends on the actual application conditions. 9 : IPM might not make response if the input signal pulse width is less than the recommended minimum value. — — Jun. 2005 MITSUBISHI SEMICONDUCTOR <Dual-In-Line Package Intelligent Power Module> PS21964/-A/-C TRANSFER-MOLD TYPE INSULATED TYPE Fig. 6 THE DIP-IPM INTERNAL CIRCUIT DIP-IPM VUFB P HVIC VP1 VCC VUB UP UP UOUT VNC VVFB VP IGBT1 Di1 VUS COM U IGBT2 VVB Di2 VOUT VP VVS VWFB WP V VWB WP IGBT3 Di3 IGBT4 Di4 IGBT5 Di5 IGBT6 Di6 WOUT VWS W LVIC UOUT VN1 VCC VOUT UN UN VN VN WN WN Fo Fo WOUT CIN VNO VNC GND N VNO CIN Jun. 2005 MITSUBISHI SEMICONDUCTOR <Dual-In-Line Package Intelligent Power Module> PS21964/-A/-C TRANSFER-MOLD TYPE INSULATED TYPE Fig. 7 TIMING CHART OF THE DIP-IPM PROTECTIVE FUNCTIONS [A] Short-Circuit Protection (Lower-arms only with the external shunt resistor and CR filter) a1. Normal operation : IGBT ON and carrying current. a2. Short circuit detection (SC trigger). a3. IGBT gate hard interruption. a4. IGBT turns OFF. a5. FO timer starts (tFO(min) = 20µs). a6. Input “L” : IGBT OFF. a7. Input “H”. a8. IGBT OFF in spite of input “H”. Lower-arms control input a6 a7 Protection circuit state SET Internal IGBT gate RESET a3 a2 a1 SC a4 Output current Ic a8 SC reference voltage Sense voltage of the shunt resistor CR circuit time constant DELAY Error output Fo a5 [B] Under-Voltage Protection (Lower-side, UVD) b1. Control supply voltage rising : After the voltage level reaches UVDr, the circuits start to operate when next input is applied. b2. Normal operation : IGBT ON and carrying current. b3. Under voltage trip (UVDt). b4. IGBT OFF in spite of control input condition. b5. FO output (tFO ≥ 20µs and FO output continuously during UV period). b6. Under voltage reset (UVDr). b7. Normal operation : IGBT ON and carrying current. Control input Protection circuit state Control supply voltage VD RESET UVDr b1 SET UVDt b2 RESET b6 b3 b4 b7 Output current Ic Error output Fo b5 Jun. 2005 MITSUBISHI SEMICONDUCTOR <Dual-In-Line Package Intelligent Power Module> PS21964/-A/-C TRANSFER-MOLD TYPE INSULATED TYPE [C] Under-Voltage Protection (Upper-side, UVDB) c1. Control supply voltage rises : After the voltage reaches UVDBr, the circuits start to operate when next input is applied. c2. Normal operation : IGBT ON and carrying current. c3. Under voltage trip (UVDBt). c4. IGBT OFF in spite of control input signal level, but there is no FO signal output. c5. Under voltage reset (UVDBr). c6. Normal operation : IGBT ON and carrying current. Control input Protection circuit state RESET RESET SET UVDBr Control supply voltage VDB c1 UVDBt c2 c5 c3 c4 c6 Output current Ic High-level (no fault output) Error output Fo Fig. 8 RECOMMENDED MCU I/O INTERFACE CIRCUIT 5V line DIP-IPM 10kΩ UP,VP,WP,UN,VN,WN MCU 3.3kΩ (min) Fo VNC(Logic) Note : The setting of RC coupling at each input (parts shown dotted) depends on the PWM control scheme and the wiring impedance of the printed circuit board. The DIP-IPM input section integrates a 3.3kΩ (min) pull-down resistor. Therefore, when using an external filtering resistor, pay attention to the turn-on threshold voltage. Fig. 9 WIRING CONNECTION OF SHUNT RESISTOR Wiring inductance should be less than 10nH. DIP-IPM Equivalent to the inductance of a copper pattern with length=17mm, width=3mm, and thickness=100µm VNC VNO Shunt resistor N Please make the GND wiring connection of shunt resistor to the VNC terminal as close as possible. Jun. 2005 MITSUBISHI SEMICONDUCTOR <Dual-In-Line Package Intelligent Power Module> PS21964/-A/-C TRANSFER-MOLD TYPE INSULATED TYPE Fig. 10 AN EXAMPLE OF TYPICAL DIP-IPM APPLICATION CIRCUIT C1: Electrolytic capacitor with super good temperature characteristics C2,C3: 0.22~2µF R-category ceramic capacitors with super good temperature and frequency characteristics C2 C1 VUFB C2 VVFB C2 C1 C1 VWFB These wires should be connected to U, V, W terminals directly and separated from the main output wires. DIP-IPM P HVIC VP1 C3 UP VCC VUB UP UOUT U VUS VVB VP VP VOUT V VVS M VWB MCU WP VNC WP WOUT W COM VWS LVIC UOUT VN1 5V line VCC C3 VOUT UN VN WN Fo UN VN WN Long wiring here might cause short-circuit. WOUT Fo N VNC GND C VNO CIN B 15V line R1 C4 A Shunt resistor N1 Unsuitable GND wiring here might generate noise to input signal line. Note 1 2 3 4 5 6 7 8 9 10 11 Long wiring here might cause SC level fluctuation and malfunction. : To prevent malfunction, the wiring of each input should be as short as possible (2~3cm). : By virtue of integrating HVIC inside, direct coupling to MCU without opto-coupler or transformer isolation is possible. : FO output is open drain type, it should be pulled up to a 5V supply with an approximately 10kΩ resistor. : The logic of input signal is high-active. The DIP-IPM input signal section integrates a 3.3kΩ (min) pull-down resistor. If using external filtering resistor, ensure the voltage drop of ON signal not below the threshold value. : To prevent malfunction of protection, the wiring of A, B, C should be as short as possible. : Please set the filter R1C4 time constant such that the IGBT can be interrupted within 2µs. : Each capacitor should be located as nearby the pins of the DIP-IPM as possible. : To prevent surge destruction, the wiring between the smoothing capacitor and the P&N1 pins should be as short as possible. Approximately a 0.1~0.22µF snubber capacitor between the P&N1 pins is recommended. : Make external wiring connection between VNO and VNC terminals as shown in Fig.9. : Two VNC terminals (9 & 16 pin) are connected inside DIP-IPM, please connect either one to the 15V power supply GND outside and leave another one open. : It is recommended to insert a Zener diode (24V/1W) between each pair of control supply terminals to prevent surge destruction. Jun. 2005