TLC548C, TLC548I, TLC549C, TLC549I 8-BIT ANALOG-TO-DIGITAL CONVERTERS WITH SERIAL CONTROL SLAS067C – NOVEMBER 1983 – REVISED SEPTEMBER 1996 D D D D D D D D D D D D D Microprocessor Peripheral or Standalone Operation 8-Bit Resolution A/D Converter Differential Reference Input Voltages Conversion Time . . . 17 µs Max Total Access and Conversion Cycles Per Second – TLC548 . . . up to 45 500 – TLC549 . . . up to 40 000 On-Chip Software-Controllable Sample-and-Hold Function Total Unadjusted Error . . . ± 0.5 LSB Max 4-MHz Typical Internal System Clock Wide Supply Range . . . 3 V to 6 V Low Power Consumption . . . 15 mW Max Ideal for Cost-Effective, High-Performance Applications including Battery-Operated Portable Instrumentation Pinout and Control Signals Compatible With the TLC540 and TLC545 8-Bit A/D Converters and with the TLC1540 10-Bit A/D Converter CMOS Technology D OR P PACKAGE (TOP VIEW) REF + ANALOG IN REF – GND 1 8 2 7 3 6 4 5 VCC I/O CLOCK DATA OUT CS description The TLC548 and TLC549 are CMOS analog-to-digital converter (ADC) integrated circuits built around an 8-bit switched-capacitor successive-approximation ADC. These devices are designed for serial interface with a microprocessor or peripheral through a 3-state data output and an analog input. The TLC548 and TLC549 use only the input/output clock (I/O CLOCK) input along with the chip select (CS) input for data control. The maximum I/O CLOCK input frequency of the TLC548 is 2.048 MHz, and the I/O CLOCK input frequency of the TLC549 is specified up to 1.1 MHz. AVAILABLE OPTIONS PACKAGE TA SMALL OUTLINE (D) PLASTIC DIP (P) 0°C to 70°C TLC548CD TLC549CD TLC548CP TLC549CP – 40°C to 85°C TLC548ID TLC549ID TLC548IP TLC549IP Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 1996, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 TLC548C, TLC548I, TLC549C, TLC549I 8-BIT ANALOG-TO-DIGITAL CONVERTERS WITH SERIAL CONTROL SLAS067C – NOVEMBER 1983 – REVISED SEPTEMBER 1996 description (continued) Operation of the TLC548 and the TLC549 is very similar to that of the more complex TLC540 and TLC541 devices; however, the TLC548 and TLC549 provide an on-chip system clock that operates typically at 4 MHz and requires no external components. The on-chip system clock allows internal device operation to proceed independently of serial input/output data timing and permits manipulation of the TLC548 and TLC549 as desired for a wide range of software and hardware requirements. The I/O CLOCK together with the internal system clock allow high-speed data transfer and conversion rates of 45 500 conversions per second for the TLC548, and 40 000 conversions per second for the TLC549. Additional TLC548 and TLC549 features include versatile control logic, an on-chip sample-and-hold circuit that can operate automatically or under microprocessor control, and a high-speed converter with differential high-impedance reference voltage inputs that ease ratiometric conversion, scaling, and circuit isolation from logic and supply noises. Design of the totally switched-capacitor successive-approximation converter circuit allows conversion with a maximum total error of ± 0.5 least significant bit (LSB) in less than 17 µs. The TLC548C and TLC549C are characterized for operation from 0°C to 70°C. The TLC548I and TLC549I are characterized for operation from – 40°C to 85°C. functional block diagram REF + REF – 1 8-Bit Analog-to Digital Converter (SwitchedCapacitors) 3 2 ANALOG IN Sample and Hold 8 Output Data Regiser 8 4 8-to-1 Data Selector and Driver 6 DATA OUT Internal System Clock CS I/O CLOCK Control Logic and Output Counter 5 7 typical equivalent inputs INPUT CIRCUIT IMPEDANCE DURING SAMPLING MODE INPUT CIRCUIT IMPEDANCE DURING HOLD MODE 1 kΩ TYP ANALOG IN ANALOG IN Ci = 60 pF TYP (equivalent input capacitance) 2 POST OFFICE BOX 655303 5 MΩ TYP • DALLAS, TEXAS 75265 TLC548C, TLC548I, TLC549C, TLC549I 8-BIT ANALOG-TO-DIGITAL CONVERTERS WITH SERIAL CONTROL SLAS067C – NOVEMBER 1983 – REVISED SEPTEMBER 1996 operating sequence 1 2 3 4 5 6 7 8 1 Don’t I/O CLOCK Access Cycle B tsu(CS) 3 4 5 6 7 8 Care Access Cycle C tconv Sample Cycle B 2 (see Note A) Sample Cycle C tsu(CS) CS twH(CS) DATA OUT Hi-Z State Hi-Z State A7 A6 A5 A4 A3 A2 A1 A0 B7 B6 B5 B4 B3 B2 B1 B0 B7 A7 Previous Conversion Data A MSB LSB (see Note B) Conversion Data B MSB ten MSB LSB MSB ten NOTES: A. The conversion cycle, which requires 36 internal system clock periods (17 µs maximum), is initiated with the eighth I/O clock pulse trailing edge after CS goes low for the channel whose address exists in memory at the time. B. The most significant bit (A7) is automatically placed on the DATA OUT bus after CS is brought low. The remaining seven bits (A6–A0) are clocked out on the first seven I/O clock falling edges. B7–B0 follows in the same manner. absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.5 V Input voltage range at any input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to VCC + 0.3 V Output voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to VCC + 0.3 V Peak input current range (any input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 10 mA Peak total input current range (all inputs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 30 mA Operating free-air temperature range, TA (see Note 2): TLC548C, TLC549C . . . . . . . . . . . . . 0°C to 70°C TLC548I, TLC549I . . . . . . . . . . . . – 40°C to 85°C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C NOTES: 1. All voltage values are with respect to the network ground terminal with the REF– and GND terminals connected together, unless otherwise noted. 2. The D package is not recommended below – 40°C. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 TLC548C, TLC548I, TLC549C, TLC549I 8-BIT ANALOG-TO-DIGITAL CONVERTERS WITH SERIAL CONTROL SLAS067C – NOVEMBER 1983 – REVISED SEPTEMBER 1996 recommended operating conditions TLC548 MIN Supply voltage, VCC 3 Positive reference voltage, Vref+ (see Note 3) 2.5 Negative reference voltage, Vref – (see Note 3) – 0.1 Differential reference voltage, Vref+, Vref – (see Note 3) 1 Analog input voltage (see Note 3) 0 High-level control input voltage, VIH (for VCC = 4.75 V to 5.5 V) 2 MAX 5 6 VCC VCC+0.1 0 2.5 VCC VCC+0.2 VCC Low-level control input voltage, VIL (for VCC = 4.75 V to 5.5 V) Input/output clock frequency, fclock(I/O) (for VCC = 4.75 V to 5.5 V) TLC549 NOM MIN 3 2.5 –0.1 1 0 MAX 5 6 2.048 0 UNIT V VCC VCC+0.1 0 2.5 V VCC VCC+0.2 VCC V 2 0.8 0 NOM V V V 0.8 V 1.1 MHz Input/output clock high, twH(I/O) (for VCC = 4.75 V to 5.5 V) 200 404 ns Input/output clock low, twL(I/O) (for VCC = 4.75 V to 5.5 V) 200 404 ns Input/output clock transition time, tt(I/O) (for VCC = 4.75 V to 5.5 V) (see Note 4 and Operating Sequence) Duration of CS input high state during conversion, twH(CS) (for VCC = 4.75 V to 5.5 V) (see Operating Sequence) Setup time, CS low before first I/O CLOCK, tsu(CS) (for VCC = 4.75 V to 5.5 V) (see Note 5) TLC548C, TLC549C TLC548I, TLC549I 100 100 ns 17 17 µs 1.4 1.4 µs 0 70 0 70 – 40 85 – 40 85 °C NOTES: 3. Analog input voltages greater than that applied to REF+ convert to all ones (11111111), while input voltages less than that applied to REF– convert to all zeros (00000000). For proper operation, the positive reference voltage Vref+, must be at least 1 V greater than the negative reference voltage, Vref–. In addition, unadjusted errors may increase as the differential reference voltage, Vref+ – Vref– , falls below 4.75 V. 4. This is the time required for the I/O CLOCK input signal to fall from VIH min to VIL max or to rise from VIL max to VIH min. In the vicinity of normal room temperature, the devices function with input clock transition time as slow as 2 µs for remote data acquisition applications in which the sensor and the ADC are placed several feet away from the controlling microprocessor. 5. To minimize errors caused by noise at the CS input, the internal circuitry waits for two rising edges and one falling edge of internal system clock after CS↓ before responding to control input signals. This CS setup time is given by the ten and tsu(CS) specifications. 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TLC548C, TLC548I, TLC549C, TLC549I 8-BIT ANALOG-TO-DIGITAL CONVERTERS WITH SERIAL CONTROL SLAS067C – NOVEMBER 1983 – REVISED SEPTEMBER 1996 electrical characteristics over recommended operating free-air temperature range, VCC = Vref+ = 4.75 V to 5.5 V, fclock(I/O) = 2.048 MHz for TLC548 or 1.1 MHz for TLC549 (unless otherwise noted) PARAMETER VOH VOL TEST CONDITIONS High-level output voltage Low-level output voltage IOZ High impedance off High-impedance off-state state output current IIH IIL High-level input current, control inputs II( I(on)) ICC ICC + Iref Ci MAX VO = VCC, VO = 0, CS at VCC 10 CS at VCC – 10 VI = VCC VI = 0 Analog g channel on-state input current during g sample cycle Analog input at VCC Analog input at 0 V Operating supply current Input capacitance TYP† IOH = – 360 µA IOL = 3.2 mA Low-level input current, control inputs Supply and reference current MIN VCC = 4.75 V, VCC = 4.75 V, 2.4 UNIT V 0.4 V µA 0.005 2.5 µA – 0.005 – 2.5 µA 0.4 1 – 0.4 –1 CS at 0 V 1.8 2.5 mA Vref+ = VCC mA 1.9 3 Analog inputs 7 55 Control inputs 5 15 µA pF operating characteristics over recommended operating free-air temperature range, VCC = Vref+ = 4.75 V to 5.5 V, fclock(I/O) = 2.048 MHz for TLC548 or 1.1 MHz for TLC549 (unless otherwise noted) TLC548 PARAMETER TEST CONDITIONS MIN TYP† MAX MIN TLC549 TYP† MAX UNIT EL EZS Linearity error See Note 6 ±0.5 ±0.5 LSB Zero-scale error See Note 7 ±0.5 ±0.5 LSB EFS Full-scale error See Note 7 ±0.5 ±0.5 LSB Total unadjusted error See Note 8 ±0.5 LSB Conversion time See Operating Sequence 8 17 12 17 Total access and conversion time See Operating Sequence 12 22 19 25 µs 4 I/O clock cycles tconv ta Channel acquisition time (sample cycle) tv Time output data remains valid after I/O CLOCK↓ ±0.5 See Operating Sequence 4 10 ns td ten Delay time to data output valid 200 400 ns Output enable time 1.4 1.4 µs tdis tr(bus) Output disable time 150 150 ns 300 300 ns Data bus rise time I/O CLOCK↓ 10 µs See Figure 1 tf(bus) Data bus fall time 300 300 ns † All typicals are at VCC = 5 V, TA = 25°C. NOTES: 6. Linearity error is the deviation from the best straight line through the A/D transfer characteristics. 7. Zero-scale error is the difference between 00000000 and the converted output for zero input voltage; full-scale error is the difference between 11111111 and the converted output for full-scale input voltage. 8. Total unadjusted error is the sum of linearity, zero-scale, and full-scale errors. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 TLC548C, TLC548I, TLC549C, TLC549I 8-BIT ANALOG-TO-DIGITAL CONVERTERS WITH SERIAL CONTROL SLAS067C – NOVEMBER 1983 – REVISED SEPTEMBER 1996 PARAMETER MEASUREMENT INFORMATION VCC 1.4 V 3 kΩ 3 kΩ Test Point Output Under Test Test Point Output Under Test 3 kΩ CL (see Note A) CL (see Note A) Test Point Output Under Test CL (see Note A) See Note B See Note B LOAD CIRCUIT FOR td, tr, AND tf LOAD CIRCUIT FOR tPZH AND tPHZ LOAD CIRCUIT FOR tPZL AND tPLZ VCC 50% CS 50% 0V tPZL Output Waveform 1 (see Note C) tPLZ VCC 50% 10% tPZH Output Waveform 2 (see Note C) 0V tPHZ 90% 50% VOH 0V See Note B VOLTAGE WAVEFORMS FOR ENABLE AND DISABLE TIMES I/O CLOCK 0.8 V 2.4 V Output 0.4 V td 2.4 V DATA OUT 0.8 V tr(bus) tf(bus) VOLTAGE WAVEFORMS FOR RISE AND FALL TIMES VOLTAGE WAVEFORMS FOR DELAY TIME NOTES: A. CL = 50 pF for TLC548 and 100 pF for TLC549; CL includes jig capacitance. B. ten = tPZH or tPZL, tdis = tPHZ or tPLZ. C. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. Figure 1. Load Circuits and Voltage Waveforms 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TLC548C, TLC548I, TLC549C, TLC549I 8-BIT ANALOG-TO-DIGITAL CONVERTERS WITH SERIAL CONTROL SLAS067C – NOVEMBER 1983 – REVISED SEPTEMBER 1996 APPLICATIONS INFORMATION simplified analog input analysis Using the equivalent circuit in Figure 2, the time required to charge the analog input capacitance from 0 to VS within 1/2 LSB can be derived as follows: The capacitance charging voltage is given by ( VC = VS 1– e – tc /RtCi ) (1) where Rt = Rs + ri The final voltage to 1/2 LSB is given by VC (1/2 LSB) = VS – (VS /512) (2) Equating equation 1 to equation 2 and solving for time tc gives ( VS – (VS/512) = VS 1– e – tc /RtCi ) (3) and tc (1/2 LSB) = Rt × Ci × ln(512) (4) Therefore, with the values given the time for the analog input signal to settle is tc (1/2 LSB) = (Rs + 1 kΩ) × 60 pF × ln(512) (5) This time must be less than the converter sample time shown in the timing diagrams. Driving Source† TLC548/9 Rs VS VI ri VC 1 kΩ MAX Ci 55 pF MAX VI = Input Voltage at ANALOG IN VS = External Driving Source Voltage Rs = Source Resistance ri = Input Resistance Ci = Input Capacitance † Driving source requirements: • Noise and distortion for the source must be equivalent to the resolution of the converter. • Rs must be real at the input frequency. Figure 2. Equivalent Input Circuit Including the Driving Source POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7 TLC548C, TLC548I, TLC549C, TLC549I 8-BIT ANALOG-TO-DIGITAL CONVERTERS WITH SERIAL CONTROL SLAS067C – NOVEMBER 1983 – REVISED SEPTEMBER 1996 PRINCIPLES OF OPERATION The TLC548 and TLC549 are each complete data acquisition systems on a single chip. Each contains an internal system clock, sample-and-hold function, 8-bit A/D converter, data register, and control logic circuitry. For flexibility and access speed, there are two control inputs: I/O CLOCK and chip select (CS). These control inputs and a TTL-compatible 3-state output facilitate serial communications with a microprocessor or minicomputer. A conversion can be completed in 17 µs or less, while complete input-conversion-output cycles can be repeated in 22 µs for the TLC548 and in 25 µs for the TLC549. The internal system clock and I/O CLOCK are used independently and do not require any special speed or phase relationships between them. This independence simplifies the hardware and software control tasks for the device. Due to this independence and the internal generation of the system clock, the control hardware and software need only be concerned with reading the previous conversion result and starting the conversion by using the I/O clock. In this manner, the internal system clock drives the “conversion crunching” circuitry so that the control hardware and software need not be concerned with this task. When CS is high, DATA OUT is in a high-impedance condition and I/O CLOCK is disabled. This CS control function allows I/O CLOCK to share the same control logic point with its counterpart terminal when additional TLC548 and TLC549 devices are used. This also serves to minimize the required control logic terminals when using multiple TLC548 and TLC549 devices. The control sequence has been designed to minimize the time and effort required to initiate conversion and obtain the conversion result. A normal control sequence is: 1. CS is brought low. To minimize errors caused by noise at CS, the internal circuitry waits for two rising edges and then a falling edge of the internal system clock after a CS↓ before the transition is recognized. However, upon a CS rising edge, DATA OUT goes to a high-impedance state within the specified tdis even though the rest of the integrated circuitry does not recognize the transition until the specified tsu(CS) has elapsed. This technique protects the device against noise when used in a noisy environment. The most significant bit (MSB) of the previous conversion result initially appears on DATA OUT when CS goes low. 2. The falling edges of the first four I/O CLOCK cycles shift out the second, third, fourth, and fifth most significant bits of the previous conversion result. The on-chip sample-and-hold function begins sampling the analog input after the fourth high-to-low transition of I/O CLOCK. The sampling operation basically involves the charging of internal capacitors to the level of the analog input voltage. 3. Three more I/O CLOCK cycles are then applied to the I/O CLOCK terminal and the sixth, seventh, and eighth conversion bits are shifted out on the falling edges of these clock cycles. 4. The final (the eighth) clock cycle is applied to I/O CLOCK. The on-chip sample-and-hold function begins the hold operation upon the high-to-low transition of this clock cycle. The hold function continues for the next four internal system clock cycles, after which the holding function terminates and the conversion is performed during the next 32 system clock cycles, giving a total of 36 cycles. After the eighth I/O CLOCK cycle, CS must go high or the I/O clock must remain low for at least 36 internal system clock cycles to allow for the completion of the hold and conversion functions. CS can be kept low during periods of multiple conversion. When keeping CS low during periods of multiple conversion, special care must be exercised to prevent noise glitches on the I/O CLOCK line. If glitches occur on I/O CLOCK, the I/O sequence between the microprocessor/controller and the device loses synchronization. When CS is taken high, it must remain high until the end of conversion. Otherwise, a valid high-to-low transition of CS causes a reset condition, which aborts the conversion in progress. A new conversion may be started and the ongoing conversion simultaneously aborted by performing steps 1 through 4 before the 36 internal system clock cycles occur. Such action yields the conversion result of the previous conversion and not the ongoing conversion. 8 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TLC548C, TLC548I, TLC549C, TLC549I 8-BIT ANALOG-TO-DIGITAL CONVERTERS WITH SERIAL CONTROL SLAS067C – NOVEMBER 1983 – REVISED SEPTEMBER 1996 PRINCIPLES OF OPERATION For certain applications, such as strobing applications, it is necessary to start conversion at a specific point in time. This device accommodates these applications. Although the on-chip sample-and-hold function begins sampling upon the high-to-low transition of the fourth I/O CLOCK cycle, the hold function does not begin until the high-to-low transition of the eighth I/O CLOCK cycle, which should occur at the moment when the analog signal must be converted. The TLC548 and TLC549 continue sampling the analog input until the high-to-low transition of the eighth I/O CLOCK pulse. The control circuitry or software then immediately lowers I/O CLOCK and starts the holding function to hold the analog signal at the desired point in time and starts the conversion. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 9 PACKAGE OPTION ADDENDUM www.ti.com 22-Feb-2005 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty TLC548CD ACTIVE SOIC D 8 75 Pb-Free (RoHS) CU NIPDAU Level-2-260C-1YEAR/ Level-1-220C-UNLIM TLC548CDR ACTIVE SOIC D 8 2500 Pb-Free (RoHS) CU NIPDAU Level-2-260C-1YEAR/ Level-1-220C-UNLIM TLC548CP ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU Level-NC-NC-NC TLC548ID ACTIVE SOIC D 8 75 Pb-Free (RoHS) CU NIPDAU Level-2-260C-1YEAR/ Level-1-220C-UNLIM TLC548IDR ACTIVE SOIC D 8 2500 Pb-Free (RoHS) CU NIPDAU Level-2-260C-1YEAR/ Level-1-220C-UNLIM TLC548IP ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU Level-NC-NC-NC TLC549CD ACTIVE SOIC D 8 75 Pb-Free (RoHS) CU NIPDAU Level-2-260C-1YEAR/ Level-1-220C-UNLIM TLC549CDR ACTIVE SOIC D 8 2500 Pb-Free (RoHS) CU NIPDAU Level-2-260C-1YEAR/ Level-1-220C-UNLIM TLC549CP ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU Level-NC-NC-NC TLC549ID ACTIVE SOIC D 8 75 Pb-Free (RoHS) CU NIPDAU Level-2-260C-1YEAR/ Level-1-220C-UNLIM TLC549IDR ACTIVE SOIC D 8 2500 Pb-Free (RoHS) CU NIPDAU Level-2-260C-1YEAR/ Level-1-220C-UNLIM TLC549IP ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU Level-NC-NC-NC Lead/Ball Finish MSL Peak Temp (3) TLC549IPS ACTIVE SO PS 8 80 None CU NIPDAU Level-1-220C-UNLIM TLC549IPSR ACTIVE SO PS 8 2000 None CU NIPDAU Level-1-220C-UNLIM TLC549MP OBSOLETE PDIP P 8 None Call TI Call TI (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - May not be currently available - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. None: Not yet available Lead (Pb-Free). Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Green (RoHS & no Sb/Br): TI defines "Green" to mean "Pb-Free" and in addition, uses package materials that do not contain halogens, including bromine (Br) or antimony (Sb) above 0.1% of total product weight. (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDECindustry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 22-Feb-2005 information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2005, Texas Instruments Incorporated