MBRB30H30CT−1 SWITCHMODE™ Power Rectifier 30 V, 30 A Features and Benefits • • • • • • • http://onsemi.com Low Forward Voltage Low Power Loss/High Efficiency High Surge Capacity 150°C Operating Junction Temperature 30 A Total (15 A Per Diode Leg) Guard−Ring for Stress Protection This is a Pb−Free Device* SCHOTTKY BARRIER RECTIFIER 30 AMPERES, 30 VOLTS 1 2, 4 Applications 3 • Power Supply − Output Rectification • Power Management • Instrumentation MARKING DIAGRAM 4 Mechanical Characteristics: • • • • • Case: Epoxy, Molded Epoxy Meets UL 94 V−0 @ 0.125 in Weight: 1.5 Grams (Approximately) Finish: All External Surfaces Corrosion Resistant and Terminal Leads are Readily Solderable Lead Temperature for Soldering Purposes: 260°C Max. for 10 Seconds MAXIMUM RATINGS I2PAK (TO−262) CASE 418D PLASTIC AYWW B30H30G AKA 12 3 B30H30 A Y WW G AKA = Device Code = Assembly Location = Year = Work Week = Pb−Free Package = Polarity Designator Please See the Table on the Following Page ORDERING INFORMATION Device Package Shipping MBRB30H30CT−1G TO−262 (Pb−Free) 50 Units/Rail *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. © Semiconductor Components Industries, LLC, 2007 March, 2007 − Rev. 1 1 Publication Order Number: MBRB30H30CT−1/D MBRB30H30CT−1 MAXIMUM RATINGS (Per Diode Leg) Rating Symbol Value Unit Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage VRRM VRWM VR 30 V Average Rectified Forward Current (Rated VR) TC = 138°C IF(AV) 15 A Peak Repetitive Forward Current (Rated VR, Square Wave, 20 kHz) IFRM 30 A Nonrepetitive Peak Surge Current (Surge applied at rated load conditions halfwave, single phase, 60 Hz) IFSM 260 A TJ −55 to +150 °C Storage Temperature Tstg *55 to +150 °C Voltage Rate of Change (Rated VR) dv/dt 10,000 V/ms WAVAL 250 mJ > 400 > 8000 V 2.0 70 °C/W Operating Junction Temperature (Note 1) Controlled Avalanche Energy (see test conditions in Figures 9 and 10) ESD Ratings: Machine Model = C Human Body Model = 3B THERMAL CHARACTERISTICS Maximum Thermal Resistance − Junction−to−Case − Junction−to−Ambient RqJC RqJA ELECTRICAL CHARACTERISTICS (Per Diode Leg) Maximum Instantaneous Forward Voltage (Note 2) (IF = 15 A, TC = 25°C) (IF = 15 A, TC = 125°C) (IF = 30 A, TC = 25°C) (IF = 30 A, TC = 125°C) vF Maximum Instantaneous Reverse Current (Note 2) (Rated DC Voltage, TC = 25°C) (Rated DC Voltage, TC = 125°C) iR V 0.48 0.40 0.55 0.53 mA 0.8 130 Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. The heat generated must be less than the thermal conductivity from Junction−to−Ambient: dPD/dTJ < 1/RqJA. 2. Pulse Test: Pulse Width = 300 ms, Duty Cycle ≤ 2.0%. http://onsemi.com 2 IF, INSTANTANEOUS FORWARD CURRENT (AMPS) IF, INSTANTANEOUS FORWARD CURRENT (AMPS) MBRB30H30CT−1 100 TJ = 125°C 10 TJ = 25°C 1 0.1 0 0.1 0.2 0.4 0.3 0.5 0.6 0.7 0.8 0.9 1.0 VF, INSTANTANEOUS FORWARD VOLTAGE (VOLTS) 100 TJ = 125°C 10 TJ = 25°C 1 0.1 0 0.1 1.0E−01 TJ = 125°C 0.6 0.7 0.8 0.9 1.0 TJ = 125°C 1.0E−02 1.0E−03 1.0E−03 TJ = 25°C 1.0E−04 5 10 15 1.0E−04 25 20 30 1.0E−05 0 TJ = 25°C 5 10 15 20 25 VR, REVERSE VOLTAGE (VOLTS) VR, REVERSE VOLTAGE (VOLTS) Figure 3. Typical Reverse Current Figure 4. Maximum Reverse Current 30 PFO, AVERAGE POWER DISSIPATION (WATTS) IF, AVERAGE FORWARD CURRENT (AMPS) 0.5 1.0E−01 1.0E−02 dc 25 SQUARE WAVE 15 10 5 0 100 0.4 1.0E−00 IR, REVERSE CURRENT (AMPS) 1.0E−00 20 0.3 Figure 2. Maximum Forward Voltage IR, MAXIMUM REVERSE CURRENT (AMPS) Figure 1. Typical Forward Voltage 1.0E−05 0 0.2 VF, INSTANTANEOUS FORWARD VOLTAGE (VOLTS) 110 120 130 140 150 160 16 14 12 SQUARE 10 8 DC 6 4 2 0 0 5 10 15 20 TC, CASE TEMPERATURE (°C) IO, AVERAGE FORWARD CURRENT (AMPS) Figure 5. Current Derating Figure 6. Forward Power Dissipation http://onsemi.com 3 30 25 MBRB30H30CT−1 10000 C, CAPACITANCE (pF) TJ = 25°C 1000 100 0 5 10 15 20 25 30 VR, REVERSE VOLTAGE (VOLTS) R(t), TRANSIENT THERMAL RESISTANCE Figure 7. Capacitance 10 1 D = 0.5 0.2 0.1 0.05 P(pk) 0.1 t1 0.01 SINGLE PULSE 0.01 0.000001 0.00001 t2 DUTY CYCLE, D = t1/t2 0.0001 0.001 0.01 0.1 1 t1, TIME (sec) Figure 8. Thermal Response Junction−to−Case http://onsemi.com 4 10 100 1000 MBRB30H30CT−1 +VDD IL 10 mH COIL BVDUT VD MERCURY SWITCH S1 ID ID IL DUT VDD t0 Figure 9. Test Circuit t1 t2 t Figure 10. Current−Voltage Waveforms elements are small Equation (1) approximates the total energy transferred to the diode. It can be seen from this equation that if the VDD voltage is low compared to the breakdown voltage of the device, the amount of energy contributed by the supply during breakdown is small and the total energy can be assumed to be nearly equal to the energy stored in the coil during the time when S1 was closed, Equation (2). The unclamped inductive switching circuit shown in Figure 9 was used to demonstrate the controlled avalanche capability of this device. A mercury switch was used instead of an electronic switch to simulate a noisy environment when the switch was being opened. When S1 is closed at t0 the current in the inductor IL ramps up linearly; and energy is stored in the coil. At t1 the switch is opened and the voltage across the diode under test begins to rise rapidly, due to di/dt effects, when this induced voltage reaches the breakdown voltage of the diode, it is clamped at BVDUT and the diode begins to conduct the full load current which now starts to decay linearly through the diode, and goes to zero at t2. By solving the loop equation at the point in time when S1 is opened; and calculating the energy that is transferred to the diode it can be shown that the total energy transferred is equal to the energy stored in the inductor plus a finite amount of energy from the VDD power supply while the diode is in breakdown (from t1 to t2) minus any losses due to finite component resistances. Assuming the component resistive EQUATION (1): ǒ BV 2 DUT W [ 1 LI LPK AVAL 2 BV –V DUT DD EQUATION (2): 2 W [ 1 LI LPK AVAL 2 http://onsemi.com 5 Ǔ MBRB30H30CT−1 PACKAGE DIMENSIONS I2PAK (TO−262) CASE 418D−01 ISSUE C C E V −B− 4 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. A W 1 2 3 F −T− SEATING PLANE K S J H 3 PL 0.13 (0.005) M T B INCHES MIN MAX 0.335 0.380 0.380 0.406 0.160 0.185 0.026 0.035 0.045 0.055 0.122 REF 0.100 BSC 0.094 0.110 0.013 0.025 0.500 0.562 0.390 REF 0.045 0.070 0.522 0.551 MILLIMETERS MIN MAX 8.51 9.65 9.65 10.31 4.06 4.70 0.66 0.89 1.14 1.40 3.10 REF 2.54 BSC 2.39 2.79 0.33 0.64 12.70 14.27 9.90 REF 1.14 1.78 13.25 14.00 STYLE 3: PIN 1. ANODE 2. CATHODE 3. ANODE G D DIM A B C D E F G H J K S V W M SWITCHMODE is a trademark of Semiconductor Components Industries, LLC. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 http://onsemi.com 6 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MBRB30H30CT−1/D