Filename: tfs 167h.doc Version 1.4 VI TELEFILTER 19.08.2004 Filter specification TFS 167H 1/5 Measurement condition Ambient temperature: Input power level: Terminating impedance: * Input: Output: 23 0 °C dBm 348 348 || - 7,2 pF || - 7,2 pF Characteristics Remark: The reference level for the relative attenuation a rel of the TFS 167H is the maximum attenuation in the pass band. The maximum attenuation in the pass band is defined as the insertion loss ae. The nominal frequency fN is fixed at 167,0 MHz without any tolerance or limit. The values of relative attenuation arel are guaranteed for the whole operating temperature range. The frequency shift of the filter in the operating temperature range is included in the production tolerance scheme. Data Insertion loss (Reference level) typ. value ae 1,4 Nominal frequency fN - Pass band PB - Amplitude variation in PB p-p Relative attenuation fN 0,4 MHz ... fN 0,6 0,6 MHz ... fN 20,0 fN fN - 20 MHz ... fN - 137 fN + 20 MHz ... fN + 103 fN +103 MHz ... fN + 105 fN +105 MHz ... fN + 833 arel MHz MHz MHz MHz MHz MHz Group delay ripple in PB Intermodulation ratio For two 20dBm input signals @ fN + 0,800 MHz and fN + 1,600 @ fN - 0,800 MHz and fN - 1,600 MHz MHz 3,0 dB 167,0 MHz 75 dB max. 1 0,25 dB max. 0,5 dB 9,0 18,0 56 43 65 46 Absolute group delay in PB max. fN 0,3 Amplitude ripple in PB dB tolerance / limit dB dB dB dB dB dB min. min. min. min. min. min. 1,75 µs max. 5 10 33 33 40 33 kHz dB dB dB dB dB dB dB 2,0 µs 210 ns max. 300 ns 110 110 dB dB min. 100 min. 100 dB dB Input Return loss 18,0 dB min. 15,0 dB Output Return loss 19,0 dB min. 10,0 dB max. 22 Input power level - Temperature coefficient of frequency Tc f ** -0,046 ppm/K² Frequency inversion temperature 20 dBm - °C - Operating temperature range - - 5 °C .. + 85 °C Storage temperature range - - 40 °C.. + 90 °C *) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values only. Should there be additional questions do not hesitate to ask for an application note or contact our design team. **) fc(Hz) = Tcf(ppm/K²) x (T - To)² x fCAT (MHz). generated: checked / approved: Tele Filter GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. [email protected] Filename: tfs 167h.doc Version 1.4 VI TELEFILTER 19.08.2004 Filter specification TFS 167H 3/5 Stability characteristics After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 18 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0,35 mm or 5 g respectively, 1 octave per min, 10 cycles per plan, 3 plans; DIN IEC 68 T2 - 6 3. Change of temperature: 4. Resistance to solder heat (reflow): 5. ESD -55 °C to 125°C / 30 min. each / 10 cycles DIN IEC 68 part 2 14 Test N reflow possible: twice max.; for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4; MIL-STD-883E using coupling network of ISO 10605 and EN 6100-4-2 HBM:500V; MM:500V; Packing Tape & Reel: IEC 286 3, with exeption of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters peer reel: reel of empty components at start: reel of empty components at start including leader: trailer: 3000 min. 300 mm min. 500 mm min. 300 mm Pull Off Direction Tape (all dimensions in mm) W : 16,00 ± 0,3 Po : 4,00 ± 0,1 Do : 1,50 +0,1/-0 E : 1,75 ± 0,10 F : 7,50 ± 0,10 G(min) : 0,60 P2 : 2,00 ± 0,1 P1 : 12,00 ± 0,1 D1(min) : 1,50 Ao : 7,60 ± 0,10 Bo : 9,60 ± 0,10 Ct : 13,5 P1 t Date Code Do Ko Typ Po PIN Marker P2 D1 Ao W 2 Reel (all dimensions in mm) A : 330 W1 : 18,0 W2(max) : 22,0 N(min) : 100 C : 13,0 A C N W 1 The minimum bending radius is 45 mm. Tele Filter GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 167h.doc Version 1.4 VI TELEFILTER 19.08.2004 Filter specification TFS 167H 4/5 Air reflow temperature conditions 1st and 2nd air reflow profile Name: Temperature: Time: pre-heating periods 150 °C - 170 °C 60 sec. - 90 sec. main-heating periods over 200 °C 20 sec. - 25 sec. peak temperature 255 °C ± 5 °C Chip-mount air reflow profile 260 240 220 200 temperature / °C 180 160 140 120 100 80 60 40 20 0 0 20 40 60 80 100 120 140 160 180 200 220 240 time / s ec. Table for temperature vs. time during the air reflow process Tolerance of temperatures: ± 5 °C time / sec. 0 10 20 30 40 50 60 70 80 90 100 110 120 130 temperature / °C 23 34 46 60 80 103 121 134 143 150 154 156 158 159 time / sec. 140 150 160 170 180 190 195 200 205 210 215 220 230 240 temperature / °C 160 161 164 170 180 205 230 255 230 205 180 165 140 120 Tele Filter GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 167h.doc VI TELEFILTER Version 1.4 Filter specification 19.08.2004 TFS 167H 5/5 History Version Reason of Changes Name Date 1.0 generate preliminary specification Roizengaft 18.11.2003 1.1 generation of filter specification add terminating impedance add filter characteristic change circuit test change packing (tape and reel) Noack 16.04.2004 correction terminating impedance add typical value for amplitude ripple amplitude variation change packing (tape) change temperature coefficient Noack 18.06.2004 change limit of relative attenuation from 30 dB to 33dB update typical value and filter characteristic Noack 16.07.2004 add ESD stability characteristics change drawing of packing (tape and reel) Noack 19.08.2004 1.2 1.3 1.4 Tele Filter GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.