AMC1200 SBAS542A – APRIL 2011 – REVISED AUGUST 2011 www.ti.com Fully-Differential Isolation Amplifier Check for Samples: AMC1200 FEATURES DESCRIPTION • The AMC1200 is a precision isolation amplifier with an output separated from the input circuitry by a silicon dioxide (SiO2) barrier that is highly resistant to magnetic interference. This barrier has been certified to provide galvanic isolation of up to 4000 VPEAK according to UL1577 and IEC60747-5-2. Used in conjunction with isolated power supplies, this device prevents noise currents on a high common-mode voltage line from entering the local ground and interfering with or damaging sensitive circuitry. 1 2 • • • • • • • • • • • ±250-mV Input Voltage Range Optimized for Shunt Resistors Very Low Nonlinearity: 0.075% max at 5 V Low Offset Error: 1.5 mV max Low Noise: 3.1 mVRMS typ Low High-Side Supply Current: 8 mA max at 5V Input Bandwidth: 60 kHz min Fixed Gain: 8 (0.5% accuracy) High Common-Mode Rejection Ratio: 108 dB 3.3-V Operation on Low-Side Certified Galvanic Isolation: – UL1577 and IEC60747-5-2 Approved – Isolation Voltage: 4000 VPEAK – Working Voltage: 1200 VPEAK – Transient Immunity: 10 kV/µs min Typical 10-Year Lifespan at Rated Working Voltage (see Application Report SLLA197) Fully Specified Over the Extended Industrial Temperature Range The input of the AMC1200 is optimized for direct connection to shunt resistors or other low voltage level signal sources. The excellent performance of the device supports accurate current control resulting in system-level power saving and, especially in motor-control applications, lower torque ripple. The common-mode voltage of the output signal is automatically adjusted to either the 3-V or 5-V low-side supply. The AMC1200 is fully specified over the extended industrial temperature range of –40 °C to +105 °C and is available in the SMD-type, gullwing-8 package. APPLICATIONS • Shunt Resistor Based Current Sensing in: – Motor Control – Green Energy – Frequency Inverters – Uninterruptible Power Supplies VDD1 VDD2 5V 2.55 V 0V VINP VOUTP VINN VOUTN 2V 250 mV 3.3 V 1.29 V GND1 2V GND2 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2011, Texas Instruments Incorporated AMC1200 SBAS542A – APRIL 2011 – REVISED AUGUST 2011 www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PACKAGE/ORDERING INFORMATION For the most current package and ordering information see the Package Option Addendum at the end of this document, or visit the device product folder on www.ti.com. ABSOLUTE MAXIMUM RATINGS (1) Over the operating ambient temperature range, unless otherwise noted. Supply voltage, VDD1 to GND1 or VDD2 to GND2 Analog input voltage at VINP, VINN Input current to any pin except supply pins (1) UNIT –0.5 to 6 V GND1 – 0.5 to VDD1 + 0.5 V ±10 mA +150 °C Human body model (HBM) JEDEC standard 22, test method A114-C.01 ±2500 V Charged device model (CDM) JEDEC standard 22, test method C101 ±1000 V Maximum junction temperature, TJ Max Electrostatic discharge (ESD) ratings, all pins AMC1200 Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated is not implied. Exposure to absolute maximum rated conditions for extended periods may affect device reliability. THERMAL INFORMATION AMC1200 THERMAL METRIC (1) DUB (SOP) UNITS 8 PINS θJA Junction-to-ambient thermal resistance 75.1 θJCtop Junction-to-case (top) thermal resistance 61.6 θJB Junction-to-board thermal resistance 39.8 ψJT Junction-to-top characterization parameter 27.2 ψJB Junction-to-board characterization parameter 39.4 θJCbot Junction-to-case (bottom) thermal resistance N/A (1) °C/W For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953. REGULATORY INFORMATION 2 VDE/IEC UL Certified according to IEC 60747-5-2 Recognized under 1577 component recognition program File number: 40016131 File number: E181974 Copyright © 2011, Texas Instruments Incorporated AMC1200 SBAS542A – APRIL 2011 – REVISED AUGUST 2011 www.ti.com IEC 60747-5-2 INSULATION CHARACTERISTICS Over operating free-air temperature range (unless otherwise noted). PARAMETER VIORM VPR VALUE UNIT Maximum working insulation voltage Input to output test voltage VIOTM TEST CONDITIONS Transient overvoltage VISO Insulation voltage per UL RS Insulation resistance PD Pollution degree 1200 VPEAK Qualification test: after Input/Output Safety Test Subgroup 2/3 VPR = VIORM x 1.2, t = 10 s, partial discharge < 5 pC 1140 VPEAK Qualification test: method a, after environmental tests subgroup 1, VPR = VIORM x 1.6, t = 10 s, partial discharge < 5 pC 1920 VPEAK 100% production test: method b1, VPR = VIORM x 1.875, t = 1 s, partial discharge < 5 pC 2250 VPEAK Qualification test: t = 60 s 4000 VPEAK Qualification test: VTEST = VISO , t = 60 s 4000 VPEAK 100% production test: VTEST = 1.2 x VISO , t = 1 s 4800 VPEAK VIO = 500 V at TS > 109 Ω 2 ° IEC SAFETY LIMITING VALUES Safety limiting intends to prevent potential damage to the isolation barrier upon failure of input or output (I/O) circuitry. A failure of the I/O circuitry can allow low resistance to ground or the supply and, without current limiting, dissipate sufficient power to overheat the die and damage the isolation barrier, potentially leading to secondary system failures. The safety-limiting constraint is the operating virtual junction temperature range specified in the Absolute Maximum Ratings table. The power dissipation and junction-to-air thermal impedance of the device installed in the application hardware determine the junction temperature. The assumed junction-to-air thermal resistance in the Thermal Information table is that of a device installed in the JESD51-3, Low Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages and is conservative. The power is the recommended maximum input voltage times the current. The junction temperature is then the ambient temperature plus the power times the junction-to-air thermal resistance. PARAMETER IS Safety input, output, or supply current TC Maximum case temperature TEST CONDITIONS MIN TYP θJA = 246°C/W, VIN = 5.5 V, TJ = +150°C, TA = +25°C MAX UNIT 10 mA +150 °C IEC 61000-4-5 RATINGS PARAMETER VIOSM Surge immunity TEST CONDITIONS 1.2-μs/50-μs voltage surge and 8-μs/20-μs current surge VALUE UNIT ±6000 V IEC 60664-1 RATINGS PARAMETER Basic isolation group Installation classification Copyright © 2011, Texas Instruments Incorporated TEST CONDITIONS Material group SPECIFICATION II Rated mains voltage ≤ 150 VRMS I-IV Rated mains voltage ≤ 300 VRMS I-IV Rated mains voltage ≤ 400 VRMS I-III Rated mains voltage < 600 VRMS I-III 3 AMC1200 SBAS542A – APRIL 2011 – REVISED AUGUST 2011 www.ti.com PACKAGE CHARACTERISTICS (1) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT L(I01) Minimum air gap (clearance) Shortest terminal to terminal distance through air L(I02) Minimum external tracking (creepage) Shortest terminal to terminal distance across the package surface CTI Tracking resistance (comparative tracking index) DIN IEC 60112/VDE 0303 part 1 ≥ 175 V Minimum internal gap (internal clearance) Distance through the insulation 0.014 mm RIO Isolation resistance 7 mm 7 mm Input to output, VIO = 500 V, all pins on each side of the barrier tied together to create a two-terminal device, TA < +85°C > 1012 Ω Input to output, VIO = 500 V, +85°C ≤ TA < TA max > 1011 Ω CIO Barrier capacitance input to output VI = 0.5 VPP at 1 MHz 1.2 pF CI Input capacitance to ground VI = 0.5 VPP at 1 MHz 3 pF (1) Creepage and clearance requirements should be applied according to the specific equipment isolation standards of a specific application. Care should be taken to maintain the creepage and clearance distance of the board design to ensure that the mounting pads of the isolator on the printed circuit board (PCB) do not reduce this distance. Creepage and clearance on a PCB become equal according to the measurement techniques shown in the Isolation Glossary section. Techniques such as inserting grooves and/or ribs on the PCB are used to help increase these specifications. ELECTRICAL CHARACTERISTICS All minimum/maximum specifications at TA = –40°C to +105°C and within the specified voltage range, unless otherwise noted. Typical values are at TA = +25°C, VDD1 = 5 V, and VDD2 = 3.3 V. AMC1200 PARAMETER TEST CONDITIONS MIN TYP MAX UNIT INPUT Maximum input voltage before clipping VINP – VINN Differential input voltage VINP – VINN VCM Common-mode operating range VOS Input offset voltage TCVOS Input offset thermal drift ±320 mV –250 +250 -0.16 VDD1 mV V –1.5 ±0.2 +1.5 mV –10 ±1.5 +10 µV/K VIN from 0 V to 5 V at 0 Hz 108 dB 95 dB 3 pF CMRR Common-mode rejection ratio CIN Input capacitance to GND1 CIND Differential input capacitance 3.6 pF RIN Differential input resistance 28 kΩ 60 100 kHz –0.5 ±0.05 +0.5 –1 ±0.05 +1 VIN from 0 V to 5 V at 50 kHz VINP or VINN Small-signal bandwidth OUTPUT Nominal gain GERR Gain error TCGERR Gain error thermal drift Nonlinearity 8 Initial, at TA = +25°C ±56 Output noise PSRR Power-supply rejection ratio Rise/fall time 4 % ppm/K 4.5 V ≤ VDD2 ≤ 5.5 V –0.075 ±0.015 +0.075 2.7 V ≤ VDD2 ≤ 3.6 V –0.1 ±0.023 +0.1 Nonlinearity thermal drift % % % 2.4 ppm/K VINP = VINN = 0 V 3.1 mVRMS vs VDD1, 10-kHz ripple 80 dB vs VDD2, 10-kHz ripple 61 0.5-V step, 10% to 90% 3.66 dB 6.6 µs Copyright © 2011, Texas Instruments Incorporated AMC1200 SBAS542A – APRIL 2011 – REVISED AUGUST 2011 www.ti.com ELECTRICAL CHARACTERISTICS (continued) All minimum/maximum specifications at TA = –40°C to +105°C and within the specified voltage range, unless otherwise noted. Typical values are at TA = +25°C, VDD1 = 5 V, and VDD2 = 3.3 V. AMC1200 PARAMETER TEST CONDITIONS VIN to VOUT signal delay Common-mode transient immunity CMTI TYP MAX 0.5-V step, 50% to 10%, unfiltered output 1.6 3.3 µs 0.5-V step, 50% to 50%, unfiltered output 3.15 5.6 µs 0.5-V step, 50% to 90%, unfiltered output 5.26 9.9 µs VCM = 1 kV Output common-mode voltage ROUT MIN UNIT 10 15 kV/µs 2.7 V ≤ VDD2 ≤ 3.6 V 1.15 1.29 1.45 V 4.5 V ≤ VDD2 ≤ 5.5 V 2.4 2.55 2.7 V Short-circuit current 20 mA Output resistance 2.5 Ω POWER SUPPLY VDD1 High-side supply voltage 4.5 5.0 5.5 VDD2 Low-side supply voltage 2.7 5.0 5.5 IDD1 High-side supply current 5.4 8 mA IDD2 Low-side supply current 3.8 6 mA PDD1 High-side power dissipation PDD2 Low-side power dissipation 2.7 V < VDD2 < 3.6 V 4.5 V < VDD2 < 5.5 V V V 4.4 7 mA 27.0 44.0 mW 2.7 V < VDD2 < 3.6 V 11.4 21.6 mW 4.5 V < VDD2 < 5.5 V 22.0 38.5 mW PIN CONFIGURATION DUB PACKAGE SOP-8 (TOP VIEW) VDD1 1 8 VDD2 VINP 2 7 VOUTP VINN 3 6 VOUTN GND1 4 5 GND2 PIN DESCRIPTIONS PIN # PIN NAME FUNCTION 1 VDD1 Power 2 VINP Analog input Noninverting analog input 3 VINN Analog input Inverting analog input 4 GND1 Power High-side analog ground 5 GND2 Power Low-side analog ground 6 VOUTN Analog output Inverting analog output 7 VOUTP Analog output Noninverting analog output 8 VDD2 Power Copyright © 2011, Texas Instruments Incorporated DESCRIPTION High-side power supply Low-side power supply 5 AMC1200 SBAS542A – APRIL 2011 – REVISED AUGUST 2011 www.ti.com TYPICAL CHARACTERISTICS At VDD1 = VDD2 = 5 V, VINP = –250 mV to +250 mV, and VINN = 0 V, unless otherwise noted. INPUT OFFSET vs HIGH-SIDE SUPPLY VOLTAGE INPUT OFFSET vs LOW-SIDE SUPPLY VOLTAGE 2 2 1.5 1.5 1 1 Input Offset (mV) Input Offset (mV) VDD2 = 2.7 V to 3.6 V 0.5 0 −0.5 0.5 0 −0.5 −1 −1 −1.5 −1.5 −2 4.5 4.75 5 VDD1 (V) 5.25 −2 2.7 5.5 3 3.3 3.6 VDD2 (V) Figure 1. Figure 2. INPUT OFFSET vs LOW-SIDE SUPPLY VOLTAGE INPUT OFFSET vs TEMPERATURE 2 2 1.5 1 1 0.5 0 −0.5 0 −0.5 −1 −1.5 −1.5 4.75 5 VDD2 (V) 5.25 −2 −40 −25 −10 5.5 5 20 35 50 65 Temperature (°C) Figure 3. Figure 4. COMMON-MODE REJECTION RATIO vs INPUT FREQUENCY INPUT CURRENT vs INPUT VOLTAGE 130 40 120 30 110 20 100 90 80 −30 Figure 5. 110 125 −10 60 100 95 0 −20 1 10 Input Frequency (kHz) 80 10 70 50 0.1 6 0.5 −1 −2 4.5 CMRR (dB) Input Offset (mV) 1.5 Input Current (µA) Input Offset (mV) VDD2 = 4.5 V to 5.5 V −40 −400 −300 −200 −100 0 100 Input Voltage (mV) 200 300 400 Figure 6. Copyright © 2011, Texas Instruments Incorporated AMC1200 SBAS542A – APRIL 2011 – REVISED AUGUST 2011 www.ti.com TYPICAL CHARACTERISTICS (continued) At VDD1 = VDD2 = 5 V, VINP = –250 mV to +250 mV, and VINN = 0 V, unless otherwise noted. INPUT BANDWIDTH vs TEMPERATURE GAIN ERROR vs HIGH-SIDE SUPPLY VOLTAGE 120 1 0.8 0.6 0.4 100 Gain Error (%) Input Bandwidth (kHz) 110 90 80 0.2 0 −0.2 −0.4 −0.6 70 −0.8 60 −40 −25 −10 5 20 35 50 65 Temperature (°C) 80 95 −1 4.5 110 125 5.25 Figure 8. GAIN ERROR vs LOW-SIDE SUPPLY VOLTAGE GAIN ERROR vs LOW-SIDE SUPPLY VOLTAGE 0.4 Gain Error (%) 0.6 0.4 0.2 0 −0.2 0.2 0 −0.2 −0.4 −0.4 −0.6 −0.6 −0.8 −0.8 −1 2.7 3 3.3 VDD2 = 4.5 V to 5.5 V 0.8 0.6 −1 4.5 3.6 VDD2 (V) 4.75 5 VDD2 (V) Figure 9. Figure 10. GAIN ERROR vs TEMPERATURE NORMALIZED GAIN vs INPUT FREQUENCY 1 5.25 5.5 10 0 0.6 −10 Normalized Gain (dB) 0.8 0.4 0.2 0 −0.2 −0.4 −20 −30 −40 −50 −0.6 −60 −0.8 −70 −1 −40 −25 −10 5.5 1 VDD2 = 2.7 V to 3.6 V 0.8 Gain Error (%) 5 VDD1 (V) Figure 7. 1 Gain Error (%) 4.75 5 20 35 50 65 Temperature (°C) Figure 11. Copyright © 2011, Texas Instruments Incorporated 80 95 110 125 −80 1 10 100 Input Frequency (kHz) 500 Figure 12. 7 AMC1200 SBAS542A – APRIL 2011 – REVISED AUGUST 2011 www.ti.com TYPICAL CHARACTERISTICS (continued) At VDD1 = VDD2 = 5 V, VINP = –250 mV to +250 mV, and VINN = 0 V, unless otherwise noted. OUTPUT PHASE vs INPUT FREQUENCY OUTPUT VOLTAGE vs INPUT VOLTAGE 0 5 −30 4.5 −60 VOUTP VOUTN 4 Output Voltage (V) Output Phase (°) −90 −120 −150 −180 −210 −240 3.5 3 2.5 2 1.5 −270 1 −300 0.5 −330 −360 1 10 100 Input Frequency (kHz) 0 −400 1000 −200 −100 0 100 Input Voltage (mV) 200 Figure 13. Figure 14. OUTPUT VOLTAGE vs INPUT VOLTAGE NONLINEARITY vs HIGH-SIDE SUPPLY VOLTAGE 3.6 3.3 −300 300 400 0.1 VDD2 = 2.7 V to 3.6 V VOUTP VOUTN 3 0.08 0.06 2.4 Nonlinearity (%) Output Voltage (V) 2.7 2.1 1.8 1.5 1.2 0.04 0.02 0 −0.02 −0.04 0.9 −0.06 0.6 −0.08 0.3 0 −400 −300 −200 −100 0 100 Input Voltage (mV) 200 300 −0.1 4.5 400 NONLINEARITY vs LOW-SIDE SUPPLY VOLTAGE NONLINEARITY vs LOW-SIDE SUPPLY VOLTAGE 5.5 0.1 VDD2 = 2.7 V to 3.6 V 0.06 0.06 0.04 0.04 0.02 0 −0.02 −0.04 0.02 0 −0.02 −0.04 −0.06 −0.06 −0.08 −0.08 3 3.3 3.6 VDD2 = 4.5 V to 5.5 V 0.08 Nonlinearity (%) Nonlinearity (%) 5.25 Figure 16. 0.1 8 5 VDD1 (V) Figure 15. 0.08 −0.1 2.7 4.75 −0.1 4.5 VDD2 (V) 4.75 5 VDD2 (V) Figure 17. Figure 18. 5.25 5.5 Copyright © 2011, Texas Instruments Incorporated AMC1200 SBAS542A – APRIL 2011 – REVISED AUGUST 2011 www.ti.com TYPICAL CHARACTERISTICS (continued) At VDD1 = VDD2 = 5 V, VINP = –250 mV to +250 mV, and VINN = 0 V, unless otherwise noted. NONLINEARITY vs INPUT VOLTAGE NONLINEARITY vs TEMPERATURE 0.1 0.1 VDD2 = 3 V VDD2 = 5 V 0.06 0.06 0.04 0.04 0.02 0 −0.02 −0.04 0.02 0 −0.02 −0.04 −0.06 −0.06 −0.08 −0.08 −0.1 −250 −200 −150 −100 −50 0 50 100 Input Voltage (mV) 150 200 −0.1 −40 −25 −10 250 5 20 35 50 65 Temperature (°C) 80 95 Figure 19. Figure 20. OUTPUT NOISE DENSITY vs FREQUENCY POWER-SUPPLY REJECTION RATIO vs RIPPLE FREQUENCY 2600 100 2400 90 2200 80 2000 70 PSRR (dB) Noise (nV/sqrt(Hz)) 0.08 Nonlinearity (%) Nonlinearity (%) 0.08 1800 1600 1400 50 40 30 1000 20 800 10 1 10 100 VDD1 VDD2 60 1200 600 0.1 110 125 0 1 Frequency (kHz) 10 Ripple Frequency (kHz) Figure 21. Figure 22. OUTPUT RISE/FALL TIME vs TEMPERATURE FULL-SCALE STEP RESPONSE 100 10 Output Rise/Fall Time (µs) 9 8 500 mV/div 7 6 5 4 200 mV/div 3 2 500 mV/div 1 0 −40 −25 −10 5 20 35 50 65 Temperature (°C) Figure 23. Copyright © 2011, Texas Instruments Incorporated 80 95 110 125 Time (2 ms/div) Figure 24. 9 AMC1200 SBAS542A – APRIL 2011 – REVISED AUGUST 2011 www.ti.com TYPICAL CHARACTERISTICS (continued) At VDD1 = VDD2 = 5 V, VINP = –250 mV to +250 mV, and VINN = 0 V, unless otherwise noted. OUTPUT DELAY TIME vs TEMPERATURE OUTPUT COMMON-MODE VOLTAGE vs LOW-SIDE SUPPLY VOLTAGE 10 5 8 Signal Delay (µs) 7 6 5 4 3 2 1 0 −40 −25 −10 5 20 35 50 65 Temperature (°C) 80 95 VDD2 rising VDD2 falling Output Common−Mode Voltage (V) 50% to 10% 50% to 50% 50% to 90% 9 4 3 2 1 0 3.5 110 125 3.7 3.8 3.9 4 4.1 VDD2 (V) 4.2 Figure 25. Figure 26. OUTPUT COMMON-MODE VOLTAGE vs TEMPERATURE SUPPLY CURRENT vs SUPPLY VOLTAGE 5 4.3 4.4 4.5 8 VDD2 = 2.7 V to 3.6 V VDD2 = 4.5 V to 5.5 V Output Common−Mode Voltage (V) 3.6 IDD1 IDD2 7 Supply Current (mA) 4 3 2 6 5 4 3 2 1 1 0 −40 −25 −10 5 20 35 50 65 Temperature (°C) 80 95 0 4.5 110 125 4.75 5 Supply Voltage (V) Figure 27. Figure 28. LOW-SIDE SUPPLY CURRENT vs LOW-SIDE SUPPLY VOLTAGE SUPPLY CURRENT vs TEMPERATURE 8 5.25 5.5 8 7 7 6 6 Supply Current (mA) IDD2 (mA) VDD2 = 2.7 V to 3.6 V 5 4 3 2 1 0 2.7 4 3 2 1 3 3.3 VDD2 (V) Figure 29. 10 5 3.6 0 −40 −25 −10 IDD1 IDD2 5 20 35 50 65 Temperature (°C) 80 95 110 125 Figure 30. Copyright © 2011, Texas Instruments Incorporated AMC1200 SBAS542A – APRIL 2011 – REVISED AUGUST 2011 www.ti.com THEORY OF OPERATION INTRODUCTION The differential analog input of the AMC1200 is a switched-capacitor circuit based on a second-order modulator stage that digitizes the input signal into a 1-bit output stream. The device compares the differential input signal (VIN = VINP – VINN) against the internal reference of 2.5 V using internal capacitors that are continuously charged and discharged with a typical frequency of 10 MHz. With the S1 switches closed, CIND charges to the voltage difference across VINP and VINN. For the discharge phase, both S1 switches open first and then both S2 switches close. CIND discharges to approximately AGND + 0.8V during this phase. Figure 31 shows the simplified equivalent input circuitry. VDD1 GND1 GND1 CINP = 3pF 3pF 400W VINP S1 S2 AGND + 0.8V Equivalent Circuit VINP CIND = 3.6pF S1 400W VINN RIN = 28kW S2 VINN AGND + 0.8V 3pF CINN = 3pF GND1 GND1 RIN = 1 fCLK · CDIFF GND1 (fCLK = 10MHz) Figure 31. Equivalent Input Circuit The analog input range is tailored to directly accommodate a voltage drop across a shunt resistor used for current sensing. However, there are two restrictions on the analog input signals, VINP and VINN. If the input voltage exceeds the range AGND – 0.5 V to AVDD + 0.5 V, the input current must be limited to 10 mA to prevent the implemented input protection diodes from damage. In addition, the linearity and the noise performance of the device are ensured only when the differential analog input voltage remains within ±250 mV. The isolated digital bit stream is processed by a third-order analog filter on the low-side and presented as a differential output of the device. The SiO2-based capacitive isolation barrier supports a high level of magnetic field immunity, as described in application report SLLA181, ISO72x Digital Isolator Magnetic-Field Immunity (available for download at www.ti.com). Copyright © 2011, Texas Instruments Incorporated 11 AMC1200 SBAS542A – APRIL 2011 – REVISED AUGUST 2011 www.ti.com APPLICATION INFORMATION MOTOR CONTROL A typical operation of the AMC1200 in a motor-control application is shown in Figure 32. Measurement of the motor phase current is done through the shunt resistor, RSHUNT (in this case, a two-terminal shunt). For better performance, the differential signal is filtered using RC filters (components R2, R3, and C2). Optionally, C3 and C4 can be used to reduce charge dumping from the inputs. In this case, care should be taken when choosing the quality of these capacitors; mismatch in values of these capacitors leads to a common-mode error at the input of the modulator. HV+ Floating Power Supply Gated Drive Circuit Isolation Barrier TMC320 C/F28xxx R1 AMC1200 VDD1 D1 5.1V C5(1) 0.1mF VINP R3 12W RSHUNT To Load Power Supply VDD2 C1(1) 0.1mF R2 12W VOUTP C2(1) 330pF C3 10pF (optional) ADC C4 10pF (optional) VINN VOUTN GND1 GND2 Gated Drive Circuit HV- (1) Place these capacitors as close as possible to the AMC1200. Figure 32. Typical Application Diagram for the AMC1200 The high-side power supply for the AMC1200 (VDD1) is derived from the power supply of the upper gate driver. For lowest cost, a Zener diode can be used to limit the voltage to 5 V ±10%. A decoupling capacitor of 0.1 µF is recommended for filtering this power-supply path. This capacitor (C1 in Figure 32) should be placed as close as possible to the VDD1 pin for best performance. If better filtering is required, an additional 1-µF to 10-µF capacitor can be used. The floating ground reference (GND1) is derived from the end of the shunt resistor, which is connected to the negative input of the AMC1200 (VINN). If a four-terminal shunt is used, the inputs of AMC1200 are connected to the inner leads, while GND1 is connected to one of the outer leads of the shunt. The high transient immunity of the AMC1200 ensures reliable and accurate operation even in high-noise environments such as the power stages of the motor drives. The differential output of the AMC1200 can either directly drive an analog-to-digital converter (ADC) input or can be further filtered before being processed by the ADC. As shown in Figure 33, it is recommended to place the bypass and filter capacitors as close as possible to the AMC1200 to ensure best performance. 12 Copyright © 2011, Texas Instruments Incorporated AMC1200 SBAS542A – APRIL 2011 – REVISED AUGUST 2011 www.ti.com Top View 12 W SMD 0603 To Shunt 12 W SMD 0603 330 pF SMD 0603 LEGEND Top layer; copper pour and traces VDD1 VDD2 VINP VOUTP 0.1 mF SMD 1206 0.1mF 0.1 mF SMD 1206 AMC1200 VINN VOUTN GND1 GND2 To Filter or ADC SMD 1206 Clearance area. Keep free of any conductive materials. High-side area Controller-side area Via Figure 33. AMC1200 Layout Recommendation To maintain the isolation barrier and the high CMTI of the device, the distance between the high-side ground (GND1) and the low-side ground (GND2) should be kept at maximum; that is, the entire area underneath the device should be kept free of any conducting materials. Copyright © 2011, Texas Instruments Incorporated 13 AMC1200 SBAS542A – APRIL 2011 – REVISED AUGUST 2011 www.ti.com VOLTAGE MEASUREMENT The AMC1200 can also be used for isolated voltage measurement applications, as shown in a simplified way in Figure 34. In such applications, usually a resistor divider (R1 and R2 in Figure 34) is used to match the relatively small input voltage range of the AMC1200. R2 and the input resistance RIN of the AMC1200 also create a resistance divider that results in additional gain error. With the assumption that R1 and RIN have a considerably higher value than R2, the resulting total gain error can be estimated using Equation 1: R GERRTOT = GERR + 2 RIN Where GERR = the gain error of AMC1200. (1) L1 R1 R2 RIN L2 Figure 34. Voltage Measurement Application 14 Copyright © 2011, Texas Instruments Incorporated AMC1200 SBAS542A – APRIL 2011 – REVISED AUGUST 2011 www.ti.com ISOLATION GLOSSARY Creepage Distance: The shortest path between two conductive input to output leads measured along the surface of the insulation. The shortest distance path is found around the end of the package body. Clearance: The shortest distance between two conductive input to output leads measured through air (line of sight). Input-to-Output Barrier Capacitance: The total capacitance between all input terminals connected together, and all output terminals connected together. Input-to-Output Barrier Resistance: The total resistance between all input terminals connected together, and all output terminals connected together. Primary Circuit: An internal circuit directly connected to an external supply mains or other equivalent source that supplies the primary circuit electric power. Secondary Circuit: A circuit with no direct connection to primary power that derives its power from a separate isolated source. Comparative Tracking Index (CTI): CTI is an index used for electrical insulating materials. It is defined as the numerical value of the voltage that causes failure by tracking during standard testing. Tracking is the process that produces a partially conducting path of localized deterioration on or through the surface of an insulating material as a result of the action of electric discharges on or close to an insulation surface. The higher CTI value of the insulating material, the smaller the minimum creepage distance. Generally, insulation breakdown occurs either through the material, over its surface, or both. Surface failure may arise from flashover or from the progressive degradation of the insulation surface by small localized sparks. Such sparks are the result of the breaking of a surface film of conducting contaminant on the insulation. The resulting break in the leakage current produces an overvoltage at the site of the discontinuity, and an electric spark is generated. These sparks often cause carbonization on insulation material and lead to a carbon track between points of different potential. This process is known as tracking. Insulation: Operational insulation—Insulation needed for the correct operation of the equipment. Basic insulation—Insulation to provide basic protection against electric shock. Supplementary insulation—Independent insulation applied in addition to basic insulation in order to ensure protection against electric shock in the event of a failure of the basic insulation. Double insulation—Insulation comprising both basic and supplementary insulation. Reinforced insulation—A single insulation system that provides a degree of protection against electric shock equivalent to double insulation. Copyright © 2011, Texas Instruments Incorporated 15 AMC1200 SBAS542A – APRIL 2011 – REVISED AUGUST 2011 www.ti.com Pollution Degree: Pollution Degree 1—No pollution, or only dry, nonconductive pollution occurs. The pollution has no influence on device performance. Pollution Degree 2—Normally, only nonconductive pollution occurs. However, a temporary conductivity caused by condensation is to be expected. Pollution Degree 3—Conductive pollution, or dry nonconductive pollution that becomes conductive because of condensation, occurs. Condensation is to be expected. Pollution Degree 4—Continuous conductivity occurs as a result of conductive dust, rain, or other wet conditions. Installation Category: Overvoltage Category—This section is directed at insulation coordination by identifying the transient overvoltages that may occur, and by assigning four different levels as indicated in IEC 60664. 1. Signal Level: Special equipment or parts of equipment. 2. Local Level: Portable equipment, etc. 3. Distribution Level: Fixed installation. 4. Primary Supply Level: Overhead lines, cable systems. Each category should be subject to smaller transients than the previous category. 16 Copyright © 2011, Texas Instruments Incorporated AMC1200 SBAS542A – APRIL 2011 – REVISED AUGUST 2011 www.ti.com REVISION HISTORY NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Original (April 2011) to Revision A Page • Changed sign for maximum junction temperature from minus to plus (typo) ....................................................................... 2 • Changed surge immunity parameter from ±4000 to ±6000 .................................................................................................. 3 • Added "0.5-V step" to test condition for Rise/fall time parameter ......................................................................................... 4 • Changed Figure 12 ............................................................................................................................................................... 7 • Changed Figure 13 ............................................................................................................................................................... 8 Copyright © 2011, Texas Instruments Incorporated 17 PACKAGE OPTION ADDENDUM www.ti.com 22-Oct-2011 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) AMC1200SDUB ACTIVE SOP DUB 8 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR AMC1200SDUBR ACTIVE SOP DUB 8 350 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jun-2011 TAPE AND REEL INFORMATION *All dimensions are nominal Device AMC1200SDUBR Package Package Pins Type Drawing SOP DUB 8 SPQ 350 Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 330.0 24.4 Pack Materials-Page 1 10.9 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 10.01 5.85 16.0 24.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jun-2011 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) AMC1200SDUBR SOP DUB 8 350 358.0 335.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP® Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2011, Texas Instruments Incorporated