TI INA149-EP

INA149-EP
www.ti.com
SBOS608A – MARCH 2012 – REVISED APRIL 2012
HIGH COMMON-MODE VOLTAGE DIFFERENCE AMPLIFIER
FEATURES
1
•
•
•
Common-Mode Voltage Range: ±275 V
Minimum CMRR: 84 dB from –55°C to +125°C
DC Specifications:
– Maximum Offset Voltage: 3500 μV
– Maximum Gain Error: 0.047%
– Maximum Gain Nonlinearity: 0.001% FSR at
25°C
AC Performance:
– Bandwidth: 500 kHz
– Typical Slew Rate: 5 V/μs
Wide Supply Range: ±2.0 V to ±18 V
– Maximum Quiescent Current: 1100 μA
– Output Swing on ±15-V Supplies: ±13.5 V
Input Protection:
– Common-Mode: ±500 V
– Differential: ±500 V
SUPPORTS DEFENSE, AEROSPACE,
AND MEDICAL APPLICATIONS
•
•
•
•
•
•
•
120
APPLICATIONS
•
•
•
•
•
High-Voltage Current Sensing
Battery Cell Voltage Monitoring
Power-Supply Current Monitoring
Motor Controls
Replacement for Isolation Circuits
Controlled Baseline
One Assembly/Test Site
One Fabrication Site
Available in Military (–55°C/125°C)
Temperature Range (1)
Extended Product Life Cycle
Extended Product-Change Notification
Product Traceability
Common−Mode Rejection Ratio (dB)
•
•
•
2
100
90
80
70
60
50
40
(1)
INA149
Competitor A
110
10
100
1k
Frequency (Hz)
10k
100k
Additional temperature ranges available - contact factory
DESCRIPTION
The INA149 is a precision unity-gain difference amplifier with a very high input common-mode voltage range. It is
a single, monolithic device that consists of a precision op amp and an integrated thin-film resistor network. The
INA149 can accurately measure small differential voltages in the presence of common-mode signals up to
±275 V. The INA149 inputs are protected from momentary common-mode or differential overloads of up to
500 V.
In many applications, where galvanic isolation in not required, the INA149 can replace isolation amplifiers. This
ability can eliminate costly isolated input side power supplies and the associated ripple, noise, and quiescent
current. The excellent 0.0005% nonlinearity and 500-kHz bandwidth of the INA149 are superior to those of
conventional isolation amplifiers.
The INA149 is pin-compatible with the INA117 and INA148 type high common-mode voltage amplifiers and
offers improved performance over both devices. The INA149 is available in the SOIC-8 package with operation
specified over the military temperature range of –55°C to +125°C.
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2012, Texas Instruments Incorporated
INA149-EP
SBOS608A – MARCH 2012 – REVISED APRIL 2012
www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
PACKAGE/ORDERING INFORMATION (1)
(1)
TA
PACKAGE
ORDERABLE PART
NUMBER
PACKAGE MARKING
VID NUMBER
-55°C to 125°C
SOIC-8 - D
INA149AMDREP
INA149AM
V62/12614-01XE
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or visit the
device product folder at www.ti.com.
ABSOLUTE MAXIMUM RATINGS (1)
Over operating free-air temperature range, unless otherwise noted.
INA149
UNIT
Supply voltage
(V+) – (V–)
40
V
Input voltage range
Continuous
300
V
500
V
Common-mode and differential, 10 s
Maximum Voltage on REFA and REFB
Input current on any input pin (2)
(V–) – 0.3 to (V+) + 0.3
V
10
mA
Output short-circuit current duration
Indefinite
Operating temperature range
–55 to +125
°C
Storage temperature range
–65 to +150
°C
+150
°C
Human body model (HBM)
1500
V
Charged device model (CDM)
1000
V
Machine model (MM)
100
V
Junction temperature
ESD rating
(1)
(2)
2
Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may
degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond
those specified is not implied.
REFA and REFB are diode clamped to the power-supply rails. Signals applied to these pins that can swing more than 0.3 V beyond the
supply rails should be limited to 10 mA or less.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA149-EP
INA149-EP
www.ti.com
SBOS608A – MARCH 2012 – REVISED APRIL 2012
THERMAL INFORMATION
INA149
THERMAL METRIC (1)
D (SOIC)
UNITS
8 PINS
Junction-to-ambient thermal resistance (2)
θJA
(3)
110
θJCtop
Junction-to-case (top) thermal resistance
θJB
Junction-to-board thermal resistance (4)
54
ψJT
Junction-to-top characterization parameter (5)
11
ψJB
Junction-to-board characterization parameter (6)
53
θJCbot
Junction-to-case (bottom) thermal resistance (7)
N/A
(1)
(2)
(3)
(4)
(5)
(6)
(7)
57
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
The junction-to-ambient thermal resistance under natural convection is obtained in a simulation on a JEDEC-standard, high-K board, as
specified in JESD51-7, in an environment described in JESD51-2a.
The junction-to-case (top) thermal resistance is obtained by simulating a cold plate test on the package top. No specific JEDECstandard test exists, but a close description can be found in the ANSI SEMI standard G30-88.
The junction-to-board thermal resistance is obtained by simulating in an environment with a ring cold plate fixture to control the PCB
temperature, as described in JESD51-8.
The junction-to-top characterization parameter, ψJT, estimates the junction temperature of a device in a real system and is extracted
from the simulation data for obtaining θJA, using a procedure described in JESD51-2a (sections 6 and 7).
The junction-to-board characterization parameter, ψJB, estimates the junction temperature of a device in a real system and is extracted
from the simulation data for obtaining θJA , using a procedure described in JESD51-2a (sections 6 and 7).
The junction-to-case (bottom) thermal resistance is obtained by simulating a cold plate test on the exposed (power) pad. No specific
JEDEC standard test exists, but a close description can be found in the ANSI SEMI standard G30-88.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA149-EP
3
INA149-EP
SBOS608A – MARCH 2012 – REVISED APRIL 2012
www.ti.com
ELECTRICAL CHARACTERISTICS: V+ = +15 V and V– = –15 V
At TA = +25°C, RL = 2 kΩ connected to ground, and VCM = REFA = REFB = GND, unless otherwise noted.
INA149
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
±0.047
%FSR
GAIN
Initial
VOUT = ±10.0 V,
Gain error
VOUT = ±10.0 V, TA = –55°C to +125°C
Gain
vs temperature, TA = –55°C to +125°C
1
±0.005
V/V
±1.5
Nonlinearity
ppm/°C
±0.0005
±0.001
%FSR
TA = –55°C to +125°C
350
3500
vs temperature, TA = –55°C to +125°C
2.5
µV/°C
120
dB
Differential
800
kΩ
Common-mode
200
kΩ
OFFSET VOLTAGE
Initial offset
vs supply (PSRR), VS = ±2 V to ±18 V, TA = –55°C
to +125°C
90
µV
INPUT
Impedance
Voltage range
Differential
–13.5
13.5
Common-mode
–275
275
At dc, VCM = ±275 V, TA = –55°C to +125°C
Common-mode rejection
(CMRR)
84
V
V
98
dB
At ac, 500 Hz, VCM = 500 VPP
90
dB
At ac, 1 kHz, VCM = 500 VPP
90
dB
OUTPUT
Voltage range
TA = –55°C to +125°C
–13.5
Short-circuit current
Capacitive load drive
No sustained oscillations
13.5
V
±25
mA
10
nF
OUTPUT NOISE VOLTAGE
0.01 Hz to 10 Hz
10 kHz
20
µVPP
550
nV/√Hz
DYNAMIC RESPONSE
Small-signal bandwidth
Slew rate
VOUT = ±10-V step, TA = –55°C to +125°C
Full-power bandwidth
VOUT = 20 VPP
Settling time
0.01%, VOUT = 10-V step
1.7
500
kHz
5
V/µs
32
kHz
7
µs
POWER SUPPLY
Voltage range
Quiescent current
±18
V
VS = ±18 V, VOUT = 0 V
±2
810
950
µA
vs temperature, TA = –55°C to +125°C
0.95
1.1
mA
TEMPERATURE RANGE
4
Specified
–55
+125
°C
Operating
–55
+125
°C
Storage
–65
+150
°C
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA149-EP
INA149-EP
www.ti.com
SBOS608A – MARCH 2012 – REVISED APRIL 2012
ELECTRICAL CHARACTERISTICS: V+ = 5 V and V– = 0 V
At TA = +25°C, RL = 2 kΩ connected to 2.5 V, and VCM= REFA = REFB = 2.5 V, unless otherwise noted.
INA149
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
GAIN
Initial
VOUT = 1.5 V to 3.5 V
1
Gain error
VOUT = 1.5 V to 3.5 V
±0.005
%FSR
Gain
vs temperature, TA = –55°C to +125°C
±1.5
ppm/°C
±0.0005
%FSR
Nonlinearity
V/V
OFFSET VOLTAGE
350
Initial offset
vs temperature, TA = –55°C to +125°C
µV
3
µV/°C
vs supply (PSRR), VS = 4 V to 5 V
120
dB
Differential
800
kΩ
Common-mode
200
INPUT
Impedance
Common-mode
Common-mode rejection
–20
kΩ
25
V
At dc, VCM = –20 V to 25 V
100
dB
vs temperature, TA = –55°C to +125°C, at dc
100
dB
At ac, 500 Hz, VCM = 49 VPP
100
dB
90
dB
At ac, 1 kHz, VCM = 49 VPP
OUTPUT
Voltage range
1.7
Short-circuit current
Capacitive load drive
No sustained oscillations
3.4
V
±15
mA
10
nF
20
µVPP
550
nV/√Hz
500
kHz
OUTPUT NOISE VOLTAGE
0.01 Hz to 10 Hz
10 kHz
DYNAMIC RESPONSE
Small-signal bandwidth
Slew rate
VOUT = 2 VPP step
Full-power bandwidth
VOUT = 2 VPP
Settling time
0.01%, VOUT = 2 VPP step
5
V/µs
32
kHz
7
µs
POWER SUPPLY
Voltage range
Quiescent current
VS = 5 V
vs temperature, TA = –55°C to +125°C
5
V
810
µA
1
mA
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA149-EP
5
INA149-EP
SBOS608A – MARCH 2012 – REVISED APRIL 2012
www.ti.com
Estimated Life (Hours)
1000000
100000
10000
1000
125
130
135
140
145
150
155
160
165
Continuous T J (°C)
A.
See datasheet for absolute maximum and minimum recommended operating conditions.
B.
Silicon operating life design goal is 10 years at 105°C junction temperature (does not include package interconnect
life).
Figure 1. INA149 Wirebond Life Derating Chart
6
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA149-EP
INA149-EP
www.ti.com
SBOS608A – MARCH 2012 – REVISED APRIL 2012
PIN CONFIGURATION
D PACKAGE
SOIC-8
(TOP VIEW)
20 kΩ
380 kΩ
REFB 1
8
NC
7
V+
6
VOUT
5
REFA
380 kΩ
−IN 2
380 kΩ
+
+IN 3
19 kΩ
V− 4
PIN DESCRIPTIONS
(1)
NAME
NO.
–IN
2
Inverting input
DESCRIPTION
+IN
3
Noninverting input
NC
8
No internal connection
REFA
5
Reference input
REFB
1
Reference input
V–
4
Negative power supply
V+
7
Positive power supply (1)
VOUT
6
Output
In this document, (V+) – (V–) is referred to as VS.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA149-EP
7
INA149-EP
SBOS608A – MARCH 2012 – REVISED APRIL 2012
www.ti.com
TYPICAL CHARACTERISTICS
At TA = +25°C, RL = 2 kΩ connected to ground, and VS = ±15 V, unless otherwise noted.
CMRR vs FREQUENCY
COMMON-MODE REJECTION
6
25°C
4
-40°C
80
60
40
2
0
−2
−4
20
−6
−400
0
10
100
1000
10000
100000
1000000
10000000
−300
−200 −100
0
100
200
Common−Mode Input Voltage (V)
300
400
G066
Figure 2.
Figure 3.
COMMON-MODE OPERATING RANGE
vs POWER-SUPPLY VOLTAGE
TYPICAL GAIN ERROR FOR RL = 10 kΩ
(Curves Offset for Clarity)
400
VS = ±18 V
VS = ±15 V
350
VS = ±12 V
VS = ±10 V
Output Error (2 mV/div)
Common−Mode Operating Range (±V)
Frequency (Hz)
300
250
200
150
100
50
0
0
2
4
6
8
10
12
14
Power−Supply Voltage (±V)
16
18
−20 −16 −12
20
−8
G002
−4
0
4
8
Output Voltage (V)
12
Figure 5.
TYPICAL GAIN ERROR FOR RL = 2 kΩ
(Curves Offset for Clarity)
TYPICAL GAIN ERROR FOR RL = 1 kΩ
(Curves Offset for Clarity)
20
VS = ±12 V
VS = ±10 V
Output Error (2 mV/div)
VS = ±18 V
VS = ±15 V
Output Error (2 mV/div)
VS = ±12 V
VS = ±10 V
16
G003
Figure 4.
VS = ±18 V
VS = ±15 V
−20 −16 −12
−8
−4
0
4
8
Output Voltage (V)
12
16
20
−20 −16 −12
G004
Figure 6.
8
VS = ±18 V
VS = ±15 V
VS = ±10 V
VS = ±5 V
125°C
100
Output Voltage (mV)
Common−Mode Rejection Ratio (dB)
120
−8
−4
0
4
8
Output Voltage (V)
12
16
20
G005
Figure 7.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA149-EP
INA149-EP
www.ti.com
SBOS608A – MARCH 2012 – REVISED APRIL 2012
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, RL = 2 kΩ connected to ground, and VS = ±15 V, unless otherwise noted.
TYPICAL GAIN ERROR FOR LOW SUPPLY VOLTAGES
(Curves Offset for Clarity)
GAIN NONLINEARITY
10
VS = ±5 V
VS = ±5 V
VS = ±5 V
VS = ±2.5 V
6
RL = 10 kΩ
Output Error (2 mV/div)
VS = ±15 V
RL = 10 kΩ
8
Error (ppm)
4
RL = 2 kΩ
RL = 1 kΩ
2
0
−2
−4
−6
−8
RL = 1 kΩ
−5
−4
−3
−2
−1
0
1
2
Output Voltage (V)
3
4
−10
−12 −10 −8
5
−6
−4 −2 0
2
4
Output Voltage (V)
G006
Figure 8.
GAIN NONLINEARITY
VS = ±15 V
RL = 2 kΩ
G014
8
6
6
4
4
Error (ppm)
Error (ppm)
12
GAIN NONLINEARITY
2
0
−2
2
0
−2
−4
−4
−6
−6
−8
−8
−6
−4 −2 0
2
4
Output Voltage (V)
6
8
10
VS = ±15 V
RL = 1 kΩ
−10
−12 −10 −8
12
−6
−4 −2 0
2
4
Output Voltage (V)
G015
Figure 10.
6
8
10
12
G016
Figure 11.
GAIN NONLINEARITY
OUTPUT VOLTAGE vs LOAD CURRENT
20
10
VS = ±12 V
RL = 10 kΩ
8
−45°C
+25°C
+85°C
+130°C
15
Output Voltage (V)
6
4
Error (ppm)
10
10
8
2
0
−2
−4
−6
10
5
0
−5
−10
−15
−8
−10
−12 −10 −8
8
Figure 9.
10
−10
−12 −10 −8
6
−6
−4 −2 0
2
4
Output Voltage (V)
6
8
10
12
−20
0
G062
Figure 12.
5
10
15
20
25
Output Current (mA)
30
35
G017
Figure 13.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA149-EP
9
INA149-EP
SBOS608A – MARCH 2012 – REVISED APRIL 2012
www.ti.com
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, RL = 2 kΩ connected to ground, and VS = ±15 V, unless otherwise noted.
GAIN vs FREQUENCY
NOISE SPECTRAL DENSITY vs FREQUENCY
1000
Noise Spectral Density (nV/ Hz)
20
Gain (dB)
0
−20
−40
25 °C
−40 °C
125 °C
−60
−80
100
1k
10k
100k
Frequency (Hz)
1M
900
800
700
600
500
400
10M
1
10
100
1k
Frequency (Hz)
G010
Figure 14.
Noise (10 µV/div)
Power−Supply Rejection Ratio (dB)
POSITIVE PSRR vs FREQUENCY
10
0
Time (10 s/div)
−40°C
+25°C
+125°C
10
1k
Frequency (Hz)
10k
100k
G009
Figure 17.
NEGATIVE PSRR vs FREQUENCY
MAXIMUM POWER DISSIPATION vs TEMPERATURE
2
−40°C
+25°C
+125°C
10
100
1k
Frequency (Hz)
10k
Maximum Power Dissipation (W)
Power−Supply Rejection Ratio (dB)
100
Figure 16.
100k
1.8
1.6
1.4
1.2
1
0.8
0.6
0.4
0.2
0
−60 −40 −20
G064
Figure 18.
10
G008
120
110
100
90
80
70
60
50
40
30
20
G070
120
110
100
90
80
70
60
50
40
30
20
10
0
100k
Figure 15.
0.01 Hz TO 10 Hz NOISE
−50
−50
10k
0
20 40 60 80 100 120 140 160
Ambient Temperature (°C)
G013
Figure 19.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA149-EP
INA149-EP
www.ti.com
SBOS608A – MARCH 2012 – REVISED APRIL 2012
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, RL = 2 kΩ connected to ground, and VS = ±15 V, unless otherwise noted.
LARGE-SIGNAL STEP RESPONSE
SMALL-SIGNAL STEP RESPONSE
CL = 1000 pF
RL = 2 kΩ
Output Voltage (5 V/div)
Output Voltage (25 mV/div)
CL = 1000 pF
RL = 2 kΩ
Time (4 µs/div)
Time (4 µs/div)
G011
G012
Figure 20.
Figure 21.
−80
−100
0 nF
1 nF
3 nF
5 nF
10 nF
1.2
4
Error Voltage
Output Voltage 2
1
0
0.8
−2
0.6
−4
0.4
−6
0.2
−8
0
−10
−0.2
0
20
40
60
80
Time (µs)
100
−12
Time (5 us/div)
120
G018
G065
Figure 22.
Figure 23.
CMRR HISTOGRAM
20
0
10
18
−0.2
8
−0.4
6
−0.6
4
−0.8
2
−1
0
Error Voltage
−2
Output Voltage
−4
16
14
12
10
8
6
4
2
0
Time (5 us/div)
G063
−30
−27
−24
−21
−18
−15
−12
−9
−6
−3
0
3
6
9
12
15
18
21
24
27
30
−1.4
Percent of Population (~5 kU)
12
Output Voltage (V)
Error Voltage (mV)
SETTLING TIME
0.2
−1.2
Output Voltage (V)
SETTLING TIME
1.4
Error Voltage (mV)
Voltage (mV)
SMALL-SIGNAL RESPONSE vs CAPACITIVE LOAD
140
120
100
80
60
40
20
0
−20
−40
−60
CMRR (µV/V)
Figure 24.
G019
Figure 25.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA149-EP
11
INA149-EP
SBOS608A – MARCH 2012 – REVISED APRIL 2012
www.ti.com
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, RL = 2 kΩ connected to ground, and VS = ±15 V, unless otherwise noted.
OFFSET VOLTAGE HISTOGRAM
DIFFERENTIAL GAIN ERROR HISTOGRAM
12
20
Percent of Population (~5 kU)
Percent of Population (~5 kU)
18
10
8
6
4
2
16
14
12
10
8
6
4
2
0
Offset Voltage (µV)
−20
−18
−16
−14
−12
−10
−8
−6
−4
−2
0
2
4
6
8
10
12
14
16
18
20
−1000
−900
−800
−700
−600
−500
−400
−300
−200
−100
0
100
200
300
400
500
600
700
800
900
1000
0
Differential Gain Error (m%)
G022
Figure 26.
GAIN NONLINEARITY HISTOGRAM
35
35
30
30
Percent of Population (~5 kU)
Percent of Population (~5 kU)
PSRR HISTOGRAM
25
20
15
10
5
25
20
15
10
5
0.10
0.11
0.12
0.13
0.14
0.15
0.16
0.17
0.18
0.19
0.20
0.21
0.22
0.23
0.24
0.25
0.26
0.27
0.28
0.29
0.30
0
−1.50
−1.35
−1.20
−1.05
−0.90
−0.75
−0.60
−0.45
−0.30
−0.15
0.00
0.15
0.30
0.45
0.60
0.75
0.90
1.05
1.20
1.35
1.50
0
PSRR (µV/V)
Nonlinearity Error (m%)
G025
Figure 28.
50
1600
40
1200
30
800
20
CMRR (µV/V)
Offset Voltage (µV)
CMRR vs TEMPERATURE
2000
400
0
−400
10
0
−10
−800
−20
−1200
−30
−1600
−40
−2000
−75 −50 −25
0
G026
Figure 29.
OFFSET VOLTAGE vs TEMPERATURE
25
50
75 100 125 150 175
Temperature (°C)
G027
−50
−75 −50 −25
Figure 30.
12
G024
Figure 27.
0
25
50
75 100 125 150 175
Temperature (°C)
G028
Figure 31.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA149-EP
INA149-EP
www.ti.com
SBOS608A – MARCH 2012 – REVISED APRIL 2012
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, RL = 2 kΩ connected to ground, and VS = ±15 V, unless otherwise noted.
GAIN ERROR vs TEMPERATURE
50
1.6
40
1.2
30
0.8
20
Gain Error (m%)
PSRR (µV/V)
PSRR vs TEMPERATURE
2
0.4
0
−0.4
−0.8
10
0
−10
−20
−1.2
−30
−1.6
−40
−2
−75 −50 −25
0
−50
−75 −50 −25
25
50
75 100 125 150 175
Temperature (°C)
G029
0
Figure 32.
25
50
75 100 125 150 175
Temperature (°C)
G030
Figure 33.
GAIN NONLINEARITY vs TEMPERATURE
SLEW RATE vs TEMPERATURE
8
5
4
7
2
Slew Rate (V/µs)
Linearity Error (m%)
3
1
0
−1
−2
−3
6
5
4
3
−4
−5
−75 −50 −25
0
2
−75
25
50
75 100 125 150 175
Temperature (°C)
G031
−25
25
75
Temperature (°C)
Figure 34.
175
G071
Figure 35.
SLEW RATE vs POWER-SUPPLY VOLTAGE
QUIESCENT CURRENT vs TEMPERAUTRE
5
1200
4
1000
Current (µA)
Slew Rate (V/µs)
125
3
2
800
600
1
Negative Slew Rate
Positive Slew Rate
0
0
5
10
15
20
25
Supply Voltage (V)
30
35
40
400
−75 −50 −25
G038
Figure 36.
0
25
50
75 100 125 150 175
Temperature (°C)
G043
Figure 37.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA149-EP
13
INA149-EP
SBOS608A – MARCH 2012 – REVISED APRIL 2012
www.ti.com
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, RL = 2 kΩ connected to ground, and VS = ±15 V, unless otherwise noted.
FREQUENCY RESPONSE vs CAPACITIVE LOAD
QUIESCENT CURRENT vs SUPPLY VOLTAGE
1200
10
0
1000
Quiescent Current (µA)
VOUT / VIN (dB)
−10
−20
−30
−40
−50
0 nF
1 nF
3 nF
5 nF
10 nF
−60
−70
−80
−90
100
800
600
400
−45°C
+25°C
+85°C
+130°C
200
1k
10k
100k
Frequency (Hz)
1M
0
10M
0
G044
Figure 38.
MAXIMUM OUTPUT VOLTAGE vs FREQUENCY
6
8
10
12
14
Supply Voltage (±V)
16
18
20
G056
OVERLOAD RECOVERY
16
Input
Output
25
12
20
Voltage (V)
Maximum Output Voltage (±V)
4
Figure 39.
30
15
8
4
10
0
5
0
1k
10k
100k
Frequency (Hz)
−4
1M
Time (1 µs/div)
G057
Figure 40.
G058
Figure 41.
OVERLOAD RECOVERY
QUIESCENT CURRENT HISTOGRAM
4
50
Input
Output
Percent of Population (~5 kU)
45
0
Voltage (V)
2
−4
−8
−12
40
35
30
25
20
15
10
5
−16
G067
0.70
0.71
0.72
0.73
0.74
0.75
0.76
0.77
0.78
0.79
0.80
0.81
0.82
0.83
0.84
0.85
0.86
0.87
0.88
0.89
0.90
0
Time (1 µs/div)
Quiescent Current (mA)
Figure 42.
14
G059
Figure 43.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA149-EP
INA149-EP
www.ti.com
SBOS608A – MARCH 2012 – REVISED APRIL 2012
APPLICATION INFORMATION
BASIC INFORMATION
Figure 44 shows the basic connections required for dual-supply operation. Applications with noisy or highimpedance power-supply lines may require decoupling capacitors placed close to the device pins. The output
voltage is equal to the differential input voltage between pins 2 and 3. The common-mode input voltage is
rejected. Figure 45 shows the basic connections required for single-supply operation.
−15 V
100 nF
1 F
15 V
4
1
−IN
2
+IN
3
20 kΩ
30 V
1 F
7
100 nF
4
380 kΩ
1
+
19 kΩ
6
VOUT = (+IN) − (−IN)
−IN
2
+IN
3
5
GND
380 kΩ
380 kΩ
100 nF
380 kΩ
GND
380 kΩ
380 kΩ
20 kΩ
1 F
7
+
19 kΩ
6
5
VOUT = (+IN) – (–IN) + VREF
VREF
Figure 44. Basic Power and Signal Connections for Figure 45. Basic Power and Signal Connections for
Dual-Supply Operation
Single-Supply Operation
TRANSFER FUNCTION
Most applications use the INA149 as a simple unity-gain difference amplifier. The transfer function is given in
Equation 1:
VOUT = (+IN) – (–IN)
(1)
Some applications, however, apply voltages to the reference terminals (REFA and REFB). The complete transfer
function is given in Equation 2:
VOUT = (+IN) – (–IN) + 20 × REFA – 19 × REFB
(2)
COMMON-MODE RANGE
The high common-mode range of the INA149 is achieved by dividing down the input signal with a high precision
resistor divider. This resistor divider brings both the positive input and the negative input within the input range of
the internal operational amplifier. This input range depends on the supply voltage of the INA149.
Both Figure 3 and Figure 4 can be used to determine the maximum common-mode range for a specific supply
voltage. The maximum common-mode range can also be calculated by ensuring that both the positive and the
negative input of the internal amplifier are within 1.5 V of the supply voltage.
In case the voltage at the inputs of the internal amplifier exceeds the supply voltage, the internal ESD diodes
start conducting current. This current must be limited to 10 mA to make sure not to exceed the absolute
maximum ratings for the device.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA149-EP
15
INA149-EP
SBOS608A – MARCH 2012 – REVISED APRIL 2012
www.ti.com
COMMON-MODE REJECTION
Common-mode rejection (CMR) of the INA149 depends on the input resistor network, which is laser-trimmed for
accurate ratio matching. To maintain high CMR, it is important to have low source impedance driving the two
inputs. A 75-Ω resistance in series with pins 2 or 3 decreases the common-mode rejection ratio (CMRR) from
100 dB (typical) to 74 dB.
Resistance in series with the reference pins also degrades CMR. A 4-Ω resistance in series with pins 1 or 5
decreases CMRR from 100 dB to 74 dB.
Most applications do not require trimming. Figure 46 shows an optional circuit that may be used for trimming
offset voltage and common-mode rejection.
−15 V
15 V
4
15 V
1
100 µA
½ REF200
100 Ω
+
−IN
2
+IN
3
20 kΩ
7
380 kΩ
380 kΩ
380 kΩ
+
19 kΩ
(1)
6
VOUT = (+IN) − (−IN)
5
10 kΩ
100 Ω
100 µA
½ REF200
−15 V
(1) The OPA171 (a 36-V, low-power, RRO, general-purpose operational amplifier) can be used for this application.
Figure 46. Offset Voltage Trim Circuit
16
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA149-EP
INA149-EP
www.ti.com
SBOS608A – MARCH 2012 – REVISED APRIL 2012
MEASURING CURRENT
The INA149 can be used to measure a current by sensing the voltage drop across a series resistor, RS.
Figure 47 shows the INA149 used to measure the supply currents of a device under test.
The sense resistor imbalances the input resistor matching of the INA149, thus degrading its CMR. Also, the input
impedance of the INA149 loads RS, causing gain error in the voltage-to-current conversion. Both of these errors
can be easily corrected.
The CMR error can be corrected with the addition of a compensation resistor (RC), equal to the value of RS, as
shown in Figure 47. If RS is less than 5 Ω, degradation in the CMR is negligible and RC can be omitted. If RS is
larger than approximately 1 kΩ, trimming RC may be required to achive greater than 84-dB CMR. This error is
caused by the INA149 input impedance mismatch.
V−
V+
(+275 V max)
+VS
4
1
2
20 kΩ
380 kΩ
RS
3
RC
7
380 kΩ
380 kΩ
+
6
(1)
19 kΩ
IDUT+
V−
Device
Under
Test
1
5
V+
4
20 kΩ
VO = RS × IDUT+
7
380 kΩ
IDUT−
2
380 kΩ
RS
3
RC
380 kΩ
+
6
(1)
19 kΩ
VO = RS × IDUT−
5
−VS
(−275 V max)
Figure 47. Measuring Supply Currents of a Device Under Test
If RS is more than approximately 50 Ω, the gain error is greater than the 0.02% specification of the INA149. This
gain error can be corrected by slightly increasing the value of RS. The corrected value (RS') can be calculated by
RS' = RS × 380 kΩ/(380 kΩ – RS)
(3)
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA149-EP
17
INA149-EP
SBOS608A – MARCH 2012 – REVISED APRIL 2012
www.ti.com
NOISE PERFORMANCE
The wideband noise performane of the INA149 is dominated by the internal resistor network. The thermal or
Johnson noise of these resistors measures approximately 550 nV/√Hz. The internal op amp contributes virtually
no excess noise at frequencies above 100 Hz.
Many applications may be satisfied with less than the full 500-kHz bandwidth of the INA149. In these cases, the
noise can be reduced with a low-pass filter on the output. The two-pole filter shown in Figure 48 limits bandwidth
and reduces noise. Because the INA149 has a 1/f noise corner frequency of approximately 100 Hz, a cutoff
frequency below 100 Hz does not further reduce noise.
Component values for different filter frequencies are shown in Table 1.
V−
V+
4
1
–IN
2
+IN
3
7
20 kΩ
380 kΩ
380 kΩ
C2
+
380 kΩ
19 kΩ
6
R1
R2
+
VOUT = (+IN) – (–IN)
(1)
5
C1
(1) For most applications, the OPA171 can be used as an operational amplifier. For directly driving successive-approximation register (SAR)
data converters, the OPA140 is a good choice.
Figure 48. Output Filter for Noise Reduction
Table 1. Components Values for Different Filter Bandwidths
BUTTERWORTH
LOW-PASS (f–3 dB)
OUTPUT NOISE
(mVPP)
200 kHz
1.8
100 kHz
1.1
11 kΩ
11.3 kΩ
10 kHz
0.35
11 kΩ
11.3 kΩ
1 nF
2 nF
1 kHz
0.11
11 kΩ
11.3 kΩ
10 nF
20 nF
100 Hz
0.05
11 kΩ
11.3 kΩ
0.1 µF
0.2 µF
18
R1
R2
C1
C2
100 pF
200 pF
No filter
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA149-EP
INA149-EP
www.ti.com
SBOS608A – MARCH 2012 – REVISED APRIL 2012
BATTERY CELL VOLTAGE MONITOR
The INA149 can be used to measure the voltages of single cells in a stacked battery pack. Figure 49 shows an
examples for such an application.
(+275 V max)
+VS
2
3
INA149
+
2
3
INA149
+
Repeat
for each
cell
ADS8638
12-bit, 8-Channel,
Bipolar SAR ADC
MSP430
16-Bit Ultra-LowPower Microcontroller
2
3
INA149
+
2
3
INA149
+
−VS
(−275 V max)
Figure 49. Battery Cell Voltage Monitor
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA149-EP
19
PACKAGE OPTION ADDENDUM
www.ti.com
27-Apr-2012
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
(3)
INA149AMDREP
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
V62/12614-01XE
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Samples
(Requires Login)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF INA149-EP :
• Catalog: INA149
NOTE: Qualified Version Definitions:
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
27-Apr-2012
• Catalog - TI's standard catalog product
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
INA149AMDREP
Package Package Pins
Type Drawing
SOIC
D
8
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
2500
330.0
12.4
Pack Materials-Page 1
6.4
B0
(mm)
K0
(mm)
P1
(mm)
5.2
2.1
8.0
W
Pin1
(mm) Quadrant
12.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
INA149AMDREP
SOIC
D
8
2500
367.0
367.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated