TI INA333AIDGKRG4

INA333
www.ti.com ..................................................................................................................................................... SBOS445B – JULY 2008 – REVISED OCTOBER 2008
Micro-Power (50µA), Zerø-Drift, Rail-to-Rail Out
Instrumentation Amplifier
FEATURES
DESCRIPTION
1
•
•
•
•
•
•
•
•
•
•
•
•
2
LOW OFFSET VOLTAGE: 25µV (max), G ≥ 100
LOW DRIFT: 0.1µV/°C, G ≥ 100
LOW NOISE: 50nV/√Hz, G ≥ 100
HIGH CMRR: 100dB (min), G ≥ 10
LOW INPUT BIAS CURRENT: 200pA (max)
SUPPLY RANGE: +1.8V to +5.5V
INPUT VOLTAGE: (V–) +0.1V to (V+) –0.1V
OUTPUT RANGE: (V–) +0.05V to (V+) –0.05V
LOW QUIESCENT CURRENT: 50µA
OPERATING TEMPERATURE: –40°C to +125°C
RFI FILTERED INPUTS
MSOP-8 AND DFN-8 PACKAGES
The INA333 is a low-power, precision instrumentation
amplifier offering excellent accuracy. The versatile
3-op amp design, small size, and low power make it
ideal for a wide range of portable applications.
A single external resistor sets any gain from 1 to
1000. The INA333 is designed to use an
industry-standard gain equation: G = 1 + (100kΩ/RG).
The INA333 provides very low offset voltage (25µV,
G ≥ 100), excellent offset voltage drift (0.1µV/°C,
G ≥ 100), and high common-mode rejection (100dB
at G ≥ 10). It operates with power supplies as low as
1.8V (±0.9V), and quiescent current is only
50µA—ideal for battery-operated systems. Using
autocalibration techniques to ensure excellent
precision over the extended industrial temperature
range, the INA333 also offers exceptionally low noise
density (50nV/√Hz) that extends down to dc.
APPLICATIONS
•
•
•
•
•
•
•
•
•
BRIDGE AMPLIFIERS
ECG AMPLIFIERS
PRESSURE SENSORS
MEDICAL INSTRUMENTATION
PORTABLE INSTRUMENTATION
WEIGH SCALES
THERMOCOUPLE AMPLIFIERS
RTD SENSOR AMPLIFIERS
DATA ACQUISITION
The INA333 is available in both MSOP-8 and DFN-8
surface-mount packages and is specified over the
TA = –40°C to +125°C temperature range.
blank
Sample Request
Click Here
V+
7
VIN-
2
RFI Filtered Inputs
150kW
150kW
A1
1
RFI Filtered Inputs
50kW
6
A3
RG
VOUT
50kW
8
RFI Filtered Inputs
VIN+
3
150kW
150kW
5
A2
REF
RFI Filtered Inputs
INA333
4
V-
G=1+
100kW
RG
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2008, Texas Instruments Incorporated
INA333
SBOS445B – JULY 2008 – REVISED OCTOBER 2008 ..................................................................................................................................................... www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
PACKAGE/ORDERING INFORMATION (1)
PRODUCT
PACKAGE-LEAD
PACKAGE DESIGNATOR
MSOP-8
DGK
I333
DFN-8
DRG
I333A
INA333
(1)
PACKAGE MARKING
For the most current package and ordering information see the Package Option Addendum at the end of this document, or see the TI
web site at www.ti.com.
ABSOLUTE MAXIMUM RATINGS (1)
Supply voltage
Analog input voltage range (2)
INA333
UNIT
+7
V
(V–) – 0.3 to (V+) + 0.3
Output short-circuit (3)
V
Continuous
Operating temperature range, TA
–40 to +150
°C
Storage temperature range, TA
–65 to +150
°C
+150
°C
Human body model (HBM)
4000
V
Charged device model (CDM)
1000
V
Machine model (MM)
200
V
Junction temperature, TJ
ESD rating
(1)
(2)
(3)
Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may
degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond
those specified is not implied.
Input terminals are diode-clamped to the power-supply rails. Input signals that can swing more than 0.3V beyond the supply rails should
be current limited to 10mA or less.
Short-circuit to ground.
PIN CONFIGURATIONS
DGK PACKAGE
MSOP-8
(TOP VIEW)
DRG PACKAGE
DFN-8
(TOP VIEW)
RG
1
8
RG
VIN-
2
7
V+
VIN+
3
6
VOUT
V-
4
5
REF
RG
1
VIN-
2
VIN+
3
V-
4
Exposed
Thermal
Die Pad
on
Underside
8
RG
7
V+
6
VOUT
5
REF
INA333
INA333
2
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): INA333
INA333
www.ti.com ..................................................................................................................................................... SBOS445B – JULY 2008 – REVISED OCTOBER 2008
ELECTRICAL CHARACTERISTICS: VS = +1.8V to +5.5V
Boldface limits apply over the specified temperature range, TA = –40°C to +125°C.
At TA = +25°C, RL = 10kΩ, VREF = VS/2, and G = 1, unless otherwise noted.
INA333
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
±10 ±25/G
±25 ±75/G
µV
±0.1 ±0.5/G
µV/°C
±5 ±15/G
µV/V
INPUT (1)
Offset voltage, RTI (2)
VOSI
vs Temperature
vs Power supply
PSR
1.8V ≤ VS ≤ 5.5V
±1 ±5/G
Long-term stability
See note
Turn-on time to specified VOSI
(3)
See Typical characteristics
Impedance
Differential
ZIN
100 || 3
Common-mode
ZIN
100 || 3
Common-mode voltage range
Common-mode rejection
VCM
VO = 0V
CMR
DC to 60Hz
(V–) + 0.1
GΩ || pF
GΩ || pF
(V+) – 0.1
V
G=1
VCM = (V–) + 0.1V to (V+) – 0.1V
80
90
dB
G = 10
VCM = (V–) + 0.1V to (V+) – 0.1V
100
110
dB
G = 100
VCM = (V–) + 0.1V to (V+) – 0.1V
100
115
dB
G = 1000
VCM = (V–) + 0.1V to (V+) – 0.1V
100
115
dB
INPUT BIAS CURRENT
Input bias current
IB
±70
vs Temperature
Input offset current
±200
See Typical Characteristic curve
IOS
±50
vs Temperature
±200
pA
pA/°C
pA
See Typical Characteristic curve
pA/°C
f = 10Hz
50
nV/√Hz
f = 100Hz
50
nV/√Hz
f = 1kHz
50
nV/√Hz
f = 0.1Hz to 10Hz
1
µVPP
100
fA/√Hz
2
pAPP
INPUT VOLTAGE NOISE
Input voltage noise
Input current noise
eNI
G = 100, RS = 0Ω
iN
f = 10Hz
f = 0.1Hz to 10Hz
GAIN
Gain equation
G
1 + (100kΩ/RG)
Range of gain
Gain error
(1)
(2)
(3)
1
V/V
1000
V/V
VS = 5.5V, (V–) + 100mV ≤ VO ≤ (V+) – 100mV
G=1
±0.01
±0.1
%
G = 10
±0.05
±0.25
%
G = 100
±0.07
±0.25
%
G = 1000
±0.25
±0.5
%
Total VOS, Referred-to-input = (VOSI) + (VOSO/G).
RTI = Referred-to-input.
300-hour life test at +150°C demonstrated randomly distributed variation of approximately 1µV.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): INA333
3
INA333
SBOS445B – JULY 2008 – REVISED OCTOBER 2008 ..................................................................................................................................................... www.ti.com
ELECTRICAL CHARACTERISTICS: VS = +1.8V to +5.5V (continued)
Boldface limits apply over the specified temperature range, TA = –40°C to +125°C.
At TA = +25°C, RL = 10kΩ, VREF = VS/2, and G = 1, unless otherwise noted.
INA333
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
GAIN (continued)
Gain vs Temperature
G=1
±1
±5
ppm/°C
G > 1 (4)
±15
±50
ppm/°C
VS = 5.5V, (V–) + 100mV ≤ VO ≤ (V+) – 100mV
Gain nonlinearity
G = 1 to 1000
RL = 10kΩ
10
ppm
OUTPUT
Output voltage swing from rail (5)
VS = 5.5V, RL = 10kΩ
See note
Capacitive load drive
(5)
50
mV
500
pF
–40, +5
mA
G=1
150
kHz
G = 10
35
kHz
G = 100
3.5
kHz
G = 1000
350
Hz
G=1
0.16
V/µs
G = 100
0.05
V/µs
Short-circuit current
ISC
Continuous to common
FREQUENCY RESPONSE
Bandwidth, –3dB
Slew rate
SR
Settling time to 0.01%
VS = 5V, VO = 4V Step
tS
G=1
VSTEP = 4V
50
µs
G = 100
VSTEP = 4V
400
µs
Settling time to 0.001%
tS
G=1
VSTEP = 4V
60
µs
G = 100
VSTEP = 4V
500
µs
50% overdrive
75
µs
Overload recovery
REFERENCE INPUT
RIN
300
Voltage range
V–
kΩ
V+
V
V
POWER SUPPLY
Voltage range
Single
+1.8
+5.5
Dual
±0.9
±2.75
V
75
µA
80
µA
Quiescent current
IQ
VIN = VS/2
50
vs Temperature
TEMPERATURE RANGE
Specified temperature range
–40
+125
°C
Operating temperature range
–40
+150
°C
Thermal resistance
(4)
(5)
4
θJA
MSOP
100
°C/W
DFN
65
°C/W
Does not include effects of external resistor RG.
See Typical Characteristics curve, Output Voltage Swing vs Output Current (Figure 29).
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): INA333
INA333
www.ti.com ..................................................................................................................................................... SBOS445B – JULY 2008 – REVISED OCTOBER 2008
TYPICAL CHARACTERISTICS
At TA = +25°C, VS = 5V, RL = 10kΩ, VREF = midsupply, and G = 1, unless otherwise noted.
INPUT VOLTAGE OFFSET DRIFT
(–40°C to +125°C)
INPUT OFFSET VOLTAGE
VS = 5.5V
-25.0
-22.5
-20.0
-17.5
-15.0
-12.5
-10.0
-7.5
-5.0
-2.5
0
2.5
5.0
7.5
10.0
12.5
15.0
17.5
20.0
22.5
25.0
-0.10
-0.09
-0.08
-0.07
-0.06
-0.05
-0.04
-0.03
-0.02
-0.01
0
0.01
0.02
0.03
0.04
0.05
0.06
0.07
0.08
0.09
0.10
Population
Population
VS = 5.5V
Input Offset Voltage (mV)
Input Voltage Offset Drift (mV/°C)
Figure 1.
Figure 2.
OUTPUT OFFSET VOLTAGE
OUTPUT VOLTAGE OFFSET DRIFT
(–40°C to +125°C)
VS = 5.5V
-75.0
-67.5
-60.0
-52.5
-45.0
-37.5
-30.0
-22.5
-15.0
-7.5
0
7.5
15.0
22.5
30.0
37.5
45.0
52.5
60.0
67.5
75.0
-0.50
-0.45
-0.40
-0.35
-0.30
-0.25
-0.20
-0.15
-0.10
-0.05
0
0.05
0.10
0.15
0.20
0.25
0.30
0.35
0.40
0.45
0.50
Population
Population
VS = 5.5V
Output Offset Voltage (mV)
Output Voltage Offset Drift (mV/°C)
Figure 3.
Figure 4.
OFFSET VOLTAGE vs COMMON-MODE VOLTAGE
0.1Hz TO 10Hz NOISE
0
Gain = 1
VS = 1.8V
-5
Noise (1mV/div)
VOS (mV)
VS = 5V
-10
-15
-20
-25
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
Time (1s/div)
VCM (V)
Figure 5.
Figure 6.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): INA333
5
INA333
SBOS445B – JULY 2008 – REVISED OCTOBER 2008 ..................................................................................................................................................... www.ti.com
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, VS = 5V, RL = 10kΩ, VREF = midsupply, and G = 1, unless otherwise noted.
0.1Hz TO 10Hz NOISE
SPECTRAL NOISE DENSITY
1000
Noise (0.5mV/div)
1000
Output Noise
100
100
Current Noise
Input Noise
10
10
2
(Input Noise) +
Total Input-Referred Noise =
(Output Noise)
2
G
1
1
0.1
Time (1s/div)
Current Noise Density (fA/ÖHz)
Voltage Noise Density (nV/ÖHz)
Gain = 100
1
10
100
1k
10k
Frequency (Hz)
Figure 7.
Figure 8.
NONLINEARITY ERROR
LARGE SIGNAL RESPONSE
G = 1000
G = 100
G = 10
G=1
0.008
Gain = 1
VS = ±2.75V
Output Voltage (1V/div)
DC Output Nonlinearity Error (%FSR)
0.012
0.004
0
-0.004
-0.008
-0.012
0
0.5
1.0
1.5
2.0
2.5
3.0 3.5
4.0
4.5
5.0
Time (25ms/div)
5.5
VOUT (V)
Figure 9.
Figure 10.
LARGE-SIGNAL STEP RESPONSE
SMALL-SIGNAL STEP RESPONSE
Gain = 1
Output Voltage (1V/div)
Output Voltage (50mV/div)
Gain = 100
6
Time (100ms/div)
Time (10ms/div)
Figure 11.
Figure 12.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): INA333
INA333
www.ti.com ..................................................................................................................................................... SBOS445B – JULY 2008 – REVISED OCTOBER 2008
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, VS = 5V, RL = 10kΩ, VREF = midsupply, and G = 1, unless otherwise noted.
SMALL-SIGNAL STEP RESPONSE
SETTLING TIME vs GAIN
10000
Output Voltage (50mV/div)
Gain = 100
Time (ms)
1000
0.001%
100
0.01%
0.1%
10
Time (100ms/div)
1
1000
100
10
Gain (V/V)
Figure 13.
Figure 14.
STARTUP SETTLING TIME
GAIN vs FREQUENCY
80
Gain = 1
G = 1000
Supply
60
40
Gain (dB)
Supply (1V/div)
VOUT (50mV/div)
VOUT
G = 100
G = 10
20
G=1
0
-20
-40
-60
Time (50ms/div)
10
100
10k
1k
100k
1M
Frequency (Hz)
Figure 15.
Figure 16.
COMMON-MODE REJECTION RATIO
COMMON-MODE REJECTION RATIO vs TEMPERATURE
10
VS = 5.5V
VS = ±2.75V
8
G=1
VS = ±0.9V
Population
CMRR (mV/V)
6
4
G = 10
2
0
-2
-4
G = 100,
G = 1000
-6
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
10
20
30
40
50
60
70
80
90
100
-8
-10
-50
CMRR (mV/V)
Figure 17.
-25
0
25
50
75
100
125
150
Temperature (°C)
Figure 18.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): INA333
7
INA333
SBOS445B – JULY 2008 – REVISED OCTOBER 2008 ..................................................................................................................................................... www.ti.com
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, VS = 5V, RL = 10kΩ, VREF = midsupply, and G = 1, unless otherwise noted.
COMMON-MODE REJECTION RATIO vs FREQUENCY
140
2.0
Common-Mode Voltage (V)
2.5
G = 1000
120
CMRR (dB)
TYPICAL COMMON-MODE RANGE vs OUTPUT VOLTAGE
160
G = 100
100
80
60
G=1
40
G = 10
20
1.0
All Gains
0
-1.0
-2.0
2.5
-2.5 -2.0
0
10
100k
10k
1k
100
0
-1.0
2.0
1.0
2.5
Frequency (Hz)
Output Voltage (V)
Figure 19.
Figure 20.
TYPICAL COMMON-MODE RANGE vs OUTPUT VOLTAGE
TYPICAL COMMON-MODE RANGE vs OUTPUT VOLTAGE
5
0.9
VS = +5V
VREF = 0
VS = ±0.9V
VREF = 0
0.7
Common-Mode Voltage (V)
Common-Mode Voltage (V)
VS = ±2.5V
VREF = 0
4
3
All Gains
2
1
0.5
0.3
0.1
All Gains
-0.1
-0.3
-0.5
-0.7
-0.9
-0.9
0
0
3
2
1
5
4
-0.3
0.1
-0.1
0.3
Figure 21.
Figure 22.
1.8
0.5
0.7
0.9
POSITIVE POWER-SUPPLY REJECTION RATIO
160
VS = +1.8V
VREF = 0
1.6
140
1.4
G = 1000
120
1.2
1.0
+PSRR (dB)
Common-Mode Voltage (V)
-0.5
Output Voltage (V)
TYPICAL COMMON-MODE RANGE vs OUTPUT VOLTAGE
All Gains
0.8
0.6
100
G = 100
80
60
G = 10
40
0.4
G=1
20
0.2
0
0
0
8
-0.7
Output Voltage (V)
0.2
0.4
0.5
0.8
1.0
1.2
1.4
1.6
1.8
1
10
100
1k
Output Voltage (V)
Frequency (Hz)
Figure 23.
Figure 24.
Submit Documentation Feedback
10k
100k
1M
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): INA333
INA333
www.ti.com ..................................................................................................................................................... SBOS445B – JULY 2008 – REVISED OCTOBER 2008
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, VS = 5V, RL = 10kΩ, VREF = midsupply, and G = 1, unless otherwise noted.
NEGATIVE POWER-SUPPLY REJECTION RATIO
160
140
G = 1000
-IB
800
100
600
IB (pA)
80
+IB
1000
G = 100
120
-PSRR (dB)
INPUT BIAS CURRENT vs TEMPERATURE
1200
VS = 5V
G = 10
60
400
VS = ±0.9V
40
VS = ±2.75V
200
G=1
20
0
0
-20
-200
0.1
10
1
100
1k
10k
100k
1M
-50
25
0
-25
Frequency (Hz)
75
50
100
125
150
Temperature (°C)
Figure 25.
Figure 26.
| INPUT BIAS CURRENT | vs COMMON-MODE VOLTAGE
INPUT OFFSET CURRENT vs TEMPERATURE
200
250
180
200
160
150
120
IOS (pA)
| IB | (pA)
140
100
80
60
100
VS = ±2.75V
50
0
VS = 5V
40
VS = ±0.9V
-50
20
VS = 1.8V
0
0
0.5
1.0
1.5
2.0
-100
2.5
3.0
3.5
4.0
4.5
5.0
-50
0
25
75
50
Temperature (°C)
Figure 27.
Figure 28.
OUTPUT VOLTAGE SWING vs OUTPUT CURRENT
100
125
150
QUIESCENT CURRENT vs TEMPERATURE
80
(V+)
(V+) - 0.25
(V+) - 0.50
(V+) - 0.75
(V+) - 1.00
(V+) - 1.25
(V+) - 1.50
(V+) - 1.75
VS = ±2.75V
70
VS = ±0.9V
VS = 5V
60
50
IQ (mA)
VOUT (V)
-25
VCM (V)
(V-) + 1.75
(V-) + 1.50
(V-) + 1.25
(V-) + 1.00
(V-) + 0.75
(V-) + 0.50
(V-) + 0.25
(V-)
40
VS = 1.8V
30
20
+125°C
+25°C
-40°C
0
10
20
30
40
50
10
0
60
-50
-25
0
25
50
75
100
125
150
Temperature (°C)
IOUT (mA)
Figure 29.
Figure 30.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): INA333
9
INA333
SBOS445B – JULY 2008 – REVISED OCTOBER 2008 ..................................................................................................................................................... www.ti.com
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, VS = 5V, RL = 10kΩ, VREF = midsupply, and G = 1, unless otherwise noted.
QUIESCENT CURRENT vs COMMON-MODE VOLTAGE
80
70
VS = 5V
60
IQ (mA)
50
40
VS = 1.8V
30
20
10
0
0
1.0
3.0
2.0
4.0
5.0
VCM (V)
Figure 31.
10
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): INA333
INA333
www.ti.com ..................................................................................................................................................... SBOS445B – JULY 2008 – REVISED OCTOBER 2008
APPLICATION INFORMATION
Figure 32 shows the basic connections required for
operation of the INA333. Good layout practice
mandates the use of bypass capacitors placed close
to the device pins as shown.
Table 1 lists several commonly-used gains and
resistor values. The 100kΩ term in Equation 1 comes
from the sum of the two internal feedback resistors of
A1 and A2. These on-chip resistors are laser trimmed
to accurate absolute values. The accuracy and
temperature coefficient of these resistors are included
in the gain accuracy and drift specifications of the
INA333.
The output of the INA333 is referred to the output
reference (REF) terminal, which is normally
grounded. This connection must be low-impedance to
assure good common-mode rejection. Although 15Ω
or less of stray resistance can be tolerated while
maintaining specified CMRR, small stray resistances
of tens of ohms in series with the REF pin can cause
noticeable degradation in CMRR.
The stability and temperature drift of the external gain
setting resistor, RG, also affects gain. The contribution
of RG to gain accuracy and drift can be directly
inferred from the gain Equation 1. Low resistor values
required for high gain can make wiring resistance
important. Sockets add to the wiring resistance and
contribute additional gain error (possibly an unstable
gain error) in gains of approximately 100 or greater.
To ensure stability, avoid parasitic capacitance of
more than a few picofarads at the RG connections.
Careful matching of any parasitics on both RG pins
maintains optimal CMRR over frequency.
SETTING THE GAIN
Gain of the INA333 is set by a single external
resistor, RG, connected between pins 1 and 8. The
value of RG is selected according to Equation 1:
G = 1 + (100kΩ/RG)
(1)
V+
0.1mF
7
VIN-
2
RFI Filter
150kW
150kW
A1
VO = G ´ (VIN+ - VIN-)
RFI Filter
1
50kW
RG
G=1+
6
A3
50kW
+
8
Load VO
RFI Filter
VIN+
100kW
RG
150kW
150kW
A2
3
-
5
Ref
RFI Filter
INA333
4
0.1mF
V-
Also drawn in simplified form:
VINRG
VIN+
VO
INA333
Ref
Figure 32. Basic Connections
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): INA333
11
INA333
SBOS445B – JULY 2008 – REVISED OCTOBER 2008 ..................................................................................................................................................... www.ti.com
Table 1. Commonly-Used Gains and Resistor Values
DESIRED GAIN
(1)
RG (Ω)
NEAREST 1% RG (Ω)
(1)
1
NC
2
100k
100k
NC
5
25k
24.9k
10
11.1k
11k
20
5.26k
5.23k
50
2.04k
2.05
100
1.01k
1k
200
502.5
499
500
200.4
200
1000
100.1
100
NC denotes no connection. When using the SPICE model, the simulation will not converge unless a resistor is connected to the RG pins;
use a very large resistor value.
INTERNAL OFFSET CORRECTION
NOISE PERFORMANCE
The INA333 internal op amps use an auto-calibration
technique with a time-continuous 350kHz op amp in
the signal path. The amplifier is zero-corrected every
8µs using a proprietary technique. Upon power-up,
the amplifier requires approximately 100µs to achieve
specified VOS accuracy. This design has no aliasing
or flicker noise.
The auto-calibration technique used by the INA333
results in reduced low frequency noise, typically only
50nV/√Hz, (G = 100). The spectral noise density can
be seen in detail in Figure 8. Low frequency noise of
the INA333 is approximately 1µVPP measured from
0.1Hz to 10Hz, (G = 100).
OFFSET TRIMMING
The input impedance of the INA333 is extremely
high—approximately 100GΩ. However, a path must
be provided for the input bias current of both inputs.
This input bias current is typically ±70pA. High input
impedance means that this input bias current
changes very little with varying input voltage.
Most applications require no external offset
adjustment; however, if necessary, adjustments can
be made by applying a voltage to the REF terminal.
Figure 33 shows an optional circuit for trimming the
output offset voltage. The voltage applied to REF
terminal is summed at the output. The op amp buffer
provides low impedance at the REF terminal to
preserve good common-mode rejection.
VIN-
V+
RG
VIN+
VO
INA333
100mA
1/2 REF200
Ref
100W
OPA333
±10mV
Adjustment Range
10kW
INPUT BIAS CURRENT RETURN PATH
Input circuitry must provide a path for this input bias
current for proper operation. Figure 34 illustrates
various provisions for an input bias current path.
Without a bias current path, the inputs will float to a
potential that exceeds the common-mode range of
the INA333, and the input amplifiers will saturate. If
the differential source resistance is low, the bias
current return path can be connected to one input
(see the thermocouple example in Figure 34). With
higher source impedance, using two equal resistors
provides a balanced input with possible advantages
of lower input offset voltage as a result of bias current
and better high-frequency common-mode rejection.
100W
100mA
1/2 REF200
V-
Figure 33. Optional Trimming of Output Offset
Voltage
12
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): INA333
INA333
www.ti.com ..................................................................................................................................................... SBOS445B – JULY 2008 – REVISED OCTOBER 2008
OPERATING VOLTAGE
Microphone,
Hydrophone,
etc.
The INA333 operates over a power-supply range of
+1.8V to +5.5V (±0.9V to ±2.75V). Supply voltages
higher than +7V (absolute maximum) can
permanently damage the device. Parameters that
vary over supply voltage or temperature are shown in
the Typical Characteristics section of this data sheet.
INA333
47kW
47kW
LOW VOLTAGE OPERATION
Thermocouple
The INA333 can be operated on power supplies as
low as ±0.9V. Most parameters vary only slightly
throughout this supply voltage range—see the Typical
Characteristics section. Operation at very low supply
voltage requires careful attention to assure that the
input voltages remain within the linear range. Voltage
swing requirements of internal nodes limit the input
common-mode range with low power-supply voltage.
The
Typical
Characteristic
curves
Typical
Common-Mode Range vs Output Voltage (Figure 20
to Figure 23) show the range of linear operation for
various supply voltages and gains.
INA333
10kW
INA333
SINGLE-SUPPLY OPERATION
Center tap provides
bias current return.
Figure 34. Providing an Input Common-Mode
Current Path
INPUT COMMON-MODE RANGE
The linear input voltage range of the input circuitry of
the INA333 is from approximately 0.1V below the
positive supply voltage to 0.1V above the negative
supply. As a differential input voltage causes the
output voltage to increase, however, the linear input
range is limited by the output voltage swing of
amplifiers A1 and A2. Thus, the linear common-mode
input range is related to the output voltage of the
complete amplifier. This behavior also depends on
supply voltage—see Typical Characteristic curves
Typical Common-Mode Range vs Output Voltage
(Figure 20 to Figure 23).
Input overload conditions can produce an output
voltage that appears normal. For example, if an input
overload condition drives both input amplifiers to the
respective positive output swing limit, the difference
voltage measured by the output amplifier is near
zero. The output of the INA333 is near 0V even
though both inputs are overloaded.
The INA333 can be used on single power supplies of
+1.8V to +5.5V. Figure 35 illustrates a basic
single-supply circuit. The output REF terminal is
connected to mid-supply. Zero differential input
voltage demands an output voltage of mid-supply.
Actual output voltage swing is limited to
approximately 50mV above ground, when the load is
referred to ground as shown. The typical
characteristic curve Output Voltage Swing vs Output
Current (Figure 29) shows how the output voltage
swing varies with output current.
With single-supply operation, VIN+ and VIN– must both
be 0.1V above ground for linear operation. For
instance, the inverting input cannot be connected to
ground to measure a voltage connected to the
noninverting input.
To illustrate the issues affecting low voltage
operation, consider the circuit in Figure 35. It shows
the INA333 operating from a single 3V supply. A
resistor in series with the low side of the bridge
assures that the bridge output voltage is within the
common-mode range of the amplifier inputs.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): INA333
13
INA333
SBOS445B – JULY 2008 – REVISED OCTOBER 2008 ..................................................................................................................................................... www.ti.com
+3V
GENERAL LAYOUT GUIDELINES
3V
Attention to good layout practices is always
recommended. Keep traces short and, when
possible, use a printed circuit board (PCB) ground
plane with surface-mount components placed as
close to the device pins as possible. Place a 0.1µF
bypass capacitor closely across the supply pins.
These guidelines should be applied throughout the
analog circuit to improve performance and provide
benefits
such
as
reducing
the
electromagnetic-interference (EMI) susceptibility.
2V - DV
RG
300W
VO
INA333
Ref
2V + DV
1.5V
150W
(1)
R1
(1) R1 creates proper common-mode voltage, only for low-voltage
operation—see the Single-Supply Operation section.
Figure 35. Single-Supply Bridge Amplifier
INPUT PROTECTION
The input terminals of the INA333 are protected with
internal diodes connected to the power-supply rails.
These diodes clamp the applied signal to prevent it
from damaging the input circuitry. If the input signal
voltage can exceed the power supplies by more than
0.3V, the input signal current should be limited to less
than 10mA to protect the internal clamp diodes. This
current limiting can generally be done with a series
input resistor. Some signal sources are inherently
current-limited and do not require limiting resistors.
Instrumentation amplifiers vary in the susceptibility to
radio-frequency interference (RFI). RFI can generally
be identified as a variation in offset voltage or dc
signal levels with changes in the interfering RF signal.
The INA333 has been specifically designed to
minimize susceptibility to RFI by incorporating
passive RC filters with an 8MHz corner frequency at
the VIN+ and VIN– inputs. As a result, the INA333
demonstrates remarkably low sensitivity compared to
previous generation devices. Strong RF fields may
continue to cause varying offset levels, however, and
may require additional shielding.
APPLICATION IDEAS
Additional application ideas are shown in Figure 36 to
Figure 39.
2.8kW
LA
RA
RG/2
INA333
VO
Ref
2.8kW
G = 10
390kW
1/2
OPA2333
RL
1/2
OPA2333
10kW
390kW
Figure 36. ECG Amplifier With Right-Leg Drive
14
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): INA333
INA333
www.ti.com ..................................................................................................................................................... SBOS445B – JULY 2008 – REVISED OCTOBER 2008
+VS
R1
100kW
fLPF = 150Hz
C4
1.06nF
1/2
OPA2333
RA
+VS
R2
100kW
+VS
2
R6
100kW
1/2
OPA2333
7
1
RG
R8
100kW
+VS
3
dc
R3
100kW
4
5
ac
1/2
OPA2333
R12
5kW
+VS
VOUT
OPA333
C3
1m F
R13
318kW
GOPA = 200
+VS
1/2
OPA2333
Wilson
LA
GINA = 5
6
INA333
8
LL
R14
1MW
GTOT = 1kV/V
R7
100kW
VCENTRAL
C1
47pF
(RA + LA + LL)/3
fHPF = 0.5Hz
(provides ac signal coupling)
1/2 VS
R5
390kW
+VS
R4
100kW
R9
20kW
1/2
OPA2333
RL
Inverted
VCM
+VS
VS = +2.7V to +5.5V
1/2
OPA2333
BW = 0.5Hz to 150Hz
+VS
R10
1MW
1/2 VS
C2
0.64mF
R11
1MW
fO = 0.5Hz
Figure 37. Single-Supply, Very Low Power, ECG Circuit
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): INA333
15
INA333
SBOS445B – JULY 2008 – REVISED OCTOBER 2008 ..................................................................................................................................................... www.ti.com
TINA-TI
(FREE DOWNLOAD SOFTWARE)
Virtual instruments offer users the ability to select
input waveforms and probe circuit nodes, voltages,
and waveforms, creating a dynamic quick-start tool.
Using TINA-TI SPICE-Based Analog Simulation
Program with the INA333
Figure 38 and Figure 39 show example TINA-TI
circuits for the INA333 that can be used to develop,
modify, and assess the circuit design for specific
applications. Links to download these simulation files
are given below.
TINA is a simple, powerful, and easy-to-use circuit
simulation program based on a SPICE engine.
TINA-TI is a free, fully functional version of the TINA
software, preloaded with a library of macromodels in
addition to a range of both passive and active
models. It provides all the conventional dc, transient,
and frequency domain analysis of SPICE as well as
additional design capabilities.
NOTE: these files require that either the TINA
software (from DesignSoft) or TINA-TI software be
installed. Download the free TINA-TI software from
the TINA-TI folder.
Available as a free download from the Analog eLab
Design
Center,
TINA-TI
offers
extensive
post-processing capability that allows users to format
results in a variety of ways.
VoA1
1/2 of matched
monolithic dual
NPN transistors
(example: MMDT3904)
RELATED PRODUCTS
For monolithic logarithmic amplifiers (such as LOG112 or LOG114) see the link in footnote 1.
Vout
VM1
8
3
6
+
5
+
7
VCC
VCC
Ref
RG V+
U5 OPA369
Vdiff
Vref+
1/2 of matched
monolithic dual
NPN transistors
(example: MMDT3904)
-
R8 10k
Out
+
U1 OPA335
VCC
4
5
1
U1 INA333
Optional buffer for driving
SAR converters with
sampling systems of ³ 33kHz.
VCC
V
4
RG V-
C1 1n
+
Vref+
Vref+
Input I 10n
+
+
_
Vref+
2
1
R3 14k
2
3
VoA2
3
Vref+
uC Vref/2 2.5
1
+
uC Vref/2 2.5
2
+
4
5
V1 5
NOTE: Temperature compensation
of logging transistors is not shown.
U6 OPA369
VCC
Rset 2.5M
(1) The following link launches the TI logarithmic amplifiers web page: Logarithmic Amplifier Products Home Page
Figure 38. Low-Power Log Function Circuit for Portable Battery-Powered Systems
(Example Glucose Meter)
To download a compressed file that contains the TINA-TI simulation file for this circuit, click the following link:
Log Circuit.
16
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): INA333
INA333
www.ti.com ..................................................................................................................................................... SBOS445B – JULY 2008 – REVISED OCTOBER 2008
3V
R1
2kW
RWa
3W
EMU21 RTD3
-
Pt100 RTD
VT+
U2
OPA333
RWb
3W
+
RTD+
VT 25
+
2 _
3V
VT-
RTD-
Mon+
RGAIN
100kW
Mon-
+
U1 INA333
VDIFF
Out
Ref
8
RG V+
RWc
4W
Temp (°C)
(Volts = °C)
1
4
RG V-
RZERO
100W
3
PGA112
MSP430
6
5
+
7
V
VREF+
3V
VRTD
RWd
3W
RTD Resistance
(Volts = Ohms)
+
+
A
IREF1
A
IREF2
3V
U1 REF3212
VREF
3V
VREF
VREF
Use BF861A
EN
+
In
OUTS
GNDF GNDS
C7
470nF
S
OUTF
+
T3 BF256A
OPA3331 OPA333
Use BF861A
3V
T1 BF256A
+
+
U3
OPA333
3V
-
G
-
V4 3
RSET1
2.5kW
RSET2
2.5kW
RWa, RWb, RWc, and RWd simulate wire resistance. These resistors are included to show the four-wire sense technique immunity to line
mismatches. This method assumes the use of a four-wire RTD.
Figure 39. Four-Wire, 3V Conditioner for a PT100 RTD With Programmable Gain Acquisition System
To download a compressed file that contains the TINA-TI simulation file for this circuit, click the following link:
PT100 RTD.
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): INA333
17
PACKAGE OPTION ADDENDUM
www.ti.com
8-Jun-2009
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
INA333AIDGKR
ACTIVE
MSOP
DGK
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
INA333AIDGKRG4
ACTIVE
MSOP
DGK
8
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
INA333AIDGKT
ACTIVE
MSOP
DGK
8
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
INA333AIDGKTG4
ACTIVE
MSOP
DGK
8
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
INA333AIDRGR
ACTIVE
SON
DRG
8
1000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
INA333AIDRGT
ACTIVE
SON
DRG
8
250
CU NIPDAU
Level-2-260C-1 YEAR
Green (RoHS &
no Sb/Br)
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
10-Jun-2009
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
INA333AIDGKR
MSOP
DGK
8
INA333AIDGKT
INA333AIDRGR
MSOP
DGK
SON
DRG
SPQ
Reel
Reel
Diameter Width
(mm) W1 (mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
W
Pin1
(mm) Quadrant
2500
330.0
12.4
5.3
3.3
1.3
8.0
12.0
Q1
8
250
180.0
12.4
5.3
3.3
1.3
8.0
12.0
Q1
8
1000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
10-Jun-2009
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
INA333AIDGKR
MSOP
DGK
8
2500
370.0
355.0
55.0
INA333AIDGKT
MSOP
DGK
8
250
195.0
200.0
45.0
INA333AIDRGR
SON
DRG
8
1000
346.0
346.0
29.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DLP® Products
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2009, Texas Instruments Incorporated