XR T111 XTR111 SBOS375C – NOVEMBER 2006 – REVISED JUNE 2011 www.ti.com Precision Voltage-to-Current Converter/Transmitter Check for Samples: XTR111 FEATURES DESCRIPTION • The XTR111 is a precision voltage-to-current converter designed for the standard 0mA–20mA or 4mA–20mA analog signals, and can source up to 36mA. The ratio between input voltage and output current is set by the single resistor RSET. The circuit can also be modified for voltage output. 1 2 • • • • • • • • EASY-TO-DESIGN INPUT/OUTPUT RANGES: 0mA–20mA, 4mA–20mA, 5mA–25mA AND VOLTAGE OUTPUTS NONLINEARITY: 0.002% LOW OFFSET DRIFT: 1μV/°C ACCURACY: 0.015% SINGLE-SUPPLY OPERATION WIDE SUPPLY RANGE: 7V to 44V OUTPUT ERROR FLAG (EF) OUTPUT DISABLE (OD) ADJUSTABLE VOLTAGE REGULATOR: 3V to 15V APPLICATIONS • • • • UNIVERSAL VOLTAGE-CONTROLLED CURRENT SOURCE CURRENT OR VOLTAGE OUTPUT FOR 3-WIRE SENSOR SYSTEMS PLC OUTPUT PROGRAMMABLE DRIVER CURRENT-MODE SENSOR EXCITATION An external P-MOSFET transistor ensures high output resistance and a broad compliance voltage range that extends from 2V below the supply voltage, VVSP, to voltages well below GND. The adjustable 3V to 15V sub-regulator output provides the supply voltage for additional circuitry. The XTR111 is available in MSOP and DFN surface-mount packages. 24V 1 VSP XTR111 REGF Regulator Out I- Mirror 5 OD EF IS 9 8 Output Disable Output Failure 2 REGS 4 15W (1) S Q2 VG 3V 3 Q1 G D ISET Signal Input 15W 6 10nF VIN Load GND 10 0mA to 20mA 4mA to 20mA (± Load Ground) SET 7 RSET IOUT = 10 VIN (RVSET ) IOUT = 10 · ISET NOTE: (1) See Application Information, External Current Limit Circuits for other options. 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2006–2011, Texas Instruments Incorporated XTR111 SBOS375C – NOVEMBER 2006 – REVISED JUNE 2011 www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. ORDERING INFORMATION (1) PRODUCT XTR111 (1) PACKAGE-LEAD PACKAGE DESIGNATOR PACKAGE MARKING DFN-10 DRC BSV MSOP-10 DGQ CCM For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the device product folder at www.ti.com. ABSOLUTE MAXIMUM RATINGS (1) (2) Over operating free-air temperature range (unless otherwise noted) XTR111 UNIT +44 V –0.5 to +14 V (VVSP) – 5.5 to (VVSP) + 0.5 V Voltage at REGS, REGF, VIN, OD, EF –0.5 to (VVSP) + 0.5 V Voltage at REGF, VG –0.5 to (VVSP) + 0.5 V ±25 mA Power Supply Voltage, VVSP Voltage at SET (3) Voltage at IS (3) (4) Current into any pin (3) (4) (5) Output Short-Circuit Duration (6): VG Continous to common and VVSP REGF Continous to common and VVSP Operating Temperature –55 to +125 °C Storage Temperature –65 to +150 °C 2000 V Electrostatic Discharge Rating (HBM) (1) (2) (3) (4) (5) (6) 2 Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those specified is not supported. Refer to the Package Option Addendum at the end of this document for lead temperature ratings. Input terminals are diode-clamped to the power-supply rails. Input signals that can swing more than 0.5V beyond the supply rails must be current limited. The IS pin current absolute maximum rating is +25mA and –50mA. See the following sections Explanation of Pin Functions, External MOSFET, and Voltage Regulator in Application Information regarding safe voltage ranges and currents. See text in Application Information regarding safe voltage ranges and currents. Copyright © 2006–2011, Texas Instruments Incorporated XTR111 SBOS375C – NOVEMBER 2006 – REVISED JUNE 2011 www.ti.com ELECTRICAL CHARACTERISTICS Boldface limits apply over the specified temperature range: TA = –40°C to +85°C. All specifications at TA = +25°C, VVSP = +24V, RSET = 2.0kΩ, REGF connected to REGS; OD = Low, External FET connected, unless otherwise noted. XTR111 PARAMETER CONDITIONS MIN Specified Performance (1) 0.1 TYP MAX UNIT TRANSMITTER IOUT = 10 × VVIN/RSET Transfer Function Specified Output Current IOUT Derated Performance (2) (2) (3) Offset Current IOS Span Error, IOUT/ISET vs Temperature (2) 0.002 0.1mA to 36mA 0.004 IOUT = 4mA (1) 0.002 0.02 % of Span Input Offset Voltage (2) 0.001 % of Span/°C 0.005 % of Span/V 0.1mA to 25mA 0.015 0.1 % of Span From Drain of QEXT (4) OD = high IB VOS VVIN = 20mV vs Temperature Input Voltage Range (5) 5 ppm/°C 0.0001 % of Span/V >1 GΩ <1 μA 2.4/30 GΩ/pF 15 25 nA 0.3 1.5 mV 1.5 VVIN Noise, Referred to Input (2) Dynamic Response (1) (2) (3) (4) (5) % of Span 0.0001 Input Impedance (VIN) Input Bias Current (VIN) % of Span 0.0002 vs Supply (1) Output Leakage 0.02 8V to 40V Supply (1) (2) Output Resistance mA 0.1mA to 25mA vs Temperature vs Supply, VVSP mA mA 42 ± 6 Current Limit for Output Current Nonlinearity, IOUT/ISET 25 0 to 36 0.1Hz to 10Hz; IOUT = 4mA μV/°C 0 to 12 V 2.5 μVPP See Dynamic Performance Section Includes input amplifier, but excludes RSET tolerance. Offset current is the deviation from the current ratio of ISET to IIS (output current). See Typical Characteristics. Span is the change in output current resulting from a full-scale change in input voltage. Within compliance range limited by (+VVSP – 2V) +VDS required for linear operation of QEXT. See Application Information, Input Voltage section. Copyright © 2006–2011, Texas Instruments Incorporated 3 XTR111 SBOS375C – NOVEMBER 2006 – REVISED JUNE 2011 www.ti.com ELECTRICAL CHARACTERISTICS (continued) Boldface limits apply over the specified temperature range: TA = –40°C to +85°C. All specifications at TA = +25°C, VVSP = +24V, RSET = 2.0kΩ, REGF connected to REGS; OD = Low, External FET connected, unless otherwise noted. XTR111 PARAMETER CONDITIONS MIN TYP MAX RLOAD = 5kΩ 2.85 3.0 3.15 UNIT V-Regulator Output (REGF) Voltage Reference (6) vs Temperature (6) vs Supply (6) Bias Current into REGS (6) ppm/°C 0.1 mV/V μA 0.8 Load Regulation 0.6mA to 5mA Supply Regulation (6) 3 RLOAD = 5kΩ Output Current 5 0.01 mV/mA mV/V 5 Short-Circuit Output Current V 30 mA 21 mA DIGITAL INPUT (OD) VIL Low-Level Threshold 0.6 VIH High-Level Threshold 1.8 VOD < 5.5V Internal Pull-Up Current V V μA 4 DIGITAL OUTPUT (EF) IOH Leakage Current (Open Drain) μA 1 VOL Low-Level Output Voltage IEF = 2.2mA IOL Current to 400mV Level 0.8 VEF = 400mV 2 V mA POWER SUPPLY Specified Voltage Range +8 Operating Voltage Quiescent Current (6) +40 V 550 μA +7 to +44 IQ IOUT = 0mA 450 V TEMPERATURE RANGE Specified Range –40 +85 °C Operating Range –55 +125 °C Package Thermal Impedance, θJA (6) 4 DFN 70 °C/W MSOP 63 °C/W See Typical Characteristics. Copyright © 2006–2011, Texas Instruments Incorporated XTR111 SBOS375C – NOVEMBER 2006 – REVISED JUNE 2011 www.ti.com PIN CONFIGURATIONS DGQ PACKAGE MSOP-10 TOP VIEW VSP 1 IS 2 VG 3 REGS 4 REGF 5 Exposed Thermal Die Pad on Underside. (Must be connected to GND) DRC PACKAGE DFN-10 TOP VIEW 10 GND 9 OD 8 EF 7 SET 6 VIN VSP 1 IS 2 VG 3 REGS 4 REGF 5 Exposed Thermal Die Pad on Underside. (Must be connected to GND) 10 GND 9 OD 8 EF 7 SET 6 VIN Pad Pad PIN DESCRIPTIONS PIN NAME 1 VSP 2 IS Source Connection 3 VG Gate Drive 4 REGS Regulator Sense 5 REGF Regulator Force 6 VIN Input Voltage 7 SET Transconductance Set 8 EF Error Flag (Active Low) 9 OD Output Disable (Active High) 10 GND Negative Supply Pad Pad Exposed Thermal Pad must be connected to GND Copyright © 2006–2011, Texas Instruments Incorporated FUNCTION Positive Supply 5 XTR111 SBOS375C – NOVEMBER 2006 – REVISED JUNE 2011 www.ti.com TYPICAL CHARACTERISTICS At TA = +25°C and VVSP = +24V, unless otherwise noted. QUIESCENT CURRENT vs TEMPERATURE 700 530 650 510 Quiescent Current (mA) Quiescent Current (mA) QUIESCENT CURRENT vs SUPPLY VOLTAGE 550 490 470 450 430 410 390 600 550 500 450 400 350 370 350 300 5 10 15 20 25 30 35 40 45 -75 -50 -25 Supply Voltage (V) Figure 1. GAIN vs FREQUENCY 75 100 125 POWER-SUPPLY REJECTION RATIO vs FREQUENCY See Applications Information, Dynamic Performance RSET = 2kW, RLOAD = 2kW RSET = 2kW, No Bypass Cap 120 20 100 RSET = 2kW, RLOAD = 600W PSRR (dB) Gain (dB) 50 140 30 0 25 Figure 2. 40 10 0 Temperature (°C) RSET = 2kW, RLOAD = 200W -10 80 60 40 -20 20 -30 Gain = VLOAD/VVIN 0 -40 1k 10k 100k 1M 10M 10 100 Frequency (Hz) Figure 3. 10k 100k 1M Figure 4. 0.1Hz to 10Hz NOISE, RTI INPUT-REFERRED NOISE SPECTRUM 100m IOUT = 4mA IOUT = 2mA IR Noise (VRMS/ÖHz) 1mV/div 1k Frequency (Hz) 10m 1m 100n 10n 1s/div 1 10 100 1k 10k 100k Frequency (Hz) Figure 5. 6 Figure 6. Copyright © 2006–2011, Texas Instruments Incorporated XTR111 SBOS375C – NOVEMBER 2006 – REVISED JUNE 2011 www.ti.com TYPICAL CHARACTERISTICS (continued) At TA = +25°C and VVSP = +24V, unless otherwise noted. GAIN ERROR DISTRIBUTION -0.01 -0.009 -0.008 -0.007 -0.006 -0.005 -0.004 -0.003 -0.002 -0.001 0 0.001 0.002 0.003 0.004 0.005 0.006 0.007 0.008 0.009 0.01 -0.1 -0.09 -0.08 -0.07 -0.06 -0.05 -0.04 -0.03 -0.02 -0.01 0 0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08 0.09 0.1 Population Population NONLINEARITY DISTRIBUTION Gain Error (%) Nonlinearity (%) Figure 7. Figure 8. NONLINEARITY vs TEMPERATURE NONLINEARITY DRIFT DISTRIBUTION (IOUT = 0.1mA to 25mA; T = –55°C to +125°C) 0.03 0.02 Population Nonlinearity (%) 0.1mA to 25mA 0.01 0 4mA to 20mA -0.01 -0.02 -0.03 -75 -50 -25 0 25 50 75 100 0 125 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 Nonlinearity Drift (ppm/°C) Temperature (°C) Figure 9. Figure 10. GAIN ERROR vs TEMPERATURE GAIN ERROR DRIFT DISTRIBUTION (IOUT = 0.1mA to 25mA; T = –55°C to +125°C) 0.15 0.05 Population Gain Error (%) 0.10 4mA to 20mA 0 -0.05 0.1mA to 25mA -0.10 -0.15 -75 -50 -25 0 25 50 Temperature (°C) Figure 11. Copyright © 2006–2011, Texas Instruments Incorporated 75 100 125 -10 -9 -8 -7 -6 -5 -4 -3 -2 -1 0 Gain Error Drift (ppm/°C) Figure 12. 7 XTR111 SBOS375C – NOVEMBER 2006 – REVISED JUNE 2011 www.ti.com TYPICAL CHARACTERISTICS (continued) At TA = +25°C and VVSP = +24V, unless otherwise noted. TYPICAL NONLINEARITY (2pt Calibration at 0.1mA and 25mA) 0.0020 0.0020 0.0015 0.0015 0.0010 0.0010 Nonlinearity (%) Nonlinearity (%) TYPICAL NONLINEARITY (2pt Calibration at 4mA and 20mA) 0.0005 0.000 -0.0005 0.0005 0.000 -0.0005 -0.0010 -0.0010 -0.0015 -0.0015 -0.0020 -0.0020 4 8 12 16 0 20 5 10 IOUT (mA) 0.010 TYPICAL NONLINEARITY (2pt Calibration at 0.1mA and 36mA) INPUT VOLTAGE RANGE LIMIT TO THE POSITIVE SUPPLY vs TEMPERATURE 3.0 VVSP = 12V 2.9 Input Voltage Range Limit VVSP - VVIN (V) Nonlinearity (%) 25 Figure 14. 0.006 0.004 0.002 0.000 -0.002 -0.004 -0.006 2.8 2.7 2.6 2.5 2.4 2.3 2.2 2.1 -0.008 2.0 -0.010 0 5 10 15 20 25 30 35 40 -75 -50 0 -25 IOUT (mA) 25 50 75 100 125 Temperature (°C) Figure 15. Figure 16. OUTPUT SWING OF THE VOLTAGE ON IS PIN (VIS) vs OUTPUT CURRENT OUTPUT SWING OF THE VOLTAGE ON IS PIN (VIS) vs TEMPERATURE 3.0 1.8 1.7 2.5 20mA 1.6 2.0 VVSP - VIS (V) VVSP - VIS (V) 20 Figure 13. Seven Typical Units Shown 0.008 15 IOUT (mA) 1.5 1.0 1.5 10mA 1.4 1.3 4mA 1.2 0.5 1.1 0 1.0 0 8 5 10 15 20 25 30 35 40 -75 -50 -25 0 25 50 Output Current (mA) Temperature (°C) Figure 17. Figure 18. 75 100 125 Copyright © 2006–2011, Texas Instruments Incorporated XTR111 SBOS375C – NOVEMBER 2006 – REVISED JUNE 2011 www.ti.com TYPICAL CHARACTERISTICS (continued) At TA = +25°C and VVSP = +24V, unless otherwise noted. INPUT OFFSET VOLTAGE DRIFT DISTRIBUTION Population Population INPUT OFFSET VOLTAGE DISTRIBUTION -1.2 -1.0 -0.8 -0.6 -0.4 -0.2 0 0.2 0.4 0.6 0.8 1.0 1.2 -5 -4 -3 -2 VOS (mV) -1 Figure 19. 1 2 3 4 5 Figure 20. INPUT OFFSET VOLTAGE vs SUPPLY VOLTAGE AMPLIFIER INPUT BIAS CURRENT vs TEMPERATURE 100 30 80 28 60 26 Input Bias Current (nA) Input Offset Voltage (mV) 0 VOS (mV/°C) 40 20 0 -20 -40 24 22 20 18 16 -60 14 -80 12 10 -100 0 10 20 30 40 50 -75 -50 -25 Supply Voltage (V) 0 25 50 75 100 125 Temperature (°C) Figure 21. Figure 22. OUTPUT CURRENT LIMIT DISTRIBUTION OUTPUT CURRENT LIMIT vs TEMPERATURE 50 49 Population Current Limit (mA) 48 47 46 45 44 43 42 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 41 Current Limit (mA) Figure 23. Copyright © 2006–2011, Texas Instruments Incorporated 40 -75 -50 -25 0 25 50 75 100 125 Temperature (°C) Figure 24. 9 XTR111 SBOS375C – NOVEMBER 2006 – REVISED JUNE 2011 www.ti.com TYPICAL CHARACTERISTICS (continued) At TA = +25°C and VVSP = +24V, unless otherwise noted. REGULATOR VOLTAGE DISTRIBUTION REGULATOR VOLTAGE DRIFT DISTRIBUTION ILOAD = 0.6mA 2.850 2.865 2.880 2.895 2.910 2.925 2.940 2.955 2.970 2.985 3 3.015 3.030 3.045 3.060 3.075 3.090 3.105 3.120 3.135 3.150 Population Population ILOAD = 0.6mA 0 10 20 30 40 50 60 70 80 More Regulator Voltage Drift (ppm/°C) Regulator Voltage (V) Figure 26. REGULATOR INPUT BIAS CURRENT DISTRIBUTION (Current into REGS Pin) REGULATOR INPUT BIAS CURRENT DRIFT DISTRIBUTION (Drift of Current into REGS Pin) -4.0 -3.6 -3.2 -2.8 -2.4 -2.0 -1.6 -1.2 -0.8 -0.4 0 0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2 3.6 4.0 Population Population Figure 25. 0 0.5 1.0 1.5 Figure 27. REGULATOR VOLTAGE vs SUPPLY VOLTAGE 3.0 3.5 4.0 4.5 5.0 REGULATOR VOLTAGE vs TEMPERATURE 3.05 ILOAD = 0.6mA 3.04 ILOAD = 0.6mA 3.04 3.03 3.03 Regulator Voltage (V) Regulator Voltage (V) 2.5 Figure 28. 3.05 3.02 3.01 3.00 2.99 2.98 3.02 3.01 3.00 2.99 2.98 2.97 2.97 2.96 2.96 2.95 2.95 0 5 10 15 20 25 30 Supply Voltage (V) Figure 29. 10 2.0 VREGS Input Bias Current Drift (nA/°C) VREGS Input Bias Current (mA) 35 40 45 50 -75 -50 -25 0 25 50 75 100 125 Temperature (°C) Figure 30. Copyright © 2006–2011, Texas Instruments Incorporated XTR111 SBOS375C – NOVEMBER 2006 – REVISED JUNE 2011 www.ti.com TYPICAL CHARACTERISTICS (continued) At TA = +25°C and VVSP = +24V, unless otherwise noted. STEP RESPONSE: VFS = 4V, RSET = 2kΩ, RLD = 600Ω (Rising Edge Depends on CGATE at VG Pin) STEP RESPONSE: VFS = 2.5V, RSET = 1.25kΩ, RLD = 600Ω (Rising Edge Depends on CGATE at VG Pin) Photo taken with CGATE = 130pF Photo taken with CGATE = 130pF 5V/div 10V/div 5V/div 2V/div 10ms/div 10ms/div Figure 31. Figure 32. REGULATOR LOAD TRANSIENT (VREG Gain = 1V, VREGF = 3V, CL = 470nF, ILOAD = 3mA ± 0.3mA) REGULATOR LOAD TRANSIENT (VREG Gain = 4V, VREGF = 12V, CL = 470nF, ILOAD = 3mA ± 0.3mA) 2V/div 10mV/div 10mV/div 1V/div 40ms/div 40ms/div Figure 33. Figure 34. Maximum Regulator Output Current (mA) MAXIMUM REGULATOR CURRENT vs TEMPERATURE 29 27 25 23 21 19 17 15 -75 -50 -25 0 25 50 75 100 125 Temperature (°C) Figure 35. Copyright © 2006–2011, Texas Instruments Incorporated 11 XTR111 SBOS375C – NOVEMBER 2006 – REVISED JUNE 2011 www.ti.com APPLICATION INFORMATION used during power-on, multiplexing and other conditions where the output should present no current. It has an internal pull-up that causes the XTR111 to come up in output disable mode unless the OD pin is tied low. The XTR111 is a voltage-controlled current source capable of delivering currents from 0mA to 36mA. The primary intent of the device is to source the commonly-used industrial current ranges of 0mA–20mA or 4mA–20mA. The performance is specified for a supply voltage of up to 40V. The maximum supply voltage is 44V. The voltage-to-current ratio is defined by an external resistor, RSET; therefore, the input voltage range can be freely set in accordance with the application requirement. The output current is cascoded by an external P-Channel MOSFET transistor for large voltage compliance extending below ground, and for easy power dissipation. This arrangement ensures excellent suppression of typical interference signals from the industrial environment because of the extremely high output impedance and wide voltage compliance. The onboard voltage regulator can be adjusted between 3V to 15V and delivers up to 5mA load current. It is intended to supply signal conditioning and sensor excitation in 3-wire sensor systems. Voltages above 3V can be set by a resistive divider. Figure 36 shows a basic connection for the XTR111. The input voltage VVIN reappears across RSET and controls 1/10 of the output current. The I-Mirror has a precise current gain of 10. This configuration leads to the transfer function: IOUT = 10 • (VVIN/RSET) The output of the voltage regulator can be set over the range of 3V to 12V by selecting R1 and R2 using the following equation. VREGF = 3V · (R1 + R2)/R2 (1) An error detection circuit activates a logic output (error flag) in case the output current cannot correctly flow. It indicates a wire break, high load resistor, or loss of headroom for the current output to the positive supply. The output disable (OD) provided can be VVSP = 24V Supply C1 1 VSP REGF I-Mirror 5 9 OD IS R1 5.6kW (Pull Low for Normal Operation) 8 EF 2 15W (1) REGS S Q2 4 Q1 G 3 VG D 3V 15W R2 8.2kW 5V Load 6 10nF 0mA to 20mA 4mA to 20mA VIN (± Load Ground) Signal Source (Sensor or DAC, for example) GND 10 SET 7 RSET IOUT = 10 ( RV ) VIN SET Figure 36. Basic Connection for 0mA to 20mA Related to 0V to 5V Signal Input. The Voltage Regulator is Set to 5V Output 12 Copyright © 2006–2011, Texas Instruments Incorporated XTR111 www.ti.com EXPLANATION OF PIN FUNCTIONS VIN: This input is a conventional, noninverting, high-impedance input of the internal operational amplifier (OPA). The internal circuitry is protected by clamp diodes to supplies. An additional clamp connected to approximately 18V protects internal circuitry. Place a small resistor in series with the input to limit the current into the protection if voltage can be present without the XTR111 being powered. Consider a resistor value equal to RSET for bias current cancellation. SET: The total resistance connected between this pin and VIN reference sets the transconductance. Additional series resistance can degrade accuracy and drift. The voltage on this pin must not exceed 14V because this pin is not protected to voltages above this level. IS: This output pin is connected to the transistor source of the external FET. The accuracy of the output current to IS is achieved by dynamic error correction in the current mirror. This pin should never be pulled more than 6.5V below the positive supply. An internal clamp is provided to protect the circuit; however, it must be externally current-limited to less than 50mA. VG: The gate drive for the external FET is protected against shorts to the supply and GND. The circuit is clamped so that it will not drive more than 18V below the positive supply. The external FET should be protected if its gate could be externally pulled beyond its ratings. REGF: The output of the regulator buffer can source up to 5mA current, but has very limited (less than 50μA) sinking capability. The maximum short-circuit current is in the range of 15mA to 25mA, changing over temperature. REGS: This pin is the sense input of the voltage regulator. It is referenced to an internal 3V reference circuit. The input bias current can be up to 2μA. Avoid capacitive loading of REGS that may compromise the loop stability of the voltage regulator. VSP: The supply voltage of up to a maximum of 44V allows operation in harsh industrial environment and provides headroom for easy protection against over-voltage. Use a large enough bypass capacitor (> 100nF) and eventually a damping inductor or a small resistor (5Ω) to decouple the XTR111 supply from the noise typically found on the 24V supplies. Copyright © 2006–2011, Texas Instruments Incorporated SBOS375C – NOVEMBER 2006 – REVISED JUNE 2011 EF : The active low error flag (logic output) is intended for use with an external pull-up to logic-high for reliable operation when this output is used. However, it has a weak internal pull-up to 5V and can be left unconnected if not used. OD: This control input has a 4μA internal pull-up disabling the output. A pull-down or short to GND is required to activate the output. Controlling OD reduces output glitches during power-on and power-off. This logic input controls the output. If not used, connect to GND. The regulator is not affected by OD. EXTERNAL CURRENT LIMIT The XTR111 does not provide internal current limit for the case of when the external FET is forced to low impedance. The internal current source controls the current, but a high current from IS to GND forces an internal voltage clamp between VSP and IS to turn on. This results in a low resistance path and the current is only limited by the load impedance and the current capability of the external FET. A high current can destroy the IC. With the current loop interrupted (the load disconnected) the external MOSFET is fully turned on with large gate to source voltage stored in the gate capacitance. In the moment the loop is closed (the load connected) current flows into the load. But for the first few micro-seconds the MOSFET is still turned on and destructive current can flow, depending on the load impedance. An external current limit is recommended to protect the XTR111 from this condition. Figure 37a shows an example of a current limit circuit. The current should be limited to 50mA. The 15Ω resistor (R6) limits the current to approximately 37mA (33mA when hot). The PNP transistor should allow a peak current of several hundred mA. An example device is the (KST)2907. Power dissipation is not normally critical because the peak current duration is only a few micro-seconds. However, observe the leakage current through the transistor from IS to VG. The addition of this current limiting transistor and R6 still require time to discharge the gate of the external MOSFET. R7 and C3 are added for this reason, as well as to limit the steepness of external distortion pulses. Additional EMI and over-voltage protection may be required according to the application. Figure 37b is a universal and basic current limiter circuit, using PNP or NPN transistors that can be connected in the source (IS to S) or in the drain output (in series with the current path). This circuit does not contribute to leakage currents. Consider adding an output filter like R7 and C3 in this limiter circuit. 13 XTR111 SBOS375C – NOVEMBER 2006 – REVISED JUNE 2011 www.ti.com IS IS R6 15W R6 15W Q2 Q1 VG Q2 R7 15W R8 5kW IOUT C3 10nF Q3 Table 1 lists some example devices in SO-compatible packages, but other devices can be used as well. Avoid external capacitance from IS. This capacitance could be compensated by adding additional capacitance from VG to IS; however, this compensation may slow the output down. Q1 VG IOUT a) Gate-Controlled Current Limit the OD pin high disables the gate driver and closes a switch connecting an internal 3kΩ resistor from the VSP pin to the VG pin. This resistor discharges the gate of the external FET and closes the channel; see Figure 38. The drain-to-source breakdown voltage should be selected high enough for the application. Surge voltage protection might be required for negative over-voltages. For positive over-voltages, a clamp diode to the 24V supply is recommended, protecting the FET from reversing. b) Serial Current Limit Figure 37. External Current Limit Circuits EXTERNAL MOSFET The XTR111 delivers the precise output current to the IS pin. The voltage at this pin is normally 1.4V below VVSP. VSP 16V This output requires an external transistor (QEXT) that forms a cascode for the current output. The transistor must be rated for the maximum possible voltage on VOUT and must dissipate the power generated by the current and the voltage across it. The gate drive (VG) can drive from close to the positive supply rail to 16V below the positive supply voltage (VVSP). Most modern MOSFETs accept a maximum VGS of 20V. A protection clamp is only required if a large drain gate capacitance can pulse the gate beyond the rating of the MOSFET. Pulling OD Switch 3kW VG GND Figure 38. Equivalent Circuit for Gate Drive and Disable Switch Table 1. P-Channel MOSFET (Examples) (1) (1) 14 MANUFACTURER PART NO. BREAKDOWN VGS PACKAGE C-GATE Infineon BSP170P –60V SOT-223 328pF NEC 2SJ326-Z –60V Spec. 320pF ON Semiconductor NTF2955 –60V SOT-223 492pF Supertex Inc. TP2510 –100V TO-243AA 80pF Data from published product data sheet; not ensured. Copyright © 2006–2011, Texas Instruments Incorporated XTR111 SBOS375C – NOVEMBER 2006 – REVISED JUNE 2011 www.ti.com DYNAMIC PERFORMANCE The rise time of the output current is dominated by the gate capacitance of the external FET. The accuracy of the current mirror relies on the dynamic matching of multiple individual current sources. Settling to full resolution may require a complete cycle lasting around 100μs. Figure 39 shows an example of the ripple generated from the individual current source values that average to the specified accuracy over the full cycle. The output glitch magnitude depends on the mismatch of the internal current sources. It is approximately proportional to the output current level and scales directly with the load resistor value. It will differ slightly from part to part. The effects of filtering the output are shown in Figure 40 and Figure 41. External FET 50mV/div No Filter 500W 20ms/div Figure 39. Output Noise without Filter into 500Ω External FET 50mV/div Load Capacitor CF 10nF 500W 20ms/div Figure 40. Output with 10nF Parallel to 500Ω Copyright © 2006–2011, Texas Instruments Incorporated 15 XTR111 SBOS375C – NOVEMBER 2006 – REVISED JUNE 2011 www.ti.com External FET NOTE: Scale has been changed from Figure 38 and Figure 39. 5mV/div Typical Filter RF 10kW 500W CF 10nF 20ms/div Figure 41. Output with Additional Filter OUTPUT ERROR FLAG AND DISABLE INPUT INPUT VOLTAGE The XTR111 has additional internal circuitry to detect an error in the output current. In case the controlled output current cannot flow due to a wire break, high load resistance or the output voltage level approaching the positive supply, the error flag (EF), an open drain logic output, pulls low. When used, this digital output requires external pull-up to logic high (the internal pull-up current is 2μA). The input voltage range for a given output current span is set by RSET according to the transfer function. Select a precise and low drift resistor for best performance, because resistor drift directly converts into drift of the output current. Careful layout must also minimize any series resistance with RSET and the VIN reference point. The output disable (OD) is a logic input with approximately 4μA of internal pull-up to 5V. The XTR111 comes up with the output disabled until the OD pin is pulled low. Logic high disables the output to zero output current. It can be used for calibration, power-on and power-off glitch reduction, and for output multiplexing with other outputs connected to the same terminal pin. Power-on while the output is disabled (OD = high) cannot fully suppress output glitching. While the supply voltage passes through the range of 3V to 4V, internal circuits turn on. Additional capacitance between pins VG and IS can suppress the glitch. The smallest glitch energy appears with the OD pin left open; for practical use, however, this pin can be driven high through a 10kΩ resistor before the 24V supply is applied, if logic voltage is available earlier. Alternatively, an open drain driver can control this pin using the internal pull-up current. Pull-up to the internal regulator tends to increase the energy because of the delay of the regulator voltage increase, again depending on the supply voltage rise time for the first few volts. 16 The input voltage is referred to the grounding point of RSET. Therefore, this point should not be distorted from other currents. Assuming a 5V full-scale input signal for a 20mA output current, RSET is 2.5kΩ. A resistance uncertainty of just 2.5Ω already degrades the accuracy to below 0.1%. The linear input voltage range extends from 0V to 12V, or 2.3V below the positive supply voltage (whichever is smaller). The lowest rated supply voltage accomodates an input voltage range of up to 5V. Potential clipping is not detected by an error signal; therefore, safe design guard banding is recommended. Do not drive the input negative (referred to GND) more than 300mV. Higher negative voltages turn on the internal protection diodes. Insert a resistor in series with the input if negative signals can occur eventually during power-on or -off or during other transient conditions. Select a resistor value limiting the possible current to 0.3mA. Higher currents are non-destructive (see Absolute Maximum Ratings), but they can produce output current glitches unless in disable mode. Copyright © 2006–2011, Texas Instruments Incorporated XTR111 SBOS375C – NOVEMBER 2006 – REVISED JUNE 2011 www.ti.com More protection against negative input signals is provided using a standard diode and a 2.2kΩ resistor, as shown in Figure 42. 2.2kW V-Signal VIN 1N4148 Figure 42. Enhanced Protection Against Negative Overload of VIN 4mA–20mA OUTPUT The XTR111 does not provide internal circuits to generate 4mA with 0V input signal. The most common way to shift the input signal is a two resistor network connected to a voltage reference and the signal source, as shown in Figure 43. This arrangement allows easy adjustment for over-and under-range. The example assumes a 5V reference (VREF) that equals the full-scale signal voltage and a signal span of 0V to 5V for 4mA to 20mA (IMIN to IMAX) output. LEVEL SHIFT OF 0V INPUT AND TRANSCONDUCTANCE TRIM The XTR111 offers low offset voltage error at the input, which normally does not require cancellation. If the signal source cannot deliver 0V in a single-supply circuit, an additional resistor from the SET pin to a positive reference voltage or the regulator output (Figure 44) can shift the zero level for the input (VIN) to a positive voltage. Therefore, the signal source can drive this value within a positive voltage range. The example shows a +100mV (102.04mV) offset generated to the signal input. The larger this offset, however, the more influence of its drift and inaccuracy is seen in the output signal. The voltage at SET should not be larger than 12V for linear operation. Transconductance (the input voltage to output current ratio) is set by RSET. The desired resistor value may be found by choosing a combination of two resistors. XTR111 I-V Amp VIN The voltage regulator output or a more precise reference can be used as VREF. Observe the potential drift added by the drift of the resistors and the voltage reference. Reference Voltage 5V Input Voltage 0V to 5V 5V Reference R1 40kW R2 10kW 120kW SET +100mV Offset RSET 2kW VIN 1V to 5V Figure 44. Input Voltage Level Shift for 0mA Output Current Figure 43. Resistive Divider for IMIN to IMAX Output (4mA to 20mA) with 0V to VFS Signal Source Copyright © 2006–2011, Texas Instruments Incorporated 17 XTR111 SBOS375C – NOVEMBER 2006 – REVISED JUNE 2011 www.ti.com VOLTAGE REGULATOR The externally adjustable voltage regulator provides up to 5mA of current. It offers drive (REGF) and sense (REGS) to allow external setting of the output voltage as shown in Figure 45. The sense input (REGS) is referenced to 3.0V representing the lowest adjustable voltage level. An external resistor divider sets VREGF. VREGF = VREGS · (R1 + R2)/R2 Table 2 provides example values for the regulator adjustment resistors. Table 2. Examples for the Resistor Values Setting the Regulator Voltage VREGF (1) R1 R2 3V 0 — 3.3V 3.3kΩ 33kΩ 5V 5.6kΩ 8.2kΩ 12.4V 27kΩ 8.6kΩ (1) Values have been rounded. REGF 3V The voltage at REGF is limited by the supply voltage. If the supply voltage drops close to the set voltage, the driver output saturates and follows the supply with a voltage drop of less than 1V (depending on load current and temperature). For good stability and transient response, use a load capacitance of 470nF or larger. The bias current into the sense input (REGS) is typically less than 1μA. This current should be considered when selecting high resistance values for the voltage setting because it lowers the voltage and produces additional temperature dependence. The REGF output cannot sink current. In case of supply voltage loss, the output is protected against the discharge currents from load capacitors by internal protection diodes; the peak current should not exceed 25mA. If the voltage regulator output is not used, connect REGF to REGS (the 3V mode) loaded with a 2.2nF capacitor. Alternatively, overdrive the loop pulling REGS high (see Figure 45d). REGF VREG 470nF REGS R1 5.6kW REG REGS 470nF R2 8.2kW 3V 3V (a) (b) VSP 220W 1kW REGF REGF 1kW 5V Source VREG 470nF R3 47kW REGS R1 5.6kW REGS 3V R2 8.2kW 3V (c) (d) Figure 45. Basic Connections of the Voltage Regulator 18 Copyright © 2006–2011, Texas Instruments Incorporated XTR111 SBOS375C – NOVEMBER 2006 – REVISED JUNE 2011 www.ti.com APPLICATION BLOCK DIAGRAMS 1 VSP 5 5V C2 470nF R1 2kW 4 Current Mirror REGF OD 9 EF 8 IS 2 REGS 15W (1) R2 3kW S Q2 VG Q1 G 3 D 3V 15W Digital I/O 12-Bit Digital-to-Analog Converter DAC7551 R3 2.5kW 6 10nF VIN GND SET 10 7 0mA to 20mA CLOAD RSET 2.5kW RLOAD Figure 46. Current Using 0V to 5V Input from a 12-Bit Digital-to-Analog Converter DAC7551 1 VSP 5V C2 470nF R1 2kW 5 REGF 4 REGS Current Mirror OD 9 EF 8 IS 2 15W (1) REF3040 4096mV Voltage Reference R2 3kW S Q2 VG 3 Q1 G D 3V 15W Digital I/O 16-Bit Digital-to-Analog Converter DAC8551 R3 2kW 6 10nF VIN SET R4 817.2kW 7 GND 10 Load CLOAD NOTE: Calculate RSET for R4 parallel to RSET. RLOAD 0mA to 20mA output for 10mV to 4096mV input or a code of 160b to 65536b RSET 2kW (1.995kW) Figure 47. Precision Current Output with Signal from 16-Bit DAC. Input Offset Shifted (R4) by 10mV for Zero Adjustment Range Copyright © 2006–2011, Texas Instruments Incorporated 19 XTR111 SBOS375C – NOVEMBER 2006 – REVISED JUNE 2011 www.ti.com 1 VSP 5 4 OD 9 EF 8 IS 2 Current Mirror REGF REGS 15W (1) S Q2 VG Q1 G 3 D 3V 15W 0V to 10V Signal Input 6 10nF VIN GND SET 10 7 Load SW1 RSET 5kW CLOAD RLOAD Current (open) or Voltage (close) Output When output disabled and SW1 is closed, pin 7 may generate an error signal. Figure 48. 0V to 10V or 0mA to 20mA Output Selected by Jumper (SW1) (1) (a) (b) R4 100W +24V Q2 NPN Q2 NPN R3 1kW R3 1kW REGF REGF R1 10kW REGS 3V C2 470nF REGS 6V C2 470nF R2 10kW NOTE: (1) Resistor R4 can be calculated to protect Q2 from over current in fault conditions. Figure 49. Voltage Regulator Current Boost Using a Standard NPN Transistor 20 Copyright © 2006–2011, Texas Instruments Incorporated XTR111 SBOS375C – NOVEMBER 2006 – REVISED JUNE 2011 www.ti.com PACKAGE AND HEAT SINKING The dominant portion of power dissipation for the current output is in the external FET. The XTR111 only generates heat from the supply voltage with the quiescent current, the internal signal current that is 1/10 of the output current, and the current and internal voltage drop of the regulator. The exposed thermal pad on the bottom of the XTR111 package allows excellent heat dissipation of the device into the printed circuit board (PCB). THERMAL PAD The thermal pad must be connected to the same voltage potential as the device GND pin. Packages with an exposed thermal pad are specifically designed to provide excellent power dissipation, but board layout greatly influences overall heat dissipation. The thermal resistance from junction-to-ambient (TJA) is specified for the packages with the exposed thermal pad soldered to a normalized PCB, as described in Technical Brief SLMA002, PowerPAD Thermally-Enhanced Package. See also EIA/JEDEC Specifications JESD51-0 to 7, QFN/SON PCB Attachment (SLUA271), and Quad Flatpack No-Lead Logic Packages (SCBA017). These documents are available for download at www.ti.com. NOTE: All thermal models have an accuracy variation of 20%. Component population, layout of traces, layers, and air flow strongly influence heat dissipation. Worst-case load conditions should be tested in the real environment to ensure proper thermal conditions. Minimize thermal stress for proper long-term operation with a junction temperature well below +125°C. LAYOUT GUIDELINES The leadframe die pad should be soldered to a thermal pad on the PCB. A mechanical data sheet showing an example layout is attached at the end of this data sheet. Refinements to this layout may be required based on assembly process requirements. Mechanical drawings located at the end of this data sheet list the physical dimensions for the package and pad. The five holes in the landing pattern are optional, and are intended for use with thermal vias that connect the leadframe die pad to the heatsink area on the PCB. Soldering the exposed pad significantly improves board-level reliability during temperature cycling, key push, package shear, and similar board-level tests. Even with applications that have low-power dissipation, the exposed pad must be soldered to the PCB to provide structural integrity and long-term reliability. space REVISION HISTORY NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision B (June, 2010) to Revision C • Corrected wiring error in Figure 46 ..................................................................................................................................... 19 Changes from Revision A (August, 2007) to Revision B • Page Page Corrected errors in Figure 37 .............................................................................................................................................. 14 Copyright © 2006–2011, Texas Instruments Incorporated 21 PACKAGE OPTION ADDENDUM www.ti.com 24-May-2011 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) XTR111AIDGQR ACTIVE MSOPPowerPAD DGQ 10 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR XTR111AIDGQRG4 ACTIVE MSOPPowerPAD DGQ 10 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR XTR111AIDGQT ACTIVE MSOPPowerPAD DGQ 10 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR XTR111AIDGQTG4 ACTIVE MSOPPowerPAD DGQ 10 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR XTR111AIDRCR ACTIVE SON DRC 10 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR XTR111AIDRCRG4 ACTIVE SON DRC 10 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR XTR111AIDRCT ACTIVE SON DRC 10 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR XTR111AIDRCTG4 ACTIVE SON DRC 10 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 24-May-2011 Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant XTR111AIDGQR MSOPPower PAD DGQ 10 2500 330.0 12.4 5.3 3.3 1.3 8.0 12.0 Q1 XTR111AIDGQT MSOPPower PAD DGQ 10 250 180.0 12.4 5.3 3.3 1.3 8.0 12.0 Q1 XTR111AIDRCR SON DRC 10 3000 330.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 XTR111AIDRCT SON DRC 10 250 180.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) XTR111AIDGQR MSOP-PowerPAD DGQ 10 2500 370.0 355.0 55.0 XTR111AIDGQT MSOP-PowerPAD DGQ 10 250 195.0 200.0 45.0 XTR111AIDRCR SON DRC 10 3000 367.0 367.0 35.0 XTR111AIDRCT SON DRC 10 250 210.0 185.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2012, Texas Instruments Incorporated