TI OPA2348CKGD4

OPA2348-HiRel
www.ti.com
SBOS482 – NOVEMBER 2009
1-MHz, 45-μA CMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIER
Check for Samples: OPA2348-HiRel
FEATURES
1
•
•
•
•
•
•
•
•
•
0°C to 70°C Known Good Die
Separated (Sawn) Die Mounted on Wafer Tape
Controlled Baseline
Low Quiescent Current (IQ): 45 μA (Typ)
Low Cost
Rail-to-Rail Input and Output
Single Supply: 2.1 V to 5.5 V
Input Bias Current: 0.5 pA (Typ)
High Speed:Power With Bandwidth: 1 MHz
APPLICATIONS
•
•
•
•
•
Portable Equipment
Battery-Powered Equipment
Smoke Alarms
CO Detectors
Medical Instrumentation
DESCRIPTION
The OPA2348 is a single-supply low-power CMOS operational amplifier. Featuring an extended bandwidth of 1
MHz and a supply current of 45 μA, the OPA2348 is useful for low-power applications on single supplies of 2.1 V
to 5.5 V.
Low supply current of 45 μA and an input bias current of 0.5 pA make the OPA2348 an optimal candidate for
low-power high-impedance applications such as smoke detectors and other sensors.
ORDERING INFORMATION (1)
(1)
(2)
TA
PACKAGE (2)
ORDERABLE PART NUMBER
TOP-SIDE MARKING
0°C to 70°C
KGD
OPA2348CKGD4
NA
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
web site at www.ti.com.
Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2009, Texas Instruments Incorporated
OPA2348-HiRel
SBOS482 – NOVEMBER 2009
www.ti.com
BARE DIE INFORMATION
DIE THICKNESS
BACKSIDE FINISH
BACKSIDE POTENTIAL
BOND PAD
METALLIZATION COMPOSITION
10 mils.
Silicon with backgrind
V-
Al-Si-Cu (0.5%)
Origin
a
c
b
d
Table 1. BOND PAD COORDINATES
2
DESCRIPTION
PAD NUMBER
a
b
c
d
V+
1
965.6
5
1041.8
81.2
Out A
2
839.4
5
915.6
81.2
-In A
3
713.2
5
789.4
81.2
+In A
4
587
5
663.2
81.2
Out B
5
383.6
5
459.8
81.2
-In B
6
257.4
5
333.6
81.2
+In B
7
131.2
5
207.4
81.2
V-
8
5
5
81.2
81.2
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): OPA2348-HiRel
OPA2348-HiRel
www.ti.com
SBOS482 – NOVEMBER 2009
½
391.4 mm
V+
½
½
Out A
-In A
Out B
1046.8 mm
60 mm
½
+In A
-In B
+In B
½
½
V-
60 mm
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): OPA2348-HiRel
3
OPA2348-HiRel
SBOS482 – NOVEMBER 2009
www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
ABSOLUTE MAXIMUM RATINGS (1)
over operating free-air temperature range (unless otherwise noted)
VS
Supply voltage, V– to V+
VIN
Input voltage, signal input terminals (2)
IIN
Input current, signal input terminals (2)
7.5 V
(V– – 0.5 V) to (V+ + 0.5 V)
10 mA
Output short-circuit duration (3)
Continuous
θJA
Thermal impedance, junction to free air (4)
TA
Operating free-air temperature
0°C to 70°C
TSTG
Storage temperature
–0°C to 70°C
TJ
Operating virtual-junction temperature
(1)
(2)
(3)
(4)
97.1°C/W
70°C
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
Input terminals are diode-clamped to the power-supply rails. Input signals that can swing more than 0.5 V beyond the supply rails should
be current-limited to 10 mA or less.
Short-circuit to ground, one amplifier per package.
The package thermal impedance is calculated in accordance with JESD 51-5.
RECOMMENDED OPERATING CONDITIONS
VS
Supply voltage, V– to V+
TA
Operating free-air temperature
4
Submit Documentation Feedback
MIN
MAX
2.1
5.5
UNIT
V
0
70
°C
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): OPA2348-HiRel
OPA2348-HiRel
www.ti.com
SBOS482 – NOVEMBER 2009
ELECTRICAL CHARACTERISTICS
VS = 2.5 V to 5.5 V, RL = 100 kΩ connected to VS/2, VOUT = VS/2 (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VOS
Input offset voltage
VS = 5 V, VCM = (V–) + 0.8 V
ΔVOS/
ΔT
Offset voltage drift over
temperature
PSRR
Offset voltage drift vs power
supply
Offset voltage channel
separation
VS = 2.5 V to 5.5 V, VCM < (V+) – 1.7 V
TA
(1)
MIN
25°C
TYP
MAX
1
5
Full range
UNIT
mV
6
Full range
4
25°C
60
Full range
μV/°C
175
μV/V
300
dc
25°C
0.2
μV/V
f = 1 kHz
25°C
134
dB
VCM
Input common-mode
voltage range
CMRR
Input common-mode
rejection ratio
IB
Input bias current
25°C
±0.5
±10
pA
IOS
Input offset current
25°C
±0.5
±10
pA
(V–) – 0.2 V < VCM < (V+) – 1.7 V
(V–) – 0.2
25°C
70
Full range
66
25°C
60
Full range
56
VS = 5.5 V, (V–) – 0.2 V < VCM < (V+) + 0.2 V
VS = 5.5 V, (V–) < VCM < (V+)
25°C
Input impedance
V
82
dB
71
1013||3
Differential
ZI
(V+) + 0.2
25°C
Ω||pF
1013||3
Common-mode
Input voltage noise
VCM < (V+) – 1.7 V, f = 0.1 Hz to 10 Hz
25°C
10
μVPP
Vn
Input voltage noise density
VCM < (V+) – 1.7 V, f = 1 kHz
25°C
35
nV/√Hz
In
Input current noise density
VCM < (V+) – 1.7 V, f = 1 kHz
25°C
4
fA/√Hz
VS = 5 V, RL = 100 kΩ, 0.025 V < VO < 4.975 V
AOL
Open-loop voltage gain
VS = 5V, RL = 5 kΩ, 0.125 V < VO < 4.875 V
RL = 100 kΩ, AOL > 94 dB
Voltage output swing from
rail
RL = 5 kΩ, AOL > 90 dB
25°C
94
Full range
90
25°C
90
Full range
88
25°C
25°C
CLOAD
Capacitive load drive
See Typical Characteristics
25°C
GBW
Gain-bandwidth product
CL = 100 pF
SR
Slew rate
CL = 100 pF, G = +1
ts
25
100
125
25
25°C
mV
125
±10
mA
25°C
1
MHz
25°C
0.5
V/μs
5
μs
CL = 100 pF, VS = 5.5 V, 2V- step, G = +1
25°C
Overload recovery time
VIN × Gain > VS
25°C
1.6
μs
THD+N
Total harmonic distortion
plus noise
CL = 100 pF, VS = 5.5 V, VO = 3 VPP, G = +1, f = 1 kHz
25°C
0.0023
%
IQ
Quiescent current
Per amplifier
25°C
45
(1)
Settling time
18
Full range
Output short-circuit current
dB
98
Full range
ISC
0.1%
108
0.01%
Full range
7
65
75
μA
Full range TA = 0°C to 70°C
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): OPA2348-HiRel
5
OPA2348-HiRel
SBOS482 – NOVEMBER 2009
www.ti.com
TYPICAL CHARACTERISTICS
TA = 25°C, RL = 100 kΩ connected to VS/2, VOUT = VS/2 (unless otherwise noted)
OPEN-LOOP GAIN AND PHASE vs FREQUENCY
PSRR AND CMRR vs FREQUENCY
140
100
0
80
–45
80
Gain
60
Phase
–90
40
20
–135
PSRR, CMRR (dB)
100
Phase (°)
Open-Loop Gain (dB)
120
CMRR
60
40
PSRR
20
0
–20
0.1
1
10
100
1k
10k
100k
1M
0
–180
10M
100
10
1k
Frequency (Hz)
MAXIMUM OUTPUT VOLTAGE vs FREQUENCY
6
10k
100k
1M
10M
Frequency (Hz)
CHANNEL SEPARATION vs FREQUENCY
140
VS = 5.5V
Channel Separation (dB)
Output Voltage (Vp-p)
5
VS = 5V
4
3
2
VS = 2.5V
1
120
100
80
60
0
1k
10k
100k
1M
100
10
10M
1k
QUIESCENT AND SHORT-CIRCUIT CURRENT
vs SUPPLY VOLTAGE
45
7
IQ
35
4
Output Voltage Swing (V)
10
Short-Circuit Current (mA)
55
+125°C
+25°C
1.5
–40°C
1
Sourcing Current
0.5
0
–0.5
–1
Sinking Current
–1.5
–40°C
+25°C
–2
25
1
3
3.5
4
4.5
5
5.5
+125°C
–2.5
0
5
10
15
20
Output Current (mA)
Supply Voltage (V)
6
10M
VS = ±2.5V
2
ISC
2.5
1M
2.5
13
2
100k
OUTPUT VOLTAGE SWING vs OUTPUT CURRENT
65
Quiescent Current (µA)
10k
Frequency (Hz)
Frequency (Hz)
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): OPA2348-HiRel
OPA2348-HiRel
www.ti.com
SBOS482 – NOVEMBER 2009
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, RL = 100 kΩ connected to VS/2, VOUT = VS/2 (unless otherwise noted)
OPEN-LOOP GAIN AND PSRR vs TEMPERATURE
COMMON-MODE REJECTION vs TEMPERATURE
130
100
Open-Loop Gain and
Power Supply Rejection (dB)
Common-Mode Rejection (dB)
AOL, RL = 100kΩ
90
V– < V CM < (V+) – 1.7V
80
V– < V CM < V+
70
60
120
AOL, RL = 5kΩ
110
100
90
80
PSRR
70
60
50
–75
–50
–25
0
25
50
75
100
125
–50
–75
150
–25
0
QUIESCENT AND SHORT-CIRCUIT CURRENT
vs TEMPERATURE
75
55
12
45
10
IQ
35
8
25
6
15
Input Bias Current (pA)
14
ISC
4
–25
0
25
50
75
100
125
100
125
150
1k
100
10
1
0.1
150
–75
–50
–25
0
25
50
75
100
Temperature (°C)
Temperature (°C)
OFFSET VOLTAGE PRODUCTION DISTRIBUTION
OFFSET VOLTAGE DRIFT MAGNITUDE
PRODUCTION DISTRIBUTION
125
150
25
20
16
Percentage of Amplifiers (%)
Typical production
distribution of
packaged units.
18
Percent of Amplifiers (%)
75
10k
Short-Circuit Current (mA)
Quiescent Current (µA)
65
–50
50
INPUT BIAS (IB) CURRENT vs TEMPERATURE
16
–75
25
Temperature (°C)
Temperature (°C)
14
12
10
8
6
4
Typical production
distribution of
packaged units.
20
15
10
5
2
0
0
–6
–5
–4
–3
–2
–1
0
1
2
3
4
5
6
1
Offset Voltage (mV)
2
3
4
5
6
7
8
9
10
11
12
Offset Voltage Drift (µV/°C)
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): OPA2348-HiRel
7
OPA2348-HiRel
SBOS482 – NOVEMBER 2009
www.ti.com
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, RL = 100 kΩ connected to VS/2, VOUT = VS/2 (unless otherwise noted)
SMALL-SIGNAL OVERSHOOT
vs LOAD CAPACITANCE
PERCENT OVERSHOOT vs LOAD CAPACITANCE
60
60
50
40
40
Overshoot (%)
Small-Signal Overshoot (%)
G = –1V/V, R FB = 100kW
50
30
G = +1V/V, R L = 100kW
20
30
20
G = ±5V/V, R FB = 100kW
G = –1V/V, R FB = 5kW
10
10
0
0
10
100
1k
10k
10
100
LARGE-SIGNAL STEP RESPONSE
G = +1V/V, R L = 100kW, CL = 100pF
20mV/div
500mV/div
SMALL-SIGNAL STEP RESPONSE
G = +1V/V, R L = 100kW, CL = 100pF
10µs/div
TOTAL HARMONIC DISTORTION + NOISE
vs FREQUENCY
INPUT CURRENT AND VOLTAGE NOISE
SPECTRAL DENSITY vs FREQUENCY
1.000
1k
100
IN
VN
100
10
1
10
1
10
100
1k
10k
100k
Total Harmonic Distortion + Noise (%)
1k
Current Noise (fA√Hz)
10k
Voltage Noise (nV/√Hz)
10k
Load Capacitance (pF)
2µs/div
0.100
0.010
0.001
10
100
1k
10k
100k
Frequency (Hz)
Frequency (Hz)
8
1k
Load Capacitance (pF)
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): OPA2348-HiRel
OPA2348-HiRel
www.ti.com
SBOS482 – NOVEMBER 2009
APPLICATION INFORMATION
OPA2348 op amps are unity-gain stable and suitable for a wide range of general-purpose applications.
The OPA2348 features wide bandwidth and unity-gain stability with rail-to-rail input and output for increased
dynamic range. Figure 1 shows the input and output waveforms for the OPA2348 in unity-gain configuration.
Operation is from a single 5-V supply with a 100-kΩ load connected to VS/2. The input is a 5-VPP sinusoid.
Output voltage is approximately 4.98 VPP.
Power-supply pins should be bypassed with 0.01-μF ceramic capacitors.
G = +1V/V, VS = +5V
Output (Inverted on Scope)
1V/div
5V
0V
20µs/div
Figure 1. Rail-to-Rail Input/Output
Operating Voltage
OPA2348 op amps are fully specified and tested from 2.5 V to 5.5 V. However, supply voltage may range from
2.1 V to 5.5 V. Parameters are tested over the specified supply range, a unique feature of the OPA2348. In
addition, all temperature specifications apply from 0°C to 70°C. Most behavior remains virtually unchanged
throughout the full operating voltage range. Parameters that vary significantly with operating voltages or
temperature are shown in the Typical Characteristics.
Common-Mode Voltage Range
The input common-mode voltage range of the OPA2348 extends 200 mV beyond the supply rails. This is
achieved with a complementary input stage—an N-channel input differential pair in parallel with a P-channel
differential pair. The N-channel pair is active for input voltages close to the positive rail, typically (V+) – 1.2 V to
300 mV above the positive supply, while the P-channel pair is on for inputs from 300 mV below the negative
supply to approximately (V+) – 1.4 V. There is a small transition region, typically (V+) – 1.4 V to (V+) – 1.2 V, in
which both pairs are on. This 200-mV transition region, shown in Figure 2, can vary ±300 mV with process
variation. Thus, the transition region (both stages on) can range from (V+) – 1.7 V to (V+) – 1.5 V on the low end,
up to (V+) – 1.1 V to (V+) – 0.9 V on the high end. Within the 200-mV transition region, PSRR, CMRR, offset
voltage, offset drift, and THD may be degraded compared to operation outside this region.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): OPA2348-HiRel
9
OPA2348-HiRel
SBOS482 – NOVEMBER 2009
www.ti.com
OFFSET VOLTAGE
vs FULL COMMON-MODE VOLTAGE RANGE
2
Offset Voltage (mV)
1.5
1
0.5
0
–0.5
–1
V–
V+
–1.5
–2
–0.5 0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
Common-Mode Voltage (V)
Figure 2. Behavior of Typical Transition Region at Room Temperature
Rail-to-Rail Input
The input common-mode range extends from (V–) – 0.2 V to (V+) + 0.2 V. For normal operation, inputs should
be limited to this range. The absolute maximum input voltage is 500 mV beyond the supplies. Inputs greater than
the input common-mode range but less than the maximum input voltage, while not valid, do not cause any
damage to the op amp. Unlike some other op amps, if input current is limited the inputs may go beyond the
power supplies without phase inversion, as shown in Figure 3.
VIN
G = +1V/V, V S = +5V
5V
1V/div
VOUT
0V
10µs/div
Figure 3. No Phase Inversion With Inputs Greater Than Power-Supply Voltage
Normally, input currents are 0.5 pA. However, large inputs (greater than 500 mV beyond the supply rails) can
cause excessive current to flow in or out of the input pins. Therefore, as well as keeping the input voltage below
the maximum rating, it is also important to limit the input current to less than 10 mA. This is easily accomplished
with an input voltage resistor, as shown in Figure 4.
+5V
IOVERLOAD
10mA max
1/2
OPA2348
VOUT
VIN
5kW
Figure 4. Input Current Protection for Voltages Exceeding the Supply Voltage
10
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): OPA2348-HiRel
OPA2348-HiRel
www.ti.com
SBOS482 – NOVEMBER 2009
Rail-to-Rail Output
A class AB output stage with common-source transistors is used to achieve rail-to-rail output. This output stage is
capable of driving 5-kΩ loads connected to any potential between V+ and ground. For light resistive loads
(>100 kΩ), the output voltage can typically swing to within 18 mV from supply rail. With moderate resistive loads
(10 kΩ to 50 kΩ), the output voltage can typically swing to within 100 mV of the supply rails while maintaining
high open-loop gain (see the typical characteristic "Output Voltage Swing vs Output Current").
Capacitive Load and Stability
The OPA2348 in a unity-gain configuration can directly drive up to 250-pF pure capacitive load. Increasing the
gain enhances the amplifier’s ability to drive greater capacitive loads (see the typical characteristic "Small-Signal
Overshoot vs Capacitive Load"). In unity-gain configurations, capacitive load drive can be improved by inserting a
small (10 Ω to 20 Ω) resistor, RS, in series with the output, as shown in Figure 5. This significantly reduces
ringing while maintaining dc performance for purely capacitive loads. However, if there is a resistive load in
parallel with the capacitive load, a voltage divider is created, introducing a direct current (dc) error at the output
and slightly reducing the output swing. The error introduced is proportional to the ratio RS/RL and is generally
negligible.
V+
RS
1/2
OPA2348
VOUT
10W to
20W
VIN
RL
CL
Figure 5. Series Resistor in Unity-Gain Buffer Configuration Improves Capacitive Load Drive
In unity-gain inverter configuration, phase margin can be reduced by the reaction between the capacitance at the
op amp input and the gain setting resistors, thus degrading capacitive load drive. Best performance is achieved
by using small-valued resistors. For example, when driving a 500-pF load, reducing the resistor values from
100 kΩ to 5 kΩ decreases overshoot from 55% to 13% (see the typical characteristic "Small-Signal Overshoot
vs. Load Capacitance"). However, when large valued resistors cannot be avoided, a small (4 pF to 6 pF)
capacitor, CFB, can be inserted in the feedback, as shown in Figure 6. This significantly reduces overshoot by
compensating the effect of capacitance, CIN, which includes the amplifier's input capacitance and PC board
parasitic capacitance.
CFB
RF
RI
VIN
1/2
OPA2348
VOUT
CIN
CL
Figure 6. Improving Capacitive Load Drive
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): OPA2348-HiRel
11
OPA2348-HiRel
SBOS482 – NOVEMBER 2009
www.ti.com
Driving Analog-to-Digital Converters (ADCs)
The OPA2348 op amps are optimized for driving medium-speed sampling ADCs. The OPA2348 op amps buffer
the ADC input capacitance and resulting charge injection while providing signal gain.
Figure 7 shows the OPA2348 in a basic noninverting configuration driving the ADS7822. The ADS7822 is a
12-bit, micropower sampling converter in the MSOP-8 package. When used with the low-power miniature
packages of the OPA348, the combination is ideal for space-limited, low-power applications. In this configuration,
an RC network at the ADC input can be used to provide for anti-aliasing filter and charge injection current.
+5V
0.1µF
0.1µF
1 VREF
8 V+
DCLOCK
500W
1/2
OPA2348
+In
ADS7822
12-Bit A/D
2
VIN
–In
CS/SHDN
3
3300pF
DOUT
7
6
Serial
Interface
5
GND 4
VIN = 0 V to 5 V for
0-V to 5-V output.
NOTE: A/D Input = 0 to V REF
RC network filters high-frequency noise.
Figure 7. Noninverting Configuration Driving ADS7822
The OPA2348 can also be used in noninverting configuration driving ADS7822 in limited low-power applications.
In this configuration, an RC network at the ADC input can be used to provide for antialiasing filter and charge
injection current. See Figure 7 for the OPA2348 driving an ADS7822 in a speech bandpass filtered data
acquisition system. This small low-cost solution provides the necessary amplification and signal conditioning to
interface directly with an electret microphone. This circuit operates with VS = 2.7 V to 5 V with less than 250-μA
typical quiescent current.
V+ = +2.7V to 5V
Passband 300Hz to 3kHz
R9
510kW
R1
1.5kW
R2
1MW
R4
20kW
C3
33pF
C1
1000pF
1/2
OPA2348
Electret
Microphone(1)
R3
1MW
R6
100kΩ
R7
51kW
R8
150kW
VREF 1
8 V+
7
C2
1000pF
1/2
OPA2348
+IN
ADS7822 6
12-Bit A/D
5
2
–IN
DCLOCK
DOUT
CS/SHDN
Serial
Interface
3
4
R5
20kW
G = 100
GND
(1) Electret microphone powered by R1.
Figure 8. Speech Bandpass Filtered Data Acquisition System
12
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): OPA2348-HiRel
PACKAGE OPTION ADDENDUM
www.ti.com
1-Dec-2009
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
OPA2348CKGD4
ACTIVE
XCEPT
KGD
Pins Package Eco Plan (2)
Qty
0
1
TBD
Lead/Ball Finish
Call TI
MSL Peak Temp (3)
Call TI
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DLP® Products
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2009, Texas Instruments Incorporated