TI INA129SJD

INA128-HT, INA129-HT
www.ti.com
SBOS501C – JANUARY 2010 – REVISED APRIL 2012
PRECISION, LOW POWER INSTRUMENTATION AMPLIFIERS
Check for Samples: INA128-HT, INA129-HT
FEATURES
(1)
1
Low Offset Voltage
Low Input Bias Current: 50 nA Typ
High CMR: 95 dB Typ
Inputs Protected to ±40 V
Wide Supply Range: ±2.25 V to ±18 V
Low Quiescent Current: 2 mA Typ
•
•
•
•
APPLICATIONS
•
•
•
•
•
(1)
•
•
•
•
Controlled Baseline
One Assembly/Test Site
One Fabrication Site
Available in Extreme (–55°C/210°C)
Temperature Range (2)
Extended Product Life Cycle
Extended Product-Change Notification
Product Traceability
Texas Instruments' high temperature products
utilize highly optimized silicon (die) solutions
with design and process enhancements to
maximize performance over extended
temperatures.
司
公
限
有 2
件
技 83 器
科 16 元
子 29 子
电 -8 电
创 55 温
德 07 高
鸿 话 油
圳 电 石
深 系 理
联 代
业
专
•
•
•
•
•
•
SUPPORTS EXTREME TEMPERATURE
APPLICATIONS
Bridge Amplifier
Thermocouple Amplifier
RTD Sensor Amplifier
Medical Instrumentation
Data Acquisition
Typical values for 210°C application
(2)
Custom temperature ranges available
D, JD OR HKJ PACKAGE
(TOP VIEW)
RG
1
8
RG
V- IN
2
7
V+
V+IN
3
6
VO
V-
4
5
Ref
HKQ PACKAGE
(TOP VIEW)
RG
8
1
RG
V+
V- IN
VO
V+IN
Ref
5
V-
4
HKQ as formed or HKJ mounted dead bug
DESCRIPTION
The INA128 and INA129 are low power, general purpose instrumentation amplifiers offering excellent accuracy.
The versatile three operational amplifier design and small size make them ideal for a wide range of applications.
Current-feedback input circuitry provides wide bandwidth even at high gain.
A single external resistor sets any gain from 1 to 10,000. The INA128 provides an industry-standard gain
equation; the INA129 gain equation is compatible with the AD620.
The INA128/INA129 is laser trimmed for very low offset voltage (50 μV) and high common-mode rejection (93 dB
at G ≥ 100). It operates with power supplies as low as ±2.25 V, and quiescent current of 2 mA - typically. Internal
input protection can withstand up to ±40 V without damage.
The INA129 is available in 8-pin ceramic DIP and 8-pin ceramic surface-mount packages, specified for the –55°C
to 210°C temperature range. The INA128 is available in an 8-pin SO-8 surface-mount package, specified for the
–55°C to 175°C temperature range.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2010–2012, Texas Instruments Incorporated
INA128-HT, INA129-HT
SBOS501C – JANUARY 2010 – REVISED APRIL 2012
www.ti.com
V+
INA128:
7
50 kW
RG
G=1+
INA128, INA129
2
VIN
Over-Voltage
Protection
INA129:
A1
40 kW
1
G=1+
40 kW
(1)
49.4 kW
RG
25 kW
6
A3
RG
8
VO
司
公
限
有 2
件
技 83 器
科 16 元
子 29 子
电 -8 电
创 55 温
德 07 高
鸿 话 油
圳 电 石
深 系 理
联 代
业
专
(1)
25 kW
+
VIN
3
5
A2
Over-Voltage
Protection
40 kW
Ref
40 kW
4
V-
NOTE: (1) INA129: 24.7 kW
ORDERING INFORMATION
TA
PACKAGE
ORDERABLE PART NUMBER
TOP-SIDE MARKING
HKJ
INA129SHKJ
INA129SHKJ
HKQ
INA129SHKQ
INA129SHKQ
KGD
INA129SKGD1
NA
JD
INA129SJD
INA129SJD
D
INA128HD
128HD
–55°C to 210°C
–55°C to 175°C
BARE DIE INFORMATION
DIE THICKNESS
BACKSIDE FINISH
BACKSIDE
POTENTIAL
BOND PAD
METALLIZATION COMPOSITION
15 mils
Silicon with backgrind
GND
Al-Si-Cu (0.5%)
Origin
a
c
b
d
2
Submit Documentation Feedback
Copyright © 2010–2012, Texas Instruments Incorporated
Product Folder Link(s): INA128-HT INA129-HT
INA128-HT, INA129-HT
www.ti.com
SBOS501C – JANUARY 2010 – REVISED APRIL 2012
Table 1. Bond Pad Coordinates in Microns
DISCRIPTION
PAD NUMBER
a
b
c
d
NC
1
-57.4
-31.1
-53.3
-27
V-IN
2
-9.85
-31.4
-5.75
-27.3
V+IN
3
25.05
-31.4
29.15
-27.3
V-
4
56.2
-34.3
60.3
-30.2
Ref
5
53.75
-17.6
57.85
-11
VO
6
50.35
27.8
56.95
31.9
V+
7
7.75
30.2
11.85
34.3
司
公
限
有 2
件
技 83 器
科 16 元
子 29 子
电 -8 电
创 55 温
德 07 高
鸿 话 油
圳 电 石
深 系 理
联 代
业
专
NC
8
-57.4
28.4
-53.3
RG
9
-57.4
13.4
-53.3
20
RG
10
-57.5
2.7
-53.4
9.3
RG
11
-57.5
-7.9
-53.4
-1.3
RG
12
-57.4
-18.6
-53.3
-12
NC
RG
RG
RG
RG
32.5
NC
PAD #1
V-IN
V+
V+IN
VO
V-
Ref
Copyright © 2010–2012, Texas Instruments Incorporated
Product Folder Link(s): INA128-HT INA129-HT
Submit Documentation Feedback
3
INA128-HT, INA129-HT
SBOS501C – JANUARY 2010 – REVISED APRIL 2012
www.ti.com
ABSOLUTE MAXIMUM RATINGS (1)
over operating free-air temperature range (unless otherwise noted)
VS
VALUE
UNIT
Supply voltage
±18
V
Analog input voltage range
±40
Output short-circuit (to ground)
TA
Operating temperature
HKJ, HKQ, KGD and JD
packages
–55 to 210
D package
–55 to 175
HKJ, HKQ, KGD and JD
packages
–55 to 210
D package
–55 to 175
Storage temperature range
Lead temperature (soldering, 10s)
(1)
°C
司
公
限
有 2
件
技 83 器
科 16 元
子 29 子
电 -8 电
创 55 温
德 07 高
鸿 话 油
圳 电 石
深 系 理
联 代
业
专
TSTG
V
Continuous
°C
300
°C
Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may
degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond
those specified is not implied.
THERMAL CHARACTERISTICS FOR HKJ OR HKQ PACKAGE
over operating free-air temperature range (unless otherwise noted)
PARAMETER
θJC
MIN
TYP
to ceramic side of case
Junction-to-case thermal resistance
to top of case lid (metal side of case)
MAX
5.7
13.7
UNIT
°C/W
ELECTRICAL CHARACTERISTICS FOR INA128
TA = 25°C, VS = ±15 V, RL = 10 kΩ (unless otherwise noted)
PARAMETER
INPUT
TA = 175°C (1)
TA = –55°C to 125°C
TEST
CONDITIONS
MIN
MIN
TYP
MAX
UNIT
TYP
MAX
±25
±100/G
±125
±1000/G
±0.2
±5/G
±1
±20/G
±3.5
±80/G
µV/°C
±2
±200/G
±5
±500/G
µV/V
OFFSET VOLTAGE, RTI
Initial
TA = 25°C
vs temperature
TA = TMIN to TMAX
vs power supply
VS = ±2.25 V to
±18 V
µV
Long-term stability
±1 ±3/G
±1 ±3/G
µV/mo
Impedance, differential
1010 || 2
1010 || 2
Ω || pF
1011||9
1011||9
Ω || pF
Common mode
Common mode voltage
range (2)
VO = 0 V
(V+) − 2
(V+) − 1.4
(V−) + 2
(V−) + 1.7
Safe input voltage
(V+) − 2
(V+) − 1.4
(V−) + 2
(V−) + 1.7
±40
V
V
±40
V
VCM = ±13 V,
ΔRS = 1 kΩ
Common-mode rejection
(1)
(2)
4
G=1
58
86
58
75
G = 10
78
106
78
85
G = 100
99
125
99
110
G = 1000
113
130
113
120
dB
Minimum and maximum parameters are characterized for operation at TA = 175°C, but may not be production tested at that
temperature. Production test limits with statistical guardbands are used to ensure high temperature performance.
Input common-mode range varies with output voltage — see typical curves.
Submit Documentation Feedback
Copyright © 2010–2012, Texas Instruments Incorporated
Product Folder Link(s): INA128-HT INA129-HT
INA128-HT, INA129-HT
www.ti.com
SBOS501C – JANUARY 2010 – REVISED APRIL 2012
ELECTRICAL CHARACTERISTICS FOR INA128 (continued)
TA = 25°C, VS = ±15 V, RL = 10 kΩ (unless otherwise noted)
PARAMETER
TA = 175°C (1)
TA = –55°C to 125°C
TEST
CONDITIONS
MIN
TYP
MAX
±2
±10
MIN
TYP
UNIT
MAX
CURRENT
Bias current
vs temperature
Offset Current
±1
vs temperature
Noise voltage, RTI
f = 10 Hz
f = 100 Hz
f = 1 kHz
f = 10 Hz
f = 1 kHz
Gain equation
Range of gain
Gain error
Gain vs temperature (3)
Voltage
nA
pA/°C
10
10
nV/√Hz
8
8
nV/√Hz
8
8
nV/√Hz
0.2
0.8
µVPP
0.9
pA/√Hz
0.3
pA/√Hz
30
pAPP
1
1+
(50 kΩ/RG)
10000
1
V/V
10000
V/V
G=1
±0.01
±0.1
±0.1
G = 10
±0.02
±0.5
±0.5
±1
G = 100
±0.05
±0.7
±0.7
±1.5
G = 1000
±0.5
±2.5
±2
±4
±1
±10
±75
ppm/°C
±25
±100
±75
ppm/°C
VO = ±13.6 V,
G=1
±0.0001
±0.001
±0.008
G = 10
±0.0003
±0.002
±0.010
G = 100
±0.0005
±0.002
±0.010
±0.001
(5)
G=1
G = 1000
OUTPUT
±45
±550
1+
(50 kΩ/RG)
50-kΩ resistance (3) (4)
Nonlinearity
nA
pA/°C
G = 1000,
RS = 0 Ω
fB = 0.1 Hz to 10 Hz
GAIN
±10
±30
fB = 0.1 Hz to 10 Hz
Noise current
±550
司
公
限
有 2
件
技 83 器
科 16 元
子 29 子
电 -8 电
创 55 温
德 07 高
鸿 话 油
圳 电 石
深 系 理
联 代
业
专
NOISE
±45
±30
See
±0.6
Positive
RL = 10kΩ
(V+) − 1.4
(V+) − 0.9
(V+) − 1.4
(V+) − 0.9
Negative
RL = 10kΩ
(V−) + 1.4
(V−) + 0.8
(V−) + 1.4
(V−) + 0.8
Load capacitance stability
Short-curcuit current
±0.5
See
%
% of
FSR
(5)
V
1000
1000
pF
+6/−15
+6/−15
mA
FREQUENCY RESPONSE
Bandwidth, −3 dB
Slew rate
(3)
(4)
(5)
G=1
1300
1100
G = 10
700
700
G = 100
200
190
G = 1000
20
17.5
VO = ±10 V,
G = 10
4
4
kHz
V/µs
Specified by wafer test.
Temperature coefficient of the 50-kΩ term in the gain equation.
Nonlinearity measurements in G = 1000 are dominated by noise. Typical nonlinearity is ±0.001%.
Copyright © 2010–2012, Texas Instruments Incorporated
Product Folder Link(s): INA128-HT INA129-HT
Submit Documentation Feedback
5
INA128-HT, INA129-HT
SBOS501C – JANUARY 2010 – REVISED APRIL 2012
www.ti.com
ELECTRICAL CHARACTERISTICS FOR INA128 (continued)
TA = 25°C, VS = ±15 V, RL = 10 kΩ (unless otherwise noted)
PARAMETER
Settling time, 0.01%
Overload recovery
TA = 175°C (1)
TA = –55°C to 125°C
TEST
CONDITIONS
MIN
TYP
MAX
MIN
TYP
G=1
7
G = 10
7
7
G = 100
9
9
G = 1000
80
80
50% overdrive
4
4
MAX
UNIT
7
µs
µs
司
公
限
有 2
件
技 83 器
科 16 元
子 29 子
电 -8 电
创 55 温
德 07 高
鸿 话 油
圳 电 石
深 系 理
联 代
业
专
POWER SUPPLY
Voltage range
Current, total
±2.25
±15
±18
±18
V
±0.7
±1
±1
mA
−55
125
175
°C
−55
125
175
°C
VIN = 0 V
±2.25
±15
TEMPERATURE RANGE
Specification
Operating
ELECTRICAL CHARACTERISTICS FOR INA129
over operating free-air temperature range (unless otherwise noted)
PARAMETER
INPUT
TA = 210°C (1)
TA = –55°C to 125°C
TEST
CONDITIONS
MIN
TYP
MAX
±25
±100/G
±125
±1000/G
MIN
TYP
MAX
UNIT
OFFSET VOLTAGE, RTI
Initial
TA = 25°C
µV
vs temperature
TA = TMIN to TMAX
±0.2
±5/G
±1
±20/G
±1
±850/G
µV/°C
vs power supply
VS = ±2.25 V to
±18 V
±0.2
±20/G
±2
±200/G
±20
±1000/G
µV/V
±1 ±3/G
µV/mo
Long-term stability
±1 ±3/G
10
Impedance, differential
10
|| 2
VO = 0 V
(V+) − 2
(V+) − 1.4
(V−) + 2
(V−) + 1.7
Safe input voltage
|| 2
Ω || pF
1011||9
Ω || pF
10
1011||9
Common mode
Common mode voltage
range (2)
10
(V+) − 2
(V+) − 1.4
(V−) + 2
(V−) + 1.7
±40
V
V
±40
V
VCM = ±13 V,
ΔRS = 1 kΩ
Common-mode rejection
CURRENT
Bias current
G=1
58
86
53
G = 10
78
106
69
G = 100
99
125
89
G = 1000
113
130
95
vs temperature
Offset Current
vs temperature
(1)
(2)
6
±2
±10
±30
±1
±10
±30
dB
±50
nA
±600
pA/°C
±50
nA
±600
pA/°C
Minimum and maximum parameters are characterized for operation at TA = 210°C, but may not be production tested at that
temperature. Production test limits with statistical guardbands are used to ensure high temperature performance.
Input common-mode range varies with output voltage — see typical curves.
Submit Documentation Feedback
Copyright © 2010–2012, Texas Instruments Incorporated
Product Folder Link(s): INA128-HT INA129-HT
INA128-HT, INA129-HT
www.ti.com
SBOS501C – JANUARY 2010 – REVISED APRIL 2012
ELECTRICAL CHARACTERISTICS FOR INA129 (continued)
over operating free-air temperature range (unless otherwise noted)
TA = 210°C (1)
TA = –55°C to 125°C
TEST
CONDITIONS
PARAMETER
MIN
TYP
MAX
MIN
TYP
UNIT
MAX
NOISE
G = 1000,
RS = 0 Ω
Noise voltage, RTI
10
25
nV/√Hz
8
20
nV/√Hz
f = 1 kHz
8
20
nV/√Hz
0.2
2
µVPP
司
公
限
有 2
件
技 83 器
科 16 元
子 29 子
电 -8 电
创 55 温
德 07 高
鸿 话 油
圳 电 石
深 系 理
联 代
业
专
f = 10 Hz
f = 100 Hz
fB = 0.1 Hz to 10 Hz
Noise current
f = 10 Hz
f = 1 kHz
fB = 0.1 Hz to 10 Hz
GAIN
Gain equation
Range of gain
Gain error
Nonlinearity
OUTPUT
Voltage
pA/√Hz
0.3
pA/√Hz
30
pAPP
1+
(49.4 kΩ/RG)
1
Gain vs temperature (3)
49.4-kΩ resistance
0.9
1+
(49.4 kΩ/RG)
10000
G=1
±0.01
±0.1
1
V/V
10000
V/V
±1.1
G = 10
±0.02
±0.5
±2.6
G = 100
±0.05
±0.7
±13.5
G = 1000
±0.5
±2
±65.5
±1
±10
±100
ppm/°C
ppm/°C
G=1
(3) (4)
±25
±100
±100
VO = ±13.6 V,
G=1
±0.0001
±0.001
±0.1
G = 10
±0.0003
±0.002
±0.2
G = 100
±0.0005
G = 1000
±0.001
±0.002
±0.7
(5)
±2.4
See
Positive
RL = 10kΩ
(V+) − 1.4
(V+) − 0.9
(V+) − 1.4
(V+) − 0.9
Negative
RL = 10kΩ
(V−) + 1.4
(V−) + 0.8
(V−) + 1.4
(V−) + 0.8
Load capacitance stability
%
% of
FSR
See
(5)
V
1000
1000
pF
+6/−15
+12/−5
mA
G=1
1300
850
Short-curcuit current
FREQUENCY RESPONSE
Bandwidth, −3 dB
Slew rate
Settling time, 0.01%
Overload recovery
(3)
(4)
(5)
G = 10
700
400
G = 100
200
50
G = 1000
20
7.5
VO = ±10 V,
G = 10
4
4
G=1
7
10
G = 10
7
10
G = 100
9
30
G = 1000
80
150
50% overdrive
4
4
kHz
V/µs
µs
µs
Specified by wafer test.
Temperature coefficient of the 49.4-kΩ term in the gain equation.
Nonlinearity measurements in G = 1000 are dominated by noise. Typical nonlinearity is ±0.001%.
Copyright © 2010–2012, Texas Instruments Incorporated
Product Folder Link(s): INA128-HT INA129-HT
Submit Documentation Feedback
7
INA128-HT, INA129-HT
SBOS501C – JANUARY 2010 – REVISED APRIL 2012
www.ti.com
ELECTRICAL CHARACTERISTICS FOR INA129 (continued)
over operating free-air temperature range (unless otherwise noted)
TA = 210°C (1)
TA = –55°C to 125°C
TEST
CONDITIONS
PARAMETER
MIN
TYP
MAX
MIN
TYP
MAX
±15
±18
±2.25
±15
±18
±0.7
±0.75
UNIT
POWER SUPPLY
Voltage range
±2.25
Current, total
VIN = 0 V
±2
V
mA
TEMPERATURE RANGE
−55
Specification
125
司
公
限
有 2
件
技 83 器
科 16 元
子 29 子
电 -8 电
创 55 温
德 07 高
鸿 话 油
圳 电 石
深 系 理
联 代
业
专
Operating
−55
125
210
°C
210
°C
Estimated Life (Hours)
1000000
100000
Electromigration Fail Mode
10000
Wirebond Failure Mode
1000
110
120
130
140
150
160
170
180
190
200
210
Continuous TJ (°C)
(1)
See the data sheet for absolute maximum and minimum recommended operating conditions.
(2)
The predicted operating lifetime vs. junction temperature is based on reliability modeling using electromigration as the
dominant failure mechanism affecting device wearout for the specific device process and design characterisitics.
(3)
Wirebond lifetime is only applicable for D package.
Figure 1. INA128HD/INA129SKGD1 Operating Life Derating Chart
8
Submit Documentation Feedback
Copyright © 2010–2012, Texas Instruments Incorporated
Product Folder Link(s): INA128-HT INA129-HT
INA128-HT, INA129-HT
www.ti.com
SBOS501C – JANUARY 2010 – REVISED APRIL 2012
TYPICAL CHARACTERISTICS
At TA = 25°C, VS = ±15 V, unless otherwise noted.
GAIN
vs
FREQUENCY
COMMON-MODE REJECTION
vs
FREQUENCY
140
60
G =1000V/V
G =100V/V
G = 1000V/V
Common-Mode Rejection (dB)
50
40
30
20
G = 10V/V
10
0
G = 1V/V
− 10
− 20
G =10V/V
100
G =1V/V
80
司
公
限
有 2
件
技 83 器
科 16 元
子 29 子
电 -8 电
创 55 温
德 07 高
鸿 话 油
圳 电 石
深 系 理
联 代
业
专
Gain (dB)
G = 100V/V
120
60
40
20
0
1k
10k
100k
1M
10M
10
100
Frequency (Hz)
140
1k
10k
100k
1M
Frequency (Hz)
Figure 2.
Figure 3.
POSITIVE POWER SUPPLY REJECTION
vs
FREQUENCY
NEGATIVE POWER SUPPLY REJECTION
vs
FREQUENCY
140
Power Supply Rejection (dB)
Power Supply Rejection (dB)
G = 1000V/V
120
G =1000V/V
100
G =100V/V
80
60
G= 10V/V
40
G=1V/V
20
0
10
100
1k
10k
100k
1M
120
G =100V/V
100
80
60
40
G=10V/V
G=1V/V
20
0
10
Frequency (Hz)
Frequency (Hz)
Figure 4.
Figure 5.
Copyright © 2010–2012, Texas Instruments Incorporated
Product Folder Link(s): INA128-HT INA129-HT
Submit Documentation Feedback
9
INA128-HT, INA129-HT
SBOS501C – JANUARY 2010 – REVISED APRIL 2012
www.ti.com
TYPICAL CHARACTERISTICS (continued)
At TA = 25°C, VS = ±15 V, unless otherwise noted.
INPUT COMMON-MODE RANGE
vs
OUTPUT VOLTAGE
(VS = ±15 V)
INPUT COMMON-MODE RANGE
vs
OUTPUT VOLTAGE
(VS = ±5 V, ±2.5 V)
5
15
G ≥ 10
Common-Mode Voltage (V)
G=1
5
G=1
+15V
0
VD/2
VD/2
5
+
VO
Ref
+
VCM
-15V
10
G ≥ 10
G ≥ 10
4
10
3
G=1
2
G=1
G ≥ 10
司
公
限
有 2
件
技 83 器
科 16 元
子 29 子
电 -8 电
创 55 温
德 07 高
鸿 话 油
圳 电 石
深 系 理
联 代
业
专
Common-Mode Voltage (V)
G ≥ 10
1
0
G=1
1
2
3
VS = ±5V
VS = ±2.5V
4
5
15
-15
-10
0
-5
5
10
-5
15
-4
-3
-1
-2
Figure 7.
INPUT-REFERRED NOISE
vs
FREQUENCY
SETTLING TIME
vs
GAIN
G =10V/V
1
G =100, 1000V/V
Current Noise
1
0.1
1
10
100
1k
10k
Settling Time (ms)
¾
10
10
3
4
5
0.01%
0.1%
10
1
10
1
100
1000
Gain (V/V)
Frequency (Hz)
Figure 8.
Submit Documentation Feedback
2
100
Input Bias Current Noise (pA/√Hz)
G = 1V / V
100
10
1
Figure 6.
100
¾
Input-Referred Voltage Noise (nV/√Hz)
1k
0
Output Voltage (V)
Output Voltage (V)
Figure 9.
Copyright © 2010–2012, Texas Instruments Incorporated
Product Folder Link(s): INA128-HT INA129-HT
INA128-HT, INA129-HT
www.ti.com
SBOS501C – JANUARY 2010 – REVISED APRIL 2012
TYPICAL CHARACTERISTICS (continued)
At TA = 25°C, VS = ±15 V, unless otherwise noted.
QUIESCENT CURRENT AND SLEW RATE
vs
TEMPERATURE
INPUT OVER-VOLTAGE V/I CHARACTERISTICS
4.5
5
4
4
3.5
3
3
2
2.5
2
1
1.5
IQ
0.5
0
-55
Input Current (mA)
1.5
Slew Rate (V/µS)
Slew Rate
2
Flat region represents
normal linear operation.
-25
0
1
25
50
75
100
125
155
190
1
+15V
G=1V/V
2
3
0.5
4
0
5
210
VIN
G = 1000V/V
-50
-40
-30
-20
-10
0
IIN 15V
10
30
20
40
50
190
210
Input Voltage (V)
Figure 10.
Figure 11.
INPUT OFFSET VOLTAGE WARM-UP
INPUT BIAS CURRENT
vs
TEMPERATURE
33
8
28
6
Input Bias Current (nA)
Offset Voltage Change (mV)
G = 1V / V
0
Temperature (°C)
10
G = 1000V/V
1
司
公
限
有 2
件
技 83 器
科 16 元
子 29 子
电 -8 电
创 55 温
德 07 高
鸿 话 油
圳 电 石
深 系 理
联 代
业
专
Quiescent Current (mA)
2.5
4
2
0
-2
-4
-6
23
18
13
IB
8
3
-8
I OS
-2
-10
0
100
200
400
300
500
-50
-25
0
25
50
75
100
125
150
Temperature (°C)
Time (ms)
Figure 12.
Figure 13.
Copyright © 2010–2012, Texas Instruments Incorporated
Product Folder Link(s): INA128-HT INA129-HT
Submit Documentation Feedback
11
INA128-HT, INA129-HT
SBOS501C – JANUARY 2010 – REVISED APRIL 2012
www.ti.com
TYPICAL CHARACTERISTICS (continued)
At TA = 25°C, VS = ±15 V, unless otherwise noted.
OUTPUT VOLTAGE SWING
vs
POWER SUPPLY VOLTAGE
(V+)
(V+)-0.4
Output Voltage Swing (V)
(V+)
(V+)-0.4
(V+)-0.8
(V+)-1.2
(V-)+1.2
(V-)+0.8
(V-)+0.4
(V-)
+25°C
(V+)-0.8
(V+)-1.2
司
公
限
有 2
件
技 83 器
科 16 元
子 29 子
电 -8 电
创 55 温
德 07 高
鸿 话 油
圳 电 石
深 系 理
联 代
业
专
Output Voltage (V)
OUTPUT VOLTAGE SWING
vs
OUTPUT CURRENT
(V-)+1.2
+85°C
(V-)+0.8
(V-)
1
2
3
0
4
5
10
Figure 14.
Figure 15.
SHORT-CIRCUIT OUTPUT CURRENT
vs
TEMPERATURE
MAXIMUM OUTPUT VOLTAGE
vs
FREQUENCY
8
6
Peak-to-Peak Output Voltage (VPP)
Short-Circuit Current (mA)
10
+I SC
4
2
0
20
G =10, 100
25
G=1
G = 1000
20
15
10
5
0
-50
-25
0
25
50
75
100
125
190
210
10k
1k
Temperature (°C)
Submit Documentation Feedback
100k
1M
Frequency (Hz)
Figure 16.
12
15
Power Supply Voltage (V)
30
12
+85°C
-40 °C
-I SC
14
+25°C
-40 °C
Output Current (mA)
16
-40 °C
RL = 10 k Ω
(V-)+0.4
0
18
+85°C
Figure 17.
Copyright © 2010–2012, Texas Instruments Incorporated
Product Folder Link(s): INA128-HT INA129-HT
INA128-HT, INA129-HT
www.ti.com
SBOS501C – JANUARY 2010 – REVISED APRIL 2012
TYPICAL CHARACTERISTICS (continued)
At TA = 25°C, VS = ±15 V, unless otherwise noted.
TOTAL HARMONIC DISTORTION + NOISE
vs
FREQUENCY
SMALL SIGNAL
(G = 1, 10)
1
0.1
G=1
RL = 10kW
G=1
G =100, RL = 100kW
司
公
限
有 2
件
技 83 器
科 16 元
子 29 子
电 -8 电
创 55 温
德 07 高
鸿 话 油
圳 电 石
深 系 理
联 代
业
专
TH D + N (% )
VO = 1 V r m s
500kHz Measurement
Bandwidth
20mV/div
0.01
G =10V/V
RL = 100kW
G =1, RL = 100kW
Dashed Portion
is noise limited.
0.001
100
10k
1k
G = 10
100k
5ms/div
Frequency (Hz)
G = 10 0
20mV/div
G = 10 0 0
Figure 18.
Figure 19.
SMALL SIGNAL
(G = 100, 1000)
LARGE SIGNAL
(G = 1, 10)
G=1
5V/div
G = 10
5ms/div
20ms/div
G =100
5V/div
Figure 20.
Figure 21.
LARGE SIGNAL
(G = 100, 1000)
VOLTAGE NOISE 0.1 Hz TO 10 Hz
INPUT-REFERRED, G ≥ 100
0.1mV/div
G =1000
20ms/div
1s/div
Figure 22.
Figure 23.
Copyright © 2010–2012, Texas Instruments Incorporated
Product Folder Link(s): INA128-HT INA129-HT
Submit Documentation Feedback
13
INA128-HT, INA129-HT
SBOS501C – JANUARY 2010 – REVISED APRIL 2012
www.ti.com
APPLICATION INFORMATION
Figure 24 shows the basic connections required for operation of the INA128/INA129. Applications with noisy or
high impedance power supplies may require decoupling capacitors close to the device pins as shown.
The output is referred to the output reference (Ref) terminal which is normally grounded. This must be a lowimpedance connection to assure good common-mode rejection. A resistance of 8 Ω in series with the Ref pin will
cause a typical device to degrade.
Setting the Gain
INA128:
司
公
限
有 2
件
技 83 器
科 16 元
子 29 子
电 -8 电
创 55 温
德 07 高
鸿 话 油
圳 电 石
深 系 理
联 代
业
专
Gain is set by connecting a single external resistor, RG, between pins 1 and 8.
50 kW
G=1+ ¾
RG
INA129:
(1)
49.4 kW
G=1+ ¾
RG
(2)
Commonly used gains and resistor values are shown in Figure 24.
The 50-kΩ term in Equation 1 (49.4-kΩ in Equation 2) comes from the sum of the two internal feedback resistors
of A1 and A2. These on-chip metal film resistors are laser trimmed to accurate absolute values. The accuracy
and temperature coefficient of these internal resistors are included in the gain accuracy and drift specifications of
the INA128/INA129.
The stability and temperature drift of the external gain setting resistor, RG, also affects gain. RG’s contribution to
gain accuracy and drift can be directly inferred from Equation 2. Low resistor values required for high gain can
make wiring resistance important. Sockets add to the wiring resistance which will contribute additional gain error
(possibly an unstable gain error) in gains of approximately 100 or greater.
V+
INA129:
INA128:
G=1+
50 kW
RG
G=1+
0.1mF
49.4kW
RG
7
INA128, INA129
INA128
DESIRED
GAIN (V/V)
1
2
5
10
20
50
100
200
500
1000
2000
5000
10000
INA129
RG
(W)
NEAREST
1% RG (W)
NC
50K
12.5K
5.556K
2.632K
1.02K
505.1
251.3
100.2
50.5
25.01
10
5.001
NC
49.9K
12.4K
5.62K
2.61K
1.02K
511
249
100
49.9
24.9
10
4.99
RG
(W)
NC
49.4K
12.35K
5489
2600
1008
499
248
99
49.5
24.7
9.88
4.94
VIN
NEAREST
1% RG (W)
NC
49.9K
12.4K
5.49K
2.61K
1K
499
249
100
49.9
24.9
9.76
4.87
2
Over Voltage
Protection
A1
40kΩ
1
VO = G · (VIN+ - VIN-)
A3
RG
8
+
VIN
3
40kΩ
25kΩ(1)
6
25kΩ(1)
A2
Over Voltage
Protection
40kΩ
4
NOTE: (1) INA129: 24.7kW
40kΩ
+
Load VO
5
Ref
0.1mF
NC: No Connection
V IN
V
Also drawn in simplified form:
RG
+
V IN
INA1 28
VO
Ref
Figure 24. Basic Connections
14
Submit Documentation Feedback
Copyright © 2010–2012, Texas Instruments Incorporated
Product Folder Link(s): INA128-HT INA129-HT
INA128-HT, INA129-HT
www.ti.com
SBOS501C – JANUARY 2010 – REVISED APRIL 2012
Dynamic Performance
Figure 2 shows that, despite its low quiescent current, the INA128/INA129 achieves wide bandwidth, even at
high gain. This is due to the current-feedback topology of the input stage circuitry. Settling time also remains
excellent at high gain.
Noise Performance
The INA128/INA129 provides very low noise in most applications. Low frequency noise is approximately 2 μVPP
measured from 0.1 Hz to 10 Hz (G ≥ 100). This provides dramatically improved noise when compared to stateof-the-art chopper-stabilized amplifiers.
司
公
限
有 2
件
技 83 器
科 16 元
子 29 子
电 -8 电
创 55 温
德 07 高
鸿 话 油
圳 电 石
深 系 理
联 代
业
专
Offset Trimming
The INA128/INA129 is laser trimmed for low offset voltage and offset voltage drift. Most applications require no
external offset adjustment. Figure 25 shows an optional circuit for trimming the output offset voltage. The voltage
applied to Ref terminal is summed with the output. The operational amplifier buffer provides low impedance at
the Ref terminal to preserve good common-mode rejection.
VIN
V+
RG
INA129
VO
100mA
1/2 REF200
Ref
+
VIN
OPA177
±10mV
Adjustment Range
10kW
100W
100W
100mA
1/2 REF200
V-
(1)
OPA177 and REF200 are not tested or characterized at 210°C.
Figure 25. Optional Trimming of Output Offset Voltage
Input Bias Current Return Path
The input impedance of the INA128/INA129 is extremely high (approximately 1010 Ω). However, a path must be
provided for the input bias current of both inputs. This input bias current is approximately ±50 nA. High input
impedance means that this input bias current changes very little with varying input voltage.
Input circuitry must provide a path for this input bias current for proper operation. Figure 26 shows various
provisions for an input bias current path. Without a bias current path, the inputs will float to a potential which
exceeds the common-mode range, and the input amplifiers will saturate.
If the differential source resistance is low, the bias current return path can be connected to one input (see the
thermocouple example in Figure 26). With higher source impedance, using two equal resistors provides a
balanced input with possible advantages of lower input offset voltage due to bias current and better highfrequency common-mode rejection.
Copyright © 2010–2012, Texas Instruments Incorporated
Product Folder Link(s): INA128-HT INA129-HT
Submit Documentation Feedback
15
INA128-HT, INA129-HT
SBOS501C – JANUARY 2010 – REVISED APRIL 2012
www.ti.com
Microphone,
Hydrophone
etc.
INA129
47kW
47kW
司
公
限
有 2
件
技 83 器
科 16 元
子 29 子
电 -8 电
创 55 温
德 07 高
鸿 话 油
圳 电 石
深 系 理
联 代
业
专
Thermocouple
INA129
10kW
INA129
Center-tap provides
bias current return.
Figure 26. Providing an Input Common-Mode Current Path
Input Common-Mode Range
The linear input voltage range of the input circuitry of the INA128/INA129 is from approximately 1.4 V below the
positive supply voltage to 1.7 V above the negative supply. As a differential input voltage causes the output
voltage increase, however, the linear input range will be limited by the output voltage swing of amplifiers A1 and
A2. So the linear common-mode input range is related to the output voltage of the complete amplifier. This
behavior also depends on supply voltage (see Figure 6 and Figure 7).
Input-overload can produce an output voltage that appears normal. For example, if an input overload condition
drives both input amplifiers to their positive output swing limit, the difference voltage measured by the output
amplifier will be near zero. The output of A3 will be near 0 V even though both inputs are overloaded.
Low Voltage Operation
The INA128/INA129 can be operated on power supplies as low as ±2.25 V. Performance remains excellent with
power supplies ranging from ±2.25 V to ±18 V. Most parameters vary only slightly throughout this supply voltage
range.
Operation at very low supply voltage requires careful attention to assure that the input voltages remain within
their linear range. Voltage swing requirements of internal nodes limit the input common-mode range with low
power supply voltage. Figure 6 and Figure 7 show the range of linear operation for ±15 V, ±5 V, and ±2.5 V
supplies.
16
Submit Documentation Feedback
Copyright © 2010–2012, Texas Instruments Incorporated
Product Folder Link(s): INA128-HT INA129-HT
INA128-HT, INA129-HT
www.ti.com
SBOS501C – JANUARY 2010 – REVISED APRIL 2012
+5V
2.5V - ∆V
RG
300W
VO
INA129
Ref
2.5V + ∆V
司
公
限
有 2
件
技 83 器
科 16 元
子 29 子
电 -8 电
创 55 温
德 07 高
鸿 话 油
圳 电 石
深 系 理
联 代
业
专
Figure 27. Bridge Amplifier
-
VO
VIN
+
RG
INA129
Ref
C1
0.1mF
OPA130
R1
1MW
1
f-3dB =
2pR1C1
= 1.59 Hz
(1)
OPA130 is not tested or characterized at 210°C.
Figure 28. AC-Coupled Instrumentation Amplifier
Copyright © 2010–2012, Texas Instruments Incorporated
Product Folder Link(s): INA128-HT INA129-HT
Submit Documentation Feedback
17
INA128-HT, INA129-HT
SBOS501C – JANUARY 2010 – REVISED APRIL 2012
www.ti.com
V+
10.0V
6
REF102
R1
2
R2
4
Pt100
Cu
司
公
限
有 2
件
技 83 器
科 16 元
子 29 子
电 -8 电
创 55 温
德 07 高
鸿 话 油
圳 电 石
深 系 理
联 代
业
专
K
VO
Cu
RG
INA129
Ref
R3
100Ω = Pt100 at 0°C
ISA
TYPE
MATERIAL
+Chromel
-Constantan
+Iron
-Constantan
+Chromel
-Alumel
+Copper
-Constantan
E
J
K
T
(1)
SEEBECK
COEFFICIENT
(mV/°C)
R1, R2
58.5
66.5kW
50.2
76.8kW
39.4
97.6kW
38
102kW
REF102 is not tested or characterized at 210°C.
Figure 29. Thermocouple Amplifier With RTD Cold-Junction Compensation
-
VIN
IO =
R1
RG
INA129
V IN
·G
R1
+
Ref
IB
A1
(1)
A1
IB ERROR
OPA177
± 1.5 nA
OPA131
± 50 pA
OPA602
± 1 pA
OPA128
± 75 fA
IO
Load
OPA177, OPA131, OPA602 and OPA128 are not tested or characterized at 210°C.
Figure 30. Differential Voltage to Current Converter
18
Submit Documentation Feedback
Copyright © 2010–2012, Texas Instruments Incorporated
Product Folder Link(s): INA128-HT INA129-HT
INA128-HT, INA129-HT
www.ti.com
SBOS501C – JANUARY 2010 – REVISED APRIL 2012
RG = 5.6kW
2.8kW
G = 10
LA
RA
RG/2
INA129
VO
Ref
2.8kW
390kW
1/2
OPA2131
RL
VG
10kW
NOTE: Due to the INA129’s current-feedback
topology, VG is approximately 0.7 V less than
the common-mode input voltage. This DC offset
in this guard potential is satisfactory for many
guarding applications.
司
公
限
有 2
件
技 83 器
科 16 元
子 29 子
电 -8 电
创 55 温
德 07 高
鸿 话 油
圳 电 石
深 系 理
联 代
业
专
390kW
(1)
VG
1/2
OPA2131
OPA2131 is not tested or characterized at 210°C.
Figure 31. ECG Amplifier With Right-Leg Drive
Copyright © 2010–2012, Texas Instruments Incorporated
Product Folder Link(s): INA128-HT INA129-HT
Submit Documentation Feedback
19
PACKAGE OPTION ADDENDUM
www.ti.com
30-Apr-2012
司
公
限
有 2
件
技 83 器
科 16 元
子 29 子
电 -8 电
创 55 温
德 07 高
鸿 话 油
圳 电 石
深 系 理
联 代
业
专
PACKAGING INFORMATION
Orderable Device
INA128HD
(1)
Status
(1)
Package Type Package
Drawing
ACTIVE
SOIC
(2)
Pins
Package Qty
D
8
50
Green (RoHS
& no Sb/Br)
Eco Plan
Lead/
Ball Finish
MSL Peak Temp
(3)
Samples
(Requires Login)
CU NIPDAU Level-3-260C-168 HR
INA129SHKJ
ACTIVE
CFP
HKJ
8
25
TBD
Call TI
N / A for Pkg Type
INA129SHKQ
PREVIEW
CFP
HKQ
8
25
TBD
Call TI
Call TI
INA129SJD
ACTIVE
CDIP SB
JDJ
8
45
TBD
INA129SKGD1
ACTIVE
XCEPT
KGD
0
180
TBD
POST-PLATE N / A for Pkg Type
Call TI
N / A for Pkg Type
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF INA128-HT, INA129-HT :
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
• Enhanced Product: INA129-EP
NOTE: Qualified Version Definitions:
司
公
限
有 2
件
技 83 器
科 16 元
子 29 子
电 -8 电
创 55 温
德 07 高
鸿 话 油
圳 电 石
深 系 理
联 代
业
专
• Catalog: INA128, INA129
30-Apr-2012
• Catalog - TI's standard catalog product
• Enhanced Product - Supports Defense, Aerospace and Medical Applications
Addendum-Page 2
司
公
限
有 2
件
技 83 器
科 16 元
子 29 子
电 -8 电
创 55 温
德 07 高
鸿 话 油
圳 电 石
深 系 理
联 代
业
专
司
公
限
有 2
件
技 83 器
科 16 元
子 29 子
电 -8 电
创 55 温
德 07 高
鸿 话 油
圳 电 石
深 系 理
联 代
业
专
司
公
限
有 2
件
技 83 器
科 16 元
子 29 子
电 -8 电
创 55 温
德 07 高
鸿 话 油
圳 电 石
深 系 理
联 代
业
专
司
公
限
有 2
件
技 83 器
科 16 元
子 29 子
电 -8 电
创 55 温
德 07 高
鸿 话 油
圳 电 石
深 系 理
联 代
业
专
司
公
限
有 2
件
技 83 器
科 16 元
子 29 子
电 -8 电
创 55 温
德 07 高
鸿 话 油
圳 电 石
深 系 理
联 代
业
专
司
公
限
有 2
件
技 83 器
科 16 元
子 29 子
电 -8 电
创 55 温
德 07 高
鸿 话 油
圳 电 石
深 系 理
联 代
业
专
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
司
公
限
有 2
件
技 83 器
科 16 元
子 29 子
电 -8 电
创 55 温
德 07 高
鸿 话 油
圳 电 石
深 系 理
联 代
业
专
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
logic.ti.com
Security
www.ti.com/security
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
Audio
Amplifiers
Logic
Power Mgmt
OMAP Mobile Processors
www.ti.com/omap
Wireless Connectivity
www.ti.com/wirelessconnectivity
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated