SCAS009B − D2957, JULY 1987 − REVISED APRIL 1993
•
•
•
•
•
54ACT11520 . . . J PACKAGE
74ACT11520 . . . DW OR N PACKAGE
(TOP VIEW)
Compares Two 8-Bit Words
Inputs Are TTL-Voltage Compatible
Flow-Through Architecture Optimizes
PCB Layout
Center-Pin VCC and GND Configurations
Minimize High-Speed Switching Noise
EPICt (Enhanced-Performance Implanted
CMOS) 1-mm Process
500-mA Typical Latch-Up Immunity at 125°C
The Device Has the Equivalent of 20-kW
Pullup Resistors on Q Inputs
Package Options Include Plastic
Small- Outline Packages, Ceramic Chip
Carriers, and Standard Plastic and Ceramic
300-mil DIPs
Q1
P1
Q0
P0
GND
P=Q
G7
P7
Q6
P6
1
20
2
19
3
18
4
17
5
16
6
15
7
14
8
13
9
12
10
11
G
P2
Q2
P3
G3
VCC
P4
Q4
P5
Q5
54ACT11520 . . . FK PACKAGE
(TOP VIEW)
Q2
P3
Q3
VCC
P4
•
•
•
description
These identity comparators perform comparisons
on two 8-bit binary or BCD words. Features
include 20-kΩ pullup termination resistors on the
Q inputs for analog or switch data and a P = Q
totem-pole output.
P2
G
Q1
P1
Q0
3 2 1 20 19
18
5
17
6
16
7
15
8
14
9 10 11 12 13
Q4
P5
Q5
P6
Q6
P0
GND
P=Q
Q7
P7
The 54ACT11520 is characterized for operation
over the full military temperature range of − 55°C
to 125°C. The 74ACT11520 is characterized for
operation from − 40°C to 85°C.
4
FUNCTION TABLE
INPUTS
OUTPUT
P=Q
DATA
P, Q
ENABLE
G
P=Q
L
L
P>Q
L
H
P<Q
L
H
X
H
H
EPIC is a trademark of Texas Instruments Incorporated.
Copyright 1993, Texas Instruments Incorporated
!"# $ %&'# "$ (&)*%"# +"#',
+&%#$ %! # $('%%"#$ (' #-' #'!$ '."$ $#&!'#$
$#"+"+ /""#0, +&%# (%'$$1 +'$ # '%'$$"*0 %*&+'
#'$#1 "** (""!'#'$,
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77001
•
2−1
SCAS009B − D2957, JULY 1987 − REVISED APRIL 1993
logic symbol†
G
P0
P1
P2
P3
P4
P5
P6
P7
Q0
Q1
Q2
Q3
Q4
Q5
Q6
Q7
20
4
2
logic diagram (positive logic)
COMP
G1
P7
0
Q7
19
P6
17
P
14
Q6
12
10
8
3
1
P5
7
1P = Q
6
Q5
P=Q
0
P4
18
16
Q4
Q
13
11
P3
9
7
Q3
7
† This symbol is in accordance with ANSI/IEEE Std 91-1984
and IEC Publication 617-12.
P2
Q2
P1
Q1
P0
Q0
G
8
7
10
9
12
11
14
13
17
6
16
19
18
2
1
4
3
20
Pin numbers shown are for the DW, J, and N packages.
schematic of Q inputs
VCC
Input
GND
2−2
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77001
•
P=Q
SCAS009B − D2957, JULY 1987 − REVISED APRIL 1993
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V
Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to VCC + 0.5 V
Output voltage range, VO (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to VCC + 0.5 V
Input clamp current, IIK (VI < 0 or VI > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 20 mA
Output clamp current, IOK (VO < 0 or VO > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 50 mA
Continuous output current, IO (VO = 0 to VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 50 mA
Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±100 mA
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
recommended operating conditions
54ACT11520
NOM
MAX
MIN
NOM
MAX
4.5
5
5.5
4.5
5
5.5
VCC
VIH
Supply voltage
VIL
VI
Low-level input voltage
Input voltage
0
VO
IOH
Output voltage
0
IOL
Dt /Dv
Low-level output current
TA
Operating free-air temperature
High-level input voltage
74ACT11520
MIN
2
2
0.8
High-level output current
VCC
VCC
0
0
−24
24
Input transition rise or fall rate
•
V
V
0.8
V
VCC
VCC
V
−24
mA
V
24
mA
0
10
0
10
ns/ V
−55
125
−55
85
°C
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77001
•
UNIT
2−3
SCAS009B − D2957, JULY 1987 − REVISED APRIL 1993
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
IOH = − 50 mA
A
VOH
IOH = − 24 mA
IOH = − 50 mA{
IOH = − 75 mA{
MIN
4.4
4.4
4.4
5.5 V
5.4
5.4
5.4
4.5 V
3.94
3.7
3.8
5.5 V
4.94
4.7
4.8
MAX
V
0.1
0.1
5.5 V
0.1
0.1
0.1
4.5 V
0.36
0.5
0.44
5.5 V
0.36
0.5
0.44
IIH
IIL
VI = VCC, Q inputs only
VI = GND, Q inputs only
5.5 V
II
VI = VCC or GND, P and G inputs only
Q inputs at GND,
Other inputs VI = VCC or GND
5.5 V
0.1
1.65
10
10
10
mA
− 0.6
−1
−1
mA
± 0.1
±1
±1
mA
4.8
8
8
mA
5.5 V
8
160
80
mA
5.5 V
0.9
1
1
mA
5.5 V
Q inputs open,
One input at 3.4 V and other inputs at
VCC or GND, P and G inputs only
VI = VCC or GND
V
1.65
5.5 V
Q inputs at open,
Other inputs VI = VCC or GND
UNIT
3.85
4.5 V
IOL = 24 mA
MAX
3.85
5.5 V
5.5 V
DICC}
74ACT11520
MIN
4.5 V
IOL = 50 mA{
IOL = 75 mA{
ICC
54ACT11520
MIN
5.5 V
IOL = 50 mA
A
VOL
TA = 25°C
TYP
MAX
VCC
− 0.3
5.5 V
2.3
Ci
5V
3.5
† Not more than one output should be tested at a time, and the duration of the test should not exceed 10 ms.
‡ This is the increase in supply current for each input that is at one of the specified TTL voltage levels rather than 0 V or VCC.
pF
switching characteristics over recommended ranges of supply voltage and operating free-air
temperature (unless otherwise noted) (see Figure 1)
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
tPLH
tPHL
P or Q
P=Q
tPLH
tPHL
G
P=Q
MIN
TA = 25°C
TYP
MAX
54ACT11520
74ACT11520
MIN
MAX
MIN
MAX
1.5
8.6
12.7
1.5
15.4
1.5
14.3
1.5
8
12.4
1.5
14.8
1.5
13.9
1.5
6.4
8.5
1.5
10.2
1.5
9.5
1.5
5.8
9
1.5
10.4
1.5
9.8
UNIT
ns
ns
operating characteristics, VCC = 5 V, TA = 25°C
PARAMETER
Cpd
2−4
TEST CONDITIONS
Power dissipation capacitance
CL = 50 pF,
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77001
•
f = 1 MHz
TYP
UNIT
40
pF
SCAS009B − D2957, JULY 1987 − REVISED APRIL 1993
PARAMETER MEASUREMENT INFORMATION
3V
Input
(see Note B)
From Output
Under Test
CL = 50 pF
(see Note A)
1.5 V
1.5 V
0V
tPHL
500 Ω
tPLH
50% VCC
Output
VOH
50% VCC
VOL
VOLTAGE WAVEFORMS
LOAD CIRCUIT
NOTES: A. CL includes probe and jig capacitance.
B. Input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr = 3 ns, tf = 3 ns.
C. The outputs are measured one at a time with one input transition per measurement.
Figure 1. Load Circuit and Voltage Waveforms
TYPICAL CHARACTERISTICS
Q INPUT CURRENT
vs
INPUT VOLTAGE
0
VCC = 5 V
TA = 25°C
IIII − Input Current − µuA
A
− 50
− 100
− 150
− 200
− 250
− 300
0
1
3
4
2
VI − Input Voltage − V
5
6
Figure 2
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77001
•
2−5
SCAS009B − D2957, JULY 1987 − REVISED APRIL 1993
2−6
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77001
•
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DLP® Products
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2009, Texas Instruments Incorporated