NFS110 Series Single and quad output LOW TO MEDIUM POWER AC/DC POWER SUPPLIES • • • • • • • 80-110W AC/DC Universal Input Switch Mode Power Supplies 1 7.0 x 4.25 x 1.8 inch package Overvoltage and short circuit protection 110W with 20CFM Adjustable outputs EN55022, EN55011 conducted emissions level B UL, VDE and CSA safety approvals CE mark The NFS110 series is a 110W universal input AC/DC power supply on a 7 x 4.25 inch card. The NFS110 series has four single and three quad output models and has proven itself to be highly reliable and versatile product for a wide range of communication and industrial applications, with a very high peak current capability on each output for drive and motor applications. The NFS110 provides 80W of output power with free air convection cooling which can be boosted to 110W with 20CFM of air. Standard features include overvoltage and short circuit protection. The series, with full international safety approval and the CE mark, meets conducted emissions EN55022 level B. The NFS110 series is designed for use in low power data networking, computer, telecom and industrial applications such as servers, thermal printers, storage devices, vending machines and POS equipment. 2 YEAR WARRANTY SPECIFICATIONS All specifications are typical at nominal input, full load at 25°C unless otherwise stated OUTPUT SPECIFICATIONS GENERAL SPECIFICATIONS Voltage adjustability +5.1V output on multi’s 5.1V single output 12V single output 15V single output 24V single output ±3.0% ±3.0% 12V to 14V 15V to 18V 24V to 30V Line regulation LL to HL, FL All outputs on all units ±0.1% max. Overshoot/undershoot At turn-on 0% Temperature coefficient All outputs ±0.02%/°C Overvoltage protection Multi output 5.1V only 5.1V single 12V single 15V single 24V single Output power limit Minimum output current Primary power limited 6.25V±0.75V 6.25V±0.75V 15.75V±1.0V 22V±1.5V 33V±2.5V Pin max. 160W Pout min. 110W (See Note 13) Short circuit protection Hold-up time 110VAC 110VAC 230VAC 230VAC Efficiency Multiple outputs +5.1V single 12V and 15V singles 24V single Isolation voltage Input/output Input/chassis Switching frequency At 100 Watts output At zero load Approvals and standards (See Note 12) 80W 110W 80W 110W 35ms 17ms 140ms 100ms 70% 70% 72% 75% typical typical typical typical 3000VAC 1500VAC 20 to 70kHz 100 to 250kHz VDE0805, EN60950, IEC950 IEC1010, UL1950 CSA C22.2 No. 950 Weight Singles Multiple outputs 550g (19.4oz) 600g (21.2oz) MTBF (See Note 9) MIL-HDBK-217E 125,000 hours 0A Burst mode operation @ @ @ @ ENVIRONMENTAL SPECIFICATIONS INPUT SPECIFICATIONS Input voltage range 85 to 264VAC 120 to 370VDC Input frequency range 47Hz to 440Hz Input surge current 230VAC Safety ground leakage current 110VAC, 50Hz 230VAC, 50Hz Thermal performance (See Notes 9, 10) Operating, see curve 0°C to +70°C Non-operating –40°C to +85°C 0°C to +50°C, 80W amb. convection cooled +50°C to +70°C, Derate 2W/°C amb. convection cooled 0°C to +50°C, 110W 20CFM forced air +50°C to +70°C, Derate 20CFM forced air 2.75W/°C Peak, 0°C to +50°C, 110W max. 60 seconds Relative humidity Non-condensing Altitude Operating Non-operating Vibration (See Note 11) 5Hz to 500Hz 35A 0.2mA, max. 0.4mA, max. EMC CHARACTERISTICS Conducted emissions Radiated emissions ESD air ESD contact Surge Fast transients Radiated immunity Conducted immunity EN55022, FCC part 15 EN55022, FCC part 15 EN61000-4-2, level 3 EN61000-4-2, level 4 EN61000-4-5, level 3 EN61000-4-4, level 3 EN61000-4-3, level 3 EN61000-4-6, level 3 Perf. Perf. Perf. Perf. Perf. Perf. Level B Level A criteria 1 criteria 1 criteria 1 criteria 1 criteria 2 criteria 1 5% to 95% RH 10,000 feet max. 40,000 feet max. 2.4G approx. File Name: NFS110.PDF Rev: 01 Jan 2000 NFS110 Series Single and quad output LOW TO MEDIUM POWER AC/DC POWER SUPPLIES 80-110W AC/DC Universal Input Switch Mode Power Supplies 2 For the most current data and application support visit www.artesyn.com/powergroup/products.htm OUTPUT VOLTAGE +5.1V OUTPUT CURRENTS MAX (1) 8.0A PEAK (2) 20.0A FAN (3) 10.0A 5 6 7 8 9 10 11 12 13 TOTAL REGULATION 50mV 4.5A 9.0A 5.0A 120mV ±3.0% 0.5A 1.5A 1.0A 120mV ±3.0% –5.0V 0.5A 1.5A 1.0A 50mV ±3.0% +5.1V (IA) 8.0A 20.0A 10.0A 50mV ±2.0% (6) MODEL NUMBERS (5) ±2.0% –12.0V 3.5A 4.5A 4.5A 240mV +10/–5.0% +12.0V 4.5A 9.0A 5.0A 120mV ±3.0% –12.0V 0.5A 1.5A 1.0A 120mV ±3.0% +5.1V 8.0A 20A 10A 50mV ±2.0% NFS110-7602P (6) NFS110-7604P 4.0A 7.5A 5A 150mV ±3.0% –15.0V 0.5A 1.5A 1.0A 150mV ±3.0% –5.0V 0.5A 1.5A 1.0A 50mV ±3.0% 5.1V 16.0A 22.0A 20.0A 50mV ±2.0% NFS110-7605 (7,8) 12V 7.0A 9.0A 9.0A 120mV ±2.0% NFS110-7612 (7,8) 15V 5.0A 7.3A 7.3A 150mV ±2.0% NFS110-7615 (7,8) 24V 3.5A 4.5A 4.5A 240mV ±2.0% NFS110-7624 (7,8) Convection cooled, 80W maximum. Peak outputs lasting less than 60 seconds with duty cycle less than 10%. Total peak power must not exceed 110W. Forced air, 20CFM at 1 atmosphere, 110W maximum. Figure is peak-to-peak. Output ripple is measured across a 50MHz bandwidth using a 12 inch twisted pair terminated with a 47µF capacitor. Total regulation is defined as the static output regulation at 25°C, including initial tolerance, line voltage within stated limits and output voltages adjusted to their factory settings. To achieve stated regulation on the 24V output on the NFS110-7602P, the following load condition must be true: IA / IB ≤ 5, where: IA = +5.1V output current, and IB = +24V output current The +24V output will maintain ±5.0% regulation under the following additional condition: IA ≤ 5A. Single output models have floating outputs which may be referenced as either positive or negative. Higher voltage supplies may be adjusted over a wide output voltage range, as long as the total output power does not exceed 80 Watts (natural convection) or 110 Watts (forced air). Power fail detect not available on single output models. Derating curve is application specific for ambient temperatures >50°C, for optimum reliability no part of the heatsink should exceed 90oC and no semiconductor case temperature should exceed 100oC. Caution: Allow a minimum of 1 second after disconnecting the power when making thermal measurements. Three orthogonal axes, random vibration, 10 minute test for each axis. This product is only for inclusion by professional installers within other equipment and must not be operated as a stand alone product. Artesyn Technologies recommends a minimum load of 11W to achieve the design MTBF. See the derating curve on page 3. (F) NFS110-7601P +15.0V Notes 3 4 (4) +12.0V +24.0V (IB) 1 2 RIPPLE TRANSIENT RESPONSE NFS110-7601P +5.1V (7.5A to 10A) +12V (2.5A to 5A) -12V (0.5A to 1A) -5V (0.5A to 1A) NFS110-7602P +5.1V (7.5A to 10A) +24V (1.5A to 3A) +12V (2.5A to 5A) -12V (0.5A to 1A) NFS110-7604P +5.1V (7.5A to 10A) +15V (2.5A to 5A) -15V (0.5A to 1A) -5V (0.5A to 1A) 150mV peak, 1ms recovery 100mV peak, 0.5ms recovery 100mV peak, 0.5ms recovery 100mV peak, 0.5ms recovery 150mV peak, 1ms recovery 300mV peak, 1ms recovery 100mV peak, 0.5ms recovery 100mV peak, 0.5ms recovery 150mV peak, 1ms recovery 100mV peak, 0.5ms recovery 100mV peak, 0.5ms recovery 100mV peak, 0.5ms recovery NFS110-7605 +5.1V (10A to 20A) 250mV peak, 1ms recovery NFS110-7612 +12V (4.5A to 9A) 360mV peak, 1ms recovery NFS110-7615 +15V (3.65A to 7.3A) 450mV peak, 1ms recovery NFS110-7624 +24V (2.25A to 4.5A) 720mV peak, 1ms recovery www.artesyn.com File Name: NFS110.PDF Rev: 01 Jan 2000 NFS110 Series Single and quad output LOW TO MEDIUM POWER AC/DC POWER SUPPLIES 80-110W AC/DC Universal Input Switch Mode Power Supplies 3 For the most current data and application support visit www.artesyn.com/powergroup/products.htm AC (J1) mating connector Power fail detect signal (Note 8) OPTIONAL POWER FAIL DETECT TIMING DIAGRAM Molex 09-50-3051 or Molex 09-91-0500 mating connector with 2478 or equivalent crimp terminals. 5V OUTPUT DC (J2) mating connector 4.75V 4.75V HIGH Molex 09-50-3131 or Molex 09-91-1300 mating connector with 2478 or equivalent crimp terminals. 50ms≤T1≤200ms T2 will vary with line and load T3≥3ms Pout: 110W PFD output is an open collector which will sink ≤40mA in the low state. AC INPUT 3.5V MIN LOW PFD SIGNAL 0-0.4 MAX T3 T2 T1 0.475 ±0.010 (12.07) DERATING CURVE (See Notes 9, 10) Output Power (Watts) 1.00 ±0.005 (25.4) 1.80 (45.72) MAX 110W 20 CFM FORCED AIR COOLING 80W 0.050 ±0.020 (1.27) 3.35 ±0.015 (85.09) 6-32 UNC (4PL) 1.55 ±0.005 (39.37) PIN 1 Voltage Adjust Optional Power Fail Detect Circuit (Key = Pin 2) 4.250 ±0.020 (107.95) NATURAL CONVECTION COOLING J2 55W 40W T1 T1 3.750 ±0.005 (95.25) Pin 1 PIN 1 L1 J1 C6 F1 0.250 ±0.010 (6.35) 6.50 ±0.005 (165.1) 0.156 DIA. HOLE (4PL) 11W 11W MINIMUM LOAD REQUIRED AT 230VAC 0W 0°C 10°C 20°C 30°C 40°C 50°C 60°C 70°C 5A, 250 VAC 7.00 ±0.020 (177.8) 0.250 ±0.010 (6.35) ALL DIMENSIONS IN INCHES (mm) PIN CONNECTIONS J1 –7601P –7602P –7604P SINGLES Mechanical Notes Pin 1 AC Ground AC Ground AC Ground AC Ground A Metallic or non-metallic stand-offs (maximum diameter 5.4mm) can be used in all four mounting holes without effecting safety approval. B The ground pad of the mounting hole near J1, allows system grounding through a metal stand-off to the system chassis. C The heat sink is grounded, and allows system grounding by mechanical connection to the system chassis. D The supply must be mechanically supported using the PCB mounting holes and may be additionally supported by the heatsink mounting holes. E It is always advisable to attach the power supply heat sink to another thermal dissipator (such as a chassis or finned heatsink etc). The resulting decrease in heat sink mounted component temperatures will improve power supply lifetime. F A standard L-bracket and cover is available for mounting which contains all screws, connectors and necessary mounting hardware. Two different kits are available, order part number ‘NFS110 COVER KIT’ or ‘NFS110C’. Pin 2 AC Neutral AC Neutral AC Neutral AC Neutral Pin 3 AC Line AC Line AC Line AC Line Pin 1 +5.1V +5.1V +5.1V Vout Pin 2 +5.1V +5.1V +5.1V Vout International Safety Standard Approvals J2 Pin 3 +5.1V +5.1V +5.1V Vout Pin 4 Return Return Return Return Pin 5 Return Return Return Return Pin 6 Return Return Return Return Pin 7 Return Return Return Return Pin 8 +12V +12V +15V Vout Pin 9 +12V +12V +15V Vout Pin 10 PFD PFD PFD N/C Pin 11 –12V –12V –15V N/C VDE0805/EN60950/IEC950/IEC1010 File No. 10401-3336-1049 Licence No. 2874, 1653 and 1049 Pin 12 UL1950 File No. E136005 Pin 13 CSA C22.2 No. 950 File No. LR41062C Removed for Key –5V +24V –5V N/C N/C = no connection. Data Sheet © Artesyn Technologies® 2002 The information and specifications contained in this data sheet are believed to be correct at time of publication. However, Artesyn Technologies accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. No rights under any patent accompany the sale of any such product(s) or information contained herein. www.artesyn.com File Name: NFS110.PDF Rev: 01 Jan 2000