7MBP100TEA060 600V / 100A 7 in one-package Econo IPM series Features · Temperature protection provided by directly detecting the junction temperature of the IGBTs · Low power loss and soft switching · High performance and high reliability IGBT with overheating protection · Higher reliability because of a big decrease in number of parts in built-in control circuit Maximum ratings and characteristics Absolute maximum ratings(at Tc=25°C unless otherwise specified) Item Bus voltage DC Surge Short operating Collector-Emitter voltage *1 Collector current Inverter DC 1ms Duty=72.3% *2 Collector power dissipation One transistor *3 Collector current DC 1ms Forward current diode Collector power dissipation One transistor *3 Supply voltage of Pre-Driver *4 Input signal voltage *5 Input signal current Alarm signal voltage *6 Alarm signal current *7 Junction temperature Operating case temperature Storage temperature Solder temperature *8 Isolating voltage (Terminal to base, 50/60Hz sine wave 1min.) Screw torque Mounting (M5) Symbol Rating Min. Max. VDC 0 0 200 0 -0.5 -0.5 -0.5 -20 -40 - VDC(surge) V SC VCES IC ICP -IC PC IC ICP IF PC V CC Vin Iin VALM IALM Tj Topr Tstg Tsol Viso 450 500 400 600 100 200 100 347 50 100 50 198 20 Vcc+0.5 3 Vcc 20 150 100 125 260 AC2500 3.5 Unit V V V V A A A W A A A W V V mA V mA °C °C °C °C V N·m Note *1 : Vces shall be applied to the input voltage between terminal P and U or ‚u or W, N and U or V or W *2 : 125°C/FWD Rth(j-c)/(Ic x VF MAX)=125/0.665/(100 x 2.6) x 100=72.3% *3 : Pc=125°C/IGBT Rth(j-c)=125/0.36=347W [Inverter] Pc=125°C/IGBT Rth(j-c)=125/0.63=198W [Breake] *4 : VCC shall be applied to the input voltage between terminal No.4 and 1, 8 and 5, 12 and 9, 14 and 13 *5 : Vin shall be applied to the input voltage between terminal No.3 and 1, 7 and 5, 11 and 9, 16,17,18 and 13. *6 :VALM shall be applied to the voltage between terminal No.2 and 1, No6 and 5, No10 and 9, No.19 and 13. *7 : IALMshall be applied to the input current to terminal No.2,6,10 and 19. *8 : Immersion time 10±1sec. 7MBP100TEA060 IGBT-IPM Electrical characteristics (at Tc=Tj=25°C, Vcc=15V unless otherwise specified.) Main circuit Inverter Item Collector current at off signal input Collector-Emitter saturation voltage Forward voltage of FWD Brake Collector current at off signal input Collector-Emitter saturation voltage Forward voltage of Diode Turn-on time Turn-off time Reverse recovery time Maximum Avalanche Energy (A non-repetition) Symbol ICES VCE(sat) VF ICES VCE(sat) VF ton toff trr PAV Condition Min. VCE=600V Vin terminal open. Ic=100A Terminal Chip -Ic=100A Terminal Chip VCE=600V Vin terminal open. Terminal Ic=50A Chip Terminal -Ic=50A Chip VDC=300V,Tj=125°C IC=100A Fig.1, Fig.6 VDC=300V, IC=100A Fig.1, Fig.6 Internal wiring inductance=50nH Main circuit wiring inductace=54nH Typ. 1.2 100 Max. 1.8 1.6 1.75 1.9 - Unit 1.0 2.3 2.6 1.0 2.2 3.3 3.6 0.3 - mA V V mA V V µs mJ Control circuit Item Supply current of P-line side pre-driver(one unit) Supply current of N-line side pre-driver Input signal threshold voltage (on/off) Symbol Iccp ICCN Vin(th) Input zener voltage Alarm signal hold time VZ tALM Current limit resistor RALM Condition Switching Trequency : 0 to 15kHz Tc=-20 to 125°C Fig.7 ON OFF Rin=20k ohm Tc=-20°C Fig.2 Tc=25°C Fig.2 Tc=125°C Fig.2 Alarm terminal Min. Typ. Max. 18 65 1.00 1.35 1.70 1.25 1.60 1.95 8.0 1.1 2.0 4.0 1425 1500 1575 Unit mA mA V V V ms ms ms ohm Protection Section ( Vcc=15V) Item Over Current Protection Level of Inverter circuit Over Current Protection Level of Brake circuit Over Current Protection Delay time SC Protection Delay time IGBT Chip Over Heating Over Heating Protection Hysteresis Under Voltage Protection Level Under Voltage Protection Hysteresis Symbol IOC IOC tDOC tSC TjOH TjH V UV VH Condition Min. 150 75 150 11.0 0.2 Tj=125°C Tj=125°C Tj=125°C Tj=125°C Fig.4 Surface of IGBT chips Typ. 5 20 0.5 Max. 8 - 12.5 - Thermal characteristics( Tc=25°C) Item Junction to Case thermal resistance *9 Inverter Brake IGBT FWD IGBT Case to fin thermal resistance with compound Symbol Rth(j-c) Rth(j-c) Rth(j-c) Rth(c-f) Min. - Typ. 0.05 Max. 0.36 0.665 0.63 Unit °C/W °C/W °C/W - °C/W Min. Typ. Max. Unit *9 For 1device, Case is under the device Noise Immunity ( VDC=300V, Vcc=15V, Test Circuit Fig.5) Item Common mode rectangular noise Common mode lightning surge Condition Pulse width 1µs, polarity ±,10minuets Judge : no over-current, no miss operating Rise time 1.2µs, Fall time 50µs Interval 20s, 10 times Judge : no over-current, no miss operating ±2.0 - - kV ±5.0 - - kV Symbol V DC V CC - Min. 13.5 2.5 Typ. 15.0 - Max. 400 16.5 3.0 Unit V V Nm Symbol Wt Min. - Typ. 270 Max. - Unit g Recommendable value Item DC Bus Voltage Operating Supply Voltage of Pre-Driver Screw torque (M5) Weight Item Weight Unit A A µs µs °C °C V V 7MBP100TEA060 IGBT-IPM Vin(th) Vin On Vin(th) trr 90% 50% Ic 90% 10% toff ton Figure 1. Switching Time Waveform Definitions ) on on Gate On Vge (Inside IPM ) Fault (Inside IPM off off /Vin Gate Off normal alarm /ALM tALM > Max. 1 tALM > t ALM 2ms(typ.) 3 Max. 2 Fault : Over-current,Over-heat or Under-voltage Figure 2. Input/Output Timing Diagram tsc Ic Ic Ic I ALM I ALM I ALM Figure.4 Definition of tsc Vcc PP IPM IPM 20 k DC 15V VccU 20k DC 15V VinU SW1 P IPM DC 15V SW2 Earth GND GND N Ic AC200V V Vcc VinX DC 300V U GNDU 20k + + Vin HCPL 4504 CT L Figure 6. Switching Characteristics Test Circuit + W Icc A 4700p N Cooling Fin Vcc P Noise DC 15V IPM U Vin V P.G +8V fsw W GND N Figure 5. Noise Test Circuit Figure 7. Icc Test Circuit 7MBP100TEA060 IGBT-IPM Block diagram P VccU 4 VinU 3 Pre- Driver ALMU 2 RALM 1.5k Vz GNDU 1 VccV 8 VinV 7 U Pre- Driver ALMV 6 RALM 1.5k Vz GNDV 5 VccW 12 VinW 11 ALMW 10 V Pre- Driver RALM 1.5k Vz GNDW 9 Vcc 14 VinX 16 W Pre- Driver Vz GND VinY 13 17 Pre- Driver Vz VinZ Pre-drivers include following functions 1.Amplifier for driver 18 Pre- Driver Vz 2.Short circuit protection 3.Under voltage lockout circuit B VinDB 15 ALM 19 4.Over current protection 5.IGBT chip over heating protection Pre- Driver RALM 1.5k Vz N MBCFM Outline drawings, mm Mass : 270g 7MBP100TEA060 IGBT-IPM Characteristics Control circuit characteristics (Respresentative) Input signal thresh old voltage vs. P ower sup ply voltag e P ower sup ply current vs. Switching frequency Tc=1 25°C 2 .5 P-sid e N-sid e 50 V cc=17V V cc=15V V cc=13V 40 30 20 V cc=17V V cc=15V V cc=13V 10 Inpu t sig nal thres hold voltag e : Vin (on),Vin (off) (V) Pow er su p ply c urre nt : Icc (m A) 60 0 2 } Vin(off) } Vin(on) 1 .5 1 0 .5 0 0 5 10 15 20 12 25 Switch in g freq u en cy : fs w (kHz) 18 1 Un de r volta ge h ys teris is : VH (V) Und er voltag e : VUVT (V) 13 14 15 16 17 Power su p p ly voltag e : Vcc (V) Un d er voltag e h ysterisis vs. Jn ction tem p erature Under voltage vs. Junction temp erature 14 12 10 8 6 4 2 0 0 .8 0 .6 0 .4 0 .2 0 20 40 60 80 100 12 0 Ju nc tion te m pe ra tu re : Tj (°C) 140 20 40 60 80 100 12 0 140 Ju n ction tem peratu re : Tj(°C) Over heatin g characteristics TjOH,TjH vs. Vcc Alarm hold tim e vs. P ower sup ply voltag e 3 20 0 O ver he atin g p rotection : TjO H (°C) O H h y ste risis : Tj H (°C) Alarm hold time : tALM (m Se c) Tj=25°C Tj= 12 5°C 2 .5 Tc= 10 0° C 2 Tc=25°C 1 .5 1 0 .5 0 TjO H 15 0 10 0 50 TjH 0 12 13 14 15 16 17 Power su p p ly voltag e : Vcc (V) 18 12 13 14 15 16 17 Power su p p ly voltag e : Vcc (V) 18 7MBP100TEA060 IGBT-IPM Main circuit characteristics (Respresentative) Col lector cu rren t vs. Coll ec to r-Emitter voltag e Tj=25°C(Ch ip) Vc c= 15V Collector Cu rre nt : Ic (A) 12 0 10 0 V cc= 17V 80 V cc=13V 60 40 20 0 0 0 .5 1 1.5 2 2.5 3 Co llector-Em itte r vo ltage : Vce (V) Col lector cu rren t vs. Collec tor-Emitter voltag e Tj=125°C(Ch ip ) Vc c= 15V 12 0 V cc= 17V 10 0 Vc c= 15V 12 0 Collec tor Cu rre nt : Ic (A) Collector Cu rre nt : Ic (A) Col lector cu rren t vs. Collec tor-Emitter voltag e Tj=125°C (Term in al) V cc=13V 80 60 40 20 10 0 V cc=17V V c c= 13V 80 60 40 20 0 0 0 0 .5 1 1.5 2 2.5 3 0 Co llector-Em itter vo lta g e : Vce (V) 0 .5 1 1.5 2 2.5 3 Collector-Em itter vo lta g e : Vce (V) Forward current vs. Forward voltage (Term inal) Forward current vs. Forward voltage (Chip) 15 0 15 0 12 5°C Fo rw ard Cu rren t : If (A) Fo rw ard Curren t : If (A) 12 5° C 2 5°C 10 0 50 0 2 5° C 10 0 50 0 0 0.5 1 1.5 Fo rw ard vol ta ge : Vf (V) 2 2 .5 0 0.5 1 1.5 Fo rw ard vol ta ge : Vf (V) 2 2 .5 7MBP100TEA060 IGBT-IPM 10 8 6 Eon 4 Eoff 2 Switching Loss vs. Collector Current Edc=300V,V cc=15V,Tj=1 25°C Switch in g los s : Eo n,Eo ff,Err (m J/cy cl e) Switch in g los s : Eo n,Eo ff,Err (m J/cy cl e) Switching Loss vs. Collector Current Edc=30 0V,Vcc=15 V,Tj=25°C E rr 0 10 Eon 8 6 4 Eoff 2 E rr 0 0 20 40 60 80 10 0 120 0 20 Collector cu rren t : Ic (A) 40 60 80 10 0 120 Collec tor cu rren t : Ic (A) Th erm al resista n ce : Rth (j-c) (°C /W ) Transient therm al resistance 1 FWD IG BT 0 .1 0.01 0.00 1 0.0 1 0 .1 1 Pu lse width :Pw (sec) Power derating for FW D (per device) Power d eratin g for IG BT (per device) 25 0 Co lle cter Power D issip ation : P c (W ) Collecter P owe r Dissip ation : Pc (W ) 40 0 35 0 30 0 25 0 20 0 15 0 10 0 50 0 20 0 15 0 10 0 50 0 0 20 40 60 80 100 12 0 14 0 160 Case Tem p eratu re : Tc (°C) 0 20 40 60 80 100 12 0 14 0 160 Case Tem p eratu re : Tc (°C) 7MBP100TEA060 IGBT-IPM Switching tim e vs. Collector current Edc=30 0V,Vcc=15 V,Tj=25°C Switching tim e vs. Collector current Edc=300 V,V cc=15V,Tj=1 25°C 10 00 0 S witch in g tim e : ton ,toff,tf (n Sec) S witch in g tim e : to n,toff,tf (nSec) 10 00 0 ton toff 1 00 0 10 0 tf 10 toff 1 00 0 10 0 tf 10 20 40 60 80 100 120 140 160 Reverse recovery characteristics trr,Irr vs.IF trr125°C trr2 5° C 10 0 Irr125°C Irr2 5° C 10 1 20 40 60 80 100 120 Fo rw ard cu rren t:IF(A) 20 40 60 80 100 120 Col lector cu rren t : Ic (A) Col lector cu rren t : Ic (A) R eve rse rec overy cu rren t:Irr(A) Reverse re covery time:trr(nsec) ton 140 160 140 160 7MBP100TEA060 IGBT-IPM Characteristics Dynamic Brake Characteristics (Respresentative) Collector current vs. Collector-Em itter voltage Tj=25°C 80 V cc=15V Vc c= 17V Co llector Current : Ic (A) Coll ec to r Cu rre nt : Ic (A) 80 60 V cc=13V 40 20 0 0 .5 1 1.5 2 2.5 3 Co llector-Em itter vo lta g e : Vce (V) V cc= 17V 60 V cc=13V 40 20 1 IG B T 0 .1 0.01 0.00 1 0.0 1 0 .1 1 Pu lse width :Pw (sec) Power derating for IG BT (per device) 25 0 20 0 15 0 10 0 50 0 0 20 40 60 80 100 12 0 14 0 160 Case Tem p eratu re : Tc (°C) 0 0 .5 1 1.5 2 2.5 Co llector-Em itter vo lta g e : Vce (V) Transient therm al resistance Th erm al resista n ce : Rth (j-c) (°C /W ) Vc c= 15V 0 0 Co lle cter Power D issip ation : P c (W ) Collector current vs. Collector-Em itter voltage Tj=1 25°C 3