7MBP75RA060 600V / 75A 7 in one-package IGBT-IPM R series Features · Temperature protection provided by directly detecting the junction temperature of the IGBTs · Low power loss and soft switching · Compatible with existing IPM-N series packages · High performance and high reliability IGBT with overheating protection · Higher reliability because of a big decrease in number of parts in built-in control circuit Maximum ratings and characteristics Absolute maximum ratings(at Tc=25°C unless otherwise specified) Symbol Item DC bus voltage DC bus voltage (surge) DC bus voltage (short operating) Collector-Emitter voltage DB Reverse voltage INV Collector current DB Collector power dissipation Collector current DC 1ms DC One transistor DC 1ms Forward current of Diode Collector power dissipation One transistor Junction temperature Input voltage of power supply for Pre-Driver Input signal voltage Input signal current Alarm signal voltage Alarm signal current Storage temperature Operating case temperature Isolating voltage (Case-Terminal) Screw torque Mounting (M5) Terminal (M5) VDC VDC(surge) VSC VCES VR IC ICP -IC PC IC ICP IF PC Tj VCC *1 Vin *2 Iin VALM *3 IALM *4 Tstg Top Viso *5 Rating Min. Max. 0 0 200 0 0 0 0 0 -40 -20 - 450 500 400 600 600 75 150 75 320 50 100 50 198 150 20 Vz 1 Vcc 15 125 100 AC2.5 3.5 *6 3.5 *6 Unit V V V V V A A A W A A A W °C V V mA V mA °C °C kV N·m N·m Fig.1 Measurement of case temperature *1 Apply Vcc between terminal No. 3 and 1, 6 and 4, 9 and 7, 11 and 10. *2 Apply Vin between terminal No. 2 and 1, 5 and 4, 8 and 7, 12,13,14,15 and 10. *3 Apply VALM between terminal No. 16 and 10. *4 Apply IALM to terminal No. 16. *5 50Hz/60Hz sine wave 1 minute. Electrical characteristics of power circuit (at Tc=Tj=25°C, Vcc=15V) Item INV DB Symbol Collector current at off signal input Collector-Emitter saturation voltage Forward voltage of FWD Collector current at off signal input Collector-Emitter saturation voltage Forward voltage of Diode ICES VCE(sat) VF ICES VCE(sat) VF Condition VCE=600V input terminal open Ic=75A -Ic=75A VCE=600V input terminal open Ic=50A -Ic=50A Min. – – – – – – Typ. – – – – – – Max. 1.0 2.8 3.0 1.0 2.8 3.3 Unit mA V V mA V V 7MBP75RA060 IGBT-IPM Electrical characteristics of control circuit(at Tc=Tj=25°C, Vcc=15V) Item Power supply current of P-line side Pre-driver(one unit) Power supply current of N-line side three Pre-driver Input signal threshold voltage (on/off) Input zener voltage Over heating protection temperature level Hysteresis IGBT chips over heating protection temperature level Hysteresis Collector current protection level INV DB Over current protection delay time Under voltage protection level Hysteresis Alarm signal hold time SC protection delay time Limiting resistor for alarm Symbol Condition Min. Typ. Max. Iccp 3 18 fsw=0 to 15kHz Tc=-20 to 100°C * 7 ICCN 10 65 fsw=0 to 15kHz Tc=-20 to 100°C * 7 Vin(th) 1.00 1.35 1.70 ON 1.25 1.60 1.95 OFF VZ 8.0 Rin=20k ohm TCOH 125 VDC=0V, Ic=0A, Case temperature Fig.1 110 TCH 20 TjOH 150 surface of IGBT chips TjH 20 IOC 113 Tj=125°C Collector current IOC 75 Tj=125°C Collector current tDOC 10 Tj=25°C Fig.2 VUV 11.0 12.5 VH 0.2 tALM 1.5 2 tSC 12 Tj=25°C Fig.3 RALM 1425 1500 1575 Unit mA mA V V V °C °C °C °C A A µs V V ms µs ohm *7 Switching frequency of IPM Dynamic characteristics(at Tc=Tj=125°C, Vcc=15V) Item Switching time (IGBT) Symbol Condition ton toff trr Switching time (FWD) Min. IC=75A, VDC=300V Typ. Max. Unit - - µs µs µs 0.3 - IF=75A, VDC=300V 3.6 0.4 tsc Ioc Ic IALM Ic Ic Ic IALM IALM IALM Fig.3 Definition of tsc tDOC Fig.2 Definition of OC Delay Time Input Signal trr Irr 90% 90% Collector Current (Ic) 10% tf ton toff Fig.4 Definition of Switching Time Thermal characteristics(Tc=25°C) Item Junction to Case thermal resistance INV DB IGBT FWD IGBT Case to fin thermal resistance with compound Symbol Rth(j-c) Rth(j-c) Rth(j-c) Rth(c-f) Typ. 0.05 Max. 0.39 0.90 0.63 - Unit °C/W °C/W °C/W °C/W Typ. 15 - Max. 400 16.5 20 3.0 3.0 Unit V V kHz N·m N·m Recommendable value Item DC bus voltage Operating power supply voltage range of Pre-driver Switching frequency of IPM Screw torque Mounting (M5) Terminal (M5) Symbol VDC VCC fSW - Min. 200 13.5 1 2.5 2.5 7MBP75RA060 IGBT-IPM Block diagram Pre-drivers include following functions a) Short circuit protection circuit b) Amplifier for driver c) Undervoltage protection circuit d) Over current protection circuit e) IGBT chip over heating protection Outline drawings, mm 1 0 9 ±1 9 5 ±0.3 1 3 . 8 ±0.3 2 ±0.3 3 . 2 2 ±0.3 67.4 1 0 . 1 6 ±0.2 1 0 . 1 6±0.2 1 0 . 1 6±0.2 1 5 . 2 4 ±0.25 2 . 5 4 ±0.1 5 . 0 8±0.15 5 . 0 8±0.15 5 . 0 8±0.15 1 4 7 10 4-φ 5 . 5 （内径） 16 20 20 10 P N V U 0.5 17 W 0.5 24 26 26 16- 0 . 6 4 2-φ2 . 5 9 31 +1.0 2 2 -0.3 14.5 17 8 -0.2 +1.0 +1.0 7 6-M5 2 2 -0.3 8 8 ±1 7 4 ±0.3 B Mass : 440g 7MBP75RA060 Characteristics (Representative) Control Circuit IGBT-IPM 7MBP75RA060 Inverter IGBT-IPM 7MBP75RA060 IGBT-IPM 7MBP75RA060 IGBT-IPM 7MBP75RA060 Brake IGBT-IPM