SEME-LAB 2N2919_02

2N2919
MECHANICAL DATA
Dimensions in mm (inches)
8.51 (0.335)
9.40 (0.370)
DUAL NPN
PLANAR TRANSISTORS IN
TO77 PACKAGE
6.10 (0.240)
6.60 (0.260)
7.75 (0.305)
8.51 (0.335)
12.7 (0.500)
Min.
1.02
(0.040)
Max.
0.41 (0.016)
0.53 (0.021)
5.08
(0.200)
Applications
2.54
(0.100)
• Differential Amplifiers
4
2.54
(0.100)
3
5
• High Gain, Low Noise Audio Amplifiers
0.74 (0.029)
1.14 (0.045)
6
2
1
• Low Level Flip Flops
45˚
• Transducer Signal Conditioner Amplifiers
0.71 (0.028)
0.86 (0.034)
TO–77 PACKAGE (MO - 002AF)
Underside View
PIN 1 – Collector 1
PIN 2 – Base 1
PIN 3 – Emitter 1
PIN 4 – Emitter 2
PIN 5 – Base 2
PIN 6 – Collector 2
ABSOLUTE MAXIMUM RATINGS
(Tamb = 25°C unless otherwise stated)
VCBO
VCEO
VEBO
IC
PD
Collector – Base Voltage
Collector – Emitter Voltage
Emitter – Base Voltage
Continuous Collector Current
Total Device Dissipation
PD
Total Device Dissipation
TSTG
TL
Storage Temperature Range
Lead temperature (Soldering, 10 sec.)
TAMB = 25°C
Derate above 25°C
TC = 25°C
Derate above 25°C
EACH SIDE
TOTAL DEVICE
60V
60V
6V
30mA
300mW
500mW
1.72mW / °C
2.86W / °C
750mW
1.5W
4.3mW / °C
8.6mW / °C
–65 to 200°C
300°C
Semelab Plc reserves the right to change test conditions, parameter limits and package dimensions without notice. Information furnished by Semelab is believed
to be both accurate and reliable at the time of going to press. However Semelab assumes no responsibility for any errors or omissions discovered in its use.
Semelab encourages customers to verify that datasheets are current before placing orders.
Semelab plc.
Telephone +44(0)1455 556565. Fax +44(0)1455 552612.
E-mail: [email protected]
Website: http://www.semelab.co.uk
Document Number 3302
Issue 1
2N2919
ELECTRICAL CHARACTERISTICS (Tamb = 25°C unless otherwise stated)
Parameter
Test Conditions 1
Min.
Typ.
Max.
Unit
INDIVIDUAL TRANSISTOR CHARACTERISTICS
IC = 10µA
V(BR)CBO Collector – Base Breakdown Voltage
IE = 0
60
V(BR)CEO*
Collector – Emitter Breakdown Voltage IC = 10mA
IB = 0
60
V(BR)EBO
Emitter – Base Breakdown Voltage
IE = 10µA
IC = 0
6
ICBO
Collector Cut-off Current
VCB = 45V
IE = 0
2
nA
TA = 150°C
10
µA
ICEO
Collector Cut-off Current
VCE = 5V
IB = 0
2
IEBO
Emitter Cut-off Current
VEB = 5V
IC = 0
2
VCE = 5V
IC = 10µA
60
TA = –55°C
15
VCE = 5V
IC = 100µA
100
VCE = 5V
IC = 1mA
150
hFE
DC Current Gain
V
240
—
VBE
Base – Emitter Voltage
VCE = 5V
IC = 100µA
0.70
VCE(sat)
Collector – Emitter Saturation Voltage
IB = 100µA
IC = 1mA
0.35
hib
Small Signal Common – Base
VCB = 5V
Input Impedance
f = 1kHz
Small Signal Common – Base
VCB = 5V
Output Admittance
f = 1kHz
Small Signal Common – Base
VCE = 5V
Current Gain
f = 20MHz
Common – Base Open Circuit
VCB = 5V
Output Capacitance
f = 140kHz to 1MHz
hob
|hfe|
Cobo
IC = 1mA
25
IC = 1mA
IC = 500µA
nA
V
32
Ω
1
µmho
—
3
IE = 0
6
pF
* Pulse Test: tp = 300µs , δ ≤ 1%.
Parameter
Test Conditions
TRANSISTOR MATCHING CHARACTERISTICS
Static Forward Current Gain
VCE = 5V
hFE1
hFE2
Balance Ratio
IC = 100µA
See Note 2.
Min.
0.9
Typ.
Max.
Unit
1
—
VCE = 5V
IC = 100µA
3
VCE = 5V
IC = 10µA to 1mA
5
VCE = 5V
IC = 100µA
Base – Emitter Voltage Differential
TA1 = +25°C
TA2 = –55°C
Change With Temperature
VCE = 5V
IC = 100µA
TA1 = +25°C
TA2 = +125°C
|VBE1 – VBE2| Base – Emitter Voltage Differential
|∆(VBE1 – VBE2)∆TA|
mV
0.8
mV
1
NOTES
1) Terminals not under test are open circuited under all test conditions.
2) The lower of the two readings is taken as hFE1.
Semelab Plc reserves the right to change test conditions, parameter limits and package dimensions without notice. Information furnished by Semelab is believed
to be both accurate and reliable at the time of going to press. However Semelab assumes no responsibility for any errors or omissions discovered in its use.
Semelab encourages customers to verify that datasheets are current before placing orders.
Semelab plc.
Telephone +44(0)1455 556565. Fax +44(0)1455 552612.
E-mail: [email protected]
Website: http://www.semelab.co.uk
Document Number 3302
Issue 1