ICS ICS85310I-31

Integrated
Circuit
Systems, Inc.
ICS85310I-31
LOW SKEW, DUAL, 1-TO-5
2.5V/3.3V DIFFERENTIAL-TO-ECL/LVPECL FANOUT BUFFER
GENERAL DESCRIPTION
FEATURES
The ICS85310I-31 is a low skew, high performance
dual 1-to-5 Differential-to-2.5V/3.3V ECL/LVPECL
HiPerClockS™
Fanout Buffer and a member of the HiPerClockS™
family of High Performance Clock Solutions from
ICS. The CLKx, nCLKx pairs can accept most
standard differential input levels. The ICS85310I-31 is characterized to operate from either a 2.5V or a 3.3V power supply.
Guaranteed output and part-to-part skew characteristics make
the ICS85310I-31 ideal for those clock distribution applications
demanding well defined performance and repeatability.
• 2 differential 2.5V/3.3V LVPECL / ECL bank outputs
ICS
• 2 differential clock input pairs
• CLKx, nCLKx pairs can accept the following differential
input levels: LVPECL, LVDS, LVHSTL, SSTL, HCSL
• Maximum output frequency: 700MHz
• Translates any single ended input signal to 3.3V
LVPECL levels with resistor bias on nCLKx input
• Output skew: 25ps (typical)
• Part-to-part skew: 270ps (typical)
• Propagation delay: 1.7ns (typical)
• Additive phase jitter, RMS: <0.13ps (typical)
• LVPECL mode operating voltage supply range:
VCC = 2.375V to 3.8V, VEE = 0V
• ECL mode operating voltage supply range:
VCC = 0V, VEE = -3.8V to -2.375V
• -40°C to 85°C ambient operating temperature
• Lead-Free package fully RoHS compliant
BLOCK DIAGRAM
PIN ASSIGNMENT
QA0
nQA0
CLKA
nCLKA
VCC
1
24
QA3
CLK_ENA
2
23
nQA3
CLKA
3
22
QA4
nCLKA
4
21
nQA4
CLK_ENB
5
20
QB0
CLKB
6
19
nQB0
nCLKB
7
18
QB1
VEE
8
17
nQB1
QB1
nQB1
9 10 11 12 13 14 15 16
VCCO
QB2
nQB2
QB3
nQB3
32-Lead LQFP
7mm x 7mm x 1.4mm package body
Y Package
Top View
QB3
nQB3
QB4
nQB4
85310AYI-31
QB4
QB2
nQB2
nQB4
LE
ICS85310I-31
VCCO
Q
VCCO
QB0
nQB0
D
nQA2
QA4
nQA4
CLK_ENB
QA2
32 31 30 29 28 27 26 25
QA3
nQA3
CLKB
nCLKB
nQA1
LE
QA2
nQA2
QA1
Q
QA0
D
nQA0
CLK_ENA
VCCO
QA1
nQA1
www.icst.com/products/hiperclocks.html
1
REV. D JULY 6, 2005
ICS85310I-31
Integrated
Circuit
Systems, Inc.
LOW SKEW, DUAL, 1-TO-5
2.5V/3.3V DIFFERENTIAL-TO-ECL/LVPECL FANOUT BUFFER
TABLE 1. PIN DESCRIPTIONS
Number
Name
Type
1
VCC
Power
2
CLK_ENA
Unused
3
CLKA
Input
Description
Core supply pin.
Pullup
Synchronizing clock enable. LVCMOS/LVTTL interface levels.
Pulldown Non-inver ting differential clock input.
4
nCLKA
Input
Pullup
Inver ting differential clock input.
5
CLK_ENB
Unused
Pullup
Synchronizing clock enable. LVCMOS/LVTTL interface levels.
6
CLKB
Input
7
nCLKB
Input
8
VEE
Power
Negative supply pin.
9, 16, 25, 32
VCCO
Power
Output supply pins.
Pulldown Non-inver ting differential clock input.
Pullup
Inver ting differential clock input.
10, 11
nQB4, QB4
Output
Differential output pair. LVPECL interface levels.
12, 13
nQB3, QB3
Output
Differential output pair. LVPECL interface levels.
14, 15
nQB2, QB2
Output
Differential output pair. LVPECL interface levels.
17, 18
nQB1, QB1
Output
Differential output pair. LVPECL interface levels.
19, 20
nQB0, QB0
Output
Differential output pair. LVPECL interface levels.
21, 22
nQA4, QA4
Output
Differential output pair. LVPECL interface levels.
23, 24
nQA3, QA3
Output
Differential output pair. LVPECL interface levels.
26, 27
nQA2, QA2
Output
Differential output pair. LVPECL interface levels.
28, 29
nQA1, QA1
Output
Differential output pair. LVPECL interface levels.
30, 31
nQA0, QA0
Output
Differential output pair. LVPECL interface levels.
NOTE: Pullup and Pulldown refer to internal input resistors. See Table 2, Pin Characteristics, for typical values.
TABLE 2. PIN CHARACTERISTICS
Symbol
Parameter
CIN
Input Capacitance
4
pF
RPULLUP
Input Pullup Resistor
51
kΩ
RPULLDOWN
Input Pulldown Resistor
51
kΩ
85310AYI-31
Test Conditions
Minimum
www.icst.com/products/hiperclocks.html
2
Typical
Maximum
Units
REV. D JULY 6, 2005
ICS85310I-31
Integrated
Circuit
Systems, Inc.
LOW SKEW, DUAL, 1-TO-5
2.5V/3.3V DIFFERENTIAL-TO-ECL/LVPECL FANOUT BUFFER
TABLE 3A. CONTROL INPUT FUNCTION TABLE
Inputs
Outputs
CLK_ENA, CLK_ENB
QA0:QA4, QB0:QB4
nQA0:nQA4, nQB0:nQB4
0
Disabled; LOW
Disabled; HIGH
1
Enabled
Enabled
After CLK_EN switches, the clock outputs are disabled or enabled following a rising and falling input clock edge
as shown in Figure 1.
In the active mode, the state of the outputs are a function of the CLKA, nCLKA and CLKB, nCLKB inputs as described
in Table 3B.
Enabled
Disabled
CLKA, nCLKB
CLKA, CLKB
CLK_ENA,
CLK_ENB
nQA0:nQA4,
nQB0:nQB4
QA0:QA4,
QB0:QB4
FIGURE 1. CLK_EN TIMING DIAGRAM
TABLE 3B. CLOCK INPUT FUNCTION TABLE
Inputs
Outputs
nQA0:nQA4,
nQB0:nQB4
HIGH
Input to Output Mode
Polarity
Differential to Differential
Non Inver ting
Differential to Differential
Non Inver ting
CLKA or CLKB
nCLKA or nCLKB
0
1
QA0:QA4,
QB0:QB4
LOW
1
0
HIGH
LOW
0
Biased; NOTE 1
LOW
HIGH
Single Ended to Differential
Non Inver ting
1
Biased; NOTE 1
HIGH
LOW
Single Ended to Differential
Non Inver ting
Biased; NOTE 1
0
HIGH
LOW
Single Ended to Differential
Inver ting
Biased; NOTE 1
1
LOW
HIGH
Single Ended to Differential
Inver ting
NOTE 1: Please refer to the Application Information "Wiring The Differential Input To Accept Single Ended Levels".
85310AYI-31
www.icst.com/products/hiperclocks.html
3
REV. D JULY 6, 2005
ICS85310I-31
Integrated
Circuit
Systems, Inc.
LOW SKEW, DUAL, 1-TO-5
2.5V/3.3V DIFFERENTIAL-TO-ECL/LVPECL FANOUT BUFFER
ABSOLUTE MAXIMUM RATINGS
Supply Voltage, VCC
4.6V
Inputs, VI
-0.5V to VCC + 0.5V
Outputs, IO
Continuous Current
Surge Current
50mA
100mA
Package Thermal Impedance, θJA
47.9°C/W (0 lfpm)
Storage Temperature, TSTG
-65°C to 150°C
NOTE: Stresses beyond those listed under Absolute
Maximum Ratings may cause permanent damage to the
device. These ratings are stress specifications only. Functional
operation of product at these conditions or any conditions beyond those listed in the DC Characteristics or AC Characteristics is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect product reliability.
TABLE 4A. POWER SUPPLY DC CHARACTERISTICS, VCC, VCCO = 2.375V to 3.8V, TA = -40°C to 85°C
Symbol
Parameter
Test Conditions
Minimum
Typical
Maximum
Units
VCC
Core Supply Voltage
2.375
3.3
3.8
V
VCCO
Output Supply Voltage
2.375
3.3
3.8
V
IEE
Power Supply Current
120
mA
Maximum
Units
2
VCC + 0.3
V
-0.3
0.8
V
5
µA
TABLE 4B. LVCMOS / LVTTL DC CHARACTERISTICS, VCC, VCCO = 2.375V to 3.8V, TA = -40°C to 85°C
Symbol
Parameter
Test Conditions
VIH
Input High Voltage
CLK_ENA, CLK_ENB
VIL
Input Low Voltage
CLK_ENA, CLK_ENB
IIH
Input High Current
CLK_ENA, CLK_ENB
VCC = VIN = 3.8V
IIL
Input Low Current
CLK_ENA, CLK_ENB
VCC = 3.8V, VIN = 0V
Minimum
Typical
-150
µA
TABLE 4C. DIFFERENTIAL DC CHARACTERISTICS, VCC, VCCO = 2.375V to 3.8V, TA = -40°C to 85°C
Symbol
Parameter
Test Conditions
IIH
Input High Current
IIL
Input Low Current
VPP
Peak-to-Peak Input Voltage
Minimum
Typical
Maximum
Units
CLKA, CLKB
VCC = VIN = 3.8V
150
µA
nCLKA, nCLKB
VCC = VIN = 3.8V
5
µA
CLKA, CLKB
VCC = 3.8V, VIN = 0V
-5
nCLKA, nCLKB
VCC = 3.8V, VIN = 0V
-150
0.15
µA
µA
1.3
V
VCMR
Common Mode Input Voltage; NOTE 1, 2
VEE + 0.5
VCC - 0.85
V
NOTE 1: Common mode voltage is defined as VIH.
NOTE 2: For single ended applications, the maximum input voltage for CLKA, nCLKA and CLKB, nCLKB is VCC + 0.3V.
85310AYI-31
www.icst.com/products/hiperclocks.html
4
REV. D JULY 6, 2005
Integrated
Circuit
Systems, Inc.
ICS85310I-31
LOW SKEW, DUAL, 1-TO-5
2.5V/3.3V DIFFERENTIAL-TO-ECL/LVPECL FANOUT BUFFER
TABLE 4D. LVPECL DC CHARACTERISTICS, VCC, VCCO = 2.375V to 3.8V, TA = -40°C to 85°C
Symbol Parameter
Test Conditions
Minimum
Typical
Maximum
Units
Output High Voltage; NOTE 1
VCCO - 1.4
VCCO - 1.0
V
VOL
Output Low Voltage; NOTE 1
VCCO - 2.0
VCCO - 1.7
V
VSWING
Peak-to-Peak Output Voltage Swing
0.6
1.0
V
Maximum
Units
700
MHz
VOH
NOTE 1: Outputs terminated with 50Ω to VCCO - 2V.
TABLE 5. AC CHARACTERISTICS, VCC, VCCO = 2.375V to 3.8V, TA = -40°C to 85°C
Symbol
Parameter
fMAX
Output Frequency
tPD
Propagation Delay; NOTE 1
1.7
2. 2
ns
tsk(o)
Output Skew; NOTE 2, 4
25
50
ps
tsk(pp)
270
550
ps
tR
Par t-to-Par t Skew; NOTE 3, 4
Buffer Additive Phase Jitter, RMS;
refer to Additive Phase Jitter Section
Output Rise Time
20% to 80%
200
700
ps
tF
Output Fall Time
20% to 80%
200
700
ps
53
%
tjit
Test Conditions
Minimum
IJ 500MHz
Typical
<0.13
o dc
Output Duty Cycle
47
All parameters measured at 500MHz unless noted otherwise.
NOTE 1: Measured from the differential input crossing point to the differential output crossing point.
NOTE 2: Defined as skew between outputs at the same supply voltage and with equal load conditions.
Measured at the output differential cross points.
NOTE 3: Defined as skew between outputs on different devices operating at the same supply voltages
and with equal load conditions. Using the same type of inputs on each device, the outputs are measured
at the differential cross points.
NOTE 4: This parameter is defined in accordance with JEDEC Standard 65.
85310AYI-31
www.icst.com/products/hiperclocks.html
5
ps
REV. D JULY 6, 2005
Integrated
Circuit
Systems, Inc.
ICS85310I-31
LOW SKEW, DUAL, 1-TO-5
2.5V/3.3V DIFFERENTIAL-TO-ECL/LVPECL FANOUT BUFFER
ADDITIVE PHASE JITTER
the 1Hz band to the power in the fundamental. When the required offset is specified, the phase noise is called a dBc value,
which simply means dBm at a specified offset from the fundamental. By investigating jitter in the frequency domain, we get a
better understanding of its effects on the desired application over
the entire time record of the signal. It is mathematically possible
to calculate an expected bit error rate given a phase noise plot.
The spectral purity in a band at a specific offset from the fundamental compared to the power of the fundamental is called the
dBc Phase Noise. This value is normally expressed using a
Phase noise plot and is most often the specified plot in many
applications. Phase noise is defined as the ratio of the noise
power present in a 1Hz band at a specified offset from the fundamental frequency to the power value of the fundamental. This
ratio is expressed in decibels (dBm) or a ratio of the power in
0
-10
Additive Phase Jitter, RMS
-20
@ 155.52MHz = <0.13ps typical
-30
-40
-50
SSB PHASE NOISE dBc/HZ
-60
-70
-80
-90
-100
-110
-120
-130
-140
-150
-160
-170
-180
-190
100
1k
10k
100k
1M
10M
100M
OFFSET FROM CARRIER FREQUENCY (HZ)
vice meets the noise floor of what is shown, but can actually be
lower. The phase noise is dependant on the input source and
measurement equipment.
As with most timing specifications, phase noise measurements
have issues. The primary issue relates to the limitations of the
equipment. Often the noise floor of the equipment is higher than
the noise floor of the device. This is illustrated above. The de-
85310AYI-31
www.icst.com/products/hiperclocks.html
6
REV. D JULY 6, 2005
ICS85310I-31
Integrated
Circuit
Systems, Inc.
LOW SKEW, DUAL, 1-TO-5
2.5V/3.3V DIFFERENTIAL-TO-ECL/LVPECL FANOUT BUFFER
PARAMETER MEASUREMENT INFORMATION
2V
VCC,
VCCO
Qx
VCC
SCOPE
nCLKA, nCLKB
LVPECL
V
Cross Points
PP
V
CMR
CLKA, CLKB
nQx
VEE
V EE
-1.8V to -0.375V
3.3V OUTPUT LOAD AC TEST CIRCUIT
DIFFERENTIAL INPUT LEVEL
nQx
PART 1
Qx
nQx
nQy
nQy
Qx
PART 2
Qy
Qy
tsk(pp)
tsk(o)
PART-TO-PART SKEW
OUTPUT SKEW
nCLKA,
nCLKB
80%
80%
CLKA,
CLKB
VSW I N G
Clock
Outputs
20%
20%
nQAx,
nQBx
tF
tR
QAx,
QBx
OUTPUT RISE/FALL TIME
tPD
PROPAGATION DELAY
nQA0:nQA4,
nQB0:nQB4
QA0:QA4,
QB0:QB4
t PW
t
odc =
PERIOD
t PW
x 100%
t PERIOD
OUTPUT DUTY CYCLE/PULSE WIDTH/PERIOD
85310AYI-31
www.icst.com/products/hiperclocks.html
7
REV. D JULY 6, 2005
ICS85310I-31
Integrated
Circuit
Systems, Inc.
LOW SKEW, DUAL, 1-TO-5
2.5V/3.3V DIFFERENTIAL-TO-ECL/LVPECL FANOUT BUFFER
APPLICATION INFORMATION
WIRING THE DIFFERENTIAL INPUT TO ACCEPT SINGLE ENDED LEVELS
Figure 2 shows how the differential input can be wired to accept
single ended levels. The reference voltage V_REF = VCC/2 is
generated by the bias resistors R1, R2 and C1. This bias circuit
should be located as close as possible to the input pin. The ratio
of R1 and R2 might need to be adjusted to position the V_REF in
the center of the input voltage swing. For example, if the input
clock swing is only 2.5V and VCC = 3.3V, V_REF should be 1.25V
and R2/R1 = 0.609.
VCC
R1
1K
Single Ended Clock Input
CLKx
V_REF
nCLKx
C1
0.1u
R2
1K
FIGURE 2. SINGLE ENDED SIGNAL DRIVING DIFFERENTIAL INPUT
TERMINATION
FOR
3.3V LVPECL OUTPUTS
The clock layout topology shown below is a typical termination for LVPECL outputs. The two different layouts mentioned
are recommended only as guidelines.
50Ω transmission lines. Matched impedance techniques should
be used to maximize operating frequency and minimize signal
distortion. Figures 3A and 3B show two different layouts which
are recommended only as guidelines. Other suitable clock layouts may exist and it would be recommended that the board
designers simulate to guarantee compatibility across all printed
circuit and clock component process variations.
FOUT and nFOUT are low impedance follower outputs that generate ECL/LVPECL compatible outputs. Therefore, terminating
resistors (DC current path to ground) or current sources must
be used for functionality. These outputs are designed to drive
3.3V
Zo = 50Ω
125Ω
FOUT
125Ω
FIN
Zo = 50Ω
Zo = 50Ω
FOUT
50Ω
RTT =
1
Z
((VOH + VOL) / (VCC – 2)) – 2 o
Zo = 50Ω
VCC - 2V
RTT
84Ω
FIGURE 3A. LVPECL OUTPUT TERMINATION
85310AYI-31
FIN
50Ω
84Ω
FIGURE 3B. LVPECL OUTPUT TERMINATION
www.icst.com/products/hiperclocks.html
8
REV. D JULY 6, 2005
ICS85310I-31
Integrated
Circuit
Systems, Inc.
LOW SKEW, DUAL, 1-TO-5
2.5V/3.3V DIFFERENTIAL-TO-ECL/LVPECL FANOUT BUFFER
TERMINATION FOR 2.5V LVPECL OUTPUTS
Figure 4A and Figure 4B show examples of termination for 2.5V
LVPECL driver. These terminations are equivalent to terminating 50Ω to VCC - 2V. For VCC = 2.5V, the VCC - 2V is very close to
ground level. The R3 in Figure 4B can be eliminated and the
termination is shown in Figure 4C.
2.5V
2.5V
2.5V
VCCO=2.5V
VCCO=2.5V
R1
250
R3
250
Zo = 50 Ohm
Zo = 50 Ohm
+
+
Zo = 50 Ohm
Zo = 50 Ohm
-
-
2,5V LVPECL
Driv er
2,5V LVPECL
Driv er
R2
62.5
R1
50
R4
62.5
R2
50
R3
18
FIGURE 4A. 2.5V LVPECL DRIVER TERMINATION EXAMPLE
FIGURE 4B. 2.5V LVPECL DRIVER TERMINATION EXAMPLE
2.5V
VCCO=2.5V
Zo = 50 Ohm
+
Zo = 50 Ohm
2,5V LVPECL
Driv er
R1
50
R2
50
FIGURE 4C. 2.5V LVPECL TERMINATION EXAMPLE
85310AYI-31
www.icst.com/products/hiperclocks.html
9
REV. D JULY 6, 2005
ICS85310I-31
Integrated
Circuit
Systems, Inc.
LOW SKEW, DUAL, 1-TO-5
2.5V/3.3V DIFFERENTIAL-TO-ECL/LVPECL FANOUT BUFFER
DIFFERENTIAL CLOCK INPUT INTERFACE
The CLK /nCLK accepts LVDS, LVPECL, LVHSTL, SSTL, HCSL
and other differential signals. Both VSWING and VOH must meet the
VPP and VCMR input requirements. Figures 5A to 5E show interface examples for the HiPerClockS CLK/nCLK input driven by
the most common driver types. The input interfaces suggested
here are examples only. Please consult with the vendor of the
driver component to confirm the driver termination requirements.
For example in Figure 4A, the input termination applies for ICS
HiPerClockS LVHSTL drivers. If you are using an LVHSTL driver
from another vendor, use their termination recommendation.
3.3V
3.3V
3.3V
1.8V
Zo = 50 Ohm
CLK
Zo = 50 Ohm
CLK
Zo = 50 Ohm
nCLK
Zo = 50 Ohm
LVPECL
nCLK
HiPerClockS
Input
LVHSTL
ICS
HiPerClockS
LVHSTL Driver
R1
50
R1
50
HiPerClockS
Input
R2
50
R2
50
R3
50
FIGURE 5A. HIPERCLOCKS CLK/nCLK INPUT DRIVEN
ICS HIPERCLOCKS LVHSTL DRIVER
FIGURE 5B. HIPERCLOCKS CLK/nCLK INPUT DRIVEN
3.3V LVPECL DRIVER
BY
3.3V
3.3V
3.3V
3.3V
3.3V
R3
125
BY
R4
125
Zo = 50 Ohm
LVDS_Driv er
Zo = 50 Ohm
CLK
CLK
R1
100
Zo = 50 Ohm
nCLK
LVPECL
R1
84
HiPerClockS
Input
nCLK
Receiv er
Zo = 50 Ohm
R2
84
FIGURE 5C. HIPERCLOCKS CLK/nCLK INPUT DRIVEN
3.3V LVPECL DRIVER
FIGURE 5D. HIPERCLOCKS CLK/nCLK INPUT DRIVEN
3.3V LVDS DRIVER
BY
BY
3.3V
3.3V
3.3V
LVPECL
Zo = 50 Ohm
C1
Zo = 50 Ohm
C2
R3
125
R4
125
CLK
nCLK
R5
100 - 200
R6
100 - 200
R1
84
HiPerClockS
Input
R2
84
R5,R6 locate near the driver pin.
FIGURE 5E. HIPERCLOCKS CLK/nCLK INPUT DRIVEN
3.3V LVPECL DRIVER WITH AC COUPLE
85310AYI-31
BY
www.icst.com/products/hiperclocks.html
10
REV. D JULY 6, 2005
Integrated
Circuit
Systems, Inc.
ICS85310I-31
LOW SKEW, DUAL, 1-TO-5
2.5V/3.3V DIFFERENTIAL-TO-ECL/LVPECL FANOUT BUFFER
POWER CONSIDERATIONS
This section provides information on power dissipation and junction temperature for the ICS85310I-31.
Equations and example calculations are also provided.
1. Power Dissipation.
The total power dissipation for the ICS85310I-31 is the sum of the core power plus the power dissipated in the load(s).
The following is the power dissipation for VCC = 3.8V, which gives worst case results.
NOTE: Please refer to Section 3 for details on calculating power dissipated in the load.
•
•
Power (core)MAX = VCC_MAX * IEE_MAX = 3.8V * 120mA = 456mW
Power (outputs)MAX = 30.94mW/Loaded Output pair
If all outputs are loaded, the total power is 10 * 30.94mW = 309.4mW
Total Power_MAX (3.8V, with all outputs switching) = 456mW + 309.4mW = 765.4mW
2. Junction Temperature.
Junction temperature, Tj, is the temperature at the junction of the bond wire and bond pad and directly affects the reliability of the
device. The maximum recommended junction temperature for HiPerClockSTM devices is 125°C.
The equation for Tj is as follows: Tj = θJA * Pd_total + TA
Tj = Junction Temperature
θJA = Junction-to-Ambient Thermal Resistance
Pd_total = Total Device Power Dissipation (example calculation is in section 1 above)
TA = Ambient Temperature
In order to calculate junction temperature, the appropriate junction-to-ambient thermal resistance θJA must be used. Assuming a
moderate air flow of 200 linear feet per minute and a multi-layer board, the appropriate value is 42.1°C/W per Table 6 below.
Therefore, Tj for an ambient temperature of 85°C with all outputs switching is:
85°C + 0.765W * 42.1°C/W = 117.2°C. This is below the limit of 125°C.
This calculation is only an example. Tj will obviously vary depending on the number of loaded outputs, supply voltage, air flow,
and the type of board (single layer or multi-layer).
TABLE 6. THERMAL RESISTANCE θJA
FOR
32-PIN LQFP, FORCED CONVECTION
θJA by Velocity (Linear Feet per Minute)
0
Single-Layer PCB, JEDEC Standard Test Boards
Multi-Layer PCB, JEDEC Standard Test Boards
67.8°C/W
47.9°C/W
200
500
55.9°C/W
42.1°C/W
50.1°C/W
39.4°C/W
NOTE: Most modern PCB designs use multi-layered boards. The data in the second row pertains to most designs.
85310AYI-31
www.icst.com/products/hiperclocks.html
11
REV. D JULY 6, 2005
ICS85310I-31
Integrated
Circuit
Systems, Inc.
LOW SKEW, DUAL, 1-TO-5
2.5V/3.3V DIFFERENTIAL-TO-ECL/LVPECL FANOUT BUFFER
3. Calculations and Equations.
LVPECL output driver circuit and termination are shown in Figure 6.
VCCO
Q1
VOUT
RL
50
VCCO - 2V
Figure 6. LVPECL Driver Circuit and Termination
To calculate worst case power dissipation into the load, use the following equations which assume a 50Ω load, and a termination
voltage of V - 2V.
CCO
•
For logic high, VOUT = V
OH_MAX
(V
CC_MAX
•
-V
OH_MAX
=V
OL_MAX
-V
Pd_H = [(V
– (V
CCO_MAX
OH_MAX
CCO_MAX
– 0.935V
) = 0.935V
For logic low, VOUT = V
(V
=V
OL_MAX
CCO_MAX
– 1.67V
) = 1.67V
CCO_MAX
- 2V))/R ] * (V
CCO_MAX
L
-V
OH_MAX
) = [(2V - (V
CCO _MAX
-V
))/R ] * (V
OH_MAX
CCO _MAX
L
-V
)=
OH_MAX
[(2V - 0.935V)/50Ω] * 0.935V = 19.92mW
Pd_L = [(V
OL_MAX
– (V
CCO_MAX
- 2V))/R ] * (V
L
CCO_MAX
-V
OL_MAX
) = [(2V - (V
CCO_MAX
-V
OL_MAX
))/R ] * (V
L
CCO_MAX
-V
OL_MAX
)=
[(2V - 1.67V)/50Ω] * 1.67V = 11.02mW
Total Power Dissipation per output pair = Pd_H + Pd_L = 30.94mW
85310AYI-31
www.icst.com/products/hiperclocks.html
12
REV. D JULY 6, 2005
Integrated
Circuit
Systems, Inc.
ICS85310I-31
LOW SKEW, DUAL, 1-TO-5
2.5V/3.3V DIFFERENTIAL-TO-ECL/LVPECL FANOUT BUFFER
RELIABILITY INFORMATION
TABLE 7.
θJAVS. AIR FLOW TABLE FOR 32 LEAD LQFP
θJA by Velocity (Linear Feet per Minute)
Single-Layer PCB, JEDEC Standard Test Boards
Multi-Layer PCB, JEDEC Standard Test Boards
0
200
500
67.8°C/W
47.9°C/W
55.9°C/W
42.1°C/W
50.1°C/W
39.4°C/W
NOTE: Most modern PCB designs use multi-layered boards. The data in the second row pertains to most designs.
TRANSISTOR COUNT
The transistor count for ICS85310I-31 is: 1216
85310AYI-31
www.icst.com/products/hiperclocks.html
13
REV. D JULY 6, 2005
ICS85310I-31
Integrated
Circuit
Systems, Inc.
PACKAGE OUTLINE - Y SUFFIX
LOW SKEW, DUAL, 1-TO-5
2.5V/3.3V DIFFERENTIAL-TO-ECL/LVPECL FANOUT BUFFER
FOR
32 LEAD LQFP
TABLE 8. PACKAGE DIMENSIONS
JEDEC VARIATION
ALL DIMENSIONS IN MILLIMETERS
BBA
SYMBOL
MINIMUM
NOMINAL
MAXIMUM
32
N
A
--
--
1.60
A1
0.05
--
0.15
A2
1.35
1.40
1.45
b
0.30
0.37
0.45
c
0.09
--
0.20
D
9.00 BASIC
D1
7.00 BASIC
D2
5.60 Ref.
E
9.00 BASIC
E1
7.00 BASIC
E2
5.60 Ref.
0.80 BASIC
e
0.60
0.75
L
0.45
θ
0°
--
7°
ccc
--
--
0.10
Reference Document: JEDEC Publication 95, MS-026
85310AYI-31
www.icst.com/products/hiperclocks.html
14
REV. D JULY 6, 2005
Integrated
Circuit
Systems, Inc.
ICS85310I-31
LOW SKEW, DUAL, 1-TO-5
2.5V/3.3V DIFFERENTIAL-TO-ECL/LVPECL FANOUT BUFFER
TABLE 9. ORDERING INFORMATION
Part/Order Number
Marking
Package
Shipping Packaging
Temperature
ICS85310AYI-31
ICS85310AYI31
32 lead LQFP
tray
-40°C to 85°C
ICS85310AYI-31T
ICS85310AYI31
32 lead LQFP
1000 tape & reel
-40°C to 85°C
ICS85310AYI-31LF
ICS5310AI31L
32 lead "Lead Free" LQFP
tray
-40°C to 85°C
ICS85310AYI-31LFT
ICS5310AI31L
32 lead "Lead Free" LQFP
1000 tape & reel
-40°C to 85°C
NOTE: Par ts that are ordered with an "LF" suffix to the par t number are the Pb-Free configuration and are RoHS compliant.
The aforementioned trademark, HiPerClockS is a trademark of Integrated Circuit Systems, Inc. or its subsidiaries in the United States and/or other countries.
While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems, Incorporated (ICS) assumes no responsibility for either its use
or for infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use
in normal commercial and industrial applications. Any other applications such as those requiring high reliability, or other extraordinary environmental requirements are not
recommended without additional processing by ICS. ICS reserves the right to change any circuitry or specifications without notice. ICS does not authorize or warrant any ICS product
for use in life support devices or critical medical instruments.
85310AYI-31
www.icst.com/products/hiperclocks.html
15
REV. D JULY 6, 2005
Integrated
Circuit
Systems, Inc.
ICS85310I-31
LOW SKEW, DUAL, 1-TO-5
2.5V/3.3V DIFFERENTIAL-TO-ECL/LVPECL FANOUT BUFFER
REVISION HISTORY SHEET
Rev
Table
A
Page
9
A
A
B
T9
T4A
T2
T4D
C
D
T5
T9
85310AYI-31
14
4
Description of Change
Date
Added Termination for LVPECL Outputs.
Updated par t number from ICS85310-31 to ICS85310I-31 throughout the data
sheet to reflect operating temperature.
Corrected Marking from ICS85310AYI-31 to ICS85310AYI31.
Power Supply table - increased max. value for IEE to 120mA from 30mA max.
5/30/02
7/24/02
7/25/02
Power Considerations have re-adjusted to the increased IEE value.
Pin Characteristics Table - changed 4pF max. to 4pF typical.
Updated Absolute Maximum Ratings.
LVPECL DC Characteristics Table - changed VSWING from 0.85V max. to 1.0V max.
Application section added, Termination for 2.5V LVPECL Outputs and
Differential Clock Input Interface.
10 & 11 Power Considerations - recalculated Total Power Dissipation for 3.8V.
14
Ordering Information Table - corrected marking from ICS85310AYI31 to
ICS85310AI-31.
Features Section - added Additive Phase Jitter bullet and Lead-Free bullet.
1
AC Characteristics Table - added Additive Phase Jitter row.
5
Added Additive Phase Jitter Section.
6
Ordering Information Table - added Lead-Free Par t Number and Note.
14
10
2
4
5
8&9
www.icst.com/products/hiperclocks.html
16
10/23/02
7/31/03
7/6/05
REV. D JULY 6, 2005