TI INA223

INA223
www.ti.com
SBOS528 – JUNE 2012
Analog Output Current Shunt and Voltage
Instantaneous Power Monitor
Check for Samples: INA223
FEATURES
DESCRIPTION
•
•
•
The INA223 is a voltage-output device that monitors
the current, bus voltage, and power of a supply line
by sensing a voltage drop across a shunt at commonmode voltages from 0 V to 26 V. The common-mode
voltage range is independent of the supply voltage.
The low offset of the Zerø-Drift architecture enables
current sensing with maximum drops across the
shunt as low as 10 mV, full-scale.
1
23
•
•
•
•
Wide Common-Mode Range: 0 V to 26 V
±100 µV Offset (Max, Gain = 300 V/V)
Accuracy
– ±0.25% Shunt Voltage Gain Error (Max)
– ±0.15% Bus Voltage Gain Error (Max)
– 1.25% Power Error (Max)
– 0.3 μV/°C Offset Drift (Max)
– 50 ppm/°C Gain Drift (Max)
Programmable Gains
– Current Shunt Voltage Gains: 20, 128, 300
– Bus Voltage Attenuations: 1/10, 1/5, 2/5
Monitors/Measures/Reports:
– Instantaneous Power
– Bus Voltage
– Load Current
Quiescent Current: 250 µA (Max)
Shutdown Current: 1 µA (Max)
The INA223 includes a two-wire interface used for
adjusting the configuration settings of the device. The
interface is used to control the signal (current shunt
voltage, bus voltage, or power) that is directed to the
device output. Multiple gain and attenuation settings
can be programmed through the two-wire interface to
allow for application-specific configurations. The
programmable gain feature also allows the device to
be operated over a much wider dynamic current load
range without having to switch the sensing element
used.
APPLICATIONS
A shutdown feature is available to disable the device
and effectively disconnect it from the shunt resistor
and supply voltage, thus reducing the drain on the
battery.
•
•
•
•
The INA223 operates from a single +2.7-V to +5.5-V
supply, drawing a maximum supply current of 250 µA.
It is specified over the extended temperature range of
–40°C to +105°C, and is offered in an SON-10
package.
Notebook Computers
Cell Phones
Telecom Equipment
Power Management
Power Supply
(0V to 26V)
CBYPASS
0.1mF
RSHUNT
Load
VS (Supply Voltage)
Attenuator
RPULLUP
4.7kW
VIN-
VOUT
SCL
VIN+
Two-Wire
Interface
SDA
A0
INA223
GND
1
2
3
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
TransZorb is a trademark of General Instruments, Inc.
All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2012, Texas Instruments Incorporated
INA223
SBOS528 – JUNE 2012
www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
PACKAGE INFORMATION (1)
(1)
PRODUCT
PACKAGE-LEAD
PACKAGE
DESIGNATOR
PACKAGE
MARKING
INA223
SON-10
DSK
P223
For the most current package and ordering information, see the Package Option Addendum located at the end of this data sheet, or visit
the device product folder at www.ti.com.
ABSOLUTE MAXIMUM RATINGS (1)
Over operating free-air temperature range, unless otherwise noted.
Supply voltage
Analog inputs,
VIN+, VIN– (2)
Differential (VIN+) – (VIN–)
Common-mode (3)
Input current into any pin
(3)
INA223
UNIT
+6
V
–26 to +26
V
(GND – 0.3) to +26
V
5
mA
Operating temperature
–55 to +150
°C
Storage temperature
–65 to +150
°C
Junction temperature
Electrostatic
discharge
(ESD)ratings
(1)
(2)
(3)
2
+150
°C
Human body model (HBM)
2500
V
Charged-device model (CDM)
1000
V
Machine model (MM)
200
V
Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may
degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond
those specified is not implied.
VIN+ and VIN– are the voltages at the +IN and –IN pins, respectively.
Input voltage at any pin may exceed the voltage shown if the current at that pin is limited to 5 mA.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA223
INA223
www.ti.com
SBOS528 – JUNE 2012
ELECTRICAL CHARACTERISTICS
At TA = +25°C, VSENSE = (VIN+) – (VIN–) = 10 mV, VS = 3.3 V, and VIN+ = 12 V, unless otherwise noted.
INA223
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
INPUT
VCM
Common-mode input range
TA = –40°C to +105°C
TA = –40°C to +105°C, VIN+ = 0 V to +26 V,
VSENSE = 0 mV, Current shunt voltage gain = 20 V/V
CMR
Common-mode rejection
Shunt offset voltage, RTI (1)
VOS
dVOS/dT
vs temperature
PSR
vs power supply
Bus offset voltage, RTI (1)
VOS
dVOS/dT
vs temperature
PSR
vs power supply
IB
Input bias current
TA = –40°C to +105°C, VIN+ = 0 V to +26 V,
VSENSE = 0 mV, Current shunt voltage gain = 128 V/V,
300V/V
0
26
V
92
106
dB
100
120
dB
Current shunt voltage gain = 20 V/V
±75
±300
μV
Current shunt voltage gain = 128 V/V
±20
±150
μV
Current shunt voltage gain = 300 V/V
±15
±100
TA = –40°C to +105°C, current shunt voltage gain = 20 V/V
0.6
1
TA = –40°C to +105°C, current shunt voltage gain = 128 V/V,
300V/V
0.1
0.3
VS = +2.7 V to +5.5 V, current shunt voltage gain = 20 V/V
±15
±50
μV/V
VS = +2.7 V to +5.5 V, current shunt voltage gain = 128 V/V
±5
±25
μV/V
VS = +2.7 V to +5.5 V, current shunt voltage gain = 300 V/V
±2.5
±15
μV/V
Bus voltage gain = 0.1 V/V
±2.5
±20
mV
Bus voltage gain = 0.2 V/V
±2.5
±15
mV
Bus voltage gain = 0.4 V/V
±1.5
±10
mV
TA = –40°C to +105°C, bus voltage gain = 0.1 V/V
15
40
μV/°C
TA = –40°C to +105°C, bus voltage gain = 0.2 V/V, 0.4 V/V
10
30
μV/°C
VS = +2.7 V to +5.5 V
±9
±15
mV/V
18
25
μA
1
1.5
μA
Enabled, VIN+, VIN–
Disabled, VIN+, VIN–
Input impedance, differential
15
μV
μV/°C
2.5
kΩ
20, 128, 300
V/V
OUTPUT
GSV
Current shunt voltage gain
Current shunt voltage gain
error
TA = –40°C to +105°C, VSENSE = 10 mV to 155 mV, current
shunt voltage gain = 20 V/V
±0.05%
±0.25%
TA = –40°C to +105°C, VSENSE = 1.5 mV to 24 mV, current
shunt voltage gain = 128 V/V
±0.05%
±0.5%
±0.2%
±1%
TA = –40°C to +105°C, VSENSE = 1 mV to 9 mV, current shunt
voltage gain = 300 V/V
vs temperature
Nonlinearity error
GBV
TA = –40°C to +105°C, current shunt voltage gain = 20 V/V
50
ppm/°C
TA = –40°C to +105°C, current shunt voltage gain = 128 V/V
75
ppm/°C
TA = –40°C to +105°C, current shunt voltage gain = 300 V/V
125
ppm/°C
VSENSE = 1 mV to 10 mV
Bus voltage gain
Bus voltage gain error
vs temperature
V/V
TA = –40°C to +105°C, bus voltage gain = 0.1 V/V,
VCM = 0.5V to 26V
±0.05%
±0.2%
TA = –40°C to +105°C, bus voltage gain = 0.2 V/V,
VCM = 0.5 V to 12 V
±0.025%
±0.15%
TA = –40°C to +105°C, bus voltage gain = 0.4V/V,
VCM = 0.5 V to 6 V
±0.025%
±0.15%
TA = –40°C to +105°C
Nonlinearity error
(1)
±0.01%
0.1, 0.2, 0.4
5
ppm/°C
±0.01%
RTI = referred-to-input.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA223
3
INA223
SBOS528 – JUNE 2012
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
At TA = +25°C, VSENSE = (VIN+) – (VIN–) = 10 mV, VS = 3.3 V, and VIN+ = 12 V, unless otherwise noted.
INA223
PARAMETER
TEST CONDITIONS
MIN
Current shunt voltage gain = 20 V/V; bus voltage gain = 0.1
V/V, 0.2V/V, 0.4V/V
Power measurement error
TYP
MAX
UNIT
±0.35
±1.25
%FSR
±2
%FSR
±1.5
%FSR
±2.25
%FSR
Current shunt voltage gain = 20 V/V; bus voltage gain = 0.1
V/V, 0.2V/V, 0.4V/V TA = –40°C to +105°C
Current shunt voltage gain = 128 V/V, 300V/V; bus voltage
gain = 0.1 V/V, 0.2V/V, 0.4V/V
±0.35
Current shunt voltage gain = 128 V/V, 300V/V; bus voltage
gain = 0.1 V/V, 0.2V/V, 0.4V/V; TA = –40°C to +105°C
Output impedance
Maximum capacitive load
No sustained oscillation
4
Ω
1
nF
VOLTAGE OUTPUT (2)
Swing to VS power-supply rail
TA = –40°C to +105°C, RL = 10 kΩ to GND
VS – 0.015
VS – 0.035
V
Swing to GND
TA = –40°C to +105°C, RL = 10 kΩ to GND
VGND + 2.5
VGND + 10
mV
FREQUENCY RESPONSE
GBW
SR
Bandwidth
Gain = 300, CLOAD = 10 pF
10
kHz
Gain = 128, CLOAD = 10 pF
20
kHz
Gain = 20, CLOAD = 10 pF
25
kHz
0.25
V/μs
0.1 Hz to 10 Hz, current shunt voltage gain = 20 V/V
235
nV/√Hz
0.1 Hz to 10 Hz, current shunt voltage gain = 300 V/V
54
nV/√Hz
Slew rate
NOISE, RTI (1)
Voltage noise density
DIGITAL INPUTS (SDA as Input, SCL, A0)
Input capacitance
3
pF
VIH
High-level input voltage
0.7(VS)
6
VIL
Low-level input voltage
–0.3
0.3(VS)
V
1
μA
(2)
4
Leakage input current
0.1
Hysteresis
500
V
mV
See Typical Characteristic curve, Output Swing vs Output Current (Figure 22).
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA223
INA223
www.ti.com
SBOS528 – JUNE 2012
ELECTRICAL CHARACTERISTICS (continued)
At TA = +25°C, VSENSE = (VIN+) – (VIN–) = 10 mV, VS = 3.3 V, and VIN+ = 12 V, unless otherwise noted.
INA223
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
POWER SUPPLY
VS
Operating range
IQ
Quiescent current
TA = –40°C to +105°C
+5.5
V
Enabled
+2.7
200
250
μA
Disabled
0.1
1
μA
Power-on reset threshold
2
V
TEMPERATURE
Specified range
–40
+105
°C
THERMAL INFORMATION
INA223
THERMAL METRIC (1)
DSK (SON)
UNITS
10 PINS
θJA
Junction-to-ambient thermal resistance
47.5
θJCtop
Junction-to-case (top) thermal resistance
57.9
θJB
Junction-to-board thermal resistance
21.5
ψJT
Junction-to-top characterization parameter
0.8
ψJB
Junction-to-board characterization parameter
21.8
θJCbot
Junction-to-case (bottom) thermal resistance
4.6
(1)
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA223
5
INA223
SBOS528 – JUNE 2012
www.ti.com
PIN CONFIGURATIONS
DSK PACKAGE
SON-10
(TOP VIEW)
1
10
VIN+
(1)
VIN-
2
9
VIN+
GND
3
8
A0
VS
4
7
SDA
6
SCL
VOUT
5
INA223
VIN-
Thermal Pad
(2)
(1)
(1)
See Application Information section for a description of how to connect input pins to the shunt resistor.
(2)
Must be connected to ground.
PIN DESCRIPTIONS
PIN
NAME
NUMBER
ANALOG/DIGITAL
INPUT/OUTPUT
A0
8
Digital input
GND
3
Analog
DESCRIPTION
Address pin. Connect to GND, SCL, SDA, or VS. Table 6 shows pin settings and corresponding
address.
Ground
SCL
6
Digital input
Serial bus clock line
SDA
7
Digital I/O
Serial bus data line
VIN+
9
Analog input
Connect to supply side of shunt resistor. This pin can also be connected directly to pin 10.
VIN+
10
Analog input
Connect to supply side of shunt resistor
VIN–
1
Analog input
Connect to load side of shunt resistor
VIN–
2
Analog input
Connect to load side of shunt resistor. This pin can also be connected directly to pin 1.
VOUT
5
Analog output
VS
4
Analog
6
Output signal selected by multiplexer
Power supply (2.7 V to 5.5 V)
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA223
INA223
www.ti.com
SBOS528 – JUNE 2012
TYPICAL CHARACTERISTICS
At TA = +25°C, VS = +3.3 V, VIN+ = 12 V unless otherwise noted.
SHUNT OFFSET VOLTAGE (G = 128 V/V)
PRODUCTION DISTRIBUTION
75
50
25
0
−25
−50
−75
−100
300
250
200
150
100
50
0
−50
−100
−150
−200
−250
Population
Population
SHUNT OFFSET VOLTAGE (G = 20 V/V)
PRODUCTION DISTRIBUTION
Input Offset Voltage (µV)
Input Offset Voltage (µV)
G002
G001
Figure 1.
Figure 2.
SHUNT OFFSET VOLTAGE (G = 300 V/V)
PRODUCTION DISTRIBUTION
SHUNT OFFSET VOLTAGE
vs TEMPERATURE
50
Gain = 300 V/V
Population
Offset Voltage (µV)
0
−50
Gain = 128 V/V
−100
Gain = 20 V/V
Input Offset Voltage (µV)
60
50
40
30
20
10
0
−10
−20
−30
−40
−50
−150
−200
−50
−25
0
25
50
Temperature (°C)
75
100
125
G004
G003
Figure 4.
SHUNT INPUT CMRR (G = 20 V/V)
PRODUCTION DISTRIBUTION
SHUNT INPUT CMRR (G = 128 V/V and 300 V/V)
PRODUCTION DISTRIBUTION
Common−Mode Rejection Ratio (µV/V)
Common−Mode Rejection Ratio (µV/V)
G005
Figure 5.
6
5
4
3
2
1
0
−1
−2
−3
−4
−5
20
15
10
5
0
−5
−10
−15
−20
Population
Population
Figure 3.
G006
Figure 6.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA223
7
INA223
SBOS528 – JUNE 2012
www.ti.com
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, VS = +3.3 V, VIN+ = 12 V unless otherwise noted.
SHUNT INPUT CMRR
vs TEMPERATURE
SHUNT GAIN ERROR (G = 20 V/V and 128 V/V)
PRODUCTION DISTRIBUTION
1
Gain = 20V/V
Population
CMRR (µV/V)
0.5
0
Gain = 128, 300 V/V
Gain Error (%)
0.2
0.15
G007
0.1
125
0.05
100
0
75
−0.05
25
50
Temperature (°C)
−0.1
0
−0.15
−25
−0.2
−1
−50
−0.25
−0.5
G008
Figure 7.
Figure 8.
SHUNT GAIN ERROR (G = 300 V/V)
PRODUCTION DISTRIBUTION
SHUNT GAIN ERROR
vs TEMPERATURE
0.5
Population
Gain Error (%)
0.2
Gain = 20 V/V
Gain = 300 V/V
−0.5
−50
0.5
0.4
0.3
0.2
0.1
0
−0.1
−0.2
−0.3
−0.4
−0.5
−0.6
−0.2
Gain Error (%)
−25
0
25
50
Temperature (°C)
75
100
125
G010
G009
Figure 10.
BUS OFFSET VOLTAGE (G = 0.1 V/V and 0.2 V/V)
PRODUCTION DISTRIBUTION
BUS OFFSET VOLTAGE (G = 0.4 V/V)
PRODUCTION DISTRIBUTION
Input Offset Voltage (mV)
G011
Figure 11.
6
5
4
3
2
1
0
−1
−2
−3
−4
−5
12.5
10
7.5
5
2.5
0
−2.5
−5
−7.5
Population
Population
Figure 9.
Input Offset Voltage (mV)
8
Gain = 128 V/V
0
G012
Figure 12.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA223
INA223
www.ti.com
SBOS528 – JUNE 2012
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, VS = +3.3 V, VIN+ = 12 V unless otherwise noted.
BUS OFFSET VOLTAGE
vs TEMPERATURE
BUS GAIN ERROR (G = 0.1 V/V)
PRODUCTION DISTRIBUTION
2.5
Population
Gain = 0.2, 0.4 V/V
0
Gain = 0.1 V/V
G013
Gain Error (%)
Figure 13.
Figure 14.
BUS GAIN ERROR (G = 0.2 V/V and 0.4 V/V)
PRODUCTION DISTRIBUTION
BUS GAIN ERROR
vs TEMPERATURE
0.15
0.125
125
0.1
100
0.075
75
0.05
25
50
Temperature (°C)
0.025
0
0
−25
−0.025
−5
−50
−0.05
−2.5
−0.075
Offset Voltage (mV)
5
G014
0.2
Population
Gain Error (%)
0.1
Gain = 0.1 V/V
Gain = 0.2 V/V
0
Gain = 0.4 V/V
Gain Error (%)
−0.2
−50
0.1
0.075
0.05
0.025
0
−0.025
−0.05
−0.075
−0.1
−25
0
25
50
Temperature (°C)
75
100
125
G016
G015
Figure 15.
Figure 16.
POWER GAIN ERROR
PRODUCTION DISTRIBUTION
POWER GAIN
vs TEMPERATURE
1.5
1.2
Population
Gain Error (%)
1
0.8
0.5
0.2
0
Power Error (%)
1.5
1.25
1
0.75
0.5
0.25
0
−0.25
−0.5
−0.2
−0.5
−50
−25
0
25
50
Temperature (°C)
75
100
125
G018
G017
Figure 17.
Figure 18.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA223
9
INA223
SBOS528 – JUNE 2012
www.ti.com
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, VS = +3.3 V, VIN+ = 12 V unless otherwise noted.
SHUNT INPUT CMR
vs FREQUENCY
GAIN
vs FREQUENCY
120
60
Gain=300V/V
100
Gain=128V/V
Gain (dB)
CMR (dB)
40
80
Gain=20V/V
20
60
VCM = 1V + 100mVpp
VDIFF = 5mV
40
1
10
100
Frequency (Hz)
VCM = 1V
VDIFF = 100mVpp Sine
1k
0
10k 20k
10
100
G019
1k
Frequency (Hz)
Figure 20.
PSRR
vs FREQUENCY
OUTPUT VOLTAGE SWING
vs OUTPUT CURRENT
VS
VS = 3 V to 5.5 V
Output Voltage Swing (V)
VS − 0.5
PSRR (dB)
100
80
60
VS = 3.3 V + 100 mVpp
VCM = 1 V
VDIFF = 5 mV
10
100
VS − 1
VS − 1.5
VS − 2
VS − 2.5
VS = 2.7 V to 5.5 V
GND + 2.5
VS = 2.7 V
GND + 2
GND + 1.5
TA = −40°C
TA = +25°C
TA = +105°C
GND + 1
GND + 0.5
1k
Frequency (Hz)
100k
G020
Figure 19.
120
40
10k
GND
10k 20k
0
5
G021
10
15
20
25
Current (mA)
30
35
G022
Figure 21.
Figure 22.
INPUT BIAS CURRENT
vs COMMON-MODE VOLTAGE, ENABLED
INPUT BIAS CURRENT
vs COMMON-MODE VOLTAGE, DISABLED
25
40
0.2
Input Bias Current (µA)
Input Bias Current (µA)
20
15
10
5
0.15
0.1
0.05
0
−5
0
5
10
15
20
Common−Mode Voltage (V)
25
30
0
0
G023
Figure 23.
10
5
10
15
20
Common−Mode Voltage (V)
25
30
G024
Figure 24.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA223
INA223
www.ti.com
SBOS528 – JUNE 2012
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, VS = +3.3 V, VIN+ = 12 V unless otherwise noted.
250
39
240
Quiescent Current (µA)
40
38
37
IB = (IB+) + (IB−)
36
35
−50
Input−Referred Voltage Noise (nV/ÖHz)
QUIESCENT CURRENT
vs TEMPERATURE
−25
0
25
50
Temperature (°C)
75
100
220
210
200
−50
125
−25
G025
0
25
50
Temperature (°C)
Figure 25.
Figure 26.
INPUT REFERRED VOLTAGE NOISE
vs FREQUENCY
0.1-Hz TO 10-Hz
VOLTAGE NOISE
400
G = 20 V/V
100
G = 300 V/V
10
230
10
100
1k
Frequency (Hz)
10k 20k
Referred-to-Input Voltage Noise (200 nV/div)
Input Bias Current (µA)
INPUT BIAS CURRENT
vs TEMPERATURE
75
100
125
G026
G = 20 V/V
G = 300 V/V
Time (1 s/div)
G027
Figure 27.
Figure 28.
SHUNT INPUT STEP RESPONSE
GAIN = 20 V/V
SHUNT INPUT STEP RESPONSE
GAIN = 128 V/V
G028
25
0.25
Input (mV)
Input (V)
20
0.15
0.05
15
10
5
0
VS = 5 V
Output (V)
Output (V)
4
3
2
1
0
Time (50 ms/div)
2.5
2
1.5
1
0.5
0
G029
Figure 29.
Time (50 ms/div)
G030
Figure 30.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA223
11
INA223
SBOS528 – JUNE 2012
www.ti.com
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, VS = +3.3 V, VIN+ = 12 V unless otherwise noted.
0.25
Input (V)
3.5
3
2.5
2
1.5
1
0.5
0
INPUT OVERLOAD
RECOVERY
0.15
0.05
4
Output (V)
Input (mV)
14
12
10
8
6
4
2
Output (V)
SHUNT INPUT STEP RESPONSE
GAIN = 300 V/V
3
2
1
0
Time (50 ms/div)
G031
Figure 31.
12
Time (50 ms/div)
G032
Figure 32.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA223
INA223
www.ti.com
SBOS528 – JUNE 2012
APPLICATION INFORMATION
The INA223 is an analog output current shunt monitor that incorporates an analog multiplier to provide
instantaneous power measurement. The INA223 features a two-wire and SMBus-compatible interface allowing
the configuration settings of the device to be adjusted and changed as needed, based on the specific application
requirements. The configuration options include the selection of the desired signal to be available at the output
pin, switching between multiple current shunt voltage gains and bus voltage attenuation factors, as well as being
able to place the device into a disabled state.
INA223 TYPICAL APPLICATION
Figure 33 shows the typical application circuit for the INA223. The input pins, VIN+ and VIN–, should be connected
as close as possible to the shunt resistor to minimize any resistance in series with the shunt resistance. A powersupply bypass capacitor is required for stability. Use a 0.1-μF ceramic capacitor for supply bypassing, placed as
close as possible between the supply and ground pins.
Power Supply
(0V to 26V)
CBYPASS
0.1mF
RSHUNT
Load
VS (Supply Voltage)
Attenuator
RPULLUP
4.7kW
VIN-
VOUT
SCL
VIN+
Two-Wire
Interface
SDA
A0
INA223
GND
Figure 33. Typical Application
BASIC FUNCTIONS
The INA223 can be configured to monitor and report the differential voltage developed across a shunt resistor,
the power supply bus voltage, or the power being delivered to the load. Through the two-wire interface, the
output multiplexer (mux) can be configured to provide a proportional output signal to any one of these input
signals at the output pin, VOUT. The digital interface can also be used to switch between different current shunt
voltage gains, bus voltage attenuation settings, as well as place the device into a disabled mode. The multiple
settings available for the current shunt voltage gains and bus voltage attenuation factors allow the INA223 to
operate over a wider input signal range than a single fixed-setting device would allow.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA223
13
INA223
SBOS528 – JUNE 2012
www.ti.com
Shunt Voltage
The INA223 has three available current shunt voltage gain options that can be selected using the two-wire
interface. This allows for optimization of the output signal to maximize the available dynamic range. This flexibility
provides a benefit over a fixed-gain current shunt monitor. A fixed-gain current shunt monitor has a finite range of
current that can be monitored based on the limitations of the output stage of the device.
For example, in a typical application using a fixed-gain current shunt monitor, the shunt resistor is selected to
achieve the maximum allowable full-scale output based on the maximum expected current to be monitored and
the fixed gain value of the current shunt monitor. One limitation to a fixed gain approach is in the minimum
current level that can be monitored. The minimum current than can be monitored is based on the ability of the
output stage of the current shunt monitor to swing to ground. This minimum current level is calculated based on
the maximum swing to ground specification (50 mV for the INA223), which is then divided by the fixed gain of the
device. This calculation provides the minimum differential voltage that can be monitored and then divided by the
shunt resistor to determine the minimum current that can be monitored. After the monitored current drops below
this level, further decreases in the monitored current can no longer be detected at the output. The ability to
switch the current shunt voltage gain to a higher gain setting brings the output level above this saturation point
and enables lower currents to be monitored, thus extending the dynamic range of the device.
Bus Voltage Range
The INA223 monitors bus voltages that can range from 0 V to 26 V. This voltage must be internally divided down
to interface with the analog multiplier and output stage circuitry. The supply voltage for the INA223 can range
from 2.7 V to 5.5 V; therefore, the bus voltage must be divided down so that it does not exceed the supply
voltage. If this divider ratio or attenuation factor results in an internal voltage that exceeds the supply voltage, the
measurement circuitry is saturated. The device will not be damaged, but the measurement result at the output
will be invalid. Having multiple attenuation factors (0.1 V/V, 0.2 V/V, 0.4 V/V) allows for the optimization of the
output range based on the specific common-mode voltage present. Having multiple values that can be selected
provides a helpful advantage over a single fixed-attenuation device, given the wide common-mode range of the
INA223. With a single attenuation factor, the maximum common-mode voltage (26 V) must be divided down to
less than the minimum supply voltage (2.7 V). A bus voltage less than 26 V results in a significantly smaller
output range. The ability to switch between different attenuation settings allows the device to be configured to
maximize the dynamic output range at multiple common-mode voltage levels. Additionally, because the power
calculation is based on the bus voltage measurement, the larger the corresponding representation of the
common-mode voltage, the more accurate the power calculation.
Output Range
The power calculation has two inputs: the current shunt voltage measurement, as well as the bus voltage
measurement. Both of these measurements must be valid (within the linear range of the device) to achieve a
valid power calculation. Set the gain setting for the current shunt voltage and attenuation setting for the bus
voltage to allow each of these two measurements to remain within the linear range of the device, based on the
input conditions. Saturating one of these two measurements may not result in the output being saturated based
on the internal scaling of the analog multiplier; therefore, care should be taken to ensure that the two inputs to
the multiplier are valid.
Shutting Down the INA223
The INA223 includes a shutdown feature that is programmed through the serial interface. Setting the Enable bit
in the Configuration Register to '0' places the INA223 into a disabled state. While in the disabled state, the input
bias currents and device quiescent current drop below 1 μA, thus reducing the power consumption of the system
when this device is not in use. The device is placed back into the active mode by setting the Enable bit high. The
time required for the INA223 output to be valid after enabling the device to come out of the shutdown state is
typically 40 µs.
In addition to responding to the Enable bit, the INA223 also responds to an Enable and Disable General Call as
described in the GENERAL CALL section.
14
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA223
INA223
www.ti.com
SBOS528 – JUNE 2012
CONFIGURATION REGISTER
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
BIT
NAME
BIT
—
—
—
—
—
—
—
—
—
EN
OUT1
OUT0
GSV1
GSV0
GBV1
GBV0
POR
VALUE
0
0
0
0
0
0
0
0
0
1
1
0
0
0
0
1
EN
Enable/Disable Mode
Bit 6
Setting this bit to '0' places the device into a disabled mode.
This mode drops the input bias current to 1 μA for each of the analog inputs and reduces the
quiescent current to 1 μA.
OUT
Output Mode
Bits 4, 5
Controls the setting of the output mux to select the signal that is available at the output pin.
There are two different mode settings for selecting power at the output pin. The Supply Power
output mode sets the bus voltage measurement to be taken at the VIN+ pin to calculate the
power provided by the power supply. The Load Power output mode sets the bus voltage
measurement to be taken at the VIN– pin to calculate the power consumed by the load. Refer
to Table 1.
Table 1. Output Mode Settings (1)
(1)
OUT1
OUT0
D5
D4
0
0
Bus Voltage Measurement
0
1
Shunt Voltage Measurement
1
0
Supply Power
1
1
Load Power
OUTPUT MODE
Shaded cells indicate default value.
GSV
Current Shunt Voltage Gain
Bits 2, 3
Sets the gain for the current shunt voltage measurement. Table 2 summarizes the gain
settings.
Table 2. Current Shunt Voltage Gain Settings (1)
(1)
GSV1
GSV0
D3
D2
CURRENT SHUNT VOLTAGE
GAIN
0
0
20 V/V
0
1
128 V/V
1
0
300 V/V
Shaded cells indicate default value.
GBV
Bus Voltage Gain
Bits 0, 1
Sets the gain for the bus voltage measurement. Refer to Table 3.
Table 3. Bus Voltage Gain Settings (1)
(1)
GBV1
GBV0
D1
D0
BUS VOLTAGE GAIN
0
0
2/5 V/V
0
1
1/5 V/V
1
0
1/10 V/V
Shaded cells indicate default value.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA223
15
INA223
SBOS528 – JUNE 2012
www.ti.com
OUTPUT
The signal available at the output pin is selected by the output mode setting programmed in the Configuration
Register. The default setting for the output mux is the Supply Power mode. For the power value to be valid, both
the shunt voltage measurement and the bus voltage measurement must both be valid (within the linear range of
the device).
Power Calculation
The output voltage for the two power output modes is calculated as shown in Equation 1. To convert the output
voltage to the corresponding power representation, the output voltage must be divided by the product of the
power gain shown in Table 4 and the value of the shunt resistor.
VOUT = (VCM)(VSENSE)(POWERGAIN)
(1)
POWER =
VOUT
(POWERGAIN)(RSHUNT)
(2)
Table 4. PowerGAIN Values
GBV
GSV
POWERGAIN
0.1 V/V
20 V/V
0.667
0.1 V/V
128 V/V
4.267
0.1 V/V
300 V/V
10
0.2 V/V
20 V/V
1.333
0.2 V/V
128 V/V
8.533
0.2 V/V
300 V/V
20
0.4 V/V
20 V/V
2.667
0.4 V/V
128 V/V
17.067
0.4 V/V
300 V/V
40
Power Calculation Example
The following example is based on Figure 34. In this example the system consists of a load current of 5 A and a
common-mode voltage of 12 V. This 5-A current flowing through the 1-mΩ shunt resistor develops a differential
voltage of 5 mV across the INA223 input pins. With the 3.3-V supply voltage shown here, a practical full-scale
target for the output voltage is 3 V.
+12V
VCM
CBYPASS
0.1mF
RSHUNT
1mW
+3.3V
Supply
5A Load
Attenuator
RPULLUP
4.7kW
VIN-
VOUT
SCL
VIN+
Two-Wire
Interface
SDA
A0
INA223
GND
Figure 34. Example Circuit
16
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA223
INA223
www.ti.com
SBOS528 – JUNE 2012
Current Shunt Voltage Measurement Mode
Based on the 5-mV differential voltage present at the input and the device set to Current Shunt Voltage mode, a
current shunt voltage gain setting of 300 V/V is selected resulting in an output voltage of 1.5 V. A current shunt
voltage gain setting less than 300 V/V could also be used in this example. The drawback of a lower gain setting
is a smaller dynamic range present at the output as well as a less accurate input for the power measurement in
the Power Output mode. A larger shunt resistor (2 mΩ) could also be used to increase the full-scale drop to
result. One drawback of increasing the impedance of the shunt resistor is the increased power dissipation
requirement the component must be able to accommodate. A higher-accuracy power measurement is obtained
with the largest possible input from the current shunt voltage, while remaining within the linear range of the
device.
Bus Voltage Measurement Mode
Assuming the same 3-V target as previously discussed, and with the device set to Bus Voltage mode, an
attenuation factor of 0.2 V/V results in an output voltage of 2.4 V. An attenuation factor of 0.1 V/V could also be
used, but results in a lower dynamic output range. An attenuation factor of 0.4 V/V cannot be used in this
example because it results in an internal voltage of 4.8 V, exceeding the supply voltage of 3.3 V.
Power Modes
For the power output modes, the current shunt voltage and bus voltage measurements are multiplied by the
Power Gain factor to yield a voltage output representing the calculated power. In this example, the 5 mV
developed across the shunt resistor is multiplied by the 12-V bus voltage. This product is then multiplied by the
Power Gain factor of 20 (GSV = 300 V/V, GBV = 0.2 V/V; See Table 4), and results in a 1.2-V output voltage
representation of the power. Using Equation 2 and the corresponding Power Gain of 20, the power being
consumed by the load is calculated to be 60 W. This corresponds to the original 5-A load current and 12-V
common-mode voltage conditions.
Bus Voltage Measurement Location for Power Output Modes
For the power output mode, the bus voltage can be measured either at the VIN+ (supply side) or at the VIN– (load
side) pins when the current shunt voltage gain setting is 20. When the current shunt voltage gain setting is 128
or 300, this measurement assumes a relatively small differential voltage is being developed across the sense
resistor. With a small drop across the sense resistor, the voltages at VIN+ and VIN– are very close to one another,
making the shunt voltage impact on the bus voltage measurement much less critical. When the device set to a
gain of 20, it implies that a greater differential voltage is being developed across the sense resistor, causing the
voltages at the VIN+ and VIN– pins to be noticeably different. The power calculation can be configured to measure
the bus voltage either at VIN+ (Supply Power) or at VIN– (Load Power). If the power being supplied by the power
supply is of interest, the Supply Power mode should be selected as the output mode setting. If the power being
consumed by the load is of interest, the Load Power mode should be selected as the output mode setting. Note
that the bus voltage measurement location is only available for the power calculation. For the Bus Voltage output
mode, the bus voltage is always measured at the VIN+ pin.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA223
17
INA223
SBOS528 – JUNE 2012
www.ti.com
Input Filtering
An obvious and straightforward location for filtering is at the output of the INA223. However, this location negates
the advantage of the low output impedance of the internal buffer. The only other option for filtering is at the input
pins of the INA223. Figure 35 shows a filter placed at the inputs pins.
CBYPASS
0.1µF
RSHUNT
Power
Supply
(0V to 26V)
Load
VS (Supply
Voltage)
INA223
RFILTER
” 10
RPULL-UP
4.7k
1/GAIN
VINVOUT
X
+
SCL
VIN+
Two-Wire
Interface
CFILTER - 0.1µF to 1µF
Ceramic Capacitor
SDA
A0
DISABLE
GND
Figure 35. Input Filter
The addition of external series resistance, though, creates an additional error that is not present under normal
operating conditions. An internal bias network at the input pins creates a mismatch in input bias currents when a
differential voltage is applied to the device’s input pins. This results in a mismatch of voltage drops on the input
lines due to the mismatch of input bias currents flowing through the additional external series filter resistors. This
creates a differential error voltage that subtracts from the voltage developed at the shunt resistor. The result is a
reduced differential voltage at the device input pins relative to the expected shunt voltage created by the load
current flowing through the shunt resistor. Without the additional series resistance, the mismatch in input bias
currents has little effect on the operation of the device.
The amount of variance in the differential voltage present directly at the input pins relative to the voltage
developed at the shunt resistor is based both on values of external series resistance as well as the internal input
resistors (RINT), which is based on the shunt voltage gain setting as shown in Table 5. The reduction of the shunt
voltage reaching the device input pins appears as a gain error when looking at the output voltage relative to the
shunt voltage. A factor can be calculated to determine the amount of gain error that is introduced by the addition
of external series resistance. The equation used to calculate the expected deviation from the shunt voltage to
what is seen at the device input pins is given in Equation 3.
(1250 ⋅ RINT)
Gain Error Factor =
(1250 ⋅ RS) + (1250 ⋅ RINT) + (RS ⋅ RINT)
Where
•
•
RINT is the internal input resistance.
RS is the external series resistance.
(3)
With the adjustment factor equation including the device internal input resistance, this factor will vary with each
gain setting.
Table 5. Internal Resistance Values
18
GAIN SETTING
RINT
20
600 kΩ
128
93 kΩ
300
40 kΩ
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA223
INA223
www.ti.com
SBOS528 – JUNE 2012
Using The INA223 with Common-Mode Transients Above 26 V
The INA223 is designed for a maximum common-mode voltage of 26 V. In applications that may be subjected to
transients above 26 V, the INA223 inputs must be protected. Figure 36 is the recommended method for
protecting the INA223 to these transients. Use only zener diodes or zener-type transient absorbers (also known
as a TransZorb™). Most other types of transient absorbers have an unacceptable time delay. The input resistors
shown in Figure 36 should be kept as small as possible (less than 10 Ω) to limit the effects this resistance has on
the gain, as discussed in the Input Filtering section.
CBYPASS
0.1µF
RSHUNT
Load
Power
Supply
VS (Supply
Voltage)
RPROTECT
≤ 10Ω
INA223
RPULL-UP
4.7kΩ
1/GAIN
VINVOUT
X
+
SCL
VIN+
Two-Wire
Interface
SDA
A0
DISABLE
GND
Figure 36. INA223 Transient Protection
Low-Side Current Sensing
The bus voltage of the INA223 is measured internally at the VIN+ pin, making it a high-side-only power monitor.
However, the INA223 can be used for low-side current sensing, as shown in Figure 37 (as the common-mode
voltage ranges from 0 V to 26 V).
CBYPASS
0.1µF
RSHUNT
VCM
+3.3V
Supply
Load
RPULL-UP
4.7k
Attenuator
VINVOUT
X
+
SCL
VIN+
Two-Wire
Interface
INA223
SDA
A0
GND
Figure 37. Low-Side Sensing with INA223
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA223
19
INA223
SBOS528 – JUNE 2012
www.ti.com
INA223 Recommended Layout
The recommended layout is shown in Figure 38. Pins 2 and 9 should be connected directly to Pins 1 and 10,
respectively. The shunt resistor should be placed as closely to the input pins, VIN+ and VIN-, to minimize any
parasitics or added resistance. Use a four-wire, or kelvin, connection to the shunt to achieve the most accurate
measurement across the shunt.
0603
(1)
VIN-
1
10
VIN+
VIN-(1)
2
9
VIN+(1)
GND
3
8
A0
VS
4
7
SDA
VOUT
5
6
SCL
See Application Information section for a description of how to connect input pins to the shunt resistor.
Figure 38. INA223 Recommended Layout
20
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA223
INA223
www.ti.com
SBOS528 – JUNE 2012
BUS OVERVIEW
The INA223 is compatible with both two-wire and SMBus interfaces. These protocols are essentially compatible
with one another. The two-wire interface is used throughout this data sheet as the primary example, with the
SMBus protocol specified only when a difference between the two systems is considered.
Two bidirectional lines, SCL and SDA, connect the INA223 to the bus. Both SCL and SDA are open-drain
connections.
The device that initiates the transfer is called a master, and the devices controlled by the master are slaves. The
bus must be controlled by a master device that generates the serial clock (SCL), controls the bus access, and
generates start and stop conditions.
To address a specific device, the master initiates a start condition by pulling the data signal line (SDA) from a
high to a low logic level while SCL is high. All slaves on the bus shift in the slave address byte on the rising edge
of SCL, with the last bit indicating whether a read or write operation is intended. During the ninth clock pulse, the
slave being addressed responds to the master by generating an acknowledge bit and pulling SDA low.
Data transfer is then initiated and eight bits of data are sent, followed by an acknowledge bit. During data
transfer, SDA must remain stable while SCL is high. Any change in SDA while SCL is high is interpreted as a
start or stop condition.
After all data have been transferred, the master generates a stop condition, indicated by pulling SDA from low to
high while SCL is high. The INA223 includes a 28-ms timeout on its interface to prevent locking up the bus.
Serial Bus Address
To communicate with the INA223, the master must first address slave devices through a slave address byte. The
slave address byte consists of seven address bits, and a direction bit that indicates the intent of executing a read
or write operation.
The INA223 has one address pin, A0. Table 6 describes the pin logic levels for each of the four possible
addresses. The state of the A0 pin is sampled on every bus communication and should be set before any activity
on the interface occurs. The address pins are read at the start of each communication event.
Table 6. INA223 Address Pins and Slave Addresses
A0
ADDRESS
GND
1000000
VS
1000001
SDA
1000010
SCL
1000011
Serial Interface
The INA223 operates only as a slave device on both the two-wire bus and SMBus. Connections to the bus are
made through the open-drain I/O lines, SDA and SCL. The SDA and SCL pins feature integrated spike
suppression filters and Schmitt triggers to minimize the effects of input spikes and bus noise. The INA223
supports the transmission protocol for fast (1 kHz to 400 kHz) and high-speed (1 kHz to 3.4 MHz) modes. All
data bytes are transmitted most significant byte first.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA223
21
INA223
SBOS528 – JUNE 2012
www.ti.com
GENERAL CALL
The INA223 responds to three unique two-wire general call commands. A response occurs to a general call
address (0000000) if the eighth bit is '0'. The device acknowledges the general call address and responds to
commands based on the second byte. The three commands that the INA223 responds to are:
• General Call Reset (06h)
• General Call Enable (81h)
• General Call Disable (82h)
The INA223 responds to the General Call Reset by resetting all of the Configuration Registers settings to the
respective default power-on values. The INA223 responds to a General Call Enable or General Call Disable by
entering into or exiting from a disabled state. The INA223 can also be enabled and disabled by setting or clearing
the enable/disable mode (EN) bit in the Configuration Register. The General Call Enable and General Call
Disable commands allow for a single command to place multiple connected INA223 devices into either an
enabled or disabled state.
WRITING TO AND READING FROM THE INA223
The INA223 has a single configuration register. This register is used to configure the INA223 based on how the
device is to be used. This register can also be read to determine the register contents and the current device
configuration.
Writing to the Configuration Register in the INA223 begins with the first byte transmitted by the master. This byte
is the slave address, with the R/W bit low. The INA223 then acknowledges receipt of a valid address. The next
two bytes are written to the register addressed by the register pointer. The INA223 acknowledges receipt of each
data byte. The master may terminate data transfer by generating a start or stop condition.
When reading the Configuration Register in the INA223, the communication sequence begins the same with the
first byte being transmitted by the master. This byte is the slave address, with the R/W bit high. The INA223 then
acknowledges receipt of a valid address. The next byte is transmitted by the slave and is the most significant
byte of the register indicated by the register pointer. This byte is followed by an acknowledge bit from the master;
then the slave transmits the least significant byte. The master acknowledges receipt of the data byte. The master
may terminate data transfer by generating a not-acknowledge bit after receiving any data byte, or by generating a
start or stop condition.
22
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA223
INA223
www.ti.com
SBOS528 – JUNE 2012
Figure 39 and Figure 40 show read and write operation timing diagrams, respectively. Note that register bytes
are sent most-significant byte first, followed by the least significant byte.
1
9
1
9
1
9
1
9
SCL
SDA
1
0
0
0
0
A1
A0
Start By
Master
R/W
P7
P6
P5
P4
ACK By
INA223
Frame 1 Two-Wire Slave Address Byte
(1)
P3
P2
P1
P0
D15 D14 D13 D12 D11 D10 D9
ACK By
INA223
(1)
Frame 2 Register Pointer Byte
D8
D7
D6
D5
D4
D3
D2
D1
D0
ACK By Stop By
INA223 Master
ACK By
INA223
Frame 3 Data MSByte
Frame 4 Data LSByte
The value of the Slave Address Byte is determined by the setting of the A0 pin. Refer to Table 1.
Figure 39. Timing Diagram for Write Word Format
1
9
1
9
1
9
SCL
1
SDA
0
0
0
0
A1 A0 R/W
Start By
Master
D15 D14 D13 D12 D11 D10 D9 D8
ACK By
INA223
Frame 1 Two-Wire
Slave Address Byte
(1)
From
INA223
D7
D6
D5
D4
D3
D2
D1 D0
From
INA223
ACK By
Master
Frame 2 Data MSByte
No ACK By Stop By
(2)
Master
Master
Frame 3 Data LSByte
(1)
The value of the Slave Address Byte is determined by the setting of the A0 pin. Refer to Table 1.
(2)
ACK by master can also be sent.
Figure 40. Timing Diagram for Read Word Format
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA223
23
INA223
SBOS528 – JUNE 2012
www.ti.com
High-Speed Two-Wire Mode
When the bus is idle, both the SDA and SCL lines are pulled high by the pull-up devices. The master generates
a start condition followed by a valid serial byte containing high-speed (HS) master code 00001XXX. This
transmission is made in either fast (400 kHz) or standard (100 kHz) (F/S) mode at no more than 400 kHz. The
INA223 does not acknowledge the HS master code, but recognizes it and switches its internal filters to support
3.4-MHz operation.
The master then generates a repeated start condition (a repeated start condition has the same timing as the start
condition). After this repeated start condition, the protocol is the same as F/S mode, except that transmission
speeds up to 3.4 MHz are allowed. Instead of using a stop condition, repeated start conditions should be used to
secure the bus in HS-mode. A stop condition ends the HS-mode and switches all the internal filters of the
INA223 to support the F/S mode. Figure 41 illustrates the bus timing. Corresponding definitions are listed in
Table 7.
t(LOW)
tR
t(HDSTA)
tF
SCL
t(HIGH)
t(HDSTA)
t(HDDAT)
t(SUSTO)
t(SUSTA)
t(SUDAT)
SDA
t(BUF)
P
S
P
S
Figure 41. Bus Timing Diagram
Table 7. Bus Timing Diagram Definitions
FAST MODE
SYMBOL
DESCRIPTION
HIGH-SPEED MODE
MIN
MAX
MIN
MAX
0.001
0.4
0.001
3.4
UNITS
f(SCL)
SCL operating frequency
t(BUF)
Bus free time between stop and start conditions
600
160
ns
t(HDSTA)
Hold time after repeated start condition.
After this period, the first clock is generated.
100
100
ns
t(SUSTA)
Repeated start condition setup time
100
100
ns
t(SUSTO)
Stop condition setup time
100
100
ns
t(HDDAT)
Data hold time
15
15
ns
t(SUDAT)
Data setup time
100
10
ns
t(LOW)
SCL clock low period
1300
160
ns
t(HIGH)
SCL clock high period
600
60
ns
tF
Clock/Data fall time
300
160
ns
Clock/Data rise time
300
160
ns
tR
24
Clock/Data rise time for SCLK ≤ 100 kHz
Submit Documentation Feedback
1000
MHz
ns
Copyright © 2012, Texas Instruments Incorporated
Product Folder Link(s): INA223
PACKAGE OPTION ADDENDUM
www.ti.com
27-Jun-2012
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
INA223AIDSKR
ACTIVE
SON
DSK
10
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
INA223AIDSKT
ACTIVE
SON
DSK
10
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
(3)
Samples
(Requires Login)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Aug-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
INA223AIDSKR
SON
DSK
10
3000
330.0
8.4
2.8
2.8
1.0
4.0
8.0
Q2
INA223AIDSKT
SON
DSK
10
250
180.0
8.4
2.8
2.8
1.0
4.0
8.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Aug-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
INA223AIDSKR
SON
DSK
10
3000
367.0
367.0
35.0
INA223AIDSKT
SON
DSK
10
250
210.0
185.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated