LTM4627 15A DC/DC µModule Regulator FEATURES DESCRIPTION n The LTM®4627 is a complete 15A output high efficiency switch mode DC/DC power supply. Included in the package are the switching controller, power FETs, inductor and compensation components. Operating over an input voltage range from 4.5V to 20V, the LTM4627 supports an output voltage range of 0.6V to 5V, set by a single external resistor. Only a few input and output capacitors are needed. n n n n n n n n n n n n n Complete 15A Switch Mode Power Supply Wide Input Voltage Range: 4.5V to 20V 0.6V to 5V Output Range ±1.5% Total DC Output Error (–40°C to 125°C) Differential Remote Sense Amplifier for Precision Regulation Current Mode Control/ Fast Transient Response Frequency Synchronization Parallel Current Sharing (Up to 60A) Selectable Pulse-Skipping or Burst Mode® Operation Soft-Start/Voltage Tracking Up to 93% Efficiency (12VIN, 3.3VOUT) Overcurrent Foldback Protection Output Overvoltage Protection Small Surface Mount Footprint, Low Profile 15mm × 15mm × 4.32mm LGA Package APPLICATIONS n n n n Current mode operation allows precision current sharing of up to four LTM4627 regulators to obtain 60A output. High switching frequency and a current mode architecture enable a very fast transient response to line and load changes without sacrificing stability. The device supports frequency synchronization, multiphase/current sharing operation, Burst Mode operation and output voltage tracking for supply rail sequencing. The LTM4627 is offered in a thermally enhanced 15mm × 15mm × 4.32mm LGA package. The LTM4627 is PB-free and RoHS compliant. L, LT, LTC, LTM, Linear Technology, the Linear logo, Burst Mode and μModule are registered trademarks of Linear Technology Corporation. PolyPhase is a registered trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. Protected by U.S. Patents, including 5481178, 5847554, 6580258, 6304066, 6476589, 6774611, 6677210. Telecom Servers and Networking Equipment ATCA and Storage Cards Industrial Equipment Medical Systems TYPICAL APPLICATION 1.2V, 15A DC/DC μModule® Regulator 95 22μF 16V ×3 90 150pF 10k 0.1μF VIN EXTVCC INTVCC PGOOD COMP VOUT TRACK/SS LTM4627 RUN MODE_PLLIN SGND * SEE TABLE 4 ** SEE TABLE 1 + VOUT_LCL DIFF_OUT 82pF VOSNS+ VOSNS– fSET 100k 85 GND 470μF 6.3V VOUT 1.2V 15A 100μF* 6.3V EFFICIENCY (%) VIN 4.5V TO 16V Efficiency vs Load Current 80 75 70 65 60 VFB 12VIN, 1.2VOUT 5VIN, 1.2VOUT 55 RFB** 60.4k 50 0 4627 TA01a 2 4 6 10 12 8 LOAD CURRENT (A) 14 16 4627 TA01b 4627f 1 LTM4627 ABSOLUTE MAXIMUM RATINGS PIN CONFIGURATION (Note 1) VIN ............................................................. –0.3V to 22V INTVCC, VOUT (VOUT ≤ 3.3V with DIFF AMP), VOUT_LCL, PGOOD, EXTVCC ....... –0.3V to 6V MODE_PLLIN, fSET, TRACK/SS, VOSNS –, VOSNS+, DIFF_OUT...................–0.3V to INTVCC COMP, VFB ................................................ –0.3V to 2.7V RUN (Note 5) ............................................... –0.3V to 5V INTVCC Peak Output Current (Note 6) ..................100mA Internal Operating Temperature Range (Note 2).................................................. –40°C to 125°C Storage Temperature Range .................. –55°C to 125°C Reflow (Peak Body) Temperature .......................... 250°C 1 2 3 VIN TOP VIEW MODE_PLLIN INTVCC TRACK/SS 4 5 6 7 8 9 10 COMP 11 12 A VIN RUN fSET B C INTVCC D E F EXTVCC PGOOD VFB G PGOOD GND H VOUT SGND J VOSNS+ K DIFF_OUT L VOUT_LCL M VOSNS– VOUT LGA PACKAGE 133-LEAD (15mm s 15mm s 4.32mm) TJ(MAX) = 125°C, θJA = 13°C/W, θJCbottom = 2.3°C/W, θJCtop = 11°C/W to 13°C/W, θJA DERIVED FROM 95mm × 76mm PCB WITH 4 LAYERS; WEIGHT = 2.6g θ VALUES DETERMINED PER JESD51-12 ORDER INFORMATION LEAD FREE FINISH TRAY PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTM4627EV#PBF LTM4627EV#PBF LTM4627V 133-Lead (15mm × 15mm × 4.32mm) LGA –40°C to 125°C LTM4627IV#PBF LTM4627IV#PBF LTM4627V 133-Lead (15mm × 15mm × 4.32mm) LGA –40°C to 125°C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ This product is only offered in trays. For more information go to: http://www.linear.com/packaging/ ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full internal operating temperature range, otherwise specifications are at TA = 25°C (Note 2), VIN = 12V, per the typical application in Figure 18. SYMBOL PARAMETER VIN Input DC Voltage VOUT(DC) Output Voltage, Total Variation with Line and Load CONDITIONS CIN = 22μF × 3 COUT = 100μF Ceramic, 470μF POSCAP RFB = 40.2k, MODE_PLLIN = GND VIN = 5V to 20V, IOUT = 0A to 15A (Note 4) MIN l 4.5 l 1.477 1.1 TYP MAX UNITS 20 V 1.50 1.523 V 1.25 1.4 V Input Specifications VRUN RUN Pin On Threshold VRUNHYS RUN Pin On Hysteresis VRUN Rising 130 mV 4627f 2 LTM4627 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full internal operating temperature range, otherwise specifications are at TA = 25°C (Note 2), VIN = 12V, per the typical application in Figure 18. SYMBOL PARAMETER CONDITIONS IQ(VIN) Input Supply Bias Current VIN = 12V, VOUT = 1.5V, Burst Mode Operation, IOUT = 0.1A VIN = 12V, VOUT = 1.5V, Pulse-Skipping Mode, IOUT = 0.1A VIN = 12V, VOUT = 1.5V, Switching Continuous, IOUT = 0.1A Shutdown, RUN = 0, VIN = 12V IS(VIN) Input Supply Current VIN = 5V, VOUT = 1.5V, IOUT = 15A VIN = 12V, VOUT = 1.5V, IOUT = 15A MIN TYP MAX 17 25 54 40 UNITS mA mA mA μA 5.05 2.13 A A Output Specifications IOUT(DC) Output Continuous Current Range VIN = 12V, VOUT = 1.5V (Note 4) 0 15 A ΔVOUT (Line) VOUT Line Regulation Accuracy VOUT = 1.5V, VIN from 4.5V to 20V IOUT = 0A l 0.02 0.06 %/V ΔVOUT (Load) VOUT Load Regulation Accuracy VOUT = 1.5V, IOUT = 0A to 15A, VIN = 12V (Note 4) l 0.2 0.45 % VOUT(AC) Output Ripple Voltage IOUT = 0A, COUT = 100μF Ceramic, 470μF POSCAP VIN = 12V, VOUT = 1.5V 15 mVP-P ΔVOUT(START) Turn-On Overshoot COUT = 100μF Ceramic, 470μF POSCAP, VOUT = 1.5V, IOUT = 0A, VIN = 12V 20 mV tSTART Turn-On Time COUT = 100μF Ceramic, 470μF POSCAP, No Load, TRACK/SS = 0.001μF, VIN = 12V 50 ms ΔVOUTLS Peak Deviation for Dynamic Load Load: 0% to 50% to 0% of Full Load COUT = 100μF Ceramic, 470μF POSCAP, VIN = 12V, VOUT = 1.5V 60 mV tSETTLE Settling Time for Dynamic Load Step Load: 0% to 50% to 0% of Full Load VIN = 5V, COUT = 100μF Ceramic, 470μF POSCAP 20 μs IOUTPK Output Current Limit VIN = 12V, VOUT = 1.5V VIN = 5V, VOUT = 1.5V 25 25 A A VFB Voltage at VFB Pin IOUT = 0A, VOUT = 1.5V IFB Current at VFB Pin (Note 7) VOVL Feedback Overvoltage Lockout ITRACK/SS Track Pin Soft-Start Pull-Up Current TRACK/SS = 0V tON(MIN) Minimum On-Time (Note 3) RFBHI Resistor Between VOUT_LCL and VFB Pins VOSNS+, VOSNS– CM RANGE Common Mode Input Range VDIFF_OUT(MAX) Maximum DIFF_OUT Voltage IDIFF_OUT = 300μA Control Section l l 0.594 0.60 0.606 V –12 –25 nA 0.65 0.67 0.69 V 1.0 1.2 1.4 μA 90 60.05 VIN = 12V, Run > 1.4V 60.40 0 ns 60.75 4 INTVCC – 1.4 kΩ V V VOSNS+ = VDIFF_OUT = 1.5V, IDIFF_OUT = 100μA VOS Input Offset Voltage 2 AV Differential Gain 1 SR Slew Rate 2 V/μs GBP Gain Bandwidth Product 3 MHz CMRR Common Mode Rejection (Note 7) 60 dB IDIFF_OUT DIFF_OUT Current Sourcing 2 mV V/V mA 4627f 3 LTM4627 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full internal operating temperature range, otherwise specifications are at TA = 25°C (Note 2), VIN = 12V, per the typical application in Figure 18. SYMBOL PARAMETER CONDITIONS PSRR Power Supply Rejection Ratio 5V < VIN < 20V (Note 7) MIN TYP 100 MAX UNITS dB RIN Input Resistance VOSNS+ to GND 80 kΩ VPGOOD PGOOD Trip Level VFB With Respect to Set Output VFB Ramping Negative VFB Ramping Positive –10 10 % % VPGL PGOOD Voltage Low IPGOOD = 2mA 0.1 0.3 V 5 5.2 V INTVCC Linear Regulator VINTVCC Internal VCC Voltage VINTVCC Load Reg INTVCC Load Regulation 6V < VIN < 20V 4.8 ICC = 0 to 50mA VEXTVCC External VCC Switchover EXTVCC Ramping Positive VLDO Ext EXTVCC Voltage Drop ICC = 25mA, VEXTVCC = 5V l 4.5 0.5 % 4.7 V 50 100 mV 800 kHz Oscillator and Phase-Locked Loop fSYNC SYNC Capture Range 250 Frequency Nominal Nominal Frequency VfSET = 1.2V 450 500 550 kHz Frequency Low Lowest Frequency VfSET = 1V 350 400 450 kHz Frequency High Highest Frequency VfSET ≥ 2.4V 700 770 850 kHz IFREQ Frequency Set Current 9 10 11 μA RMODE_PLLIN Mode_PLLIN Input Resistance VIH_MODE_PLLIN Clock Input Level High VIL_MODE_PLLIN Clock Input Level Low Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LTM4627 is tested under pulsed load conditions such that TJ ≈ TA. The LTM4627E is guaranteed to meet performance specifications over the 0°C to 125°C internal operating temperature range. Specifications over the full –40°C to 125°C internal operating temperature range are assured by design, characterization and correlation with statistical process controls. The LTM4627I is guaranteed to meet specifications over the full –40°C to 125°C internal operating temperature range. Note that the 250 kΩ 2.0 V 0.8 V maximum ambient temperature consistent with these specifications is determined by specific operating conditions in conjunction with board layout, the rated package thermal resistance and other environmental factors. Note 3: The minimum on-time condition is specified for a peak-to-peak inductor ripple current of ~40% of IMAX Load. (See the Applications Information section) Note 4: See output current derating curves for different VIN, VOUT and TA. Note 5: Limit current into the RUN pin to less than 2mA. Note 6: Guaranteed by design. Note 7: 100% tested at wafer level. 4627f 4 LTM4627 TYPICAL PERFORMANCE CHARACTERISTICS Efficiency vs Load Current with 8VIN 100 95 95 90 90 90 85 85 85 80 75 70 1VOUT AT 400kHz 1.2VOUT AT 400kHz 1.5VOUT AT 400kHz 2.5VOUT AT 400kHz 3.3VOUT AT 650kHz 60 55 50 0 2 4 6 10 12 8 LOAD CURRENT (A) 14 80 75 70 1VOUT AT 400kHz 1.2VOUT AT 400kHz 1.5VOUT AT 400kHz 2.5VOUT AT 500kHz 3.3VOUT AT 600kHz 5VOUT AT 600kHz 65 60 55 50 16 0 2 4 6 10 12 8 LOAD CURRENT (A) 4627 G01 14 80 75 70 1VOUT AT 400kHz 1.2VOUT AT 400kHz 1.5VOUT AT 400kHz 2.5VOUT AT 650kHz 3.3VOUT AT 650kHz 5VOUT AT 700kHz 65 60 55 16 50 0 2 4 6 10 12 8 LOAD CURRENT (A) 4627 G02 Burst Mode Efficiency 14 16 4627 G03 Pulse-Skipping Mode Efficiency 1.0 1.0V Transient Response 1.0 5VIN, 2.5VOUT Burst Mode OPERATION 0.9 5VIN, 2.5VOUT PULSE-SKIPPING MODE 0.9 EFFICIENCY (%) 0.8 12VIN, 2.5VOUT Burst Mode OPERATION 0.7 0.6 0.5 0.4 EFFICIENCY (%) 100 95 65 EFFICIENCY (%) Efficiency vs Load Current with 12VIN 100 EFFICIENCY (%) EFFICIENCY (%) Efficiency vs Load Current with 5VIN 50mV/DIV 0.8 0.7 7.5A LOAD STEP 0.6 12VIN, 2.5VOUT PULSE-SKIPPING MODE 0.5 0.1 0.2 1 0.5 1.5 LOAD CURRENT (A) 2 0.4 100μs/DIV VIN = 12V, VOUT = 1.0V, CFF = 82pF, CCOMP = 33pF OUTPUT CAPACITOR = 5 s 100μF CERAMIC X5R 0.1 0.2 1 0.5 1.5 LOAD CURRENT (A) 4627 G04 2 4627 G05 1.2V Transient Response 1.5V Transient Response 1.8V Transient Response 50mV/DIV 50mV/DIV 50mV/DIV 7.5A LOAD STEP 7.5A LOAD STEP 7.5A LOAD STEP 100μs/DIV 4627 G07 VIN = 12V, VOUT = 1.2V, CFF = 82pF, CCOMP = 33pF OUTPUT CAPACITOR = 5 s 100μF CERAMIC X5R 4627 G06 100μs/DIV 4627 G08 VIN = 12V, VOUT = 1.5V, CFF = 82pF, CCOMP = 33pF OUTPUT CAPACITOR = 5 s 100μF CERAMIC X5R 100μs/DIV 4627 G09 VIN = 12V, VOUT = 1.8V, CFF = 82pF, CCOMP = 33pF OUTPUT CAPACITOR = 4 s 100μF CERAMIC X5R 4627f 5 LTM4627 TYPICAL PERFORMANCE CHARACTERISTICS 2.5V Transient Response 3.3V Transient Response 5.0V Transient Response 50mV/DIV 50mV/DIV 50mV/DIV 7.5A LOAD STEP 7.5A LOAD STEP 7.5A LOAD STEP 100μs/DIV 4627 G10 100μs/DIV 4627 G12 VIN = 12V, VOUT = 2.5V, CFF = 82pF, CCOMP = 33pF OUTPUT CAPACITOR = 4 s 100μF CERAMIC X5R VIN = 12V, VOUT = 3.3V, CFF = 82pF, CCOMP = 33pF OUTPUT CAPACITOR = 2 s 100μF CERAMIC X5R VIN = 12V, VOUT = 5V, CFF = 82pF, CCOMP = 33pF OUTPUT CAPACITOR = 2 s 100μF CERAMIC X5R Start-Up with Soft-Start Short-Circuit Protection No Load Short-Circuit Protection 15A Load VOUT VOUT VOUT 100μs/DIV 4627 G11 500mV/DIV 500mV/DIV 500mV/DIV IIN IOUT 5A/DIV 1A/DIV 1A/DIV IIN 100μs/DIV 4ms/DIV 4627 G13 VIN = 12V, VOUT = 1.5V, IOUT = 15A INPUT CAP 150μF SANYO ELECTROLYTIC CAP AND 22μF s 2 X5R CERAMIC CAP OUTPUT CAP 1 s 100μF X5R CERAMIC AND 470μF 0.1μF CAP FROM TRACK/SS TO GND VIN = 12V, VOUT = 1.5V, IOUT = 0A 4627 G14 4ms/DIV 4627 G15 VIN = 12V, VOUT = 1.5V, IOUT = 15A PIN FUNCTIONS VIN (A1-A6, B1-B6, C1-C6): Power Input Pins. Apply input voltage between these pins and GND pins. Recommend placing input decoupling capacitance directly between VIN pins and GND pins. PGOOD (F11, G12): Output Voltage Power Good Indicator. Open-drain logic output that is pulled to ground when the output voltage exceeds a ±10% regulation window. Both pins are tied together internally. VOUT (J1-J10, K1-K11, L1-L11, M1-M11): Power Output Pins. Apply output load between these pins and GND pins. Recommend placing output decoupling capacitance directly between these pins and GND pins. Review Table 4. SGND (G11, H11, H12): Signal Ground Pin. Return ground path for all analog and low power circuitry. Tie a single connection to the output capacitor GND in the application. See layout guidelines in Figure 17. GND (B7, B9, C7, C9, D1-D6, D8, E1-E7, E9, F1-F9, G1-G9, H1-H9): Power Ground Pins for Both Input and Output Returns. 4627f 6 LTM4627 PIN FUNCTIONS MODE_PLLIN (A8): Forced Continuous Mode, Burst Mode Operation, or Pulse-Skipping Mode Selection Pin and External Synchronization Input to Phase Detector Pin. Connect this pin to INTVCC to enable pulse-skipping mode of operation. Connect to ground to enable forced continuous mode of operation. Floating this pin will enable Burst Mode operation. A clock on this pin will enable synchronization with forced continuous operation. See the Applications Information section. RUN: (A10) Run Control Pin. A voltage above 1.4V will turn on the module. A 5.1V Zener diode to ground is internal to the module for limiting the voltage on the RUN pin to 5V, and allowing a pull-up resistor to VIN for enabling the device. Limit current into the RUN pin to ≤ 2mA. fSET (B12): A resistor can be applied from this pin to ground to set the operating frequency, or a DC voltage can be applied to set the frequency. See the Applications Information section. EXTVCC (E12): External power input to an internal control switch allows an external source greater than 4.7V, but less than 6V to supply IC power and bypass the internal INTVCC LDO. See the Applications Information section. TRACK/SS (A9): Output Voltage Tracking Pin and SoftStart Inputs. The pin has a 1.2μA pull-up current source. A capacitor from this pin to ground will set a soft-start ramp rate. In tracking, the regulator output can be tracked to a different voltage. The different voltage is applied to a voltage divider then the slave output’s track pin. This voltage divider is equal to the slave output’s feedback divider for coincidental tracking. See the Applications Information section. VOUT_LCL: (L12) This pin connects to VOUT through a 1M resistor, and to VFB with a 60.4k resistor. The remote sense amplifier output DIFF_OUT is connected to VOUT_LCL, and drives the 60.4k top feedback resistor in remote sensing applications. When the remote sense amplifier is used, DIFF_OUT effectively eliminates the 1MΩ from VOUT to VOUT_LCL. When the remote sense amplifier is not used, then connect VOUT_LCL to VOUT directly. VFB (F12): The Negative Input of the Error Amplifier. Internally, this pin is connected to VOUT_LCL with a 60.4k precision resistor. Different output voltages can be programmed with an additional resistor between VFB and ground pins. In PolyPhase® operation, tying the VFB pins together allows for parallel operation. See the Applications Information section for details. COMP (A11): Current Control Threshold and Error Amplifier Compensation Point. The current comparator threshold increases with this control voltage. Tie all COMP pins together for parallel operation. The device is internally compensated. INTVCC: (A7, D9) Internal 5V LDO for Driving the Control Circuitry and the Power MOSFET Drivers. Both pins are internally connected. The 5V LDO has a 100mA current limit. VOSNS+: (J12) (+) Input to the Remote Sense Amplifier. This pin connects to the output remote sense point. The remote sense amplifier is used for VOUT ≤ 3.3V. VOSNS–: (M12) (–) Input to the Remote Sense Amplifier. This pin connects to the ground remote sense point. The remote sense amplifier is used for VOUT ≤ 3.3V. DIFF_OUT: (K12) Output of the Remote Sense Amplifier. This pin connects to the VOUT_LCL pin for remote sense applications. Otherwise float when not used. MTP1, MTP2, MTP3, MTP4, MTP5, MTP6, MTP7, MTP8 (A12, B11, C10, C11, C12, D10, D11, D12): Extra mounting pads used for increased solder integrity strength. Leave floating. 4627f 7 LTM4627 BLOCK DIAGRAM INTVCC VOUT_LCL 1M VIN R1 VOUT 10k PGOOD > 1.4V = ON < 1.1V = OFF MAX = 5V VIN RUN 1.5μF 5.1V R2 + VIN 4.5V TO 20V CIN COMP 60.4k M1 INTERNAL COMP 0.4μH 10μF VFB VOUT 1V 15A VOUT POWER CONTROL SGND M2 COUT + fSET INTERNAL LOOP FILTER INTVCC TRACK/SS MODE_PLLIN + 250k – INTVCC DIFF AMP VOSNS– + C SOFT-START GND RfSET 100k – 90.9k VOSNS+ C DIFF_OUT EXTVCC 4627 F01 Figure 1. Simplified LTM4627 Block Diagram DECOUPLING REQUIREMENTS TA = 25°C. Use Figure 1 configuration. SYMBOL PARAMETER CONDITIONS CIN External Input Capacitor Requirement (VIN = 4.5V to 20V, VOUT = 1.5V) IOUT = 15A COUT External Output Capacitor Requirement (VIN = 4.5V to 20V, VOUT = 1.5V) IOUT = 15A MIN TYP 66 MAX UNITS μF 200 μF 4627f 8 LTM4627 OPERATION Power Module Description The LTM4627 is a high performance single output standalone nonisolated switching mode DC/DC power supply. It can provide a 15A output with few external input and output capacitors. This module provides precisely regulated output voltages programmable via external resistors from 0.6VDC to 5VDC over a 4.5V to 20V input range. The typical application schematic is shown in Figure 18. The LTM4627 has an integrated constant-frequency current mode regulator, power MOSFETs, 0.4μH inductor, and other supporting discrete components. The switching frequency range is from 400kHz to 800kHz, and the typical operating frequency is 500kHz. For switching noise-sensitive applications, it can be externally synchronized from 400kHz to 800kHz. A single resistor is used to program the frequency. See the Applications Information section. With current mode control and internal feedback loop compensation, the LTM4627 module has sufficient stability margins and good transient performance with a wide range of output capacitors, even with all ceramic output capacitors. Current mode control provides cycle-by-cycle fast current limit in an overcurrent condition. An internal overvoltage monitor protects the output voltage in the event of an overvoltage >10%. The top MOSFET is turned off and the bottom MOSFET is turned on until the output is cleared. Pulling the RUN pin below 1.1V forces the regulator into a shutdown state. The TRACK/SS pin is used for programming the output voltage ramp and voltage tracking during start-up. See the Application Information section. The LTM4627 is internally compensated to be stable over all operating conditions. Table 4 provides a guideline for input and output capacitances for several operating conditions. The Linear Technology μModule Power Design Tool will be provided for transient and stability analysis. The VFB pin is used to program the output voltage with a single external resistor to ground. A remote sense amplifier is provided for accurately sensing output voltages ≤3.3V at the load point. Multiphase operation can be easily employed with the synchronization inputs using an external clock source. See application examples. High efficiency at light loads can be accomplished with selectable Burst Mode operation using the MODE_PLLIN pin. These light load features will accommodate battery operation. Efficiency graphs are provided for light load operation in the Typical Performance Characteristics section. 4627f 9 LTM4627 APPLICATIONS INFORMATION The typical LTM4627 application circuit is shown in Figure 18. External component selection is primarily determined by the maximum load current and output voltage. Refer to Table 4 for specific external capacitor requirements for particular applications. VIN to VOUT Step-Down Ratios There are restrictions in the VIN to VOUT step-down ratio that can be achieved for a given input voltage. The VIN to VOUT minimum dropout is a function of load current and at very low input voltage and high duty cycle applications output power may be limited as the internal top power MOSFET is not rated for 15A operation at higher ambient temperatures. At very low duty cycles the minimum 90ns on-time must be maintained. See the Frequency Adjustment section and temperature derating curves. Output Voltage Programming The PWM controller has an internal 0.6V ±1% reference voltage. As shown in the Block Diagram, a 60.4k internal feedback resistor connects the VOUT_LCL and VFB pins together. When the remote sense amplifier is used, then DIFF_OUT is connected to the VOUT_LCL pin. If the remote sense amplifier is not used, then VOUT_LCL connects to VOUT. The output voltage will default to 0.6V with no feedback resistor. Adding a resistor RFB from VFB to ground programs the output voltage: VOUT = 0.6V • 60.4k + RFB RFB Table 1. VFB Resistor Table vs Various Output Voltages VOUT (V) RFB (k) 0.6 1.0 1.2 1.5 1.8 2.5 3.3 5.0 Open 90.9 60.4 40.2 30.1 19.1 13.3 8.25 For parallel operation of N LTM4627s, the following equation can be used to solve for RFB: 60.4 / N RFB = VOUT –1 0.6 Tie the VFB pins together for each parallel output. The COMP pins must be tied together also. Input Capacitors The LTM4627 module should be connected to a low AC-impedance DC source. Additional input capacitors are needed for the RMS input ripple current rating. The ICIN(RMS) equation which follows can be used to calculate the input capacitor requirement. Typically 22μF X7R ceramics are a good choice with RMS ripple current ratings of ~ 2A each. A 47μF to 100μF surface mount aluminum electrolytic bulk capacitor can be used for more input bulk capacitance. This bulk input capacitor is only needed if the input source impedance is compromised by long inductive leads, traces or not enough source capacitance. If low impedance power planes are used, then this bulk capacitor is not needed. For a buck converter, the switching duty cycle can be estimated as: D= VOUT VIN Without considering the inductor ripple current, for each output, the RMS current of the input capacitor can be estimated as: IOUT(MAX) I CIN(RMS)= • D • (1– D) η% In the previous equation, η% is the estimated efficiency of the power module. The bulk capacitor can be a switcher-rated electrolytic aluminum capacitor or a Polymer capacitor. 4627f 10 LTM4627 APPLICATIONS INFORMATION Output Capacitors The LTM4627 is designed for low output voltage ripple noise. The bulk output capacitors defined as COUT are chosen with low enough effective series resistance (ESR) to meet the output voltage ripple and transient requirements. COUT can be a low ESR tantalum capacitor, low ESR Polymer capacitor or ceramic capacitors. The typical output capacitance range is from 200μF to 800μF. Additional output filtering may be required by the system designer if further reduction of output ripple or dynamic transient spikes is required. Table 4 shows a matrix of different output voltages and output capacitors to minimize the voltage droop and overshoot during a 7A/μs transient. The table optimizes total equivalent ESR and total bulk capacitance to optimize the transient performance. Stability criteria are considered in the Table 4 matrix, and the Linear Technology μModule Power Design Tool will be provided for stability analysis. Multiphase operation will reduce effective output ripple as a function of the number of phases. Application Note 77 discusses this noise reduction versus output ripple current cancellation, but the output capacitance should be considered carefully as a function of stability and transient response. The Linear Technology μModule Power Design Tool can calculate the output ripple reduction as the number of implemented phase’s increases by N times. Burst Mode Operation The LTM4627 is capable of Burst Mode operation in which the power MOSFETs operate intermittently based on load demand, thus saving quiescent current. For applications where maximizing the efficiency at very light loads is a high priority, Burst Mode operation should be applied. To enable Burst Mode operation, simply float the MODE_PLLIN pin. During Burst Mode operation, the peak current of the inductor is set to approximately 30% of the maximum peak current value in normal operation even though the voltage at the COMP pin indicates a lower value. The voltage at the COMP pin drops when the inductor’s average current is greater than the load requirement. As the COMP voltage drops below 0.5V, the burst comparator trips, causing the internal sleep line to go high and turn off both power MOSFETs. In sleep mode, the internal circuitry is partially turned off, reducing the quiescent current. The load current is now being supplied from the output capacitors. When the output voltage drops, causing COMP to rise, the internal sleep line goes low, and the LTM4627 resumes normal operation. The next oscillator cycle will turn on the top power MOSFET and the switching cycle repeats. Pulse-Skipping Mode Operation In applications where low output ripple and high efficiency at intermediate currents are desired, pulse-skipping mode should be used. Pulse-skipping operation allows the LTM4627 to skip cycles at low output loads, thus increasing efficiency by reducing switching loss. Tying the MODE_PLLIN pin to INTVCC enables pulse-skipping operation. With pulse-skipping mode at light load, the internal current comparator may remain tripped for several cycles, thus skipping operation cycles. This mode has lower ripple than Burst Mode operation and maintains a higher frequency operation than Burst Mode operation. Forced Continuous Operation In applications where fixed frequency operation is more critical than low current efficiency, and where the lowest output ripple is desired, forced continuous operation should be used. Forced continuous operation can be enabled by tying the MODE_PLLIN pin to ground. In this mode, inductor current is allowed to reverse during low output loads, the COMP voltage is in control of the current comparator threshold throughout, and the top MOSFET always turns on with each oscillator pulse. During start-up, forced continuous mode is disabled and inductor current is prevented from reversing until the LTM4627’s output voltage is in regulation. 4627f 11 LTM4627 APPLICATIONS INFORMATION Multiphase Operation For outputs that demand more than 15A of load current, multiple LTM4627 devices can be paralleled to provide more output current without increasing input and output voltage ripple. The MODE_PLLIN pin allows the LTM4627 to be synchronized to an external clock (between 400kHz to 800kHz) and the internal phase-locked loop allows the LTM4627 to lock onto input clock phase as well. The fSET resistor is selected for normal frequency, then the incoming clock can synchronize the device over the specified range. See Figure 20 for a synchronizing example circuit. A multiphase power supply significantly reduces the amount of ripple current in both the input and output capacitors. The RMS input ripple current is reduced by, and the effective ripple frequency is multiplied by, the number of phases used (assuming that the input voltage is greater than the number of phases used times the output voltage). The output ripple amplitude is also reduced by the number of phases used. See Application Note 77. The LTM4627 device is an inherently current mode controlled device, so parallel modules will have good current sharing. This will balance the thermals in the design. Tie the COMP and VFB pins of each LTM4627 together to share the current evenly. Figure 20 shows a schematic of the parallel design. Input RMS Ripple Current Cancellation Application Note 77 provides a detailed explanation of multiphase operation. The input RMS ripple current cancellation mathematical derivations are presented, and a graph is displayed representing the RMS ripple current reduction as a function of the number of interleaved phases (see Figure 2). PLL, Frequency Adjustment and Synchronization The LTM4627 switching frequency is set by a resistor (RfSET) from the fSET pin to signal ground. A 10μA current (IFREQ) flowing out of the fSET pin through RfSET develops a voltage on fSET. RfSET can be calculated as: RfSET (kΩ) = The relationship of fSET voltage to switching frequency is shown in Figure 3. For low output voltages from 0.8V to 1.5V, 400kHz operation is an optimal frequency for the best power conversion efficiency while maintaining the inductor current to about 30% to 40% of maximum load current. For output voltages from 1.8V to 3.0V, 500kHz to 600kHz is optimal. For output voltages from 3.0V to 5.0V, 750kHz operation is optimal, but due to the higher ripple current at 5V operation the output current is limited to 10A. The LTM4627 can be synchronized from 400kHz to 800kHz with an input clock that has a high level above 2V and a low level below 0.8V. The 400kHz low end operation limit is put in place to limit inductor ripple current. See the Typical Applications section for synchronization examples. The LTM4627 minimum on-time is limited to approximately 90ns. Guardband the on-time to 130ns. The on-time can be calculated as: t ON(MIN)= 1 ⎛ V OUT ⎞ •⎜ ⎟ FREQ ⎝ VIN ⎠ Output Voltage Tracking Output voltage tracking can be programmed externally using the TRACK/SS pin. The output can be tracked up and down with another regulator. The master regulator’s output is divided down with an external resistor divider that is the same as the slave regulator’s feedback divider to implement coincident tracking. The LTM4627 uses an accurate 60.4k resistor internally for the top feedback resistor. Figure 4 shows an example of coincident tracking. ⎛ 60.4k ⎞ VOUT(SLAVE) = ⎜ 1+ • V TRACK R TA ⎟⎠ ⎝ VTRACK is the track ramp applied to the slave’s track pin. VTRACK has a control range of 0V to 0.6V, or the internal reference voltage. When the master’s output is divided down with the same resistor values used to set the slave’s output, then the slave will coincident track with the master until it reaches its final value. The master will continue to FREQ(kHz) + 2kHz 4.5 4627f 12 LTM4627 APPLICATIONS INFORMATION 0.60 1 PHASE 2 PHASE 3 PHASE 4 PHASE 6 PHASE 0.55 0.50 RMS INPUT RIPPLE CURRENT DC LOAD CURRENT 0.45 0.40 0.35 0.30 0.25 0.20 0.15 0.10 0.05 0 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 0.5 0.55 0.6 0.65 0.7 0.75 0.8 0.85 0.9 DUTY FACTOR (VOUT/VIN) 4627 F02 Figure 2. Normalized Input RMS Ripple Current vs Duty Factor for One to Six μModule Regulators (Phases) 900 SWITCHING FREQUENCY (kHz) 800 700 600 500 400 300 200 100 0 0 0.5 1 1.5 fSET PIN VOLTAGE (V) 2 2.5 4627 F03 Figure 3. Relationship Between Switching Frequency and Voltage at the fSET Pin 4627f 13 LTM4627 APPLICATIONS INFORMATION its final value from the slave’s regulation point. Voltage tracking is disabled when VTRACK is more than 0.6V. RTA in Figure 4 will be equal to the RFB for coincident tracking. has a control range from 0V to 0.6V. The master’s TRACK/SS pin slew rate is directly equal to the master’s output slew rate in volts/time. The equation: The TRACK/SS pin of the master can be controlled by an external ramp or the soft-start function of that regulator can be used to develop that master ramp. The LTM4627 can be used as a master by setting the ramp rate on its track pin using a soft-start capacitor. A 1.2μA current source is used to charge the soft-start capacitor. The following equation can be used: MR • 60.4k = R TB SR where MR is the master’s output slew rate and SR is the slave’s output slew rate in volts/time. When coincident tracking is desired, then MR and SR are equal, thus RTB is equal to 60.4k. RTA is derived from equation: ⎛ C ⎞ t SOFT-START = 0.6 • ⎜ SS ⎟ ⎝ 1.2µA ⎠ R TA = Ratiometric tracking can be achieved by a few simple calculations and the slew rate value applied to the master’s TRACK/SS pin. As mentioned above, the TRACK/SS pin VIN 6V TO 16V C7 22μF 16V C9 22μF 16V C10 22μF 16V R2 10k SOFT-START CAPACITOR CSS 150pF where VFB is the feedback voltage reference of the regulator, and VTRACK is 0.6V. Since RTB is equal to the 60.4k VIN EXTVCC INTVCC PGOOD COMP VOUT TRACK/SS RUN R4 100k LTM4627 C3 22μF 16V C1 22μF 16V C2 22μF 16V R1 10k MASTER RAMP OR OUTPUT 150pF RTA 60.4k RTB 60.4k MODE_PLLIN VOSNS– COMP VOUT RUN + DIFF_OUT VOSNS+ MODE_PLLIN VOSNS– GND C11 100μF 6.3V 82pF VOUT_LCL fSET SGND C8 470μF 6.3V RFB1 40.2k EXTVCC INTVCC PGOOD LTM4627 VOUT2 1.5V AT 15A VFB VIN TRACK/SS R3 100k DIFF_OUT VOSNS+ GND + VOUT_LCL fSET SGND VIN 6V TO 16V 0.6V V V FB V + FB – TRACK 60.4k RFB R TB C4 470μF 6.3V C6 100μF 6.3V VOUT1 1.2V 15A 82pF VFB RFB 60.4k 4627 F04 Figure 4. Dual Outputs (1.5V and 1.2V) with Tracking 4627f 14 LTM4627 APPLICATIONS INFORMATION top feedback resistor of the slave regulator in equal slew rate or coincident tracking, then RTA is equal to RFB with VFB = VTRACK. Therefore RTB = 60.4k, and RTA = 60.4k in Figure 4. In ratiometric tracking, a different slew rate maybe desired for the slave regulator. RTB can be solved for when SR is slower than MR. Make sure that the slave supply slew rate is chosen to be fast enough so that the slave output voltage will reach its final value before the master output. For example, MR = 1.5V/ms, and SR = 1.2V/ms. Then RTB = 75k. Solve for RTA to equal 51.1k. For applications that do not require tracking or sequencing, simply tie the TRACK/SS pin to INTVCC to let RUN control the turn on/off. When the RUN pin is below its threshold or the VIN undervoltage lockout, then TRACK/SS is pulled low. MASTER OUTPUT OUTPUT VOLTAGE SLAVE OUTPUT electronic circuit breaker or fuse can be sized to be tripped or cleared when the bottom MOSFET is turned on to protect against the overvoltage. Foldback current limiting is disabled during soft-start or tracking start-up. Run Enable The RUN pin is used to enable the power module or sequence the power module. The threshold is 1.25V, and the pin has an internal 5.1V Zener to protect the pin. The RUN pin can be used as an undervoltage lockout (UVLO) function by connecting a resistor divider from the input supply to the RUN pin: VUVLO = ((R1+R2)/R2) • 1.25V. See the Block Diagram for the example of use. INTVCC Regulator The LTM4627 has an internal low dropout regulator from VIN called INTVCC. This regulator output has a 4.7μF ceramic capacitor internal. This regulator powers the internal controller and MOSFET drivers. The gate driver current is ~20mA for 750kHz operation. The regulator loss can be calculated as: (VIN – 5V) • 20mA = PLOSS TIME 4627 F05 Figure 5. Output Voltage Coincident Tracking Overcurrent and Overvoltage Protection The LTM4627 has overcurrent protection (OCP) in a short circuit. The internal current comparator threshold folds back during a short to reduce the output current. An overvoltage condition (OVP) above 10% of the regulated output voltage will force the top MOSFET off and the bottom MOSFET on until the condition is cleared. An input EXTVCC external voltage source ≥ 4.7V can be applied to this pin to eliminate the internal INTVCC LDO power loss and increase regulator efficiency. A 5V supply can be applied to run the internal circuitry and power MOSFET driver. If unused, leave pin floating. Stability Compensation The module has already been internally compensated for all output voltages. Table 4 is provided for most application requirements. The Linear Technology μModule Power Design Tool will be provided for other control loop optimization. 4627f 15 LTM4627 APPLICATIONS INFORMATION Thermal Considerations and Output Current Derating The thermal resistances reported in the Pin Configuration section of the data sheet are consistent with those parameters defined by JESD51-9 and are intended for use with finite element analysis (FEA) software modeling tools that leverage the outcome of thermal modeling, simulation, and correlation to hardware evaluation performed on a μModule package mounted to a hardware test board—also defined by JESD51-9 (“Test Boards for Area Array Surface Mount Package Thermal Measurements”). The motivation for providing these thermal coefficients in found in JESD 51-12 (“Guidelines for Reporting and Using Electronic Package Thermal Information”). Many designers may opt to use laboratory equipment and a test vehicle such as the demo board to anticipate the μModule regulator’s thermal performance in their application at various electrical and environmental operating conditions to compliment any FEA activities. Without FEA software, the thermal resistances reported in the Pin Configuration section are in-and-of themselves not relevant to providing guidance of thermal performance; instead, the derating curves provided in the data sheet can be used in a manner that yields insight and guidance pertaining to one’s application-usage, and can be adapted to correlate thermal performance to one’s own application. The Pin Configuration section typically gives four thermal coefficients explicitly defined in JESD 51-12; these coefficients are quoted or paraphrased below: 1 θJA, the thermal resistance from junction to ambient, is the natural convection junction-to-ambient air thermal resistance measured in a one cubic foot sealed enclosure. This environment is sometimes referred to as “still air” although natural convection causes the air to move. This value is determined with the part mounted to a JESD 51-9 defined test board, which does not reflect an actual application or viable operating condition. 2 θJCbottom, the thermal resistance from junction to the bottom of the product case, is the junction-to-board thermal resistance with all of the component power dissipation flowing through the bottom of the package. In the typical μModule, the bulk of the heat flows out the bottom of the package, but there is always heat flow out into the ambient environment. As a result, this thermal resistance value may be useful for comparing packages but the test conditions don’t generally match the user’s application. 3 θJCtop, the thermal resistance from junction to top of the product case, is determined with nearly all of the component power dissipation flowing through the top of the package. As the electrical connections of the typical μModule are on the bottom of the package, it is rare for an application to operate such that most of the heat flows from the junction to the top of the part. As in the case of θJCbottom, this value may be useful for comparing packages but the test conditions don’t generally match the user’s application. 4 θJB, the thermal resistance from junction to the printed circuit board, is the junction-to-board thermal resistance where almost all of the heat flows through the bottom of the μModule and into the board, and is really the sum of the θJCbottom and the thermal resistance of the bottom of the part through the solder joints and through a portion of the board. The board temperature is measured a specified distance from the package, using a two sided, two layer board. This board is described in JESD 51-9. A graphical representation of the aforementioned thermal resistances is given in Figure 6; blue resistances are contained within the μModule regulator, whereas green resistances are external to the μModule. As a practical matter, it should be clear to the reader that no individual or sub-group of the four thermal resistance parameters defined by JESD 51-12 or provided in the Pin Configuration section replicates or conveys normal operating conditions of a μModule. For example, in normal board-mounted applications, never does 100% of the device’s total power loss (heat) thermally conduct exclusively through the top or exclusively through bottom of the μModule—as the standard defines for θJCtop and θJCbottom, respectively. In practice, power loss is thermally dissipated in both directions away from the package—granted, in the absence of a heat sink and airflow, a majority of the heat flow is into the board. Within a SIP (system-in-package) module, be aware there are multiple power devices and components dissipating power, with a consequence that the thermal resistances 4627f 16 LTM4627 APPLICATIONS INFORMATION JUNCTION-TO-AMBIENT RESISTANCE (JESD 51-9 DEFINED BOARD) CASE (TOP)-TO-AMBIENT RESISTANCE JUNCTION-TO-CASE (TOP) RESISTANCE JUNCTION-TO-BOARD RESISTANCE JUNCTION JUNCTION-TO-CASE CASE (BOTTOM)-TO-BOARD (BOTTOM) RESISTANCE RESISTANCE At BOARD-TO-AMBIENT RESISTANCE 80421 F05 μMODULE DEVICE Figure 6. Graphical Representation of JESD 51-12 Thermal Coefficients relative to different junctions of components or die are not exactly linear with respect to total package power loss. To reconcile this complication without sacrificing modeling simplicity—but also, not ignoring practical realities—an approach has been taken using FEA software modeling along with laboratory testing in a controlled-environment chamber to reasonably define and correlate the thermal resistance values supplied in this data sheet: (1) Initially, FEA software is used to accurately build the mechanical geometry of the μModule and the specified PCB with all of the correct material coefficients along with accurate power loss source definitions; (2) this model simulates a software-defined JEDEC environment consistent with JSED51-9 to predict power loss heat flow and temperature readings at different interfaces that enable the calculation of the JEDEC-defined thermal resistance values; (3) the model and FEA software is used to evaluate the μModule with heat sink and airflow; (4) having solved for and analyzed these thermal resistance values and simulated various operating conditions in the software model, a thorough laboratory evaluation replicates the simulated conditions with thermocouples within a controlled-environment chamber while operating the device at the same power loss as that which was simulated. An outcome of this process and due-diligence yields a set of derating curves provided in other sections of this data sheet. After these laboratory test have been performed and correlated to the μModule model, then the θJB and θBA are summed together to correlate quite well with the μModule model with no airflow or heat sinking in a properly define chamber. This θJB + θBA value is shown in the Pin Configuration section and should accurately equal the θJA value because approximately 100% of power loss flows from the junction through the board into ambient with no airflow or top mounted heat sink. The 1.2V and 3.3V power loss curves in Figures 7 and 8 can be used in coordination with the load current derating curves in Figures 9 to 16 for calculating an approximate θJA thermal resistance for the LTM4627 with various heat sinking and airflow conditions. The power loss curves are taken at room temperature, and are increased with multiplicative factors according to the ambient temperature. These approximate factors are: 1 for 40°C; 1.05 for 50°C; 1.1 for 60°C; 1.15 for 70°C; 1.2 for 80°C; 1.25 for 90°C; 1.3 for 100°C; 1.35 for 110°C and 1.4 for 120°C. The derating curves are plotted with the output current starting at 15A and the ambient temperature at 40°C. The output voltages are 1.2V, and 3.3V. These are chosen to include the lower and higher output voltage ranges for correlating the thermal resistance. Thermal models are derived from several temperature measurements in a controlled temperature chamber along with thermal modeling analysis. The junction temperatures are monitored while ambient temperature is increased with and without airflow. The power loss increase with ambient temperature change is factored into the derating curves. The junctions are maintained at 120°C maximum while lowering output current or power with increasing ambient temperature. The decreased output current will decrease the inter4627f 17 LTM4627 APPLICATIONS INFORMATION nal module loss as ambient temperature is increased. The monitored junction temperature of 120°C minus the ambient operating temperature specifies how much module temperature rise can be allowed. As an example in Figure 11 the load current is derated to ~12A at ~80°C with no air or heat sink and the power loss for the 12V to 1.2V at 12A output is about 2.8W. The 2.8W loss is calculated with the ~2.35W room temperature loss from the 12V to 1.2V power loss curve at 12A, and the 1.2 multiplying factor at 80°C ambient. If the 80°C ambient temperature is subtracted from the 120°C junction temperature, then the difference of 40°C divided by 2.8W equals a 14°C/W θJA thermal resistance. Table 2 specifies a 13°C/W value which is very close. Table 2 and Table 3 provide equivalent 3.0 6 5VIN TO 1.2VOUT POWER LOSS 12VIN TO 1.2VOUT POWER LOSS 2.0 1.5 1.0 4 3 2 1 0.5 0 5VIN TO 3.3VOUT POWER LOSS 12VIN TO 3.3VOUT POWER LOSS 5 POWER LOSS (W) 2.5 POWER LOSS (W) thermal resistances for 1.2V and 3.3V outputs with and without airflow and heat sinking. The derived thermal resistances in Tables 2 and 3 for the various conditions can be multiplied by the calculated power loss as a function of ambient temperature to derive temperature rise above ambient, thus maximum junction temperature. Room temperature power loss can be derived from the efficiency curves in the Typical Performance Characteristics section and adjusted with the above ambient temperature multiplicative factors. The printed circuit board is a 1.6mm thick four layer board with two ounce copper for the two outer layers and one ounce copper for the two inner layers. The PCB dimensions are 95mm × 76mm. The BGA heat sinks are listed in Table 4. 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 OUTPUT CURRENT (A) 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 OUTPUT CURRENT (A) 4627 F08 4627 F07 Figure 8. 3.3VOUT Power Loss 16 16 14 14 12 12 OUTPUT CURRENT (A) OUTPUT CURRENT (A) Figure 7. 1.2VOUT Power Loss 10 8 6 4 0 LFM 200 LFM 400 LFM 2 0 10 8 6 4 0 40 50 60 70 0 LFM 200 LFM 400 LFM 2 80 90 100 110 120 130 40 50 60 70 80 90 100 110 120 130 AMBIENT TEMPERATURE (°C) AMBIENT TEMPERATURE (°C) 4627 F09 Figure 9. 5VIN to 1.2VOUT No Heat Sink 4627 F10 Figure 10. 5VIN to 1.2VOUT with Heat Sink 4627f 18 LTM4627 16 16 14 14 12 12 OUTPUT CURRENT (A) OUTPUT CURRENT (A) APPLICATIONS INFORMATION 10 8 6 4 10 8 6 4 0 LFM 200 LFM 400 LFM 2 0 40 50 60 70 0 LFM 200 LFM 400 LFM 2 80 0 90 100 110 120 130 40 50 60 70 80 90 100 110 120 130 AMBIENT TEMPERATURE (°C) AMBIENT TEMPERATURE (°C) 4627 F12 4627 F10 Figure 12. 12VIN to 1.2VOUT with Heat Sink 14 14 12 12 OUTPUT CURRENT (A) OUTPUT CURRENT (A) Figure 11. 12VIN to 1.2VOUT No Heat Sink 10 8 6 4 0 LFM 200 LFM 400 LFM 2 0 40 50 60 70 10 8 6 4 0 LFM 200 LFM 400 LFM 2 80 0 90 100 110 120 130 40 50 AMBIENT TEMPERATURE (°C) 60 70 80 90 100 110 120 130 AMBIENT TEMPERATURE (°C) 4627 F14 Figure 13. 5VIN to 3.3VOUT No Heat Sink Figure 14. 5VIN to 3.3VOUT with Heat Sink 16 16 14 14 12 12 OUTPUT CURRENT (A) OUTPUT CURRENT (A) 4627 F13 10 8 6 4 0 LFM 200 LFM 400 LFM 2 0 40 50 60 70 10 8 6 4 0 LFM 200 LFM 400 LFM 2 80 90 100 110 120 130 AMBIENT TEMPERATURE (°C) 0 40 50 60 70 80 90 100 110 120 130 AMBIENT TEMPERATURE (°C) 4627 F15 Figure 15. 12VIN to 3.3VOUT No Heat Sink 4627 F16 Figure 16. 12VIN to 3.3VOUT with Heat Sink 4627f 19 LTM4627 APPLICATIONS INFORMATION Table 2. 1.2V Output DERATING CURVE VIN POWER LOSS CURVE AIRFLOW (LFM) HEAT SINK θJA (°C/W) Figures 9, 11 5V, 12V Figure 7 0 None 13 Figures 9, 11 5V, 12V Figure 7 200 None 11 Figures 9, 11 5V, 12V Figure 7 400 None 8 Figures 10, 12 5V, 12V Figure 7 0 BGA Heat Sink 12 Figures 10, 12 5V, 12V Figure 7 200 BGA Heat Sink 8 Figures 10, 12 5V, 12V Figure 7 400 BGA Heat Sink 7 POWER LOSS CURVE AIRFLOW (LFM) HEAT SINK θJA (°C/W) Table 3. 3.3V Output DERATING CURVE VIN Figures 13, 15 5V, 12V Figure 8 0 None 13 Figures 13, 15 5V, 12V Figure 8 200 None 11 Figures 13, 15 5V, 12V Figure 8 400 None 8 Figures 14, 16 5V, 12V Figure 8 0 BGA Heat Sink 12 Figures 14, 16 5V, 12V Figure 8 200 BGA Heat Sink 8 Figures 14, 16 5V, 12V Figure 8 400 BGA Heat Sink 7 4627f 20 LTM4627 APPLICATIONS INFORMATION Table 4. Output Voltage Response vs Component Matrix (Refer to Figure 18) 0A to 7.5A Load Step VALUE PART NUMBER COUT1 AND COUT2 BULK VENDOR VALUE PART NUMBER CIN BULK VENDOR VALUE PART NUMBER TDK 22μF 6.3V C3216X7SOJ226M Sanyo POSCAP 1000μF 2.5V 2R5TPD1000M5 Sanyo 56μF 25V 25SVP56M Murata 22μF 16V GRM31CR61C226KE15L Sanyo POSCAP 470μF 2.5V 2R5TPD470M5 470μF 6.3V 6TPD470M COUT1 AND COUT2 CERAMIC VENDOR TDK 100μF 6.3V C4532X5ROJ107MZ Sanyo POSCAP Murata 100μF 6.3V GRM32ER60J107M Sanyo POSCAP VOUT CIN COUT1 (CERAMIC) AND CIN (V) (CERAMIC) (BULK)** COUT2 (CER AND BULK) CFF (pF) VIN (V) CCOMP (pF) PEAK TO PEAK DROOP DEVIATION (mV) (mV) RECOVERY TIME(μs) LOAD STEP (A/μs) RFB (kΩ) FREQ. (kHz) 1 22μF × 3 56μF 100μF × 2, 1000μF 68 150 5,12 50 100 30 7.5 90.9 400 1 22μF × 3 56μF 100μF × 2, 470μF × 2 82 150 5,12 50 100 20 7.5 90.9 400 1 22μF × 3 56μF 100μF × 4 82 33 5,12 52 108 18 7.5 90.9 400 1.2 22μF × 3 56μF 100μF × 2, 1000μF 82 150 5,12 40 80 20 7.5 60.4 400 1.2 22μF × 3 56μF 100μF, 470μF 82 150 5,12 60 120 20 7.5 60.4 400 1.2 22μF × 3 56μF 100μF × 2, 470μF × 2 82 150 5,12 40 80 25 7.5 60.4 400 1.2 22μF × 3 56μF 100μF × 4 82 33 5,12 50 114 20 7.5 60.4 400 1.5 22μF × 3 56μF 100μF × 2, 1000μF 82 150 5,12 60 120 23 7.5 40.2 400 1.5 22μF × 3 56μF 100μF, 470μF 82 47 5,12 67 130 20 7.5 40.2 400 1.5 22μF × 3 56μF 100μF × 2, 470μF × 2 82 150 5,12 60 120 25 7.5 40.2 400 1.5 22μF × 3 56μF 100μF × 3 82 33 5,12 65 130 20 7.5 40.2 400 1.8 22μF × 3 56μF 100μF × 2, 1000μF 68 150 5,12 64 130 25 7.5 30.1 400 1.8 22μF × 3 56μF 100μF, 470μF 82 150 5,12 76 135 22 7.5 30.1 400 1.8 22μF × 3 56μF 100μF × 2 82 none 5,12 66 132 20 7.5 30.1 400 2.5 22μF × 3 56μF 100μF × 2 82 none 5,12 88 164 30 7.5 19.1 500 2.5 22μF × 3 56μF 100μF, 470μF 82 150 5,12 100 200 25 7.5 19.1 500 3.3 22μF × 3 56μF 100μF × 2 82 none 5,12 100 200 30 7.5 13.3 600 3.3 22μF × 3 56μF 100μF, 470μF 82 150 5,12 100 200 30 7.5 13.3 600 5 22μF × 3 56μF 100μF × 2 68 none 12 125 250 20 7.5 8.25 700 5 22μF × 3 56μF 470μF 47 150 12 125 250 25 7.5 8.25 700 ** Bulk capacitance is optional if VIN has very low input impedance. HEAT SINK MANUFACTURER PART NUMBER WEBSITE Wakefield Engineering LTN20069 www.wakefield.com AAVID Thermalloy 375424B00034G www.aavidthermalloy.com 4627f 21 LTM4627 APPLICATIONS INFORMATION Safety Considerations The LTM4627 modules do not provide isolation from VIN to VOUT. There is no internal fuse. If required, a slow blow fuse with a rating twice the maximum input current needs to be provided to protect each unit from catastrophic failure. The device does support overvoltage protection and overcurrent protection. • Place a dedicated power ground layer underneath the unit. • To minimize the via conduction loss and reduce module thermal stress, use multiple vias for interconnection between top layer and other power layers. • Do not put vias directly on the pad, unless they are capped or plated over. Layout Checklist/Example • Place test points on signal pins for testing. The high integration of the LTM4627 makes the PCB board layout very simple and easy. However, to optimize its electrical and thermal performance, some layout considerations are still necessary. • Use a separated SGND ground copper area for components connected to signal pins. Connect the SGND to GND underneath the unit. • Use large PCB copper areas for high current paths, including VIN, GND and VOUT. It helps to minimize the PCB conduction loss and thermal stress. • For parallel modules, tie the COMP and VFB pins together. Use an internal layer to closely connect these pins together. Figure 17 gives a good example of the recommended layout. • Place high frequency ceramic input and output capacitors next to the VIN, GND and VOUT pins to minimize high frequency noise. VIN CIN CIN CONTROL CONTROL GND SIGNAL GROUND CONTROL COUT COUT VOUT VOUT 4627 F17 Figure 17. Recommended PCB Layout 4627f 22 LTM4627 TYPICAL APPLICATIONS VIN 4.5V TO 20V C3 22μF 25V C1 22μF 25V C2 22μF 25V CCOMP 150pF R1 10k C7 0.1μF VIN EXTVCC INTVCC PGOOD COMP VOUT TRACK/SS RUN R3 120k CONTINUOUS MODE LTM4627 DIFF_OUT fSET VOSNS+ MODE_PLLIN VOSNS– SGND GND + VOUT_LCL CFF 82pF COUT1 470μF 6.3V s2 COUT2* 100μF 6.3V VOUT 1.5V 15A VFB RFB 40.2k *SEE TABLE 4 4627 TA02 Figure 18. 4.5V to 20VIN, 1.5V at 15A Design 4627f 23 24 R1 200k C14 1μF OUT1 SET MOD LTC6908-1 OUT2 GND V+ INTVCC R2 10k VIN 7V TO 16V C9 22μF 16V C10 22μF 16V C13 0.1μF C1 22μF 16V C2 22μF 16V 100k SGND GND VOSNS– MODE_PLLIN VFB VOSNS+ DIFF_OUT fSET RUN LTM4627 VOUT_LCL VOUT TRACK/SS EXTVCC INTVCC PGOOD VFB VIN GND VOSNS– VOSNS+ DIFF_OUT VOUT_LCL COMP SGND MODE_PLLIN fSET RUN LTM4627 VOUT EXTVCC INTVCC PGOOD TRACK/SS 270pF 100k VIN COMP INTVCC Figure 19. 1V at 30A, Two Parallel Outputs with 2-Phase Operation CLOCK SYNC 180 PHASE C3 22μF 16V CLOCK SYNC 0 PHASE C7 22μF 16V INTVCC 4627 TA03 + RFB1 45.3k 150pF C4 470μF 6.3V + C6 100μF 6.3V C8 470μF 6.3V C11 100μF 6.3V 1V AT 30A LTM4627 TYPICAL APPLICATIONS 4627f LTM4627 TYPICAL APPLICATIONS VIN 7V TO 16V R1 10k C20 22μF 16V VIN EXTVCC INTVCC PGOOD VOUT COMP TRACK/SS RUN MODE_PLLIN VOSNS– SGND V C2 1μF R2 100k GND + DIFF_OUT VOSNS+ INTVCC + LTM4627 VOUT_LCL fSET 100k 4-PHASE CLOCK VOUT 1.2V AT 60A INTVCC C22 22μF 16V C28 0.1μF C21 470μF 6.3V C24 100μF 6.3V 270pF VFB RFB2 15k 150pF SET LTC6902 MOD DIV PH OUT1 OUT2 GND OUT4 C14 22μF 16V C18 22μF 16V VIN EXTVCC INTVCC PGOOD VOUT COMP TRACK/SS OUT3 RUN VOSNS+ MODE_PLLIN VOSNS– SGND C9 22μF 16V GND + DIFF_OUT fSET 100k C7 22μF 16V LTM4627 VOUT_LCL C15 470μF 6.3V C18 100μF 6.3V INTVCC VFB VIN EXTVCC INTVCC PGOOD VOUT COMP TRACK/SS RUN LTM4627 DIFF_OUT fSET VOSNS+ MODE_PLLIN VOSNS– 100k SGND GND + VOUT_LCL C8 470μF 6.3V C11 100μF 6.3V INTVCC VFB 150pF C3 22μF 16V C1 22μF 16V VIN EXTVCC INTVCC PGOOD VOUT COMP TRACK/SS RUN LTM4627 DIFF_OUT fSET VOSNS+ MODE_PLLIN VOSNS– 100k SGND GND + VOUT_LCL C4 470μF 6.3V C6 100μF 6.3V INTVCC VFB 4627 TA04 Figure 20. 1.2V, 60A, Current Sharing with 4-Phase Operation 4627f 25 LTM4627 PACKAGE DESCRIPTION Pin Assignment Table (Arranged by Pin Number) A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 PIN NAME VIN VIN VIN VIN VIN VIN INTVCC MODE_PLLIN TRACK/SS RUN COMP MTP1 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 PIN NAME VIN VIN VIN VIN VIN VIN GND GND MTP2 fSET PIN NAME C1 VIN C2 VIN C3 VIN C4 VIN C5 VIN C6 VIN C7 GND C8 C9 GND C10 MTP3 C11 MTP4 C12 MTP5 PIN NAME D1 GND D2 GND D3 GND D4 GND D5 GND D6 GND D7 D8 GND D9 INTVCC D10 MTP6 D11 MTP7 D12 MTP8 PIN NAME E1 GND E2 GND E3 GND E4 GND E5 GND E6 GND E7 GND E8 E9 GND E10 E11 E12 EXTVCC PIN NAME F1 GND F2 GND F3 GND F4 GND F5 GND F6 GND F7 GND F8 GND F9 GND F10 F11 PGOOD F12 VFB G1 G2 G3 G4 G5 G6 G7 G8 G9 G10 G11 G12 PIN NAME GND GND GND GND GND GND GND GND GND SGND PGOOD H1 H2 H3 H4 H5 H6 H7 H8 H9 H10 H11 H12 PIN NAME GND GND GND GND GND GND GND GND GND SGND SGND PIN NAME J1 VOUT J2 VOUT J3 VOUT J4 VOUT J5 VOUT J6 VOUT J7 VOUT J8 VOUT J9 VOUT J10 VOUT J11 J12 VOSNS+ PIN NAME K1 VOUT K2 VOUT K3 VOUT K4 VOUT K5 VOUT K6 VOUT K7 VOUT K8 VOUT K9 VOUT K10 VOUT K11 VOUT K12 DIFF_OUT PIN NAME L1 VOUT L2 VOUT L3 VOUT L4 VOUT L5 VOUT L6 VOUT L7 VOUT L8 VOUT L9 VOUT L10 VOUT L11 VOUT L12 VOUT_LCL PIN NAME M1 VOUT M2 VOUT M3 VOUT M4 VOUT M5 VOUT M6 VOUT M7 VOUT M8 VOUT M9 VOUT M10 VOUT M11 VOUT M12 VOSNS– PACKAGE PHOTO 4627f 26 Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 6.9850 5.7150 4.4450 3.1750 1.9050 0.6350 0.0000 0.6350 1.9050 3.1750 4.4450 5.7150 6.9850 3.1750 0.630 SUGGESTED PCB LAYOUT TOP VIEW 1.9050 PACKAGE TOP VIEW 0.6350 0.0000 0.6350 4 1.9050 PAD 1 CORNER 15 BSC 3.1750 aaa Z 6.9850 5.7150 4.4450 4.4450 5.7150 6.9850 15 BSC Y 0.630 X bbb Z DETAIL B 4.22 – 4.42 DETAILS OF PAD #1 IDENTIFIER ARE OPTIONAL, BUT MUST BE LOCATED WITHIN THE ZONE INDICATED. THE PAD #1 IDENTIFIER MAY BE EITHER A MOLD OR MARKED FEATURE LAND DESIGNATION PER JESD MO-222, SPP-010 SYMBOL TOLERANCE 0.15 aaa bbb 0.10 eee 0.05 6. THE TOTAL NUMBER OF PADS: 133 5. PRIMARY DATUM -Z- IS SEATING PLANE 4 3 2. ALL DIMENSIONS ARE IN MILLIMETERS 3 M L TRAY PIN 1 BEVEL COMPONENT PIN “A1” PADS SEE NOTES 1.27 BSC 13.97 BSC 0.12 – 0.28 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994 DETAIL A 0.27 – 0.37 SUBSTRATE eee S X Y DETAIL B 0.630 ±0.025 SQ. 133x aaa Z 3.95 – 4.05 MOLD CAP Z (Reference LTC DWG # 05-08-1777 Rev Ø) LGA Package 133-Lead (15mm × 15mm × 4.32mm) K G F E LTMXXXXXX μModule PACKAGE BOTTOM VIEW H D C B LGA 133 1008 REV Ø A DETAIL A PACKAGE IN TRAY LOADING ORIENTATION J 13.97 BSC 1 2 3 4 5 6 7 8 9 10 11 12 C(0.30) PAD 1 LTM4627 PACKAGE DESCRIPTION 4627f 27 LTM4627 TYPICAL APPLICATION 3.3V at 10A Design 5V C3 22μF 16V C1 22μF 16V C2 22μF 16V C7 0.1μF R1 10k VIN EXTVCC INTVCC PGOOD COMP VOUT TRACK/SS RUN R3 174k CONTINUOUS MODE LTM4627 DIFF_OUT fSET VOSNS+ MODE_PLLIN VOSNS– SGND GND C4 100μF X5R VOUT_LCL 82pF C6 100μF X5R 6.3V VOUT 3.3V 10A 5V VFB RFB 13.3k C5 47pF 4627 TA05 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LTM4600 10A DC/DC μModule Regulator Basic 10A DC/DC μModule LTM4601A 12A DC/DC μModule Regulator with PLL, Output Tracking/ Margining and Remote Sensing Synchronizable, PolyPhase Operation to 48A, Pin Compatible with the LTM4627 LTM4602 6A DC/DC μModule Regulator Pin Compatible with the LTM4600 LTM4603 6A DC/DC μModule Regulator with PLL and Output Tracking/Margining and Remote Sensing Synchronizable, PolyPhase Operation, LTM4603-1 Version Has No Remote Sensing, Pin Compatible with the LTM4601 LTM4604A 4A Low Voltage DC/DC μModule Regulator 2.375V ≤ VIN ≤ 5.5V; 0.8V ≤ VOUT ≤ 5V, 9mm × 15mm × 2.3mm (Ultrathin) LGA Package LTM4605 Buck-Boost DC/DC μModule Family All Pin Compatible; Up to 5A; Up to 36VIN, 34VOUT 15mm × 15mm × 2.8mm LTM4606 Ultralow Noise 6A DC/DC μModule Regulator 4.5V ≤ VIN ≤ 28V, 0.6V ≤ VOUT ≤ 5V, 15mm × 15mm × 2.8mm Package LTM4607 Buck-Boost DC/DC μModule Family All Pin Compatible; Up to 5A; Up to 36VIN, 34VOUT 15mm × 15mm × 2.8mm LTM4608A 8A Low Voltage DC/DC μModule Regulator 2.7V ≤ VIN ≤ 5.5V; 0.6V ≤ VOUT ≤ 5V; 9mm × 15mm × 2.8mm LGA Package LTM4609 Buck-Boost DC/DC μModule Family All Pin Compatible; Up to 5A; Up to 36VIN, 34VOUT 15mm × 15mm × 2.8mm LTM4612 Ultralow Noise High VOUT DC/DC μModule Regulator 5A, 5V ≤ VIN ≤ 36V, 3.3V ≤ VOUT ≤ 15V, 15mm × 15mm × 2.8mm Package LTM8023 36V, 2A DC/DC μModule Regulator 3.6V ≤ VIN ≤ 36V, 0.8V ≤ VOUT ≤ 10V, 9mm × 11.75mm × 2.8mm Package LTM8032 Ultralow Noise 36V, 2A DC/DC μModule Regulator EN55022 Class B Compliant; 0.8V ≤ VOUT ≤ 10V; 3.6V ≤ VIN ≤ 36V; 9mm × 15mm × 2.8mm 4627f 28 Linear Technology Corporation LT 0810 • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com © LINEAR TECHNOLOGY CORPORATION 2010