ONSEMI NCV8460

NCV8460
Self Protected High Side
Driver with Temperature
Shutdown and Current Limit
The NCV8460 is a fully protected High−Side driver that can be used
to switch a wide variety of loads, such as bulbs, solenoids and other
acuators. The device is internally protected from an overload
condition by an active current limit and thermal shutdown.
A diagnostic output reports ON and OFF state open load conditions
as well as thermal shutdown.
•
MARKING
DIAGRAM
8
SO−8
D SUFFIX
CASE 751
8
Features
•
•
•
•
•
•
•
•
•
•
•
http://onsemi.com
Short Circuit Protection
Thermal Shutdown with Automatic Restart
CMOS (3.3 V / 5 V) compatible control input
Open Load Detection in On and Off State
Diagnostic Output
Undervoltage and Overvoltage Shutdown
Loss of Ground Protection
ESD protection
Slew Rate Control for Low EMI Switching
Very Low Standby Current
NCV Prefix for Automotive and Other Applications Requiring
AEC−Q100 Qualified Site and Change Controls
These are Pb−Free Devices
1
1
V8460
A
L
Y
W
G
V8460
ALYW
G
= Specific Device Code
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
PIN CONNECTIONS
GND 1
8
VD
IN 2
7
OUT
STAT 3
6
OUT
5
VD
NC
4
(Top View)
Typical Applications
• Switch a Variety of Resistive, Inductive and Capacitive Loads
• Can Replace Electromechanical Relays and Discrete Circuits
• Automotive / Industrial
ORDERING INFORMATION
Device
Package
Shipping†
NCV8460DR2G
SOIC−8
(Pb−Free)
1000 / Tape & Reel
†For information on tape and reel specifications,
including part orientation and tape sizes, please
refer to our Tape and Reel Packaging Specifications
Brochure, BRD8011/D.
© Semiconductor Components Industries, LLC, 2011
April, 2011 − Rev. 0
1
Publication Order Number:
NCV8460/D
NCV8460
VD
Overvoltage
Detection
Undervoltage
Detection
Regulated
Chargepump
Output
Clamping
Input
Buffer
IN
Pre
Driver
Control
Logic
Current
Limitation
STAT
Overtemperature
Detection
On−State
Open Load Detection
GND
Off−State
Open Load Detection
Figure 1. Block Diagram
PIN DESCRIPTION
Pin #
Symbol
Description
1
GND
2
IN
3
STAT
Status Output
4
N/C
No Connection
5
VD
Supply Voltage
6
OUT
Output
7
OUT
Output
8
VD
Ground
Logic Level Input
Supply Voltage
http://onsemi.com
2
í
OUT
NCV8460
MAXIMUM RATINGS
Value
Rating
DC Supply Voltage
Peak Transient Input Voltage
(Load Dump 51.5 V, VD = 13.5 V, ISO7637−2 pulse 5)
Symbol
Min
Max
Unit
VD
−16
42
V
65
V
Vpeak
Input Voltage
Vin
−8
8
V
Iin
−5
5
mA
Iout
−6
Internally
Limited
A
Negative Ground Current
−Ignd
−200
−
mA
Status Current
Istatus
−5
5
mA
Input Current
Output Current (Note
2)
Power Dissipation Tc = 25°C
Ptot
Electrostatic Discharge
(HBM Model 100 pF / 1500 W)
Input
Status
Output
VD
1.183
W
DC
Single Pulse Inductive Load Switching Energy (Note 1)
(L = 1.8 mH, Vbat = 13.5 V; IL = 9 A, TJstart = 150°C
Operating Junction Temperature
Storage Temperature
4
3.5
5
5
kV
kV
kV
kV
EAS
100
mJ
TJ
−40
+150
°C
Tstorage
−55
+150
°C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. Not subjected to production testing
2. Reverse Output current has to be limited by the load to stay within absolute maximum ratings and thermal performance.
THERMAL RESISTANCE RATINGS
Parameter
Thermal Resistance
Junction−to−Lead
Junction−to−Ambient (min. Pad)
Junction−to−Ambient (1” square pad size, FR−4, 1 oz Cu)
http://onsemi.com
3
Symbol
Max Value
Unit
RqJL
RqJA
RqJA
72
110.8
105.6
°C/W
°C/W
°C/W
NCV8460
ELECTRICAL CHARACTERISTICS (8 ≤ VD ≤ 36 V; −40°C < TJ < 150°C unless otherwise specified)
Value
Rating
Symbol
Conditions
Min
Typ
Max
Unit
Operating Supply
Voltage
VD
6
−
36
V
Undervoltage Shutdown
VUV
3
4
5.5
V
6
V
Undervoltage
VUV_Rst
Overvoltage Shutdown
VOV
36
On Resistance
RON
Iout = 2 A; TJ = 25°C, VD > 6 V
Iout = 2 A, VD > 6 V
Standby Current
ID
Off State, Vin = Vout = 0 V, VD = 13.5 V
On State; Vin = 5 V, VD = 13.5 V, Iout = 0 A
Output Leakage Current
IL
Vin = Vout = 0 V
Vin = 0 V, Vout = 3.5 V
Vin = Vout = 0 V, VD = 13.5 V
V
10
1.5
−20
60
120
mW
20
3.5
mA
mA
50
10
3
mA
1.25
V
INPUT CHARACTERISTICS
Input Voltage − Low
Vin_low
Input Current − Low
Iin_low
Input Voltage − High
Vin_high
Input Current − High
Iin_high
Input Hysteresis Voltage
Vhyst
Input Clamp Voltage
Vin_cl
Vin = 1.25 V
1
mA
3.25
V
Vin = 3.25 V
10
0.25
Iin = 1 mA
Iin = −1 mA
11
−13
mA
V
12
−12
13
−11
V
SWITCHING CHARACTERISTICS
Turn−On Delay Time
td_on
to 10% Vout, VD = 13.5 V, RL = 6.5 W
40
ms
Turn−Off Delay Time
td_off
to 90% Vout, VD = 13.5 V, RL = 6.5 W
30
ms
Slew Rate On
dVout / dton
10% to 80% Vout, VD = 13.5 V, RL = 6.5 W
0.9
V / ms
Slew Rate Off
dVout / dtoff
90% to 10% Vout, VD = 13.5 V, RL = 6.5 W
0.7
V / ms
OUTPUT DIODE CHARACTERISTICS (Note 3)
Forward Voltage
VF
Iout = −1.3 A, TJ = 150°C
0.6
V
STATUS PIN CHARACTERISTICS
Status Output Voltage
Low
Status Leakage Current
Status Pin Input
Capacitance
Status Clamp Voltage
Vstat_low
Istat = 1.6 mA
0.2
0.5
V
Istat_leakage
Vstat = 5 V
1
10
mA
Cstat
Vstat = 5 V (Note 3)
100
pF
Vstat_cl
Istat =1 mA
Istat = −1 mA
10
−2.2
11
−1.2
12
−0.6
V
200
°C
PROTECTION FUNCTIONS (Note 4)
Temperature Shutdown
(Note 3)
TSD
150
175
Temperature Shutdown
Hysteresis (Note 3)
TSD_hyst
7
15
8 V < VD < 36 V
6
9
6 V < VD < 36 V
5
Output Current Limit
Status Delay in Overload
Ilim
td_stat
°C
15
A
15
A
20
ms
3. Not subjected to production testing
4. To ensure long term reliability under heavy overload or short circuit conditions, protection and related diagnostic signals must be used
together with a proper hardware/software strategy. If the devices operates under abnormal conditions this hardware/software solutions
must limit the duration and number of activation cycles.
http://onsemi.com
4
NCV8460
ELECTRICAL CHARACTERISTICS (8 ≤ VD ≤ 36 V; −40°C < TJ < 150°C unless otherwise specified)
Value
Rating
Symbol
Conditions
Min
Typ
Max
Unit
Iout = 2 A, Vin = 0 V, L = 6 mH
VD −
41
VD −
45
VD −
55
V
30
300
mA
200
ms
3.5
V
1000
ms
PROTECTION FUNCTIONS (Note 4)
Switch Off Output Clamp
Voltage
Vclamp
DIAGNOSTICS CHARACTERISTICS
Openload On State
Detection Threshold
IOL
Vin = 5 V
Openload On State
Detection Delay
td_OL_on
Iout = 0 A
Openload Off State
Detection Threshold
VOL
Vin = 0 V
Openload Detection
Delay at Turn Off
td_OL_off
1.5
−
3. Not subjected to production testing
4. To ensure long term reliability under heavy overload or short circuit conditions, protection and related diagnostic signals must be used
together with a proper hardware/software strategy. If the devices operates under abnormal conditions this hardware/software solutions
must limit the duration and number of activation cycles.
Iout < IOL
VIN
TJ > TJ_TSD
VIN
Vout > VOL
VSTAT
VSTAT
Td_STAT
Td_OL_off
Td_OL_on
Td_STAT
Figure 2. Open Load Status Timing
(with external pull−up)
Figure 3. Overtemperature Status Timing
Vout
90%
80%
dVout / dt(on)
dVout / dt(off)
10%
t
td(on)
td(off)
Vin
t
Figure 4. Switching Timing Diagram
http://onsemi.com
5
NCV8460
STATUS PIN TRUTH TABLE
Input
Output
Status
Normal Operation
Conditions
L
H
L
H
H
H
Undervoltage
L
H
L
L
X
X
Overvoltage
L
H
L
L
H
H
Current Limitation
L
H
H
L
X
X
H
(TJ < TSD) H
(TJ > TSD) L
Overtemperature
L
H
L
L
H
L
Output Voltage > VOL
L
H
H
H
L
H
Output Current < IOL
L
H
L
H
H
L
http://onsemi.com
6
NCV8460
TYPICAL CHARACTERISTICS CURVES
5
45
4.9
44
4.8
43
4.6
VOV (V)
VUV (V)
4.7
4.5
4.4
4.3
41
40
39
4.2
38
4.1
4
−50
0
50
100
37
150
−50
Figure 6. Overvoltage Shutdown vs.
Temperature
128
120
150°C
108
68
10
15
20
25
150°C
60
25°C
−40°C
20
−40°C
5
80
40
25°C
48
30
35
0
40
0
VD (V)
10
Figure 7. RDS(on) vs. VD
4
100
3.5
IL (mA)
VIN HIGH (V)
150°C
80
60
25°C
20
10
20
30
VD (V)
40
50
3
2.5
2
1.5
−40°C
0
20
Figure 8. OFF State Standby Current vs. VD
120
40
150
100
88
0
100
Figure 5. Undervoltage Shutdown vs.
Temperature
140
0
50
TEMPERATURE (°C)
148
28
0
TEMPERATURE (°C)
Ioff (mA)
RDS(on) (mW)
42
30
1
−50
40
0
50
100
150
VD (V)
TEMPERATURE (°C)
Figure 9. Output Leakage vs. VD
Vout = 0 V
Figure 10. Vin Threshold High vs. Temperature
http://onsemi.com
7
NCV8460
TYPICAL CHARACTERISTICS CURVES
10
4
9
8
2.5
6
5
3
1.5
0
50
100
1
−50
150
0
50
100
150
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 11. Vin Threshold Low vs. Temperature
Figure 12. Input Current vs. Temperature
−10
13.5
−10.5
13
−11
Vin_cl (neg) (V)
14
Vin_cl (pos) (V)
Iin @ 1.25 V
2
1
−50
12.5
12
11.5
−11.5
−12
−12.5
−13
11
−13.5
10.5
−14
10
−50
0
50
100
150
−50
0
50
Figure 13. Input Clamp Voltage (Positive) vs.
Temperature
Figure 14. Input Clamp Voltage (Negative) vs.
Temperature
90
80
80
25°C
70
−40°C
60
60
Toff (ms)
−40°C
50
150°C
40
30
20
20
10
10
10
20
VD (V)
30
0
40
25°C
50
30
0
150
TEMPERATURE (°C)
90
40
100
TEMPERATURE (°C)
70
Ton (ms)
Iin @ 3.25 V
4
2
0
Iin @ 5 V
7
3
Iin (mA)
Vin LOW (V)
3.5
150°C
0
Figure 15. Turn On Time vs. VD
5
10
15
20
VD (V)
25
30
Figure 16. Turn Off Time vs. VD
http://onsemi.com
8
35
40
NCV8460
TYPICAL CHARACTERISTICS CURVES
1.6
0.70
1.4
25°C
1.2
0.50
dVout / dt(off) (mS)
dVout / dt(on) (mS)
0.60
0.40
0.30
−40°C
150°C
0.20
0.8
0.6
−40°C
150°C
0.2
0
5
10
15
20
25
30
35
40
0
5
20
25
30
Figure 18. Slew Rate OFF vs. VD
35
40
300
150°C
250
Vstat_low (mV)
0.75
0.7
0.65
0.6
0.55
0.5
200
25°C
150
−40°C
100
50
0.45
0
50
TEMPERATURE (°C)
100
150
0
0
10
Figure 19. Forward Voltage (@ −1.3 A) vs.
Temperature
20
VD (V)
30
40
Figure 20. STAT Low Voltage vs. VD
5
13
4.5
12.5
4
3.5
12
3
V(pos) (V)
Istat_Leakage (mA)
15
Figure 17. Slew Rate ON vs. VD
0.8
2.5
2
11.5
11
1.5
1
10.5
0.5
0
−50
10
VD (V)
0.85
0.4
−50
0
VD (V)
0.9
VF (V)
25°C
0.4
0.10
0
1.0
0
50
TEMPERATURE (°C)
100
150
Figure 21. Status Leakage Current vs.
Temperature
10
−50
0
50
100
TEMPERATURE (°C)
150
Figure 22. Status Clamp Voltage (Positive) vs.
Temperature
http://onsemi.com
9
NCV8460
TYPICAL CHARACTERISTICS CURVES
14
0
12
−1
11
Ilim (A)
STATUS CLAMP (neg) (V)
13
−2
10
9
8
−3
7
6
−4
−50
0
50
100
5
−50
150
50
100
TEMPERATURE (°C)
Figure 23. Status Clamp Voltage (Negative) vs.
Temperature
Figure 24. Current Limit vs. Temperature
VD = 13.5 V
150
300
48
47.5
−40°C
250
47
25°C
46.5
200
150°C
46
IOL (mA)
Vclamp (V)
0
TEMPERATURE (°C)
45.5
45
150
100
44.5
44
50
43.5
43
0
10
20
30
40
0
−50 −30 −10 10
50
30
50
70
90 110 130 150
VD (V)
TEMPERATURE (°C)
Figure 25. Turn Off Output Clamp Voltage vs.
VD and Temperature
Figure 26. ON State Open Load Detection vs.
Temperature VD = 13.5 V
100
2.9
2.7
−40°C
25°C
ILmax (A)
Vol (V)
2.5
2.3
2.1
10
25°C
150°C
150°C
1.9
1.7
1.5
0
5
10
15
20
25
30
35
40
1
10
100
VD (V)
L (mH)
Figure 27. Off State OL Detection Threshold
vs. VD and Temperature
Figure 28. Single−Pulse Maximum Switch−off
Current vs. Load Inductance
http://onsemi.com
10
NCV8460
TYPICAL CHARACTERISTICS CURVES
1000
25°C
Emax (mJ)
150°C
100
10
10
100
L (mH)
Figure 29. Single−Pulse Maximum Switch−off
Current vs. Load Inductance
ISO 7637−2: 2004(E) PULSE TEST RESULTS
ISO 7637−2:2004(E)
Test Levels
Delays and
Test Pulse
I
II
III
IV
Impedance
1
g
g
−75 V
−100 V
2 ms, 10 W
2a
g
g
+37 V
+50 V
0.05 ms, 10 W
3a
g
g
−112 V
−150 V
0.1 ms, 50 W
3b
g
g
+75 V
+100 V
0.1 ms, 50 W
4
g
g
−6 V
−7 V
5 s, .01 W
5 (Load Dump)
g
g
+65 V
+87 V
400 ms, 2 W
ISO 7637−2:2004(E)
Test Results
Test Pulse
Class
III
IV
1
I
II
C
C
2a
C
C
3a
C
C
3b
C
C
4
A
A
5 (Load Dump)
C
E
Functional Status
A
All functions of a device perform as designed during and after exposure to disturbance.
B
All functions of a device perform as designed during exposure. However,one or more of
them can go beyond specified tolerance. All functions return automatically to within normal
limits after exposure is removed. Memory functions shall remain class A.
C
One or more functions of a device do not perform as designed during exposure but return
automatically to normal operation after exposure is removed.
D
One or more functions of a device do not perform as designed during exposure and do not return to normal operation until
exposure is removed and the device is reset by simple
E
One or more functions of a device do not perform as designed during and after exposure and cannot be returned to proper
operation without replacing the device.
http://onsemi.com
11
NCV8460
Normal Operation
Input
Load Voltage
Status
Undervoltage
VUV_HYS
VD
VUV
Input
Load Voltage
Status
Undefined
Overvoltage
VD > VOV
VD < VOV
VCC
Input
Load Voltage
Status
Open Load with External pull−up
Input
Load Voltage
Status
VOL
Open Load without External pull−up
Input
Load Voltage
Status
Overtemperature
TJ
TR
Input
Load Voltage
Status
Figure 30. Waveforms
http://onsemi.com
12
TTSD
NCV8460
+
5V
−
VD
STAT
Vout
Input
GND
Reverse Battery
Protection
Load
DGND
RGND
Figure 31. Application Diagram
Reverse Battery Protection
This offset will be increased when more than one device
shares the resistor.
Power Dissipation during a reverse battery event is equal
to:
An external resistor RGND is required to adequately
protect the device from a Reverse Battery event. The resistor
value can be calculated using the following two formulas.
1. RGND ≥ 600 mV / (Id (on) max)
2. RGND ≥ (-VD) / (-Ignd)
Maximum (-Ignd) current, which is the reverse GND pin
current, can be found in the Maximum Ratings section.
Several High Side Devices can share same the reverse
battery protection resistor. Please note that the sum of (Id
(on) max) of all devices should be used to calculate RGND
value. If the microprocessor ground is not common with the
device ground, RGND will produce a voltage offset ((Id (on)
max) x RGND) with respect to the IN and STAT pins.
2
P D + ǒ* V DǓ ń R GND
In the case of high power dissipation due to several
devices sharing RGND, it is recommended to place a diode
DGND in the ground path as an alternate reverse battery
protection method. When driving an inductive load, a 1 kW
resistor should be placed in parallel with the DGND diode.
This method will also produce a voltage offset of ~600 mV
with respect to the IN and STAT pins. This diode can also be
shared amongst several High Side Devices. This voltage
offset will vary if DGND is shared by multiple devices.
http://onsemi.com
13
NCV8460
Vbat
5V
V pull −up
VD
STAT
OL
R pull
−up
I
V OUT
Input
GND
RL
Figure 32. Open Load Detection In Off State
OFF State Open Load Detection
when the load is connected, the Rpull-up must also not cause
the OFF State OL to miss detecting an OL condition when
the load is disconnected. A VOUT voltage below the
VOL_max (Openload Off State Detection Threshold)
maximum value with the load (RL) disconnected needs to be
avoided. The following formula shows this relationship:
Off State Open Load Detection requires an external
pull-up resistor (Rpull-up) connected between VOUT pin and
a positive supply voltage (Vpull-up).
The external Rpull-up resistor value should be selected to
ensure that a false OFF State OL condition is not detected
when the load (RL) is connected. A VOUT voltage above the
VOL_min (Openload Off State Detection Threshold)
minimum value with the load (RL) connected needs to be
avoided. The following formula shows this relationship:
ǒ
R pull*up t ǒV pull*up * V OL_maxǓńOL 1
OL 1 + I LǒOutput Leakage with V OUT + 3.5 VǓ
Because Id (OFF) may significantly increase if VOUT is
pulled high (up to several mA), Rpull-up resistor should be
connected to a supply that is switched OFF when the module
is in standby.
Ǔ
V OUT + V pull*upńǒR L ) R pull*upǓ R L t V OL_min
In addition to ensuring the selected Rpull-up resistor value
does not cause a false OFF State OL detection condition
http://onsemi.com
14
NCV8460
1000
R(t), (°C/W)
100
10
1
Duty Cycle = 0.5
0.2
0.1
0.05
0.02
0.01
0.1
Single Pulse
0.00001
0.0001
0.001
0.01
0.1
PULSE TIME (s)
1
Figure 33. Transient Thermal Impedance
180
160
140
qJA (°C/W)
0.01
0.000001
1.0 oz
120
2.0 oz
100
80
60
0
200
400
600
COPPER HEAT SPREADER AREA
800
(mm2)
Figure 34. RqJA vs Copper Area
http://onsemi.com
15
1000
10
100
100
NCV8460
PACKAGE DIMENSIONS
SOIC−8 NB
CASE 751−07
ISSUE AK
−X−
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
6. 751−01 THRU 751−06 ARE OBSOLETE. NEW
STANDARD IS 751−07.
A
8
5
S
B
0.25 (0.010)
M
Y
M
1
4
−Y−
K
G
C
N
DIM
A
B
C
D
G
H
J
K
M
N
S
X 45 _
SEATING
PLANE
−Z−
0.10 (0.004)
H
D
0.25 (0.010)
M
Z Y
S
X
M
J
SOLDERING FOOTPRINT*
S
MILLIMETERS
MIN
MAX
4.80
5.00
3.80
4.00
1.35
1.75
0.33
0.51
1.27 BSC
0.10
0.25
0.19
0.25
0.40
1.27
0_
8_
0.25
0.50
5.80
6.20
INCHES
MIN
MAX
0.189
0.197
0.150
0.157
0.053
0.069
0.013
0.020
0.050 BSC
0.004
0.010
0.007
0.010
0.016
0.050
0 _
8 _
0.010
0.020
0.228
0.244
1.52
0.060
7.0
0.275
4.0
0.155
0.6
0.024
1.270
0.050
SCALE 6:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
16
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCV8460/D