Typical Size 6.4 mm X 9.7 mm SN65HVS880 www.ti.com .......................................................................................................................................................... SLAS592B – MARCH 2008 – REVISED JUNE 2008 24 V, EIGHT-CHANNEL DIGITAL-INPUT SERIALIZER FEATURES 1 • Eight Sensor Inputs – High Input Voltage up to 30 V – Selectable Debounce Filters From 0 ms to 3 ms – Adjustable Current Limits From 0.2 mA to 5.2 mA – Field Inputs and Supply Lines Protected to 15-kV HBM • Output Drivers for External Status LEDs • Cascadable for More Inputs in Multiples of Eight 2 • • • SPI-Compatible Interface Regulated 5-V Output for External Digital Isolator Over-Temperature and Low-Supply Voltage Indicator APPLICATIONS • • • Sensor Inputs for Industrial Automation and Process Control – IEC61131-2 Type 1, 2, or 3 Switches – EN60947-5-2 Proximity Switches High Channel Count Digital Input Modules for PC and PLC Systems Decentralized I/O Modules DESCRIPTION The SN65HVS880 is a 24-V, eight-channel, digital-input serializer for high-channel density digital input modules of PC and PLC based systems in industrial automation. In combination with galvanic isolators the device completes the interface between the 24-V sensor outputs of the field-side and the low-voltage controller inputs at the control-side. Input signals provided by EN60947-5-2 compliant 2- and 3-wire proximity switches are current-limited and then validated by internal debounce filters. The input switching characteristic is in accordance with IEC61131-2 for Type 1, 2, and 3 sensor switches. Upon the application of load and clock signals, input data is latched in parallel into the shift register and afterwards clocked out serially via a subsequent isolator into a serial PLC input. Cascading of multiple SN65HVS880 is possible by connecting the serial output of the leading device with the serial input of the following device, enabling the design of high-channel count input modules. Input status is indicated via 3-mA constant current LED outputs. An external precision resistor is required to set the internal reference current. The integrated voltage regulator provides a 5-V output to supply low-power isolators. An on-chip temperature sensor together with an internal supply voltage monitor provides a chip-okay (CHOK) indication. The SN65HVS880 comes in a 28-pin PWP PowerPAD™ package allowing for efficient heat dissipation. The device is specified for operation at temperatures from –40°C to 85°C. 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PowerPAD is a trademark of Texas Instruments. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2008, Texas Instruments Incorporated SN65HVS880 SLAS592B – MARCH 2008 – REVISED JUNE 2008 .......................................................................................................................................................... www.ti.com Voltage Regulator 24 V In Debounce Select DB0:DB1 Serial Input 5V 8 8 8 SERIALIZER LED Outputs RE0:RE7 2 Signal Conditioning Field Inputs IP0:IP7 5 V Out IREF Adj: RLIM Field Ground 3 Control Inputs LD, CE, CLK Serial Output DB0 DB1 IP0 RE0 IP1 RE1 IP2 RE2 IP3 RE3 IP4 RE4 RLIM V24 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15 FGND SIP LD CLK CE SOP IP7 RE7 IP6 RE6 IP5 RE5 CHOK 5VOP FUNCTIONAL BLOCK DIAGRAM Voltage Regulator V24 5VOP 5V Thermal Protection & Supply Monitor CHOK FGND RE0 IP0 SIP Voltage Sense IP7 DB1 Current Sense & RE7 DB0 Debounce Select Adj. Current Thresholds Debounce Filter LD CE Channel 0 SERIALZER RLIM CLK Channel 7 SOP 2 Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): SN65HVS880 SN65HVS880 www.ti.com .......................................................................................................................................................... SLAS592B – MARCH 2008 – REVISED JUNE 2008 TERMINAL FUNCTIONS TERMINAL PIN NO. NAME DESCRIPTION 1, 2 DB0, DB1 3, 5, 7, 9, 11, 18, 20, 22 Debounce select inputs IPx Input channel x 4, 6, 8, 10, 12, 17, 19, 21 REx Return path x (LED drive) 13 RLIM Current limiting resistor 14 V24 15 5VOP 24 VDC field supply 5 V output to supply low-power isolators 16 CHOK Chip okay indicator output 23 SOP Serial data output 24 CE Clock enable input 25 CLK Serial clock input 26 LD Load pulse input 27 SIP Serial data input 28 FGND Field ground Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): SN65HVS880 3 SN65HVS880 SLAS592B – MARCH 2008 – REVISED JUNE 2008 .......................................................................................................................................................... www.ti.com ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range (unless otherwise noted) MIN MAX V24 Field power input V24 –0.3 35 V VIPx Field digital inputs IPx –0.3 35 V VID Voltage at any logic input DB0, DB1, CLK, SIP, CE, LD –0.5 6 V IO Output current CHOK, SOP ±8 mA All pins ±4 IPx,V24 ±15 Human-Body Model (1) VESD Electrostatic discharge PTOT Continuous total power dissipation TJ Junction temperature (1) (2) (3) UNIT kV Charged-Device Model (2) All pins ±1 kV Machine Model (3) All pins ±100 V 170 °C MAX UNIT See Thermal Characteristics table JEDEC Standard 22, Method A114-A. JEDEC Standard 22, Method C101 JEDEC Standard 22, Method A115-A THERMAL CHARACTERISTICS PARAMETER θJA Junction-to-air thermal resistance θJB Junction-to-board thermal resistance θJC Junction-to-case thermal resistance PD Device power dissipation TEST CONDITIONS MIN TYP High-K thermal resistance ILOAD = 50 mA, RIN = 0, IPO–IP7 = V24 = 30 V, RE7 = FGND, fCLK = 100 MHz, IIP-LIM and ICC = worst case with RLIM = 25 kΩ 35 °C/W 15 °C/W 4.27 °C/W 2591 mW RECOMMENDED OPERATING CONDITIONS V24 Field supply voltage VIPL Field input low-state input voltage (1) MIN TYP MAX 18 24 30 V 6 V 0 (1) UNIT VIPH Field input high-state input voltage 10 30 V VIL Logic low-state input voltage 0 0.8 V VIH Logic high-state input voltage 2 5.5 V RLIM Current limiter resistor 500 kΩ fIP Input data rate (2) 17 0 TJ TA (1) (2) 4 –40 25 1 Mbps 150 °C 85 °C Field input voltages correspond to an input resistor of RIN = 1.2 kΩ Maximum data rate corresponds to 0 ms debounce time, (DB0 = open, DB1 = FGND), and RIN = 0 Ω Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): SN65HVS880 SN65HVS880 www.ti.com .......................................................................................................................................................... SLAS592B – MARCH 2008 – REVISED JUNE 2008 ELECTRICAL CHARACTERISTICS all voltages measured against FGND unless otherwise stated, see Figure 12 SYMBOL PARAMETER TERMINAL VTH–(IP) Low-level device input threshold voltage VTH+(IP) High-level device input threshold voltage VHYS(IP) Device input hysteresis VTH–(IN) Low-level field input threshold voltage VTH+(IN) High-level field input threshold voltage VHYS(IN) Field input hysteresis VTH–(V24) Low-level V24-monitor threshold voltage VTH+(V24) High-level V24-monitor threshold voltage IP0–IP7 TEST CONDITIONS MIN TYP 4 4.3 18 V< V24 < 30 V, RIN = 0 Ω 5.2 measured at field side of RIN 18 V < V24 < 30 V, RIN = 1.2 kΩ ± 5%, RLIM = 25 kΩ V24 16.8 IP0–IP7 Input current limit VOL Logic low-level output voltage VOH Logic high-level output voltage IIL Logic input leakage current IRE-on RE on-state current ICC(V24) Supply current VO(5V) ILIM(5V) SOP, CHOK V 18 V24 Linear regulator output voltage 5VOP V 1.4 1.83 2.3 kΩ 10 V < VIPx < 30 V, RLIM = 25 kΩ 3.15 3.6 4 mA IOL = 20 µA 0.4 IOH = –20 µA 4 RLIM = 25 kΩ, REX = FGND 2.8 3.15 IP0 to IP7 = V24, 5VOP = open, REX = FGND, All logic inputs open 50 µA 3.5 mA 8.7 mA 18 V < V24 < 30 V, no load 4.5 5 5.5 18 V < V24 < 30 V, IL = 50 mA 4.5 5 5.5 V 115 5VOP, V24 tDB Debounce times of input channels IP0–IP7 tDB-HL Voltage monitor debounce time after V24 < 15 V (CHOK turns low) V V –50 Linear regulator output current limit ΔV5/ΔV24 Line regulation V 3 V < VIPx < 6 V, RIN = 1.2 kΩ ± 5%, RLIM = 25 kΩ DB0, DB1, SIP, LD, CE, CLK RE0–RE7 V V 16.05 0.75 Input resistance IIP-LIM V 10 1 15 V V 8.4 9.4 UNIT V 5.5 0.9 6 VHYS(V24) V24-monitor hysteresis RIP MAX 18 V < V24 < 30 V, IL = 5 mA mA 2 DB0 = open, DB1 = FGND 0 DB0 = FGND, DB1 = open 1 DB0 = DB1 = open 3 mV/V ms 1 ms 6 ms V24, CHOK tDB-LH Voltage monitor debounce time after V24 > 18 V (CHOK turns high) TOVER Over-temperature indication 150 °C TSHDN Shutdown temperature 170 °C Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): SN65HVS880 5 SN65HVS880 SLAS592B – MARCH 2008 – REVISED JUNE 2008 .......................................................................................................................................................... www.ti.com TIMING REQUIREMENTS over operating free-air temperature range (unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNIT tW1 CLK pulse width See Figure 6 4 ns tW2 LD pulse width See Figure 4 6 ns tSU1 SIP to CLK setup time See Figure 7 4 ns tH1 SIP to CLK hold time See Figure 7 2 ns tSU2 Falling edge to rising edge (CE to CLK) setup time See Figure 8 4 ns tREC LD to CLK recovery time See Figure 5 2 fCLK Clock pulse frequency See Figure 6 DC ns 100 MHz SWITCHING CHARACTERISTICS over operating free-air temperature range (unless otherwise noted) SYMBOL PARAMETER TEST CONDITIONS MIN TYP MAX UNIT tPLH1, tPHL1 CLK to SOP CL = 15 pF, see Figure 6 10 ns tPLH2, tPHL2 LD to SOP CL = 15 pF, see Figure 4 14 ns tr, tf Rise and fall times CL = 15 pF, see Figure 6 5 ns 6 Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): SN65HVS880 SN65HVS880 www.ti.com .......................................................................................................................................................... SLAS592B – MARCH 2008 – REVISED JUNE 2008 INPUT CHARACTERISTICS 30 RIN = 1.2 kΩ 25 a) IIP-LIM = 2.5 mA ( RLIM = 36.1 kΩ) b) IIP-LIM = 3.0 mA ( RLIM = 30.1 kΩ) VIN (V) a) b) c) c) IIP-LIM = 3.6 mA ( RLIM = 24.9 kΩ) 20 15 10 Off On 5 Field Input Thresholds 0 0 . 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 IIN (mA) Figure 1. Typical Input Characteristics 9.6 101.5 V24 = 24 V VIN = 24 V 9.4 101.0 RIN = 1.2 kΩ 9.2 RLIM = 24.9 kΩ 9.0 100.5 VIN (V) IIP-LIM/IIP-LIM–25ºC(%) 102.0 100.0 8.8 VTH+(IN) V24 = 24 V RIN = 1.2 kΩ RLIM = 24.9 kΩ 8.6 99.5 8.4 99.0 VTH–(IN) 8.2 98.5 98.0 –45 –35 –25 –15 –5 5 15 25 35 45 55 65 75 85 95 8.0 –45 –35 –25 –15 –5 5 15 25 35 45 55 65 75 85 95 TA (ºC) TA (ºC) Figure 2. Typical Current Limiter Variation vs Ambient Temperature Figure 3. Typical Limiter Threshold Voltage Variation vs Ambient Temperature Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): SN65HVS880 7 SN65HVS880 SLAS592B – MARCH 2008 – REVISED JUNE 2008 .......................................................................................................................................................... www.ti.com PARAMETER MEASUREMENT INFORMATION Waveforms For the complete serial interface timing, refer to Figure 21. tw2 LD LD t REC t PLH2 tPHL2 CLK SOP Figure 4. Parallel – Load Mode Figure 5. Serial – Shift Mode valid 1/fCLK t w1 SIP CLK tSU 1 tPLH1 tH1 tPHL1 CLK SOP tr tf Figure 6. Serial – Shift Mode Figure 7. Serial – Shift Mode CLK t SU2 CE CLK inhibited Figure 8. Serial – Shift Clock Inhibit Mode 8 Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): SN65HVS880 SN65HVS880 www.ti.com .......................................................................................................................................................... SLAS592B – MARCH 2008 – REVISED JUNE 2008 VOLTAGE REGULATOR PERFORMANCE CHARACTERISTICS 5.000 4 ILOAD = 5 mA 4.995 2 TA = 27°C 4.990 ILOAD = 0 mA 4.985 0 VOUT (V) ΔVOUT (mV) 6 –2 –4 4.980 4.975 –6 4.970 –8 4.965 4.960 –45 –35 –25 –15 –5 –10 0 5 10 15 20 25 30 35 5 15 25 35 45 55 65 75 85 95 TA (°C) VIN (V) Figure 9. Line Regulation Figure 10. Output Voltage vs Ambient Temperature 5.5 5.0 4.5 RLOAD = 100 Ω VOUT (V) 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 0 5 10 15 20 VIN (V) 25 30 35 Figure 11. Output Voltage vs Input Voltage RIN IPx IIN VTH(IN) VTH(IP) SN65HVS880 FGND Figure 12. On/Off Threshold Voltage Measurements Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): SN65HVS880 9 SN65HVS880 SLAS592B – MARCH 2008 – REVISED JUNE 2008 .......................................................................................................................................................... www.ti.com DEVICE INFORMATION Digital Inputs V-REF 5V ILIM Mirror n = 72 IIN IPx ILIM Limiter IINmax = ILIM IREF RLIM Figure 13. Digital Input Stage Each digital input operates as a controlled current sink limiting the input current to a maximum value of ILIM. The current limit is derived from the reference current via ILIM = n × IREF, and IREF is determined by IREF = VREF/RLIM. Thus, changing the current limit requires the change of RLIM to a different value via: RLIM = n × VREF/ILIM. While the device is specified for a current limit of 3.6 mA, (via RLIM = 25 kΩ), it is easy to lower the current limit to further reduce the power consumption. For example, for a current limit of 2.5 mA simply calculate: RLIM = 90 90 = = 36 kΩ ILIM 2.5 mA Debounce Filter The HVS880 applies a simple analog/digital filtering technique to remove unintended signal transitions due to contact bounce or other mechanical effects. Any new input (either low or high) must be present for the duration of the selected debounce time to be latched into the shift register as a valid state. The logic signal levels at the control inputs, DB0 and DB1 of the internal Debounce-Select logic determine the different debounce times listed in the following truth table. Table 1. Debounce Times DB1 10 DB0 FUNCTION Open Open 3 ms delay Open FGND 1 ms delay FGND Open 0 ms delay (Filter bypassed) FGND FGND Reserved Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): SN65HVS880 SN65HVS880 www.ti.com .......................................................................................................................................................... SLAS592B – MARCH 2008 – REVISED JUNE 2008 5V IPx REF REx RLIM FGND Figure 14. Equivalent Input Diagram Shift Register The conversion from parallel input to serial output data is performed by an eight-channel, parallel-in serial-out shift register. Parallel-in access is provided by the internal inputs, PIP0–PIP7, that are enabled by a low level at the load input (LD). When clocked, the latched input data shift towards the serial output (SOP). The shift register also provides a clock-enable function. Clocking is accomplished by a low-to-high transition of the clock (CLK) input while LD is held high and the clock enable (CE) input is held low. Parallel loading is inhibited when LD is held high. The parallel inputs to the register are enabled while LD is low independently of the levels of the CLK, CE, or serial (SIP) inputs. SIP D CLK CE Logic Q CP R D Q CP S R D Q CP S R D Q CP S R D Q CP S R D Q CP S R D Q CP S R D Q SOP CP S R S LD PIP 0 PIP 1 PIP 2 PIP 3 PIP 4 PIP 5 PIP 6 PIP 7 Figure 15. Shift Register Logic Structure Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): SN65HVS880 11 SN65HVS880 SLAS592B – MARCH 2008 – REVISED JUNE 2008 .......................................................................................................................................................... www.ti.com Table 2. Function Table INPUTS (1) FUNCTION LD CLK CE L X X Parallel load H X H No change H ↑ L Shift (1) Shift = content of each internal register shifts towards serial outputs. Data at SIP is shifted into first register. Voltage Regulator The on-chip linear voltage regulator provides a 5 V supply to the internal- and external circuitry, such as digital isolators, with an output drive capability of 50 mA and a typical current limit of 115 mA. The regulator accepts input voltages from 30 V down to 10 V. Because the regulator output is intended to supply external digital isolator circuits proper output voltage decoupling is required. For best results connect a 1 µF and a 0.1 µF ceramic capacitor as close as possible to the 5VOP-output. For longer traces between the SN65HVS880 and isolators of the ISO72xx family use additional 0.1 µF and 10 pF capacitors next to the isolator supply pins. Make sure, however, that the total load capacitance does not exceed 4.7 µF. For good stability the voltage regulator requires a minimum load current, IL-MIN. Ensure that under any operating condition the ratio of the minimum load current in mA to the total load capacitance in µF is larger than 1: IL-MIN 1 mA > 1 µF CL Supply Voltage Monitor The integrated supply voltage monitor senses the supply voltage of the SN65HVS880 at the V24-pin. If this voltage drops below 15 V but stays within the regulator’s operating range, i.e., 15 V > V24 > 10 V, the output CHOK goes low 1 ms later. When the supply voltage returns to 24 V, the CHOK output turns logic high after 6 ms. Should the supply voltage drop below 10 V, the device ceases operation. Upon the supply returning to above 18 V, the CHOK output turns high again after 6 ms. 18 V 18 V 15 V 15 V V24 15 V > V24 > 10 V 1 ms debounce time starts 10 V 1 ms debounce time starts tDB-HL tDB-LH V24 < 10 V Circuit ceases operation tDB-LH CHOK Figure 16. CHOK Output Timing as a Function of Supply Voltage Drop at V24 Temperature Sensor An on-chip temperature sensor monitors the device temperature and signals a fault condition if the device becomes too hot. A first trip point exists at 150°C. If the junction temperature exceeds this trip point, the sensor output, being active low, presents a low to the input of the AND gate forcing the CHOK output to go low. If the junction temperature continues to rise, passing a second trip point at 170°C, all device outputs assume tri-state. 12 Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): SN65HVS880 SN65HVS880 www.ti.com .......................................................................................................................................................... SLAS592B – MARCH 2008 – REVISED JUNE 2008 Chip Okay (CHOK) Output The CHOK output is the Boolean AND-function of the two, active-low fault conditions: temperature failure and supply failure. As such CHOK is a device health indicator, assuming logic high in the absence of any fault condition. If either one of the two or both fault conditions occur, CHOK becomes logic low. A special condition occurs, however, when the chip temperature exceeds the second temperature trip point due to an output short. Then the CHOK output buffer becomes tri-state, thus separating the buffer from the external circuitry. An internal 100 kΩ pulldown resistor, connecting the CHOK-pin to ground, is used as a “cooling down” resistor, which continues to provide a logic low level to the external circuitry. Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): SN65HVS880 13 SN65HVS880 SLAS592B – MARCH 2008 – REVISED JUNE 2008 .......................................................................................................................................................... www.ti.com APPLICATION INFORMATION System-Level EMC The SN65HVS880 must operate reliably in harsh industrial environments. At a system level, the device is tested according to several international electromagnetic compatibility (EMC) standards. In addition to the device internal ESD structures, external protection circuitry, such as the one in Figure 17, is needed to absorb as much energy from burst- and surge-transients as possible. R1 VSUP = 24 V R1 56-Ω, 1/3-W MELF resistor D1 33–36-V fast Zener diode, ZSMB36 C1 10-μF, 60-V ceramic capacitor RIN 1.2-kΩ, 1/4-W MELF resistor V24 CS C1 D1 DS SN65HVS880 FE FGND 0V RIN IP0–IP7 IPx CIN 22-nF, 60-V ceramic capacitor CS 4.7-nF, 2-kV polypropylene capacitor DS 39-V transient voltage suppressor, SM15T39CA D2 Super rectifier: BYM10-1000 or General purpose rectifier: 1N4007 CIN FGND 0V CS D2 FE Figure 17. Typical EMC Protection Circuitry for Supply and Signal Inputs Input Channel Switching Characteristics The input stage of the HVS880 is so designed, that for an input resistor RIN = 1.2 kΩ the trip point for signalling an ON-condition is at 9.4 V at 3.6 mA. This trip point satisfies the switching requirements of IEC61131-2 Type 1 and Type 3 switches. Type 2 Type 1 30 30 25 VIN (V) ON 20 30 15 10 5 25 ON 20 VIN (V) 25 VIN (V) Type 3 15 10 5 OFF 0 –30 5 10 IIN (mA) 10 5 OFF 0 –3 15 ON 20 15 0 5 10 15 OFF 0 –3 20 25 IIN (mA) 30 0 5 10 IIN (mA) 15 Figure 18. Switching Characteristics for IEC61131-2 Type 1, 2, and 3 Proximity Switches For a Type 2 switch application, two inputs are connected in parallel. The current limiters then add to a total maximum current of 7.2 mA. While the return-path (RE-pin), of one input might be used to drive an indicator LED, the RE-pin of the other input channel should be connected to ground (FGND). Paralleling input channels reduces the number of available input channels from an octal Type 1 or Type 3 input to a quad Type 2 input device. Note, that in this configuration output data of an input channel is represented by two shift register bits. 14 Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): SN65HVS880 SN65HVS880 www.ti.com .......................................................................................................................................................... SLAS592B – MARCH 2008 – REVISED JUNE 2008 RIN RIN IP0 IP0 CIN CIN RE0 RE0 RIN RIN IP1 IP1 CIN CIN RE1 RE1 Figure 19. Paralleling Two Type 1 or Type 3 Inputs Into One Type 2 Input Digital Interface Timing The digital interface of the SN65HVS880 is SPI compatible and interfaces, isolated or non-isolated, to a wide variety of standard micro controllers. SN65HVS880 IP0 IP7 SERIALIZER SIP HOST CONTROLLER ISO7241 LD OUTA INA CE OUTB INB CLK OUTC INC SOP IND OUTD LOAD STE SCLK SOMI Figure 20. Simple Isolation of the Shift Register Interface Upon a low-level at the load input, LD, the information of the field inputs, IP0 to IP7 is latched into the shift register. Taking /LD high again blocks the parallel inputs of the shift register from the field inputs. A low-level at the clock-enable input, CE, enables the clock signal, CLK, to serially shift the data to the serial output, SOP. Data is clocked at the rising edge of CLK. Thus after eight consecutive clock cycles all field input data have been clocked out of the shift register and the information of the serial input, SIP, appears at the serial output, SOP. Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): SN65HVS880 15 SN65HVS880 SLAS592B – MARCH 2008 – REVISED JUNE 2008 .......................................................................................................................................................... www.ti.com CLK CE SIP high LD PIP0–PIP6 PIP7 IP 6 IP7 SOP don’t care IP 5 IP4 inhibit IP3 IP2 IP1 IP 0 SIP Serial shift Figure 21. Interface Timing for Parallel-Load and Serial-Shift Operation of the Shift Register Cascading for High Channel Count Input Modules Designing high-channel count modules require cascading multiple SN65HVS880 devices. Simply connect the serial output (SOP) of a leading device with the serial input (SIP) of a following device without changing the processor interface. HOST CONTROLLER ISO7241 4 X SN65HVS880 OUTA INA LOAD OUTB INB STE OUTC INC CLK SCLK SOMI SOP OUTD IP7 SERIALIZER IP0 IP7 IP0 SERIALIZER CE LD SIP SOP CE CLK LD SIP SOP CLK IP7 SERIALIZER IP0 IP7 IP0 SERIALIZER CE LD SIP CLK SOP LD CE SIP IND Figure 22. Cascading Four SN65HVS880 for a 32-Channel Input Module 16 Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): SN65HVS880 SN65HVS880 www.ti.com .......................................................................................................................................................... SLAS592B – MARCH 2008 – REVISED JUNE 2008 Typical Digital Input Module Application (Logic) SM15T39CA 24V1 24 V 5V 5V-ISO SM15T39A (Sensors) 24V2 Isolated DC/DC 4.7 nF 2 kV 4.7 nF 2 kV GND2 0V Power Supply 4.7 nF 2 kV FE GND1 0V-ISO 56 Ω MELF Srew Terminals Z2SMB36 10 µF 60 V 1N4007 1 µF 0.1 µF SN65HVS880 1.2 kΩ MELF 22 nF S0 V24 5VOP IP0 CHOK RE0 1.2 kΩ MELF VCC1 HOST CONTROLLER SIP EN2 EN1 VCC LD OUTA INA LOAD CLK OUTB INB SCLK CE INC OUTC INT RE7 SOP IND OUTD SOMI RLIM DB0 GND2 GND1 DGND FGND DB1 IP7 22 nF S7 ISO7241 VCC2 24.9 kΩ Figure 23. Typical Digital Input Module Application Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): SN65HVS880 17 PACKAGE OPTION ADDENDUM www.ti.com 11-Jul-2008 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty SN65HVS880PWP ACTIVE HTSSOP PWP 28 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR SN65HVS880PWPG4 ACTIVE HTSSOP PWP 28 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR SN65HVS880PWPR ACTIVE HTSSOP PWP 28 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR SN65HVS880PWPRG4 ACTIVE HTSSOP PWP 28 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 20-Jun-2008 TAPE AND REEL INFORMATION *All dimensions are nominal Device SN65HVS880PWPR Package Package Pins Type Drawing SPQ HTSSOP 2000 PWP 28 Reel Reel Diameter Width (mm) W1 (mm) 330.0 16.4 Pack Materials-Page 1 A0 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 6.9 10.2 1.8 12.0 16.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 20-Jun-2008 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN65HVS880PWPR HTSSOP PWP 28 2000 346.0 346.0 33.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DSP Clocks and Timers Interface Logic Power Mgmt Microcontrollers RFID RF/IF and ZigBee® Solutions amplifier.ti.com dataconverter.ti.com dsp.ti.com www.ti.com/clocks interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/lprf Applications Audio Automotive Broadband Digital Control Medical Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/medical www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2008, Texas Instruments Incorporated