REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Added device type 05. Added case outlines M, N, 4, 5, 6, 7, and 8. Added vendor cage code 88379. 96-08-30 K. A. Cottongim B Figure 1; For case outlines 5, 6, 7 and 8 changed dimension D3 min and max from 1.030 and 1.040 inches to 1.020 and 1.060 inches. Changed dimension A min from .156 inches to .135 inches. Changed dimension L min from .145 inches to .132 inches. -sld 98-06-25 K.A. Cottongim C Added case outline 9. Figure 1; changed case outline M to be either a single or dual cavity package. Figure 1; changed the dimension A2 max limit from .015 inches to .025 inches for case outline M. Added thermal resistance ratings for all case outlines to paragraph 1.3 . Added vendor cage 88379 for case outline M, device types 01 through 05. Table I; changed IOL from 12.0 mA to 8.0 mA for the VOL test. -sld 00-06-20 Raymond Monnin REV SHEET REV C C C C C C C C C C C C C C C C C C C SHEET 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 REV STATUS REV C C C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Steve L. Duncan STANDARD MICROCIRCUIT DRAWING CHECKED BY Michael C. Jones THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE APPROVED BY Kendall A. Cottongim AMSC N/A DRAWING APPROVAL DATE 94-12-16 REVISION LEVEL C DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216 MICROCIRCUIT, HYBRID, DIGITAL, FLASH ERASABLE/PROGRAMMABLE READ ONLY MEMORY, 128K x 32-BIT SIZE CAGE CODE A 67268 SHEET DSCC FORM 2233 APR 97 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. 1 OF 5962-94716 33 5962-E148-00 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes, class D (lowest reliability), class E, (exceptions), class G (lowered high reliability), class H (high reliability), and class K, (highest reliability) and a choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 Federal stock class designator \ 94716 RHA designator (see 1.2.1) 01 Device type (see 1.2.2) / H Device class designator (see 1.2.3) M Case outline (see 1.2.4) X Lead finish (see 1.2.5) \/ Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type 01 02 03 04 05 Generic number WF128K32-150HQ5, ACT-F128K32N-150 WF128K32-120HQ5, ACT-F128K32N-120 WF128K32-90HQ5, ACT-F128K32N-090 WF128K32-70HQ5, ACT-F128K32N-070 WF128K32-60HQ5, ACT-F128K32N-060 Circuit function EPROM, FLASH, 128K x 32-bit EPROM, FLASH, 128K x 32-bit EPROM, FLASH, 128K x 32-bit EPROM, FLASH, 128K x 32-bit EPROM ,FLASH, 128K x 32-bit Access time 150 ns 120 ns 90 ns 70 ns 60 ns 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level as follows: Device class D, E, G, H, or K Device performance documentation Certification and qualification to MIL-PRF-38534 STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL C SHEET 2 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator M N S T U V W X Y Z 4 5 6 7 8 9 See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 Terminals 68 68 66 66 66 66 66 66 66 66 66 66 66 66 66 68 Package style Co-fired ceramic, single/dual cavity, quad flatpack, lead formed Co-fired ceramic, single cavity, quad flatpack, lead formed Hex-in-line, single cavity, with standoffs Hex-in-line, single cacvity, without standoffs Hex-in-line, single cavity, with standoffs Hex-in-line, single cavity, without standoffs Hex-in-line, single cavity, with standoffs Hex-in-line, single cavity, without standoffs Hex-in-line, single cavity, with standoffs Hex-in-line, single cavity, without standoffs Ceramic, single cavity, quad flat pack 1.075", hex-in-line, single cavity, with standoffs 1.075", hex-in-line, single cavity, with standoffs 1.075", hex-in-line, single cavity, with standoffs 1.075", hex-in-line, single cavity, with standoffs Co-fired ceramic, single cavity, ultra low profile, quad flatpack 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ 1/ 2/ Supply voltage range (VCC) 2/ ....................................................... -2.0 V dc to +7.0 V dc Signal voltage range (any pin except A9 ) 2/ ................................ Power dissipation (PD).................................................................... -2.0 V dc to +7.0 V dc 1.1 W Thermal resistance, junction-to-case (θJC): Case outline M ............................................................................ Case outline N ............................................................................ Case outline 4 ............................................................................. Case outline 9 ............................................................................. Case outlines 5, 6, 7, and 8........................................................ Case outlines S, T, U, V, W, X, Y, and Z ................................... Storage temperature range ............................................................ Lead temperature (soldering, 10 seconds).................................... Data retention ................................................................................. Endurance (write/erase cycles) ...................................................... A9 voltage for sector protect (VID) 3/............................................. 11.3°C/W 9°C/W 4.07°C/W 4.57°C/W 13.13°C/W 10.63°C/W -65°C to +150°C +300°C 10 years minimum 10,000 cycles minimum -2.0 V dc to +14.0 V dc Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Minimum DC voltage on input or I/O pins is -0.5 V dc. During voltage transitions, input may overshoot V to -2.0 V dc for SS periods of up to 20 ns. Maximum DC voltage on output and I/O pins is V CC may overshoot to V CC 3/ + 0.5 V dc. During voltage transitions, outputs + 2.0 V dc for periods of up to 20 ns. Minimum DC input voltage on A9 pin is -0.5 V dc. During voltage transitions, A9 may overshoot V SS to -2.0 V dc for periods of up to 20 ns. Maximum DC input voltage on A9 is +13.5 V dc which may overshoot to +14.0 V dc for periods of up to 20 ns. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL C SHEET 3 1.4 Recommended operating conditions. Supply voltage range (VCC) ............................................................ +4.5 V dc to +5.5 V dc Input low voltage range (VIL) .......................................................... -0.5 V dc to +0.8 V dc Input high voltage range (VIH) ........................................................ +2.0 V dc to VCC + 0.3 V dc Case operating temperature range (TC)......................................... -55°C to +125°C A9 voltage for sector protect (VID).................................................. +11.5 V dc to +12.5 V dc 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solitation. SPECIFICATION DEPARTMENT OF DEFENSE MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. STANDARDS DEPARTMENT OF DEFENSE MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Microcircuit Case Outlines. HANDBOOKS DEPARTMENT OF DEFENSE MIL-HDBK-103 - List of Standard Microcircuit Drawings (SMD's). MIL-HDBK-780 - Standard Microcircuit Drawings. (Unless otherwise indicated, copies of the specification, standards, and handbook are available from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as designated in the device manufacturer's Quality Management (QM) plan or as designated for the applicable device class. Therefore, the tests and inspections herein may not be performed for the applicable device class (see MIL-PRF-38534). Furthermore, the manufacturer may take exceptions or use alternate methods to the tests and inspections herein and not perform them. However, the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL C SHEET 4 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Truth table(s). The truth table(s) shall be as specified on figure 3. 3.2.4 Timing diagram(s). The timing diagram(s) shall be as specified on figures 4, 5, and 6 . 3.2.5 Block diagram. The block diagram shall be as specified on figure 7. 3.2.6 Output load circuit. The output load circuit shall be as specified on figure 8. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Programming procedure. The programming procedure shall be as specified by the manufacturer and shall be available upon request. 3.6 Marking of Device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's vendor similar PIN may also be marked. 3.7 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DSCC-VA) upon request. 3.8 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DSCC-VA shall affirm that the manufacturer's product meets the performance requirements of MIL-PRF-38534 and herein. 3.9 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 3.10 Endurance. A reprogrammability test shall be completed as part of the vendor's reliability monitors. This reprogrammability test shall be done for the initial characterization and after any design process changes which may affect the reprogrammability of the device. The methods and procedures may be vendor specific, but shall guarantee the number of program/erase cycles listed in section 1.3 herein over the full military temperature range. The vendor's procedure shall be kept under document control and shall be made available upon request of the acquiring or preparing activity. 3.11 Data retention. A data retention stress test shall be completed as part of the vendor's reliability monitors. This test shall be done for initial characterization and after any design process change which may affect data retention. The methods and procedures may be vendor specific, but shall guarantee the number of years listed in section 1.3 herein over the full military temperature range. The vendor's procedure shall be kept under document control and shall be made available upon request of the acquiring or preparing activity. 4. QUALITY ASSURANCE PROVISIONS 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL C SHEET 5 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ 2/ Group A subgroups -55°C ≤ TA ≤+125°C unless otherwise specified Device type Limits Min Unit Max DC parameters Input leakage current ILI VCC = 5.5 V dc, VIN = GND 1,2,3 All 10 µA 1,2,3 All 10 µA 1,2,3 All 140 mA 1,2,3 All 200 mA 1,2,3 All 6.5 mA 0.8 V or VCC Output leakage current ILO VCC = 5.5 V dc, VIN = GND or VCC VCC active current for read ICC1 CS = VIL, OE = VIH, f = 5 MHz, VCC = 5.5 V dc VCC active current for ICC2 program/erase 3/ VCC standby current CS = VIL, OE = VIH, f = 5 MHz, VCC = 5.5 V dc ISB CS = VIH, f = 5 MHz, VCC = 5.5 V dc Input low level 3/ VIL 1,2,3 All Input high level 3/ VIH 1,2,3 All Output low voltage VOL VCC = 4.5 V, IOL = 8.0 mA 1,2,3 All Output high voltage VOH1 VCC = 4.5 V, IOH = -2.5 mA 1,2,3 All 0.85 x VCC V VOH2 3/ VCC = 4.5 V, IOH = -100 µA 1,2,3 All VCC - 0.4 V 2.0 V 0.45 V V dc Dynamic characteristics OE capacitance COE VIN = 0 V, f = 1.0 MHz, 4 All 50 pF TA = +25° C See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL C SHEET 6 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ 2/ Group A subgroups -55°C ≤ TA ≤+125°C unless otherwise specified Device type Limits Min Unit Max Dynamic characterisitics - Continued A0-16 capacitance 3/ CAD VIN = 0 V, f = 1.0 MHz, 4 All 50 pF 4 All 20 pF 4 All 50 pF TA = +25° C CS capacitance 3/ CCS VIN = 0 V, f = 1.0 MHz, TA = +25° C WE capacitance 3/ CWE VIN = 0 V, f = 1.0 MHz, TA = +25° C, Case outline 4, only 20 Remaining case outlines I/O0-I/O31 capacitance 3/ CI/O VI/O = 0 V, f = 1.0 MHz, 4 All See 4.3.1c 7, 8A,8B All 20 pF TA = +25° C Functional testing Functional tests Read cycle AC timing characteristics Read cycle time 3/ tRC See figure 4 9,10,11 01 02 03 04 05 Address access time tACC See figure 4 9,10,11 01 02 03 04 05 150 120 90 70 60 ns Chip select access time tCE See figure 4 9,10,11 01 02 03 04 05 150 120 90 70 60 ns 150 120 90 70 60 ns See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL C SHEET 7 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ 2/ Group A subgroups -55°C ≤ TA ≤+125°C unless otherwise specified Device type Limits Min Unit Max Read cycle AC timing characteristics - Continued Output enable to output valid tOE See figure 4 9,10,11 01 02 03 04 05 55 50 40 35 30 ns Chip select to output high Z tDF See figure 4 9,10,11 01 02 03 04,05 35 30 25 20 ns OE high to output high Z 3/ tDF See figure 4 9,10,11 01 02 03 04,05 35 30 25 20 ns Output hold from address, CS or OE change, whichever is first 3/ tOH See figure 4 9,10,11 All 0 ns 3/ Write/Erase/Program AC timing characteristics WE controlled Write cycle time 3/ tWC See figure 5 9,10,11 01 02 03 04 05 150 120 90 70 60 ns Chip select setup time tCS See figure 5 9,10,11 All 0 ns Write enable pulse width tWP See figure 5 9,10,11 01,02 03 04 05 50 45 35 30 ns Address setup time tAS See figure 5 9,10,11 All 0 ns Data setup time tDS See figure 5 9,10,11 01,02 03 04,05 50 45 30 ns See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL C SHEET 8 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ 2/ Group A subgroups -55°C ≤ TA ≤+125°C unless otherwise specified Device type Limits Min Unit Max Write/Erase/Program AC timing characteristics WE controlled - Continued. Data hold time tDH See figure 5 9,10,11 All 0 ns Address hold time tAH See figure 5 9,10,11 01,02 03,04, 05 50 45 ns Write enable pulse high 3/ tWPH See figure 5 9,10,11 All 20 ns Read recovery before 3/ write tGHWL See figure 5 9,10,11 All 0 ns Write/Erase/Program AC timing characteristics CS controlled. Write cycle time 3/ tWC See figure 6 9,10,11 01 02 03 04 05 150 120 90 70 60 ns Write enable setup time tWS See figure 6 9,10,11 All 0 ns Chip select pulse width tCP See figure 6 9,10,11 01,02 03 04 05 50 45 35 30 ns Address setup time tAS See figure 6 9,10,11 All 0 ns Data hold time tDH See figure 6 9,10,11 All 0 ns Data setup time tDS See figure 6 9,10,11 01,02 03 04,05 50 45 30 ns See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL C SHEET 9 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ 2/ Group A subgroups -55°C ≤ TA ≤+125°C unless otherwise specified Device type Limits Min Unit Max Write/Erase/Program AC characteristics CS controlled - Continued. Address hold time tAH See figure 6 9,10,11 01,02 03,04, 05 50 45 ns Chip select pulse width high 3/ tCPH See figure 6 9,10,11 All 20 ns Read recovery before 3/ write tGHEL 9,10,11 All 0 ns 1/ Unless otherwise specified, 4.5 V dc ≤ V CC ≤ 5.5 V dc and V SS = 0 V. 2/ Unless otherwise specified, the DC test conditions are as follows: Input pulse levels: V = V - 0.3 V and V = 0.3V. IH CC IL Unless otherwise specified, the AC test conditions are as follows: Input pulse levels: V = 0 V and V = 3.0 V. IL IH Input rise and fall times: 5 nanoseconds. Input and output timing reference levels: 1.5 V. Output load circuit as specified in figure 8. 3/ Guaranteed by design, but not tested. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL C SHEET 10 Case outline M. FIGURE 1. Case outlines. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL C SHEET 11 Case outline M - Continued. Symbol Millimeters Inches Min Max Min Max A 3.12 5.10 .123 .200 A1 2.30 4.72 .118 .186 A2 0.24 0.64 .005 .025 b 0.33 0.43 .013 .017 B c 0.25 REF 0.23 D/E .010 REF 0.30 .009 20.3 BSC .012 .800 BSC D1/E1 22.10 22.65 .870 .890 D2/E2 24.89 25.35 .980 1.000 D3/E3 23.75 24.28 .936 .956 e 1.27 BSC .050 BSC R 0.25 BSC .010 BSC L1 0.89 1.14 .035 .045 NOTES: 1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Pin numbers are for reference only. 3. Case outline M may be either a single cavity or dual cavity package. Dimension A2 is measured between the lowest horizontal plane of the package and the seating plane of the lead(s). FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL C SHEET 12 Case outline N. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL C SHEET 13 Case outline N - Continued. Symbol Millimeters Inches Min Max Min Max A 3.12 4.06 .123 .160 A2 0.13 0.64 .005 .025 b 0.33 0.43 .013 .017 c 0.23 0.30 .009 .012 D/E 20.3 BSC .800 BSC D1/E1 22.10 22.65 .870 .890 D2/E2 24.89 25.35 .980 1.000 D3/E3 23.75 24.28 .936 .956 e 1.27 BSC .050 BSC R 0.25 BSC .010 BSC L1 0.89 1.14 .035 .045 NOTES: 1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Pin numbers are for reference only. 3. Case outline N is a single cavity package. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL C SHEET 14 Case outlines S, U, W, Y, 5, 6, 7, and 8. FIGURE 1. Case outlines- Continued. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL C SHEET 15 Case outlines S, U, W, and Y only. Symbol Millimeters Inches Min Max Min Max A 5.08 6.22 .200 .245 A1 0.64 0.89 .025 .035 φb 0.41 0.51 .016 .020 φb1 1.14 1.40 .045 .055 φb2 1.65 1.91 .065 .075 D/E 29.72 30.48 1.170 1.200 D1/E1 25.40 BSC 1.000 BSC D2 15.24 BSC .600 BSC D3 28.96 e L 29.21 1.020 2.54 BSC 3.68 1.150 .100 BSC 3.94 .132 .155 NOTES: 1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Pin 1 is identified by a 0.070 square pad. 3. Pin numbers are for reference only. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL C SHEET 16 Case outlines 5, 6, 7, and 8 only. Symbol Millimeters Inches Min Max Min Max A 3.43 4.34 .135 .181 A1 0.64 0.89 .025 .035 φb 0.41 0.51 .016 .020 φb1 1.14 1.40 .045 .055 φb2 1.65 1.91 .065 .075 D/E 27.05 27.56 1.065 1.085 D1/E1 25.40 BSC 1.000 BSC D2 15.24 BSC .600 BSC D3 25.90 e L 26.92 1.020 2.54 BSC 3.35 1.060 .100 BSC 3.94 .132 .155 NOTES: 1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Pin 1 is identified by a 0.070 square pad. 3. Pin numbers are for reference only. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL C SHEET 17 Case outlines T, V, X, and Z. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL C SHEET 18 Case outlines T, V, X, and Z - Continued. Symbol Millimeters Inches Min Max Min Max A 3.30 5.84 .130 .230 φb 0.41 0.51 .016 .020 φb1 0.76 REF .030 REF φb2 1.65 1.91 .065 .075 D/E 26.92 30.48 1.060 1.200 D1/E1 25.40 BSC 1.000 BSC D2 15.24 BSC .600 BSC D3 26.16 e L 29.21 1.030 2.54 BSC 4.19 1.150 .100 BSC 4.69 .165 .185 NOTES: 1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Pin 1 is identified by a 0.070 square pad. 3. Pin numbers are for reference only. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL C SHEET 19 Case outline 4. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL C SHEET 20 Case outline 4 - Continued. Symbol Millimeters Inches Min Max Min Max A 4.46 5.10 .175 .200 A1 1.40 1.65 .055 .065 A2 1.14 1.40 .045 .055 b 0.30 0.46 .012 .018 c 0.23 0.31 .009 .012 D/E 63.63 66.42 2.505 2.615 D1/E1 39.24 40.01 1.545 1.575 D2/E2 73.28 84.20 2.885 3.315 e 1.14 1.40 .045 .055 e1 20.19 20.45 .795 .805 j 4.83 5.33 .190 .210 k 37.72 38.48 1.485 1.515 L 12.19 13.21 .480 .520 S1 9.45 9.86 .372 .388 NOTES: 1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Pin numbers are for reference only. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL C SHEET 21 Case outline 9. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL C SHEET 22 Case outline 9 - Continued. Symbol Millimeters Min Inches Max Min Max A 3.56 .140 A1 2.79 .110 A2 0.46 0.76 .018 .030 b 0.33 0.43 .013 .017 C 0.15 0.25 .006 .010 D/E 20.32 TYP .800 TYP D1/E1 23.65 24.10 .931 .949 D2/E2 25.15 25.40 .990 1.000 e L1 1.27 TYP 0.51 .050 TYP 1.14 .020 .045 NOTES: 1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Pin numbers are for reference only. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL C SHEET 23 Device types All Device types All Device types All Device types All Case outlines M, N, 9 Case outlines M, N, 9 Case outlines M, N, 9 Case outlines M, N, 9 Terminal number Terminal symbol Terminal number Terminal symbol Terminal number Terminal symbol Terminal number Terminal symbol 1 GND 18 GND 35 OE 52 GND 2 CS3 19 I/O8 36 CS2 53 I/O23 3 A5 20 I/O9 37 NC 54 I/O22 4 A4 21 I/O10 38 WE2 55 I/O21 5 A3 22 I/O11 39 WE3 56 I/O20 6 A2 23 I/O12 40 WE4 57 I/O19 7 A1 24 I/O13 41 NC 58 I/O18 8 A0 25 I/O14 42 NC 59 I/O17 9 NC 26 I/O15 43 NC 60 I/O16 10 I/O0 27 VCC 44 I/O31 61 VCC 11 I/O1 28 A11 45 I/O30 62 A10 12 I/O2 29 A12 46 I/O29 63 A9 13 I/O3 30 A13 47 I/O28 64 A8 14 I/O4 31 A14 48 I/O27 65 A7 15 I/O5 32 A15 49 I/O26 66 A6 16 I/O6 33 A16 50 I/O25 67 WE1 17 I/O7 34 CS1 51 I/O24 68 CS4 FIGURE 2. Terminal connections. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL C SHEET 24 Device type All Device type All Device type All Device type All Case outlines U,V,Y,Z, 6,8 Case outlines U,V,Y,Z, 6,8 Case outlines U,V,Y,Z, 6,8 Case outlines U,V,Y,Z, 6,8 Terminal number Terminal symbol Terminal number Terminal symbol Terminal number Terminal symbol Terminal number Terminal symbol 1 I/O8 18 A15 35 I/O25 52 WE3 2 I/O9 19 VCC 36 I/O26 53 CS3 3 I/O10 20 CS1 37 A7 54 GND 4 A14 21 NC 38 A12 55 I/O19 5 A16 22 I/03 39 NC 56 I/O31 6 A11 23 I/015 40 A13 57 I/O30 7 A0 24 I/O14 41 A8 58 I/O29 8 NC 25 I/O13 42 I/O16 59 I/O28 9 I/O0 26 I/O12 43 I/O17 60 A1 10 I/O1 27 OE 44 I/O18 61 A2 11 I/O2 28 NC 45 VCC 62 A3 12 WE2 29 WE1 46 CS4 63 I/O23 13 CS2 30 I/O7 47 WE4 64 I/O22 14 GND 31 I/O6 48 I/O27 65 I/O21 15 I/O11 32 I/O5 49 A4 66 I/O20 16 A10 33 I/O4 50 A5 17 A9 34 I/O24 51 A6 NOTE: Case outlines Y, Z, and 8, pins 8, 21, 28, and 39 are no connects (NC) and for case outlines U, V, and 6, pins 8, 21, 28, and 39 are ground. FIGURE 2. Terminal connections (industrial pin-outs) - Continued. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL C SHEET 25 Device type All Device type All Device type All Device type All Case outlines S,T,W,X, 5,7 Case outlines S,T,W,X, 5,7 Case outlines S,T,W,X, 5,7 Case outlines S,T,W,X, 5,7 Terminal number Terminal symbol Terminal number Terminal symbol Terminal number Terminal symbol Terminal number Terminal symbol 1 I/O8 18 A12 35 I/O25 52 WE3 2 I/O9 19 VCC 36 I/O26 53 CS3 3 I/O10 20 CS1 37 A6 54 GND 4 A13 21 NC 38 A7 55 I/O19 5 A14 22 I/03 39 NC 56 I/O31 6 A15 23 I/015 40 A8 57 I/O30 7 A16 24 I/O14 41 A9 58 I/O29 8 NC 25 I/O13 42 I/O16 59 I/O28 9 I/O0 26 I/O12 43 I/O17 60 A0 10 I/O1 27 OE 44 I/O18 61 A1 11 I/O2 28 NC 45 VCC 62 A2 12 WE2 29 WE1 46 CS4 63 I/O23 13 CS2 30 I/O7 47 WE4 64 I/O22 14 GND 31 I/O6 48 I/O27 65 I/O21 15 I/O11 32 I/O5 49 A3 66 I/O20 16 A10 33 I/O4 50 A4 17 A11 34 I/O24 51 A5 NOTE: Case outlines W, X, and 7, pins 8, 21, 28, and 39 are no connects (NC) and for case outlines S, T, and 5, pins 8, 21, 28, and 39 are ground. FIGURE 2. Terminal connections (alternative pin-outs) - Continued. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL C SHEET 26 Device types All Device types All Device types All Device types All Case outline 4 Case outline 4 Case outline 4 Case outline 4 Terminal number Terminal symbol Terminal number Terminal symbol Terminal number Terminal symbol Terminal number Terminal symbol 1 GND 18 GND 35 OE 52 GND 2 CS1 19 I/O8 36 CS4 53 I/O23 3 A5 20 I/O9 37 NC 54 I/O22 4 A4 21 I/O10 38 NC 55 I/O21 5 A3 22 I/O11 39 NC 56 I/O20 6 A2 23 I/O12 40 NC 57 I/O19 7 A1 24 I/O13 41 NC 58 I/O18 8 A0 25 I/O14 42 NC 59 I/O17 9 NC 26 I/O15 43 NC 60 I/O16 10 I/O0 27 VCC 44 I/O31 61 VCC 11 I/O1 28 A11 45 I/O30 62 A10 12 I/O2 29 A12 46 I/O29 63 A9 13 I/O3 30 A13 47 I/O28 64 A8 14 I/O4 31 A14 48 I/O27 65 A7 15 I/O5 32 A15 49 I/O26 66 A6 16 I/O6 33 A16 50 I/O25 67 WE 17 I/O7 34 CS2 51 I/O24 68 CS3 FIGURE 2. Terminal connections - Continued. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL C SHEET 27 CS OE WE Data I/O MODE Device current H X X High Z Standby Standby L L H Data out Read Active L H L Data in Write Active NOTES: 1. H=V 2. L = V = Low Logic Level 3. 4. X = Do not care (either high or low) High Z = High Impedance State IH = High Logic Level IL FIGURE 3. Truth table. FIGURE 4. Read cycle timing diagram. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL C SHEET 28 FIGURE 5. Write/Erase/Program operations, WE controlled. NOTES: 1. PA represents the address of the memory location to be programmed. 2. PD represents the data to be programmed at byte address. 3. D7 is the output of the complement of the data written to the device. 4. DOUT is the output of the data written to the device. 5. Figures indicate last two bus cycles of a four bus cycle sequence. FIGURE 6. Write/Erase/Program operations, CS controlled. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL C SHEET 29 Case outlines M, N, S, T, U, V, W, X, Y, Z, 5, 6, 7, 8, and 9 Case outline 4. FIGURE 7. Block diagrams . STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL C SHEET 30 NOTES: 1. V is programmable from -2 V to +7 V. Z 2. I OL and I OH are programmable from 0 to 16 mA. 3. Tester impedance is Z = 75 ohms. 0 4. V is typically the midpoint of V Z 5. I OL OL and I OH and V . OH are adjusted to simulate a typical resistive load circuit. 6. ATE tester includes jig capacitance. FIGURE 8. Output load circuit. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL C SHEET 31 TABLE II. Electrical test requirements. MIL-PRF-38534 test requirements Subgroups (in accordance with MIL-PRF-38534, group A test table) Interim electrical parameters 1,4,7,9 Final electrical parameters 1*,2,3,4,7,8A,8B,9,10,11 Group A test requirements 1,2,3,4,7,8A,8B,9,10,11 Group C end-point electrical parameters 1,2,3,4,7,8A,8B,9,10,11 End-point electrical parameters for Radiation Hardness Assurance (RHA) devices Not applicable * PDA applies to subgroup 1. 4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition B. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DSCC-VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1015 of MIL-STD-883. (2) TA as specified in accordance with table I of method 1015 of MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. 4.3 Conformance and periodic inspections. Conformance inspection (CI) and periodic inspection (PI) shall be in accordance with MIL-PRF-38534 and as specified herein. 4.3.1 Group A inspection (CI). Group A inspection shall be in accordance with MIL-PRF-38534 and as follows: a. Tests shall be as specified in table II herein. b. Subgroups 5 and 6 shall be omitted. c. Subgroups 7, 8A, and 8B shall include verification of the truth table on figure 3. d. The following data patterns shall be verified during subgroups 7, 8A, and 8B. (1) 0's to all memory cell locations. (2) Checkerboard pattern to entire memory. (3) Checkerboard compliment to entire memory array. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL C SHEET 32 4.3.2 Group B inspection (PI). Group B inspection shall be in accordance with MIL-PRF-38534. 4.3.3 Group C inspection (PI). Group C inspection shall be in accordance with MIL-PRF-38534 and as follows: a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test, method 1005 of MIL-STD-883. (1) Test condition B. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DSCC-VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1005 of MIL-STD-883. (2) TA as specified in accordance with table I of method 1005 of MIL-STD-883. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. (4) The checkerboard data pattern shall be verified after burn-in as part of end-point electrical testing. 4.3.4 Group D inspection (PI). Group D inspection shall be in accordance with MIL-PRF-38534. 4.3.5 Radiation Hardness Assurance (RHA) inspection. RHA inspection is not currently applicable to this drawing. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38534. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-prepared specification or drawing. 6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated as specified in MIL-PRF-38534. 6.4 Record of users. Military and industrial users shall inform Defense Supply Center Columbus when a system application requires configuration control and the applicable SMD. DSCC will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices (FSC 5962) should contact DSCC-VA, telephone (614) 692-0544. 6.5 Comments. Comments on this drawing should be directed to DSCC-VA, Columbus, Ohio 43216-5000, or telephone (614) 692-0512. 6.6 Sources of supply. Sources of supply are listed in MIL-HDBK-103 and QML-38534. The vendors listed in MIL-HDBK-103 and QML-38534 have submitted a certificate of compliance (see 3.7 herein) to DSCC-VA and have agreed to this drawing. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-94716 A REVISION LEVEL C SHEET 33 STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 00-06-20 Approved sources of supply for SMD 5962-94716 are listed below for immediate acquisition information only and shall be added to MIL-HDBK-103 and QML-38534 during the next revisions. MIL-HDBK-103 and QML-38534 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DSCC-VA. This bulletin is superseded by the next dated revisions of MIL-HDBK-103 and QML-38534. Standard microcircuit drawing PIN 1/ 5962-9471601HMA 5962-9471601HMA 5962-9471601HMC 5962-9471601HMC 5962-9471601HNA 5962-9471601HNA 5962-9471601HNC 5962-9471601HNC 5962-9471601HSA 5962-9471601HSC 5962-9471601HTA 5962-9471601HTC 5962-9471601HUA 5962-9471601HUC 5962-9471601HVA 5962-9471601HVC 5962-9471601HWA 5962-9471601HWC 5962-9471601HXA 5962-9471601HXC 5962-9471601HYA 5962-9471601HYC 5962-9471601HZA 5962-9471601HZA 5962-9471601HZC 5962-9471601HZC 5962-9471601H4C 5962-9471601H5A 5962-9471601H5C 5962-9471601H6A 5962-9471601H6C 5962-9471601H7A 5962-9471601H7C 5962-9471601H8A 5962-9471601H8A 5962-9471601H8C 5962-9471601H8C 5962-9471601H9A 5962-9471601H9C Vendor CAGE number 54230 88379 54230 88379 54230 88379 54230 88379 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 88379 54230 88379 54230 54230 54230 54230 54230 54230 54230 54230 88379 54230 88379 54230 54230 1 of 6 Vendor similar PIN 2/ WF128K32-150G2Q5 ACT-F128K32N-150F5Q WF128K32-150G2Q5 ACT-F128K32N-150F5Q WF128K32-150G2UQ5 ACT-F128K32N-150F5Q WF128K32-150G2UQ5 ACT-F128K32N-150F5Q WF128K32A-150HQ5 WF128K32A-150HQ5 WF128K32A-150HSQ5 WF128K32A-150HSQ5 WF128K32-150HQ5 WF128K32-150HQ5 WF128K32-150HSQ5 WF128K32-150HSQ5 WF128K32NA-150HQ5 WF128K32NA-150HQ5 WF128K32NA-150HSQ5 WF128K32NA-150HSQ5 WF128K32N-150HQ5 WF128K32N-150HQ5 WF128K32N-150HSQ5 ACT-F128K32N-150P3Q WF128K32N-150HSQ5 ACT-F128K32N-150P3Q WF128K32-150G4Q5 WF128K32A-150H1Q5 WF128K32A-150H1Q5 WF128K32-150H1Q5 WF128K32-150H1Q5 WF128K32NA-150H1Q5 WF128K32NA-150H1Q5 WF128K32N-150H1Q5 ACT-F128K32N-150P7Q WF128K32N-150H1Q5 ACT-F128K32N-150P7Q WF128K32-150G1UQ5 WF128K32-150G1UQ5 STANDARD MICROCIRCUIT DRAWING SOURCE APPROVAL BULLETIN - Continued. DATE: 00-06-20 Standard microcircuit drawing PIN 1/ 5962-9471602HMA 5962-9471602HMA 5962-9471602HMC 5962-9471602HMC 5962-9471602HNA 5962-9471602HNA 5962-9471602HNC 5962-9471602HNC 5962-9471602HSA 5962-9471602HSC 5962-9471602HTA 5962-9471602HTC 5962-9471602HUA 5962-9471602HUC 5962-9471602HVA 5962-9471602HVC 5962-9471602HWA 5962-9471602HWC 5962-9471602HXA 5962-9471602HXC 5962-9471602HYA 5962-9471602HYC 5962-9471602HZA 5962-9471602HZA 5962-9471602HZC 5962-9471602HZC 5962-9471602H4C 5962-9471602H5A 5962-9471602H5C 5962-9471602H6A 5962-9471602H6C 5962-9471602H7A 5962-9471602H7C 5962-9471602H8A 5962-9471602H8A 5962-9471602H8C 5962-9471602H8C 5962-9471602H9A 5962-9471602H9C Vendor CAGE number 54230 88379 54230 88379 54230 88379 54230 88379 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 88379 54230 88379 54230 54230 54230 54230 54230 54230 54230 54230 88379 54230 88379 54230 54230 2 of 6 Vendor similar PIN 2/ WF128K32-120G2Q5 ACT-F128K32N-120F5Q WF128K32-120G2Q5 ACT-F128K32N-120F5Q WF128K32-120G2UQ5 ACT-F128K32N-120F5Q WF128K32-120G2UQ5 ACT-F128K32N-120F5Q WF128K32A-120HQ5 WF128K32A-120HQ5 WF128K32A-120HSQ5 WF128K32A-120HSQ5 WF128K32-120HQ5 WF128K32-120HQ5 WF128K32-120HSQ5 WF128K32-120HSQ5 WF128K32NA-120HQ5 WF128K32NA-120HQ5 WF128K32NA-120HSQ5 WF128K32NA-120HSQ5 WF128K32N-120HQ5 WF128K32N-120HQ5 WF128K32N-120HSQ5 ACT-F128K32N-120P3Q WF128K32N-120HSQ5 ACT-F128K32N-120P3Q WF128K32-120G4Q5 WF128K32A-120H1Q5 WF128K32A-120H1Q5 WF128K32-120H1Q5 WF128K32-120H1Q5 WF128K32NA-120H1Q5 WF128K32NA-120H1Q5 WF128K32N-120H1Q5 ACT-F128K32N-120P7Q WF128K32N-120H1Q5 ACT-F128K32N-120P7Q WF128K32-120G1UQ5 WF128K32-120G1UQ5 STANDARD MICROCIRCUIT DRAWING SOURCE APPROVAL BULLETIN - Continued. DATE: 00-06-20 Standard microcircuit drawing PIN 1/ 5962-9471603HMA 5962-9471603HMA 5962-9471603HMC 5962-9471603HMC 5962-9471603HNA 5962-9471603HNA 5962-9471603HNC 5962-9471603HNC 5962-9471603HSA 5962-9471603HSC 5962-9471603HTA 5962-9471603HTC 5962-9471603HUA 5962-9471603HUC 5962-9471603HVA 5962-9471603HVC 5962-9471603HWA 5962-9471603HWC 5962-9471603HXA 5962-9471603HXC 5962-9471603HYA 5962-9471603HYC 5962-9471603HZA 5962-9471603HZA 5962-9471603HZC 5962-9471603HZC 5962-9471603H4C 5962-9471603H5A 5962-9471603H5C 5962-9471603H6A 5962-9471603H6C 5962-9471603H7A 5962-9471603H7C 5962-9471603H8A 5962-9471603H8A 5962-9471603H8C 5962-9471603H8C 5962-9471603H9A 5962-9471603H9C Vendor CAGE number 54230 88379 54230 88379 54230 88379 54230 88379 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 88379 54230 88379 54230 54230 54230 54230 54230 54230 54230 54230 88379 54230 88379 54230 54230 3 of 6 Vendor similar PIN 2/ WF128K32-90G2Q5 ACT-F128K32N-090F5Q WF128K32-90G2Q5 ACT-F128K32N-090F5Q WF128K32-90G2UQ5 ACT-F128K32N-090F5Q WF128K32-90G2UQ5 ACT-F128K32N-090F5Q WF128K32A-90HQ5 WF128K32A-90HQ5 WF128K32A-90HSQ5 WF128K32A-90HSQ5 WF128K32-90HQ5 WF128K32-90HQ5 WF128K32-90HSQ5 WF128K32-90HSQ5 WF128K32NA-90HQ5 WF128K32NA-90HQ5 WF128K32NA-90HSQ5 WF128K32NA-90HSQ5 WF128K32N-90HQ5 WF128K32N-90HQ5 WF128K32N-90HSQ5 ACT-F128K32N-090P3Q WF128K32N-90HSQ5 ACT-F128K32N-090P3Q WF128K32-90G4Q5 WF128K32A-90H1Q5 WF128K32A-90H1Q5 WF128K32-90H1Q5 WF128K32-90H1Q5 WF128K32NA-90H1Q5 WF128K32NA-90H1Q5 WF128K32N-90H1Q5 ACT-F128K32N-090P7Q WF128K32N-90H1Q5 ACT-F128K32N-090P7Q WF128K32-90G1UQ5 WF128K32-90G1UQ5 STANDARD MICROCIRCUIT DRAWING SOURCE APPROVAL BULLETIN - Continued. DATE: 00-06-20 Standard microcircuit drawing PIN 1/ 5962-9471604HMA 5962-9471604HMA 5962-9471604HMC 5962-9471604HMC 5962-9471604HNA 5962-9471604HNA 5962-9471604HNC 5962-9471604HNC 5962-9471604HSA 5962-9471604HSC 5962-9471604HTA 5962-9471604HTC 5962-9471604HUA 5962-9471604HUC 5962-9471604HVA 5962-9471604HVC 5962-9471604HWA 5962-9471604HWC 5962-9471604HXA 5962-9471604HXC 5962-9471604HYA 5962-9471604HYC 5962-9471604HZA 5962-9471604HZA 5962-9471604HZC 5962-9471604HZC 5962-9471604H4C 5962-9471604H5A 5962-9471604H5C 5962-9471604H6A 5962-9471604H6C 5962-9471604H7A 5962-9471604H7C 5962-9471604H8A 5962-9471604H8A 5962-9471604H8C 5962-9471604H8C 5962-9471604H9A 5962-9471604H9C Vendor CAGE number 54230 88379 54230 88379 54230 88379 54230 88379 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 88379 54230 88379 54230 54230 54230 54230 54230 54230 54230 54230 88379 54230 88379 54230 54230 4 of 6 Vendor similar PIN 2/ WF128K32-70G2Q5 ACT-F128K32N-070F5Q WF128K32-70G2Q5 ACT-F128K32N-070F5Q WF128K32-70G2UQ5 ACT-F128K32N-070F5Q WF128K32-70G2UQ5 ACT-F128K32N-070F5Q WF128K32A-70HQ5 WF128K32A-70HQ5 WF128K32A-70HSQ5 WF128K32A-70HSQ5 WF128K32-70HQ5 WF128K32-70HQ5 WF128K32-70HSQ5 WF128K32-70HSQ5 WF128K32NA-70HQ5 WF128K32NA-70HQ5 WF128K32NA-70HSQ5 WF128K32NA-70HSQ5 WF128K32N-70HQ5 WF128K32N-70HQ5 WF128K32N-70HSQ5 ACT-F128K32N-070P3Q WF128K32N-70HSQ5 ACT-F128K32N-070P3Q WF128K32-70G4Q5 WF128K32A-70H1Q5 WF128K32A-70H1Q5 WF128K32-70H1Q5 WF128K32-70H1Q5 WF128K32NA-70H1Q5 WF128K32NA-70H1Q5 WF128K32N-70H1Q5 ACT-F128K32N-070P7Q WF128K32N-70H1Q5 ACT-F128K32N-070P7Q WF128K32-70G1UQ5 WF128K32-70G1UQ5 STANDARD MICROCIRCUIT DRAWING SOURCE APPROVAL BULLETIN - Continued. DATE: 00-06-20 Standard microcircuit drawing PIN 1/ 5962-9471605HMA 5962-9471605HMA 5962-9471605HMC 5962-9471605HMC 5962-9471605HNA 5962-9471605HNA 5962-9471605HNC 5962-9471605HNC 5962-9471605HSA 5962-9471605HSC 5962-9471605HTA 5962-9471605HTC 5962-9471605HUA 5962-9471605HUC 5962-9471605HVA 5962-9471605HVC 5962-9471605HWA 5962-9471605HWC 5962-9471605HXA 5962-9471605HXC 5962-9471605HYA 5962-9471605HYC 5962-9471605HZA 5962-9471605HZA 5962-9471605HZC 5962-9471605HZC 5962-9471605H4C 5962-9471605H5A 5962-9471605H5C 5962-9471605H6A 5962-9471605H6C 5962-9471605H7A 5962-9471605H7C 5962-9471605H8A 5962-9471605H8A 5962-9471605H8C 5962-9471605H8C 5962-9471605H9A 5962-9471605H9C Vendor CAGE number 54230 88379 54230 88379 54230 88379 54230 88379 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 54230 88379 54230 88379 54230 54230 54230 54230 54230 54230 54230 54230 88379 54230 88379 54230 54230 Vendor similar PIN 2/ WF128K32-60G2Q5 ACT-F128K32N-060F5Q WF128K32-60G2Q5 ACT-F128K32N-060F5Q WF128K32-60G2UQ5 ACT-F128K32N-060F5Q WF128K32-60G2UQ5 ACT-F128K32N-060F5Q WF128K32A-60HQ5 WF128K32A-60HQ5 WF128K32A-60HSQ5 WF128K32A-60HSQ5 WF128K32-60HQ5 WF128K32-60HQ5 WF128K32-60HSQ5 WF128K32-60HSQ5 WF128K32NA-60HQ5 WF128K32NA-60HQ5 WF128K32NA-60HSQ5 WF128K32NA-60HSQ5 WF128K32N-60HQ5 WF128K32N-60HQ5 WF128K32N-60HSQ5 ACT-F128K32N-060P3Q WF128K32N-60HSQ5 ACT-F128K32N-060P3Q WF128K32-60G4Q5 WF128K32A-60H1Q5 WF128K32A-60H1Q5 WF128K32-60H1Q5 WF128K32-60H1Q5 WF128K32NA-60H1Q5 WF128K32NA-60H1Q5 WF128K32N-60H1Q5 ACT-F128K32N-060P7Q WF128K32N-60H1Q5 ACT-F128K32N-060P7Q WF128K32-60G1UQ5 WF128K32-60G1UQ5 1/ The lead finish shown for each PIN representing a hermetic package is the most readily available from the manufacturer listed for that part. If the desired lead finish is not listed contact the vendor for its availability. 2/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. 5 of 6 STANDARD MICROCIRCUIT DRAWING SOURCE APPROVAL BULLETIN - Continued. DATE: 00-06-20 Vendor CAGE number Vendor name and address 54230 White Electronic Designs Corporation 3601 East University Drive Phoenix, AZ 85034-7217 88379 Aeroflex Circuit Technology 35 South Service Road Plainview NY, 11803-4193 The information contained herein is disseminated for convenience only and the Government assumes no liability whatsoever for any inaccuracies in the information bulletin. 6 of 6