KSP2907A tm PNP General Purpose Amplifier Features • Collector-Emitter Voltage: VCEO= 60V • Collector Power Dissipation: PC (max)=625mW • Suffix “-C” means a Center Collector (1.Emitter 2.Collector 3.Base) TO-92 • Non suffix “-C” means a Side Collector (1.Emitter 2.Base 3.Collector) • Available as PN2907A 1 2 3 KSP2907A : 1. Emitter 2. Base 3. Collector KSP2907AC : 1. Emitter 2. Collector 3. Base Absolute Maximum Ratings * T a Symbol VCBO VCEO VEBO IC TJ Tstg = 25°C unless otherwise noted Parameter Collector-Base Voltage Collector-Emitter Voltage Emitter-Base Voltage Collector current Junction Temperature Storage Temperature Value Units -60 -60 -5 -600 +150 -55 ~ +150 V V V mA °C °C * 1. These ratings are limiting values above which the serviceability of any semiconductor device may be impaired. 2. These are steady state limits. The factory should be consulted on applications involving pulsed or low duty cycle operations. Thermal Characteristics T =25°C unless otherwise noted a Symbol PC RθJC RθJA Parameter Max Units Collector Power Dissipation, by RθJA Thermal Resistance, Junction to Case(note1) Thermal Resistance, Junction to Ambient(note2) 625 83.3 200 mW °C/W °C/W Note1. Infinite heat sink. Note2. Minimum Land pad size. Electrical Characteristics * T a Symbol V(BR)CBO V(BR)CEO V(BR)EBO ICBO hFE = 25°C unless otherwise noted Parameter Collector-Base Breakdown Voltage Collector-Emitter Breakdown Voltage Emitter-Base Breakdown Voltage Collector Cutoff Current DC Current Gain VCE(sat) Collector-Emitter Saturation Voltage VBE(sat) Base-Emitter Saturation Voltage Cobo fT Output Capacitance Current Gain Bandwidth Product tON tOFF Turn On Time Turn Off Time Test Condition IC = -10µA, IE = 0 IC = -10mA, IB = 0 IE = -10µA, IC = 0 VCB = -50V, IE = 0 VCE = -10V, IC = -0.1mA, VCE = -10V, IC = -1mA, VCE = -10V, IC = -10mA, VCE = -10V, IC = -150mA, VCE = -10V, IC = -500mA, IC = -150mA, IB = -15mA IC = -500mA, IB = -50mA IC = -150mA, IB = -15mA IC = -500mA, IB = -50mA VCB = -10V, IE = 0, f = 1.0MHz IC = -50mA, VCE = -20V, f = 100MHz VCC= -30V, IC = -150mA, IB1= -15mA VCC= -6V, IC = -150mA,IB1= IB1 = -15mA Min. Typ. Max. Units -60 -60 -5.0 -10 75 100 100 100 50 V V V nA 300 -0.4 -1.6 -1.3 -2.6 8 V V V V pF MHz 45 100 ns ns 200 * DC Item are tested by Pulse Test: Pulse Width≤300us, Duty Cycle≤2% ©2006 Fairchild Semiconductor Corporation KSP2907A Rev. E 1 www.fairchildsemi.com KSP2907A PNP General Purpose Amplifier September 2006 Device(note) Device Marking Package Packing Method Qty(pcs) Pin Definitions KSP2907ABU KSP2907A TO-92 BULK -- 1.Emitter 2.Base 3.Collector KSP2907ACBU KSP2907AC TO-92 BULK -- 1.Emitter 2.Collector 3.Base KSP2907ATA KSP2907A TO-92 TAPE & AMMO 2,000 1.Emitter 2.Base 3.Collector KSP2907ACTA KSP2907AC TO-92 TAPE & AMMO 2,000 1.Emitter 2.Collector 3.Base KSP2907ATF KSP2907A TO-92 TAPE & REEL 2,000 1.Emitter 2.Base 3.Collector Note : Affix “-C-” - center collector pin. Suffix “-BU” - Bulk packing, straight lead form.(see package dimensions) Suffix “-TF” - Tape& Reel packing, 0.200 In-Line Spacing lead form. (see package dimensions) SUffix “-TA” - Tape& AMMO packing, 0.200 In-Line Spacing lead form. (see package dimensions) 2 KSP2907A Rev. E www.fairchildsemi.com KSP2907A PNP General Purpose Amplifier Package Marking and Ordering Information VBE(sat), VCE(sat)[V], SATURATION VOLTAGE 1000 hFE, DC CURRENT GAIN VCE = -10V 100 -10 IC = 10 IB -0.1 VCE(sat) -0.01 10 -1 -10 -100 VBE(sat) -1 -1 -1000 -100 -1000 IC[mA], COLLECTOR CURRENT IC[A], COLLECTOR CURRENT Figure 2. Collector-Emitter Saturation Voltage Base-Emitter Saturation Voltage Figure 1. DC current Gain 100 fT[MHz], CURRENT GAIN BANDWIDTH PRODUCT 1000 IE = 0 f = 1MHz Cob [pF], CAPACITANCE -10 10 1 0.1 -1 -10 -100 100 10 -1 -10 -100 -1000 IC[mA], COLLECTOR CURRENT VCB [V], COLLECTOR-BASE VOLTAGE Figure 3. Output Capacitance Figure 4. Current Gain Bandwidth Product 3 KSP2907A Rev. E VCE = -20V www.fairchildsemi.com KSP2907A PNP General Purpose Amplifier Typical Characteristics KSP2907A PNP General Purpose Amplifier Package Dimensions TO-92 Straight Lead Form +0.25 4.58 ±0.20 4.58 –0.15 14.47 ±0.40 0.46 ±0.10 1.27TYP [1.27 ±0.20] 1.27TYP [1.27 ±0.20] +0.10 0.38 –0.05 (0.25) +0.10 0.38 –0.05 1.02 ±0.10 3.86MAX 3.60 ±0.20 (R2.29) Dimensions in Millimeters Dimensions in Millime TO-92 0.200 In-Line Spacing Lead Form Dimensions in Inches[Millimeters] 4 KSP2907A Rev. E www.fairchildsemi.com The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not intended to be an exhaustive list of all such trademarks. ACEx™ ActiveArray™ Bottomless™ Build it Now™ CoolFET™ CROSSVOLT™ DOME™ EcoSPARK™ E2CMOS™ EnSigna™ FACT™ FAST® FASTr™ FPS™ FRFET™ FACT Quiet Series™ GlobalOptoisolator™ GTO™ HiSeC™ I2C™ i-Lo™ ImpliedDisconnect™ IntelliMAX™ ISOPLANAR™ LittleFET™ MICROCOUPLER™ MicroFET™ MicroPak™ MICROWIRE™ MSX™ MSXPro™ Across the board. Around the world.™ The Power Franchise® Programmable Active Droop™ OCX™ OCXPro™ OPTOLOGIC® OPTOPLANAR™ PACMAN™ POP™ Power247™ PowerEdge™ PowerSaver™ PowerTrench® QFET® QS™ QT Optoelectronics™ Quiet Series™ RapidConfigure™ RapidConnect™ µSerDes™ ScalarPump™ SILENT SWITCHER® SMART START™ SPM™ Stealth™ SuperFET™ SuperSOT™-3 SuperSOT™-6 SuperSOT™-8 SyncFET™ TCM™ TinyBoost™ TinyBuck™ TinyPWM™ TinyPower™ TinyLogic® TINYOPTO™ TruTranslation™ UHC™ UltraFET® UniFET™ VCX™ Wire™ DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN;NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESE SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILD’S WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY THEREIN, WHICH COVERS THESE PRODUCTS. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, or (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. PRODUCT STATUS DEFINITIONS Definition of Terms Datasheet Identification Product Status Definition Advance Information Formative or In Design This datasheet contains the design specifications for product development. Specifications may change in any manner without notice. Preliminary First Production This datasheet contains preliminary data, and supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. No Identification Needed Full Production This datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. Obsolete Not In Production This datasheet contains specifications on a product that has been discontinued by Fairchild semiconductor. The datasheet is printed for reference information only. Rev. I20 5 KSP2907A Rev. E www.fairchildsemi.com KSP2907A PNP General Purpose Amplifier TRADEMARKS