( 5 : 1 )

F
E
D
C
B
n1,8 (2x)
NOTES:
1. METALSHELLS: COPPER ALLOY; min. 315µin TIN over 40-80µin NICKEL
2. INSULATORS: PBT GF UL 94 V-0; GREEN
3. SIGNAL CONTACTS: COPPER ALLOY; PLATING: GOLD FLASH over NICKEL
SOLDER CUP ACCEPTS CABLE AWG 20
4. HIGH POWER CONTACTS 10A: COPPER ALLOY
PLATING MATING AREA: GOLD FLASH over NICKEL
PLATING TERMINATION SIDE: GOLD FLASH over NICKEL
SOLDER CUP ACCEPTS CABLE AWG 16 - 20
5. RUBBER GASKET: TPE; BLACK
6. CONNECTOR IS PART MARKED: 4017W2PAM61A10X CONEC ABC
(5:1)
D
53,09 +- 0,33
0,44
POS. 1
9,46 +- 0,34
0,26
16,63 +- 0,12
0,38
n1,12 (15x)
38,86 +- 0,23
0,02
POS. A1
6 +- 00,31
47,04 `0,13
POS. 8
0,9
D
A
C
C
8,26 +- 0,22
0,03
12,6 +- 0,33
0,43
10°
RUBBER GASKET
PLACED ON TOP SURFACE
OF MALE INSULATOR
SEALING
COMPOUND
1,3 +- 0,3
0,1
4017W2PAM61A10X CONEC ABC
n3,1 `0,1
see note 6
B
B
Solder Instruction
TITLE:
COMPANY NAME:
APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION # APPROVAL
F
E
DO NOT ALTER CAD DRAWING BY HAND
NAME:
THIS DRAWING MAY NOT BE COPIED OR
REPRODUCED IN ANY WAY, AND MAY NOT
BE PASSED ON TO A THIRD PARTY WITHOUT
WRITTEN PERMISSION.
OWNERSHIP AND COPYRIGHT OF CONEC GmbH
APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION # APPROVAL
CUSTOMER APPROVAL DATE:
APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION
A
APPROVAL # FREIGABE # DEBLOCAGE # AUTORIZACION
1. Cable should be prepared for soldering. The cable/wires must be pretinned.
2. Insert cable/wire into solder cup.
3. Signal Contact
3.1. Operate the soldering iron at 350°C, 50 Watt m ax. and use a pencil tip.
3.2. Put tip to wire in solder cup.
3.3. After 1 second bring in solder.
3.4. Heat for 3 seconds longer. Do not heat contact more than 4 seconds in total.
4. Power Contact
4.1. Operate the soldering iron at 350°C, 100 Watt max. and use a pencil tip.
4.2. Put tip to wire in solder cup.
4.3. After 1 second bring in solder.
4.4. Heat for 5 seconds longer. Do not heat contact more than 6 seconds in total.
5. Remove soldering iron.
6. Wait until solder gets rigid again.
7. Do not solder adjacent contacts consecutively,
alternate position within the connector to minimize heat build up.
scale:
material:
tolerance
2:1 (5:1)
see notes
dim. in mm
A
title:
date
name
drawn
15.10.10
Schmidt
D-SUB COMBINATION MALE
appd.
15.10.10
Koch
17W2P
for installation into water resistant hood
dwg no:
Inventor 10
DIN-
norm
d-old
Origin
rev. description
D
date
part no:
name
C
A3
sh: 1
15K1A732
R
a
B
4017W2PAM61A10X
A