TFS1516A - Vectron International

Filename: tfs 1516a.doc
Version 1.1
Vectron International
09.12.2009
Filter specification
TFS 1516A
1/5
Measurement condition
Ambient temperature:
Input power level:
Terminating impedance: *
Input:
Output:
23
0
°C
dBm
253 Ω || -0,40 pF
74 Ω || -0,45 pF
Characteristics
Remark:
The nominal frequency fN is fixed at 1516,0 MHz. The insertion loss ae is defined as loss value determined at fN. Reference level for the relative
attenuation arel of the TFS 1516A is the insertion loss ae. All specified data are met within the operating temperature range.
Data
typ. value
ae
Insertion loss
(reference level)
Nominal frequency
Passband
fN
-
PB
1,2
Pass band variation
MHz
MHz
MHz
MHz
MHz
MHz
MHz
...
...
...
...
...
...
...
dB
max.
3,0
1516,0
fN
dB
max.
±
dB
MHz
20,0
MHz
2,0
dB
arel
Relative attenuation
0,3
860
1100
1608,4
1724,6
2000
2250
2,1
tolerance / limit
860
1100
1423,9
1724,6
2000
2250
6000
MHz
MHz
MHz
MHz
MHz
MHz
MHz
64
58
50
43
47
48
50
dB
dB
dB
dB
dB
dB
dB
min.
min.
min.
min.
min.
min.
min.
55
46
40
33
40
36
15
dB
dB
dB
dB
dB
dB
dB
1534,5
MHz
13
ns
max.
15
ns
Group delay ripple
1497,4
MHz ...
Input VSWR within PB
1,5 : 1
max.
2,4 : 1
Output VSWR within PB
1,5 : 1
max.
2,4 : 1
max.
Permissible DC voltage
Operable temperature range
Operating temperature range
OTR
Storage temperature range
Temperature coefficient of frequency
TCf **
0
-
- 30 °C ... + 80 °C
-
- 20 °C ... + 50 °C
-
- 50 °C ... +125 °C
- 44
V
ppm/K
*) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference
values only. Should there be additional questions do not hesitate to ask for an application note or contact our design team.
**) ∆f(Hz) = TCf(ppm/K) x (T-T0) x fTo(MHz)
Generated:
Checked / Approved:
Vectron International GmbH & Co. KG
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without
notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such
product(s) or information.
Filename: tfs 1516a.doc
Version 1.1
Vectron International
09.12.2009
Filter specification
TFS 1516A
2/5
Filter characteristic
insertion loss: -2.34 dB
0
0
-10
-1
-20
-2
-30
-3
-40
-4
0.04
0.038
0.034
-50
-60
0.032
0.03
0.028
-5
0.026
-6
-70
-7
-80
-8
-90
-9
delay inµs
magnitude indB
magnitude in dB
0.036
0.024
0.022
0.02
0.018
-100
8
607.8
1207.6
1807.4
2407.2
3007
3606.8
frequency in MHz
4206.6
4806.4
5406.2
6006
0.016
-10
1472
1480
1488
1496
1504
1512
1520
frequency in MHz
1528
1536
1544
0.014
1552
Construction and pin connection
(All dimensions in mm)
G16A
● X50
1
2
3
4
5
6
7
8
Input
Input
Ground
Ground
Output
Output
Ground
Ground
Date code:
X
A
B
...
Year + week
2009
2010
2011
150 Ω / 150 Ω Test circuit
L1
150 Ohm
C1
L2
5
1
2
SAW
6
L2
C2
150 Ohm
L4
3,4,7, 8
Vectron International GmbH & Co. KG
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without
notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such
product(s) or information.
Filename: tfs 1516a.doc
Version 1.1
Vectron International
09.12.2009
Filter specification
TFS 1516A
3/5
Stability characteristics, reliability
After the following tests the filter shall meet the whole specification:
1. Shock:
500g, 1 ms, half sine wave, 3 shocks each plane;
DIN IEC 68 T2 - 27
2. Vibration:
10 Hz to 500 Hz, 0,35 mm or 5 g respectively, 1 octave per min, 10 cycles per plan, 3 plans;
DIN IEC 68 T2 - 6
3. Change of
temperature:
4. Resistance to
solder heat (reflow):
5. ESD
-55 °C to 125°C / 30 min. each / 10 cycles
DIN IEC 68 part 2 – 14 Test N
reflow possible: three times max.;
for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4;
MIL-STD-883E using coupling network of ISO 10605 and EN 6100-4-2
HBM:250V; CDM:V;
This filter is RoHS compliant (2002/95/EG, 2005/618/EG)
Packing
Tape & Reel:
IEC 286 – 3, with exception of value for N and minimum bending radius;
tape type II, embossed carrier tape with top cover tape on the upper side;
max. pieces of filters per reel:
reel of empty components at start:
reel of empty components at start including leader:
trailer:
9000
min. 300 mm
min. 500 mm
min. 300 mm
Pull Off Direction
Tape (all dimensions in mm)
W
: 8,00 ± 0,3
Po
: 4,00 ± 0,1
Do
: 1,50 +0,1/-0
E
: 1,75 ± 0,1
F
: 3,50 ± 0,05
G(min)
: 0,75
P2
: 2,00 ± 0,05
P1
: 4,00 ± 0,1
D1(min)
: 1,50
Ao
: 3,25 ± 0,1
Bo
: 3,25 ± 0,1
Ct
: 5,5 ± 0,1
P1
Date Code
Do
P2
W
G
Ct
Bo
F
G
E
t
Po
Ko
Typ
PIN Marker
D1
Ao
W 2
Reel (all dimensions in mm)
A
: 330
W1
: 8,4 +1,5/-0
W2(max) : 14,4
N(min)
: 50
C
: 13,0 +0,5/-0,2
A
C
N
W 1
The minimum bending radius is 45 mm.
Vectron International GmbH & Co. KG
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without
notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such
product(s) or information.
Filename: tfs 1516a.doc
Version 1.1
Vectron International
09.12.2009
Filter specification
TFS 1516A
4/5
Air reflow temperature conditions
Conditions
Average ramp-up rate (30°C to 217°C)
> 100°C
> 150°C
> 217°C
Peak temperature
Time within 5°C of actual peak temperature
Cool-down rate (Peak to 50°C)
Time from 30°C to Peak temperature
Exposure
less than 3°C/second
between 300 and 600 seconds
between 240 and 500 seconds
between 30 and 150 seconds
max. 260°C
between 10 and 30 seconds
less than 6°C/second
no greater than 300 seconds
Chip-mount air reflow profile
Temperature / °C
max. 260°C
217°C
max. 300 s
10 ... 30 s
Time / s
30 ... 150 s
Vectron International GmbH & Co. KG
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without
notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such
product(s) or information.
Filename: tfs 1516a.doc
Vectron International
Version 1.1
Filter specification
09.12.2009
TFS 1516A
5/5
History
Version
Reason of Changes
Name
Date
1.0
- Generation of development specification
S. Channaa
28.09.2009
1.1
- Add typical values and filter characteristic
- Generation of filter specification
S. Channaa
09.12.2009
Vectron International GmbH & Co. KG
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without
notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such
product(s) or information.