20W AC-DC Power-Supply PAC20C ● ● ● ● ● ● ● PCB-mountable plastic case 85 … 264 VAC or 120 … 370 VDC universal input range Continuously short circuit protected Over voltage protected Isolation class II MTBF > 300000 hours 3 years product warranty Model selection guide Type PAC20C03S PAC20C05S PAC20C09S PAC20C12S PAC20C15S PAC20C24S Output voltage [VDC] 3.3 5.0 9.0 12 15 24 Output voltage tolerance [%] typ. ±2 ±2 ±2 ±2 ±2 ±2 Output current Output power Efficiency @ full load Stand by consumption Capacitive load [mA] max. 4100 3500 2100 1600 1300 850 [W] max. 9.9 17.5 18.9 19.2 19.5 20.4 [%] typ. 73 75 77 81 83 85 [W] typ. 0.1 0.1 0.1 0.1 0.1 0.1 [µF] max. 48000 12000 7200 5400 2700 1800 Specification Input Voltage range Line frequency range Full load input current Inrush current Recommended fuse Isolation Isolation voltage (input to output) Leakage current Isolation resistance Output Voltage accuracy Line regulation Temperature coefficient Ripple & noise up to 20 MHz Output load regulation @ load change 10 to 100% Minimum load Hold up time Protection Short circuit Over current Over voltage protection PAC20C3R3S, PAC20C05S PAC20C09S PAC20C12S, PAC20C15S PAC20C24S General Switching frequency Reliability MTBF@ 25°C 85..264 VAC or 120..370 VDC Power derating see diagram 47…63 Hz 600 mA @ 115 VAC, typ. 340 mA @ 230 VAC, typ. 16 A typ. @ 115 VAC 30 A typ. @ 230 VAC 2 A / 250V slow blow 3000 VAC for 1 min. tested 0.3 mA typ. @ Vin 230 VAC 8 10 Ω ±2% ± 0.5 % ± 0.02 % / °C 150 mV max. ± 1 %, typ. not required 15 ms typ. @ 115 VAC 80 ms typ. @ 230 VAC Continuous, auto recovery 110 %, min. of full load 7.5 VDC max. 12 VDC max. 20 VDC max. 30 VDC max. 65 kHz typ. > 300000 h EMC compliance EMI; Conducted & Radiation (without external circuit) EMS; Electrostatic discharge EMS; Radiation immunity field susceptibility EMS; Fast transients on mainsline (without external circuit) EMS; Fast transients on mainsline (with external circuit Fig. 2) EMS; Surge immunity (without external circuit) EMS; Surge immunity (with external circuit Fig. 2) EMS; Conducted Disturbance immunity EMS; Immunity for Power frequency magnetic field EMS; Immunities of voltage dip, drop and short interruption Safety approvals Safety Environmental Operating temperature (ambient) Storage temperature Case temperature Storage humidity Cooling Physical Dimensions, PCB version Weight Case material Wave soldering temperature CE: EN55011 (CISPR22), class B RE: EN55011 (CISPR22), class B IEC-, EN61000-4-2, air ± 8 kV, contact ± 6 kV, perf. Criteria B IEC-, EN61000-4-3, 10 V / m perf. Criteria A IEC-, EN61000-4-4, ± 2 kV, perf. Criteria B IEC-, EN61000-4-4, ± 4 kV, perf. Criteria B IEC, EN61000-4-5, ± 1 kV / ± 2 kV, perf. Criteria B IEC, EN61000-4-5, ± 2 kV / ± 4 kV, perf. Criteria B IEC-, EN61000-4-6, 10 Vrms perf. Criteria A IEC-, EN61000-4-8, 10 A/m perf. Criteria A IEC-, EN61000-4-11, 0…70% perf. Criteria B EN60950, UL60950 Class I -40 °C to 70 °C (with derating) -25 °C to +105 °C 90 °C, max. 95 %, non condensing Free air convection 70 x 48 x 23.5 mm 120 g UL94V-0 rated 260 ± 5 °C, 10 s max., 1.5 mm distance min. from case Manual soldering temperature 360 ± 10 °C, 5 s max., 1.5 mm distance min. from case Page 1 of 5 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Hochstrasse 355 CH-8200 Schaffhausen Tel.: 052 647 42 00 E-Mail: [email protected] 20W AC-DC Power-Supply PAC20C Output ripple & noise measure circuit Conductor track Oscilloscope probe L AC line voltage AC DC N PE C1 C2 10µF 100nF 25.4mm Typical application L F1 L C1 D1 +Vout C2 +Vo R2 U N 25.4mm PAC20C R1 Figure 1 Load -Vout -Vo N PE PE Application circuit and example for ripple and noise reduction L F1 R1 L2 PIF001B PAC20C L1 L - Cy Figure 2 V +V out +V out Cx Cy PE U C1 C2 D1 -V out -V out N N -20 dB Noise reduction PE Optional filter module PIF001B contain following components: V, Cx, L1, L2 and Cy Table for discrete external components Model PAC20C03S PAC20C05S PAC20C09S PAC20C12S PAC20C15S PAC20C24S R1 NTC type F1 Slow blow fuse V MOV type 5D-9 5D-9 5D-9 5D-9 5D-9 5D-9 3.15A / 250V~ 3.15A / 250V~ 3.15A / 250V~ 3.15A / 250V~ 3.15A / 250V~ 3.15A / 250V~ S14K350 S14K350 S14K350 S14K350 S14K350 S14K350 Cx 250 V~ L2 [µF] 0.1 0.1 0.1 0.1 0.1 0.1 [µH] 5 5 5 5 5 5 L1 Common mode [mH] 10 10 10 10 10 10 Cy 400 V~ [nF] 1 1 1 1 1 1 C1 Cer.cap. [µF] 1 1 1 1 1 1 C2 El. Cap. [µF] 330 330 220 220 220 220 D1 TVS type SMBJ7.0A SMBJ7.0A SMBJ12A SMBJ20A SMBJ20A SMBJ30A Note: Output filtering capacitor C2 is an electrolytic capacitor. It is recommended to apply an electrolytic capacitor for high frequency and low resistance. For capacitance and current please refer the capacitor data sheet. Capacitance withstand voltage derating should be 80 % or above. C1 is a ceramic capacitor, which is used to filter high frequency noise. TVS diode D1 is a recommended component to protect post circuits if the converter module fails. Page 2 of 5 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Hochstrasse 355 CH-8200 Schaffhausen Tel.: 052 647 42 00 E-Mail: [email protected] 20W AC-DC Power-Supply PAC20C PCB layout with the front end filter modul PIF001B Suggestions for safety regulation and wiring width: wire width ≥ 3mm, distance between wires ≥ 6 mm, and distance between wire and ground ≥ 6 mm Application note for trim option Trim down circuit Trim up circuit +Vout PAC20C R1 - +Vout PAC20C Rtd - R3 + R1 R3 + R2 VRef VRef -Vout Model series PAC20Cxx03S PAC20Cxx05S PAC20Cxx09S PAC20Cxx12S PAC20Cxx15S PAC20Cxx24S Rtu R2 R1 [kΩ] 3.3 3.3 7.5 3.83 7.5 8.66 R2 [kΩ] 1.98 3.3 2.87 1 1.5 1 -Vout R3 [kΩ] 1 1 1 1 1 1 V Ref [V] 1.24 2.5 2.5 2.5 2.5 2.5 Rtd min. [kΩ] 16 12.2 44 23.95 54 63.9 Rtu min. [kΩ] 11.66 15.5 20.63 7.5 11.5 8.62 Page 3 of 5 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Hochstrasse 355 CH-8200 Schaffhausen Tel.: 052 647 42 00 E-Mail: [email protected] 20W AC-DC Power-Supply PAC20C Page 4 of 5 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Hochstrasse 355 CH-8200 Schaffhausen Tel.: 052 647 42 00 E-Mail: [email protected] 20W AC-DC Power-Supply PAC20C Dimensions Pin connection Pin 1 2 3 4 5 6 7 8 9 Pin configuration PE Input AC (N) Input AC (L) - V output No pin No pin No pin + V output Trim input Unit: mm Pin diameter tolerance: ± 0.1 mm Pin length: >6 mm General tolerances: ± 0.5 mm Note: 1. 2. Unless otherwise specified, data in this datasheet should be tested under the conditions of Ta 25 °C, humidity < 75 % at nominal input voltage and rated output load current. Module are not hot swappable! PHI-CON is a trademark of HY-LINE Holding GmbH. Only for professional use by professionals! Not for resale or distribution to the general public in any way! Read the instructions for use carefully before using! Life Support Policy: HY-LINE does not authorize the use of any of its products for use in life support devices or systems without the express written approval of an officer of the Company. Life support systems are devices which support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. Rev: 09.15 f Page 5 of 5 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Hochstrasse 355 CH-8200 Schaffhausen Tel.: 052 647 42 00 E-Mail: [email protected]