SPT7734 8-BIT, 40 MSPS,175 mW A/D CONVERTER FEATURES APPLICATIONS • • • • • • • • • • • All High-Speed Applications Where Low Power Dissipation is Required • Video Imaging • Medical Imaging • Radar Receivers • IR Imaging • Digital Communications Monolithic 40 MSPS Converter 175 mW Power Dissipation On-Chip Track-and-Hold Single +5 V Power Supply TTL/CMOS Outputs 5 pF Input Capacitance Low Cost Tri-State Output Buffers High ESD Protection: 3,500 V Minimum Selectable +3 V or +5 V Logic I/O GENERAL DESCRIPTION The SPT7734 is a 8-bit monolithic, low cost, ultralow power analog-to-digital converter capable of minimum word rates of 40 MSPS. The on-chip track-and-hold function assures very good dynamic performance without the need for external components. The input drive requirements are minimized due to the SPT7734's low input capacitance of only 5 pF. Power dissipation is extremely low at only 175 mW typical at 40 MSPS with a power supply of +5.0 V. The digital outputs BLOCK DIAGRAM AAA AAA AAA AAA AAA AAA are +3 V or +5 V, and are user selectable. The SPT7734 has incorporated proprietary circuit design and CMOS processing technologies to achieve its advanced performance. Inputs and outputs are TTL/CMOS compatible to interface with TTL/CMOS logic systems. Output data format is straight binary. The SPT7734 is available in 28-lead SOIC and 32-lead small (7 mm square) TQFP packages over the commercial temperature range. ADC Section 1 AIN 1:16 Mux P1 AutoZero CMP T/H 9-Bit SAR 9 D8 Overrange 9 D7 (MSB) DAC D6 P2 CLK In Enable .. Timing . P15 and Control P16 . . . . . . . . . ADC Section 15 AAA AAA AAA AAA AAA AAA ADC Section 16 T/H Data Vali d 9 ADC Section 2 AutoZero CMP 9 9-Bit SAR 9 9-Bit 16:1 Mux/ Error Correction D5 D4 D3 D2 9 D1 DAC DØ (LSB) Ref In Reference Ladder VREF ABSOLUTE MAXIMUM RATINGS (Beyond which damage may occur)1 25 °C Supply Voltages AVDD ......................................................................... +6 V DVDD ........................................................................ +6 V Output Digital Outputs ....................................................... 10 mA Temperature Operating Temperature ................................. 0 to +70 °C Junction Temperature ......................................... +175 °C Lead Temperature, (soldering 10 seconds) ........ +300 °C Storage Temperature ................................ -65 to +150 °C Input Voltages Analog Input .................................. -0.5 V to AVDD +0.5 V VREF ............................................................................ 0 to AVDD CLK Input .................................................................. VDD AVDD - DVDD ............................................................... ±100 mV AGND - DGND ................................................... ±100 mV Note: 1. Operation at any Absolute Maximum Rating is not implied. See Electrical Specifications for proper nominal applied conditions in typical applications. ELECTRICAL SPECIFICATIONS T A=TMAX to TMAX, AV DD =DV DD =+5.0 V, V IN =0 to 4 V, f S=40 MSPS, V RHS =4.0 V, V RLS =0.0 V, unless otherwise specified. PARAMETERS TEST CONDITIONS TEST LEVEL Resolution MIN SPT7734 TYP MAX 8 DC Accuracy Integral Nonlinearity Differential Nonlinearity No Missing Codes IV IV VI Analog Input Input Voltage Range Input Resistance Input Capacitance Input Bandwidth Offset Gain Error VI IV V V V V VRLS 50 (Small Signal) Bits ±1.0 ±0.5 Guaranteed LSB LSB VRHS V kΩ pF MHz LSB LSB Ω MHz 5.0 250 UNITS ±2.0 ±2.0 Reference Input Resistance Bandwidth Voltage Range VRLS VRHS VRHS - VRLS ∆(VRHF - VRHS) ∆(VRLS - VRLF) VI V 300 100 500 150 600 IV IV V V V 0 3.0 1.0 4.0 90 75 2.0 AVDD 5.0 Reference Settling Time VRHS VRLS V V Conversion Characteristics Maximum Conversion Rate Minimum Conversion Rate Pipeline Delay (Latency) Aperture Delay Time Aperture Jitter Time VI IV IV V V 40 2 Dynamic Performance Effective Number of Bits fIN=3.58 MHz fIN=10.3 MHz VI VI 7.3 7.2 15 20 V V V mV mV Clock Cycles Clock Cycles MHz MHz 12 Clock Cycles 4.0 30 ns ps(p-p) 7.8 7.7 Bits Bits SPT7734 2 1/27/98 ELECTRICAL SPECIFICATIONS T A=TMAX to TMAX, AV DD =DV DD =+5.0 V, V IN =0 to 4 V, f S=40 MSPS, V RHS =4.0 V, V RLS =0.0 V, unless otherwise specified. PARAMETERS Dynamic Performance Signal-to-Noise Ratio (without Harmonics) fIN=3.58 MHz fIN=10.3 MHz Harmonic Distortion fIN=3.58 MHz fIN=10.3 MHz Signal-to-Noise and Distortion (SINAD) fIN=3.58 MHz fIN=10.3 MHz Spurious Free Dynamic Range Differential Phase Differential Gain Intermodulation Distortion TEST CONDITIONS TEST LEVEL 9 Distortion bins from 1024 pt FFT fIN=1.0 MHz IOH = 0.5 mA IOL = 1.6 mA 15 pF load 15 pF load 20 pF load, TA = +25 °C 50 pF load over temp. Power Supply Requirements Voltages OVDD DVDD AVDD Currents AIDD DIDD Power Dissipation All electrical characteristics are subject to the following conditions: All parameters having min/max specifications are guaranteed. The Test Level column indicates the specific device testing actually performed during production and Quality Assurance inspection. Any blank section in the data column indicates that the specification is not tested at the specified condition. TEST LEVEL MAX UNITS VI VI 46 45 49 48 dB dB VI VI 53 53 57 56 dB dB VI VI 46 45 49 48 dB dB VI VI VI VI V TEST LEVEL CODES SPT7734 TYP V V V Inputs Logic 1 Voltage Logic 0 Voltage Maximum Input Current Low Maximum Input Current High Input Capacitance Digital Outputs Logic 1 Voltage Logic 0 Voltage tRISE tFALL Output Enable to Data Output Delay MIN 63 ±0.3 ±0.3 TBD dB Degree % dB 2.0 0.8 +10 +10 -10 -10 +5 VI VI V V V V 3.5 IV IV IV VI VI VI 3.0 4.75 4.75 0.4 10 10 10 22 5.0 5.0 17 18 175 5.0 5.25 5.25 22 23 225 V V µA µA pF V V ns ns ns ns V V V mA mA mW TEST PROCEDURE I 100% production tested at the specified temperature. II 100% production tested at TA=25 °C, and sample tested at the specified temperatures. III QA sample tested only at the specified temperatures. IV Parameter is guaranteed (but not tested) by design and characterization data. V Parameter is a typical value for information purposes only. VI 100% production tested at TA = 25 °C. Parameter is guaranteed over specified temperature range. SPT7734 3 1/27/98 Figure 1A: Timing Diagram 1 AAA A A A A A A A A A A A A AAA A A A A A A A A A A A A AAA A A A A AA AA A 1 ANALOG IN CLOCK IN SAMPLING CLOCK (Internal) DATA OUTPUT DATA VALID A A A A A A A AA A A A A A A A A AA A A A AA A AAA AAAAAA AAAAAA AAA AAAAAA AAAAAA AAA AAAAAA AAA 11 A A A A A A A AA A A A A A A A A AA A A A AA A A AAAA AAAA AAAA AAAA AA AAAA AA 9 3 AAAAAA AAA AAAAAA AAAAAA AAA AAAAAA AAA 7 5 INVALID AA AAAAAAAAA A AA A A AAAAAAA A AA A A AAAAAAA A AA A A AAAAAA AAAAAAA A AA A A AAAAAA AAAAA 13 17 15 VALID 1 2 3 4 5 Figure 1B: Timing Diagram 2 tCLK tC tCH tCL CLOCK IN DATA OUTPUT Data Ø Data 1 Data 2 Data 3 tOD tS DATA VALID tCH tCL tS Table I - Timing Parameters DESCRIPTION PARAMETERS MIN tC tCLK ns tCLK 25 ns Clock High Duty Cycle tCH 40 50 60 % Clock Low Duty Cycle tCL 40 50 60 % Clock to Output Delay (15 pF Load) tOD 17 ns Clock to DAV tS 10 ns Conversion Time Clock Period TYP MAX UNITS SPT7734 4 1/27/98 TYPICAL INTERFACE CIRCUIT The high sample rate is achieved by using multiple SAR ADC sections in parallel, each of which samples the input signal in sequence. Each ADC uses 16 clock cycles to complete a conversion. The clock cycles are allocated as follows: Very few external components are required to achieve the stated device performance. Figure 1 shows the typical interface requirements when using the SPT7734 in normal circuit operation. The following sections provide descriptions of the major functions and outline critical performance criteria to consider for achieving the optimal device performance. Table II - Clock Cycles Clock 1 2 3 4 5-15 16 Figure 1 - Typical Interface Circuit Ref In (+4 V) VRHF D8 VRHS VRLS VRLF VIN VIN SPT7734 D0 VCAL CLK CLK IN The 16 phase clock, which is derived from the input clock, synchronizes these events. The timing signals for adjacent ADC sections are shifted by one clock cycle so that the analog input is sampled on every cycle of the input clock by exactly one ADC section. After 16 clock periods, the timing cycle repeats. The latency from analog input sample to the corresponding digital output is 12 clock cycles. Interfacing Logics EN DAV AVDD AGND DGND* DVDD • Since only 16 comparators are used, a huge power savings is realized. FB1 +D5 FB2 • The auto-zero operation is done using a closed loop system that uses multiple samples of the comparators response to a reference zero. Enable/Tri-State (Enable = Active Low) +A5 FB3 AGND +A5 DGND + 10 µF +5 V Analog +5 V Analog RTN *To reduce the possibility of latch-up, avoid connecting the DGND pins of the ADC to the digital ground of the system. Operation Reference zero sampling Auto-zero comparison Auto-calibrate comparison Input sample 9-bit SAR conversion Data transfer • The auto-calibrate operation, which calibrates the gain of the MSB reference and the LSB reference, is also done with a closed loop system. Multiple samples of the gain error are integrated to produce a calibration voltage for each ADC section. +D5 + 10 µF +5 V Digital RTN +5 V Digital • Capacitive displacement currents, which can induce sampling error, are minimized since only one comparator samples the input during a clock cycle. NOTES: 1) FB3 is to be located as closely to the device as possible. 2) There should be no additional connections to the right of FB1 and FB2. 3) All capacitors are 0.1 µF surface-mount unless otherwise specified. 4) FB1, FB2 and FB3 are 10 µH inductors or ferrite beads. • The total input capacitance is very low since sections of the converter which are not sampling the signal are isolated from the input by transmission gates. POWER SUPPLIES AND GROUNDING Fairchild suggests that both the digital and the analog supply voltages on the SPT7734 be derived from a single analog supply as shown in figure 1. A separate digital supply should be used for all interface circuitry. Fairchild suggests using this power supply configuration to prevent a possible latchup condition on power up. VOLTAGE REFERENCE The SPT7734 requires the use of a single external voltage reference for driving the high side of the reference ladder. It must be within the range of 3 V to 5 V. The lower side of the ladder is typically tied to AGND (0.0 V), but can be run up to 2.0 V with a second reference. The analog input voltage range will track the total voltage difference measured between the ladder sense lines, VRHS and VRLS. OPERATING DESCRIPTION The general architecture for the CMOS ADC is shown in the block diagram. The design contains 16 identical successive approximation ADC sections, all operating in parallel, a 16phase clock generator, an 9-bit 16:1 digital output multiplexer, correction logic, and a voltage reference generator which provides common reference levels for each ADC section. Force and sense taps are provided to ensure accurate and stable setting of the upper and lower ladder sense line voltages across part-to-part and temperature variations. By using the configuration shown in figure 2, offset and gain errors of less than ±2 LSB can be obtained. SPT7734 5 1/27/98 Figure 2 - Ladder Force/Sense Circuit 1 + - 2 3 4 5 + Figure 3 - Simplified Reference Ladder Drive Circuit Without Force/Sense Circuit AGND +4.0 V External Reference VRHF 90 mV VRHS (+3.91 V) R/2 R VRHS R N/C R R=30 Ω (typ) All capacitors are 0.01 µF R VRLS R 6 7 VRLF R VRLS (0.075 V) VIN 75 mV R/2 VRLF (AGND) 0.0 V All capacitors are 0.01 µF In cases where wider variations in offset and gain can be tolerated, VRef can be tied directly to VRHF and AGND can be tied directly to VRLF as shown in figure 3. Decouple force and sense lines to AGND with a .01 µF capacitor (chip cap preferred) to minimize high-frequency noise injection. If this simplified configuration is used, the following considerations should be taken into account: The drive requirements for the analog inputs are very minimal when compared to most other converters due to the SPT7734's extremely low input capacitance of only 5 pF and very high input resistance in excess of 50 kΩ. The reference ladder circuit shown in figure 3 is a simplified representation of the actual reference ladder with force and sense taps shown. Due to the actual internal structure of the ladder, the voltage drop from VRHF to VRHS is not equivalent to the voltage drop from VRLF to VRLS. CALIBRATION The analog input should be protected through a series resistor and diode clamping circuit as shown in figure 4. The SPT7734 uses an auto calibration scheme to ensure 8-bit accuracy over time and temperature. Gain and offset errors are continually adjusted to 8-bit accuracy during device operation. This process is completely transparent to the user. Typically, the top side voltage drop for VRHF to VRHS will equal: Upon power-up, the SPT7734 begins its calibration algorithm. In order to achieve the calibration accuracy required, the offset and gain adjustment step size is a fraction of a 8bit LSB. Since the calibration algorithm is an oversampling process, a minimum of 10,000 clock cycles are required. This results in a minimum calibration time upon power-up of 250 µsec (for a 40 MHz clock). Once calibrated, the SPT7734 remains calibrated over time and temperature. VRHF - VRHS = 2.25 % of (VRHF - VRLF) (typical), and the bottom side voltage drop for VRLS to VRLF will equal: VRLS - VRLF = 1.9 % of (VRHF - VRLF) (typical). Figure 3 shows an example of expected voltage drops for a specific case. Vref of 4.0 V is applied to VRHF and VRLF is tied to AGND. A 90 mV drop is seen at VRHS (= 3.91 V) and a 75 mV increase is seen at VRLS (= 0.075 V). Since the calibration cycles are initiated on the rising edge of the clock, the clock must be continuously applied for the SPT7734 to remain in calibration. ANALOG INPUT VIN is the analog input. The input voltage range is from VRLS to VRHS (typically 4.0 V) and will scale proportionally with respect to the voltage reference. (See voltage reference section.) INPUT PROTECTION All I/O pads are protected with an on-chip protection circuit shown in figure 5. This circuit provides ESD robustness to 3.5 kV and prevents latch-up under severe discharge conditions without degrading analog transition times. SPT7734 6 1/27/98 DIGITAL OUTPUTS Figure 4 - Recommended Input Protection Circuit +V The digital outputs (D0-D8) are driven by a separate supply (OVDD) ranging from +3 V to +5 V. This feature makes it possible to drive the SPT7734's TTL/CMOS-compatible outputs with the user's logic system supply. The format of the output data (D0-D7) is straight binary. (See table III.) The outputs are latched on the rising edge of CLK. These outputs can be switched into a tri-state mode by bringing EN high. AVDD D1 Buffer ADC 47 Ω Table III - Output Data Information D2 -V D1 = D2 = Hewlett Packard HP5712 or equivalent ANALOG INPUT OVERRANGE D8 OUTPUT CODE D7-D0 +F.S. + 1/2 LSB 1 1111 1111 +F.S. -1/2 LSB O 1111 111Ø +1/2 F.S. O ØØØØ ØØØØ +1/2 LSB O OOOO OOOØ 0.0 V O OOOO OOOO (Ø indicates the flickering bit between logic 0 and 1). Figure 5 - On-Chip Protection Circuit DO NOT CONNECT PINS (DNC) There are two pins designated as Do Not Connect (DNC). These pins must be left floating for proper operation of the device. VDD 120 Ω Analog OVERRANGE OUTPUT The OVERRANGE OUTPUT (D8) is an indication that the analog input signal has exceeded the positive full scale input voltage by 1 LSB. When this condition occurs, D8 will switch to logic 1. All other data outputs (D0 to D7) will remain at logic 1 as long as D8 remains at logic 1. This feature makes it possible to include the SPT7734 into higher resolution systems. 120 Ω Pad CLOCK INPUT The SPT7734 is driven from a single-ended TTL-input clock. Because the pipelined architecture operates on the rising edge of the clock input, the device can operate over a wide range of input clock duty cycles without degrading the dynamic performance. SPT7734 7 1/27/98 PACKAGE OUTLINES 32-Lead TQFP INCHES A SYMBOL G H B C D I E MIN MILLIMETERS MAX MIN MAX A 0.347 0.355 8.90 9.10 B 0.269 0.277 6.90 7.10 C 0.347 0.355 8.90 9.10 D 0.269 0.277 6.90 7.10 E 0.027 0.035 0.68 0.89 F 0.012 0.018 0.30 0.45 G 0.053 0.057 1.35 1.45 H 0.002 0.006 0.05 0.15 I 0.039 typ 1.00 typ J 0.004 0.008 0.09 K 0° 7° 0° 0.20 7° L 0.018 0.029 0.45 0.75 J F K L 28-Lead SOIC SYMBOL A B C D E F G H I 28 I H 1 A MIN INCHES MAX 0.696 0.004 0.712 0.012 .050 typ 0.019 0.012 0.100 0.050 0.419 0.299 0.014 0.009 0.080 0.016 0.394 0.291 MILLIMETERS MIN MAX 17.68 0.10 0.00 0.36 0.23 2.03 0.41 10.01 7.39 18.08 0.30 1.27 0.48 0.30 2.54 1.27 10.64 7.59 H F B C D G E SPT7734 8 1/27/98 PIN ASSIGNMENTS PIN FUNCTIONS Name Function AGND Analog Ground VRHF Reference High Force VRHS Reference High Sense VRLS Reference Low Sense VRLF Reference Low Force VCAL Calibration Reference VIN Analog Input AVDD Analog VDD DVDD Digital VDD DGND Digital Ground CLK Input Clock fCLK =fs (TTL) D6 EN Output Enable 25 D0-7 Tri-State Data Output, (DØ=LSB) D8 Tri-State Output Overrange DAV Data Valid Output AGND 1 28 D8 2 27 D7 VRHS 3 26 D6 4 25 D5 VRLS 5 24 D4 VRLF 6 23 D3 VIN 7 22 OVDD AGND 8 21 OGND VCAL 9 20 D2 AVDD 10 19 D1 1 1 18 D0 DGND 12 17 DNC CLK 13 16 DNC DAV 14 15 EN VRHF N/C DVDD SOIC D7 D8 AGND AGND VRHF VRHS VRLS 26 27 28 29 31 30 32 VRLF 1 24 D5 VIN 2 23 D4 AGND 3 22 D3 AGND 4 21 OVDD OVDD Digital Output Supply OGND Digital Output Ground DNC Do Not Connect VCAL AVD D AVD D DVDD TQFP 20 OGND 6 19 D2 7 18 D1 8 17 D0 5 15 DAV EN DNC DNC 14 CLK 16 13 DGND DGND 12 10 DVDD 1 1 9 ORDERING INFORMATION PART NUMBER SPT7734SCS SPT7734SCT TEMPERATURE RANGE 0 to +70 °C 0 to +70 °C PACKAGE TYPE 28L SOIC 32L TQFP DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.fairchildsemi.com © Copyright 2002 Fairchild Semiconductor Corporation SPT7734 9 1/27/98