TSX561, TSX562, TSX564, TSX561A, TSX562A, TSX564A Micropower, wide bandwidth (900 kHz), 16 V CMOS operational amplifiers Datasheet - production data Benefits Single • Power savings in power-conscious applications • Easy interfacing with high impedance sensors Related products SOT23-5 • See TSX63x series for reduced power consumption (45 μA, 200 kHz) • See TSX92x series for higher gain bandwidth products (10 MHz) Dual DFN8 2x2 Applications MiniSO8 • Industrial and automotive signal conditioning • Active filtering • Medical instrumentation • High impedance sensors Quad QFN16 3x3 Description TSSOP14 Features • Low power consumption: 235 µA typ. at 5 V • Supply voltage: 3 V to 16 V • Gain bandwidth product: 900 kHz typ. • Low offset voltage – “A” version: 600 µV max. – Standard version: 1 mV max. • Low input bias current: 1 pA typ. • High tolerance to ESD: 4 kV • Wide temperature range: -40 to +125 °C • Automotive qualification • Tiny packages available – SOT23-5 – DFN8 2 mm x 2 mm, MiniSO8 – QFN16 3 mm x 3 mm, TSSOP14 May 2013 This is information on a product in full production. The TSX56x, TSX56xA series of operational amplifiers benefits from STMicroelectronics® 16 V CMOS technology to offer state-of-the-art accuracy and performance in the smallest industrial packages. The TSX56x, TSX56xA have pinouts compatible with industry standards and offer an outstanding speed/power consumption ratio, 900 kHz gain bandwidth product while consuming only 250 µA at 16 V. Such features make the TSX56x, TSX56xA ideal for sensor interfaces and industrial signal conditioning. The wide temperature range and high ESD tolerance ease use in harsh automotive applications. Table 1. Device summary Version Standard Vio Enhanced Vio Single TSX561 TSX561A Dual TSX562 TSX562A Quad TSX564 TSX564A DocID023274 Rev 3 1/27 www.st.com 27 Contents TSX56x, TSX56xA Contents 1 Pin connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Absolute maximum ratings and operating conditions . . . . . . . . . . . . . 4 3 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 5 4.1 Operating voltages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 4.2 Rail-to-rail input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 4.3 Input offset voltage drift over temperature . . . . . . . . . . . . . . . . . . . . . . . . 15 4.4 Long term input offset voltage drift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 4.5 PCB layouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 4.6 Macromodel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 5.1 SOT23-5 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 5.2 DFN8 2x2 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 5.3 MiniSO8 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 5.4 QFN16 3x3 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 5.5 TSSOP14 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 6 Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 7 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 2/27 DocID023274 Rev 3 TSX56x, TSX56xA Pin connections Figure 1. Pin connections for each package (top view) Single SOT23-5 (TSX561) Dual 287 9&& 287 9&& ,1 287 ,1 287 ,1 ,1 ,1 ,1 9&& ,1 9&& ,1 DFN8 2x2 (TSX562) MiniSO8 (TSX562) ,1 287 287 ,1 Quad ,1 9&& 9&& 1& 1& ,1 ,1 ,1 287 287 ,1 ,1 1 Pin connections QFN16 3x3 (TSX564) DocID023274 Rev 3 TSSOP14 (TSX564) 3/27 Absolute maximum ratings and operating conditions 2 TSX56x, TSX56xA Absolute maximum ratings and operating conditions Table 2. Absolute maximum ratings (AMR) Symbol VCC Vid Vin Iin Tstg Rthja Rthjc Tj Parameter Supply voltage (2) ±VCC V (3) VCC- - 0.2 to VCC++ 0.2 (4) 10 mA -65 to +150 °C Input voltage Storage temperature Thermal resistance junction to ambient SOT23-5 DFN8 2x2 MiniSO8 QFN16 3x3 TSSOP14 (5)(6) 250 120 190 80 100 °C/W Thermal resistance junction to case DFN8 2x2 QFN16 3x 33 30 Maximum junction temperature 150 °C 4 kV HBM: human body ESD Unit 18 Differential input voltage Input current Value (1) model(7) MM: machine model for TSX561(8) MM: machine model for TSX562 and 200 TSX564(8) 100 V CDM: charged device model(9) 1.5 kV Latch-up immunity 200 mA 1. All voltage values, except differential voltage, are with respect to network ground terminal. 2. The differential voltage is the non-inverting input terminal with respect to the inverting input terminal. 3. VCC - Vin must not exceed 18 V, Vin must not exceed 18 V. 4. Input current must be limited by a resistor in series with the inputs. 5. Short-circuits can cause excessive heating and destructive dissipation. 6. Rth are typical values. 7. Human body model: 100 pF discharged through a 1.5 kΩ resistor between two pins of the device, done for all couples of pin combinations with other pins floating. 8. Machine model: a 200 pF cap is charged to the specified voltage, then discharged directly between two pins of the device with no external series resistor (internal resistor < 5 Ω), done for all couples of pin combinations with other pins floating. 9. Charged device model: all pins plus package are charged together to the specified voltage and then discharged directly to ground. Table 3. Operating conditions Symbol 4/27 Parameter VCC Supply voltage Vicm Common mode input voltage range Toper Operating free air temperature range Value 3 to 16 DocID023274 Rev 3 VCC- - 0.1 to VCC+ + 0.1 -40 to +125 Unit V °C TSX56x, TSX56xA 3 Electrical characteristics Electrical characteristics Table 4. Electrical characteristics at VCC+ = +3.3 V with VCC- = 0 V, Vicm = VCC/2, Tamb = 25 °C, and RL=10 kΩ connected to VCC/2 (unless otherwise specified) Symbol Parameter Conditions Min. Typ. Max. Unit DC performance Vio Offset voltage TSX56xA, T = 25 °C 600 TSX56xA, -40 °C < T < 125 °C 1800 TSX56x, T = 25 °C 1 TSX56x, -40 °C < T < 125 °C 2.2 Input offset voltage drift -40 °C < T < 125 °C(1) 2 12 Iio Input offset current (Vout = VCC/2) T = 25 °C 1 100(2) -40 °C < T < 125 °C 1 200(2) Iib Input bias current (Vout = VCC/2) T = 25 °C 1 100(2) -40 °C < T < 125 °C 1 200(2) ΔVio/ΔT T = 25 °C 63 -40 °C < T < 125 °C 59 47 CMR1 T = 25 °C CMR2 Common mode rejection ratio CMR = 20 log (ΔVic/ΔVio) (Vic = -0.1 V to VCC+0.1 V, Vout = VCC/2, RL > 1 MΩ) -40 °C < T < 125 °C 45 Large signal voltage gain (Vout = 0.5 V to (VCC - 0.5 V), RL > 1 MΩ) T = 25 °C 85 Avd -40 °C < T < 125 °C 83 VOH High level output voltage (VOH = VCC - Vout) T = 25 °C 70 -40 °C < T < 125 °C 100 T = 25 °C 70 -40 °C < T < 125 °C 100 Low level output voltage Isink (Vout = VCC) Iout Isource (Vout = 0 V) ICC Supply current (per channel, Vout = VCC/2, RL > 1 MΩ) mV μV/°C pA 80 Common mode rejection ratio CMR = 20 log (ΔVic/ΔVio) (Vic = -0.1 V to VCC-1.5 V, Vout = VCC/2, RL > 1 MΩ) VOL μV 66 dB T = 25 °C 4.3 -40 °C < T < 125 °C 2.5 T = 25 °C 3.3 -40 °C < T < 125 °C 2.5 T = 25 °C -40 °C < T < 125 °C DocID023274 Rev 3 mV 5.3 mA 4.3 220 300 350 µA 5/27 Electrical characteristics TSX56x, TSX56xA Table 4. Electrical characteristics at VCC+ = +3.3 V with VCC- = 0 V, Vicm = VCC/2, Tamb = 25 °C, and RL=10 kΩ connected to VCC/2 (unless otherwise specified) (continued) Symbol Parameter Conditions Min. Typ. 600 800 Max. Unit AC performance GBP Gain bandwidth product Fu Unity gain frequency Φm Phase margin Gm Gain margin SR Slew rate ∫ en en THD+N RL = 10 kΩ, CL = 100 pF kHz 55 Degree 9 dB RL = 10 kΩ, CL = 100 pF, Vout = 0.5 V to VCC - 0.5 V 1 V/μs Low-frequency peak-to-peak input noise Bandwidth: f = 0.1 to 10 Hz 16 µVpp Equivalent input noise voltage density f = 1 kHz f = 10 kHz 55 29 nV -----------Hz 0.004 % Follower configuration, fin = 1 kHz, Total harmonic distortion + noise RL = 100 kΩ, Vicm = (VCC -1.5 V)/2, BW = 22 kHz, Vout = 1 Vpp 1. See Section 4.3: Input offset voltage drift over temperature on page 15. 2. Guaranteed by design. 6/27 690 DocID023274 Rev 3 TSX56x, TSX56xA Electrical characteristics Table 5. Electrical characteristics at VCC+ = +5 V with VCC- = 0 V, Vicm = VCC/2, Tamb = 25 °C, and RL = 10 kΩ connected to VCC/2 (unless otherwise specified) Symbol Parameter Conditions Min. Typ. Max. Unit DC performance Vio Offset voltage TSX56xA, T = 25 °C 600 TSX56xA, -40 °C < T < 125 °C 1800 TSX56x, T = 25 °C 1 TSX56x, -40 °C < T < 125 °C 2.2 Input offset voltage drift -40 °C < T < 125 °C(1) 2 Long-term input offset voltage drift T = 25 °C(2) 5 Iio Input offset current (Vout = VCC/2) T = 25 °C 1 100(3) -40 °C < T < 125 °C 1 200(3) Iib Input bias current (Vout = VCC/2) T = 25 °C 1 100(3) -40 °C < T < 125 °C 1 200(3) ΔVio/ΔT ΔVio 66 CMR1 Common mode rejection ratio T = 25 °C CMR = 20 log (ΔVic/ΔVio) (Vic = -0.1 V to VCC - 1.5 V, -40 °C < T < 125 °C Vout = VCC/2, RL > 1 MΩ) 50 CMR2 Common mode rejection ratio T = 25 °C CMR = 20 log (ΔVic/ΔVio) (Vic = -0.1 V to VCC + 0.1 V, -40 °C < T < 125 °C Vout = VCC/2, RL > 1 MΩ) 12 63 69 dB 47 85 -40 °C < T < 125 °C 83 VOH High level output voltage (VOH = VCC - Vout) RL = 10 kΩ, T = 25 °C RL = 10 kΩ, -40 °C < T < 125 °C 70 100 Low level output voltage RL = 10 kΩ, T = 25 °C RL = 10 kΩ, -40 °C < T < 125 °C 70 100 Isource ICC Supply current (per channel, Vout = VCC/2, RL > 1 MΩ) Vout = VCC, T = 25 °C 11 Vout = VCC, -40 °C < T < 125 °C 8 Vout = 0 V, T = 25 °C 9 Vout = 0 V, -40 °C < T < 125 °C 7 T = 25 °C -40 °C < T < 125 °C DocID023274 Rev 3 pA 84 T = 25 °C Iout μV/°C nV month Large signal voltage gain (Vout = 0.5 V to (VCC - 0.5 V), RL > 1 MΩ) Isink mV --------------------------- Avd VOL μV mV 14 mA 12 235 350 400 µA 7/27 Electrical characteristics TSX56x, TSX56xA Table 5. Electrical characteristics at VCC+ = +5 V with VCC- = 0 V, Vicm = VCC/2, Tamb = 25 °C, and RL = 10 kΩ connected to VCC/2 (unless otherwise specified) (continued) Symbol Parameter Conditions Min. Typ. 700 850 Max. Unit AC performance GBP Gain bandwidth product Fu Unity gain frequency Φm Phase margin Gm Gain margin SR Slew rate ∫ en Low-frequency peak-to-peak input noise en THD+N RL = 10 kΩ, CL = 100 pF kHz 55 Degree 9 dB RL = 10 kΩ, CL = 100 pF, Vout = 0.5 V to VCC - 0.5 V 1.1 V/μs Bandwidth: f = 0.1 to 10 Hz 15 µVpp 55 29 nV -----------Hz 0.002 % Equivalent input noise voltage f = 1 kHz density f = 10 kHz Total harmonic distortion + noise 730 Follower configuration, fin = 1 kHz, RL = 100 kΩ, Vicm = (VCC - 1.5 V)/2, BW = 22 kHz, Vout = 2 Vpp 1. See Section 4.3: Input offset voltage drift over temperature on page 15. 2. Typical value is based on the Vio drift observed after 1000h at 125 °C extrapolated to 25 °C using the Arrhenius law and assuming an activation energy of 0.7 eV. The operational amplifier is aged in follower mode configuration. 3. Guaranteed by design. 8/27 DocID023274 Rev 3 TSX56x, TSX56xA Electrical characteristics Table 6. Electrical characteristics at VCC+ = +16 V with VCC- = 0 V, Vicm = VCC/2, Tamb = 25 °C, and RL = 10 kΩ connected to VCC/2 (unless otherwise specified) Symbol Parameter Conditions Min. Typ. Max. Unit DC performance Vio Offset voltage TSX56xA, T = 25 °C 600 TSX56xA, -40 °C < T < 125 °C 1800 TSX56x, T = 25 °C 1 TSX56x, -40 °C < T < 125 °C ΔVio/ΔT Input offset voltage drift 2.2 -40 °C < T < 125 °C(1) 2 12 T = 25 °C(2) Iio Input offset current (Vout = VCC/2) T = 25 °C 1 100(3) -40 °C < T < 125 °C 1 200(3) Iib Input bias current (Vout = VCC/2) T = 25 °C 1 100(3) -40 °C < T < 125 °C 1 200(3) 76 -40 °C < T < 125 °C 72 CMR1 T = 25 °C 60 CMR2 Common mode rejection ratio CMR = 20 log (ΔVic/ΔVio) (Vic = -0.1 V to VCC + 0.1 V, Vout = VCC/2, RL > 1 MΩ) -40 °C < T < 125 °C 56 T = 25 °C 76 SVR Common mode rejection ratio 20 log (ΔVCC/ΔVio) (VCC = 3 V to 16 V, Vout = Vicm = VCC/2) -40 °C < T < 125 °C 72 Large signal voltage gain (Vout = 0.5 V to (VCC - 0.5 V), RL > 1 MΩ) T = 25 °C 85 Avd -40 °C < T < 125 °C 83 VOH High level output voltage (VOH = VCC - Vout) RL = 10 kΩ, T = 25 °C RL = 10 kΩ, -40 °C < T < 125 °C 70 100 Low level output voltage RL = 10 kΩ, T = 25 °C RL = 10 kΩ, -40 °C < T < 125 °C 70 100 Isink Iout Isource ICC Supply current (per channel, Vout = VCC/2, RL > 1 MΩ) pA 95 Common mode rejection ratio CMR = 20 log (ΔVic/ΔVio) (Vic = -0.1 V to VCC - 1.5 V, Vout = VCC/2, RL > 1 MΩ) VOL μV/°C --------------------------- 1.6 T = 25 °C mV μV month Long-term input offset voltage drift ΔVio μV 78 dB Vout = VCC, T = 25 °C 40 Vout = VCC, -40 °C < T < 125 °C 35 Vout = 0 V, T = 25 °C 30 Vout = 0 V, -40 °C < T < 125 °C 25 T = 25 °C -40 °C < T < 125 °C DocID023274 Rev 3 90 mV 92 mA 90 250 360 400 µA 9/27 Electrical characteristics TSX56x, TSX56xA Table 6. Electrical characteristics at VCC+ = +16 V with VCC- = 0 V, Vicm = VCC/2, Tamb = 25 °C, and RL = 10 kΩ connected to VCC/2 (unless otherwise specified) (continued) Symbol Parameter Conditions Min. Typ. 750 900 Max. Unit AC performance GBP Gain bandwidth product Fu Unity gain frequency Φm Phase margin Gm Gain margin SR Slew rate ∫ en Low-frequency peak-to-peak input noise en THD+N RL = 10 kΩ, CL = 100 pF kHz 55 Degree 9 dB RL = 10 kΩ, CL = 100 pF, Vout = 0.5 V to VCC - 0.5 V 1.1 V/μs Bandwidth: f = 0.1 to 10 Hz 15 µVpp 48 27 nV -----------Hz 0.0005 % Equivalent input noise voltage f = 1 kHz density f = 10 kHz Total harmonic distortion + noise 750 Follower configuration, fin = 1 kHz, RL = 100 kΩ, Vicm = (VCC - 1.5 V)/2, BW = 22 kHz, Vout = 5 Vpp 1. See Section 4.3: Input offset voltage drift over temperature on page 15. 2. Typical value is based on the Vio drift observed after 1000h at 125 °C extrapolated to 25 °C using the Arrhenius law and assuming an activation energy of 0.7 eV. The operational amplifier is aged in follower mode configuration. 3. Guaranteed by design. 10/27 DocID023274 Rev 3 TSX56x, TSX56xA Electrical characteristics Figure 3. Input offset voltage distribution at VCC = 16 V and Vicm = 8 V Figure 2. Supply current vs. supply voltage at Vicm = VCC/2 Figure 4. Input offset voltage temperature Figure 5. Input offset voltage vs. input common coefficient distribution at VCC = 16 V, Vicm = 8 V mode voltage at VCC = 12 V Figure 6. Input offset voltage vs. temperature at VCC = 16 V /LPLWIRU76;[$ /LPLWIRU76;[ 9&& 99LFP 9 $0 DocID023274 Rev 3 11/27 Electrical characteristics TSX56x, TSX56xA Figure 7. Output current vs. output voltage at VCC = 3.3 V Figure 8. Output current vs. output voltage at VCC = 5 V Figure 9. Output current vs. output voltage at VCC = 16 V Figure 10. Bode diagram at VCC = 3.3 V Figure 11. Bode diagram at VCC = 5 V Figure 12. Bode diagram at VCC = 16 V 12/27 DocID023274 Rev 3 TSX56x, TSX56xA Electrical characteristics Figure 13. Phase margin vs. capacitive load at VCC = 12 V Figure 14. GBP vs. input common mode voltage at VCC = 12 V Figure 15. Avd vs. input common mode voltage at VCC = 12 V Figure 16. Slew rate vs. supply voltage Figure 17. Noise vs. frequency at VCC = 3.3 V Figure 18. Noise vs. frequency at VCC = 5 V DocID023274 Rev 3 13/27 Electrical characteristics TSX56x, TSX56xA Figure 19. Noise vs. frequency at VCC = 16 V Figure 20. Distortion + noise vs. output voltage amplitude Figure 21. Distortion + noise vs. amplitude at Vicm = VCC/2 and VCC = 12 V Figure 22. Distortion + noise vs. frequency 14/27 DocID023274 Rev 3 TSX56x, TSX56xA Application information 4 Application information 4.1 Operating voltages The amplifiers of the TSX56x and TSX56xA series can operate from 3 V to 16 V. Their parameters are fully specified at 3.3 V, 5 V and 16 V power supplies. However, the parameters are very stable in the full VCC range. Additionally, the main specifications are guaranteed in extended temperature ranges from -40 to +125 ° C. 4.2 Rail-to-rail input The TSX56x and TSX56xA devices are built with two complementary PMOS and NMOS input differential pairs. The devices have a rail-to-rail input, and the input common mode range is extended from VCC- - 0.1 V to VCC+ + 0.1 V. However, the performance of these devices is clearly optimized for the PMOS differential pairs (which means from VCC- - 0.1 V to VCC+ - 1.5 V). Beyond VCC+ - 1.5 V, the operational amplifiers are still functional but with degraded performance, as can be observed in the electrical characteristics section of this datasheet (mainly Vio and GBP). These performances are suitable for a number of applications needing to be rail-to-rail. The devices are designed to prevent phase reversal. 4.3 Input offset voltage drift over temperature The maximum input voltage drift over the temperature variation is defined as the offset variation related to the offset value measured at 25 °C. The operational amplifier is one of the main circuits of the signal conditioning chain, and the amplifier input offset is a major contributor to the chain accuracy. The signal chain accuracy at 25 °C can be compensated during production at application level. The maximum input voltage drift over temperature enables the system designer to anticipate the effects of temperature variations. The maximum input voltage drift over temperature is computed in Equation 1. Equation 1 ΔV io V io ( T ) – V io ( 25° C ) ------------ = max -------------------------------------------------ΔT T – 25° C with T = -40 °C and 125 °C. The datasheet maximum value is guaranteed by measurement on a representative sample size ensuring a Cpk (process capability index) greater than 2. DocID023274 Rev 3 15/27 Application information 4.4 TSX56x, TSX56xA Long term input offset voltage drift To evaluate product reliability, two types of stress acceleration are used: • Voltage acceleration, by changing the applied voltage • Temperature acceleration, by changing the die temperature (below the maximum junction temperature allowed by the technology) with the ambient temperature. The voltage acceleration has been defined based on JEDEC results, and is defined using Equation 2. Equation 2 A FV = e β ⋅ ( VS – VU ) Where: AFV is the voltage acceleration factor β is the voltage acceleration constant in 1/V, constant technology parameter (β = 1) VS is the stress voltage used for the accelerated test VU is the voltage used for the application The temperature acceleration is driven by the Arrhenius model, and is defined in Equation 3. Equation 3 A FT = e Ea ⎛ 1 1 ------ ⋅ ------ – ------⎞ ⎝ T U T S⎠ k Where: AFT is the temperature acceleration factor Ea is the activation energy of the technology based on the failure rate k is the Boltzmann constant (8.6173 x 10-5 eV.K-1) TU is the temperature of the die when VU is used (K) TS is the temperature of the die under temperature stress (K) The final acceleration factor, AF, is the multiplication of the voltage acceleration factor and the temperature acceleration factor (Equation 4). Equation 4 A F = A FT × A FV AF is calculated using the temperature and voltage defined in the mission profile of the product. The AF value can then be used in Equation 5 to calculate the number of months of use equivalent to 1000 hours of reliable stress duration. 16/27 DocID023274 Rev 3 TSX56x, TSX56xA Application information Equation 5 Months = A F × 1000 h × 12 months ⁄ ( 24 h × 365.25 days ) To evaluate the op-amp reliability, a follower stress condition is used where VCC is defined as a function of the maximum operating voltage and the absolute maximum rating (as recommended by JEDEC rules). The Vio drift (in µV) of the product after 1000 h of stress is tracked with parameters at different measurement conditions (see Equation 6). Equation 6 V CC = maxV op with V icm = V CC ⁄ 2 The long term drift parameter (ΔVio), estimating the reliability performance of the product, is obtained using the ratio of the Vio (input offset voltage value) drift over the square root of the calculated number of months (Equation 7). Equation 7 V io drift ΔV io = -----------------------------( months ) where Vio drift is the measured drift value in the specified test conditions after 1000 h stress duration. 4.5 PCB layouts For correct operation, it is advised to add 10 nF decoupling capacitors as close as possible to the power supply pins. 4.6 Macromodel Accurate macromodels of the TSX56x, TSX56xA devices are available on the STMicroelectronics’ website at www.st.com. These models are a trade-off between accuracy and complexity (that is, time simulation) of the TSX56x and TSX56xA operational amplifiers. They emulate the nominal performance of a typical device within the specified operating conditions mentioned in the datasheet. They also help to validate a design approach and to select the right operational amplifier, but they do not replace on-board measurements. DocID023274 Rev 3 17/27 Package information 5 TSX56x, TSX56xA Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: www.st.com. ECOPACK is an ST trademark. 18/27 DocID023274 Rev 3 TSX56x, TSX56xA 5.1 Package information SOT23-5 package information Figure 23. SOT23-5 package mechanical drawing Table 7. SOT23-5 package mechanical data Dimensions Ref. A Millimeters Inches Min. Typ. Max. Min. Typ. Max. 0.90 1.20 1.45 0.035 0.047 0.057 A1 0.15 0.006 A2 0.90 1.05 1.30 0.035 0.041 0.051 B 0.35 0.40 0.50 0.013 0.015 0.019 C 0.09 0.15 0.20 0.003 0.006 0.008 D 2.80 2.90 3.00 0.110 0.114 0.118 D1 1.90 0.075 e 0.95 0.037 E 2.60 2.80 3.00 0.102 0.110 0.118 F 1.50 1.60 1.75 0.059 0.063 0.069 L 0.10 0.35 0.60 0.004 0.013 0.023 K 0° 10 ° 0° DocID023274 Rev 3 10 ° 19/27 Package information 5.2 TSX56x, TSX56xA DFN8 2x2 package information Figure 24. DFN8 2x2 package mechanical drawing ' $ % & [ ( 3,1,1'(;$5($ & [ 7239,(: $ $ & & 6($7,1* 3/$1( 6,'(9,(: & H ESOFV 3,1,1'(;$5($ & $ % / 3LQ,' %277209,(: *$06&% Table 8. DFN8 2x2 package mechanical data Dimensions Ref. Inches Min. Typ. Max. Min. Typ. Max. A 0.70 0.75 0.80 0.028 0.030 0.031 A1 0.00 0.02 0.05 0.000 0.001 0.002 b 0.15 0.20 0.25 0.006 0.008 0.010 D 2.00 0.079 E 2.00 0.079 e 0.50 0.020 L N 20/27 Millimeters 0.045 0.55 0.65 8 DocID023274 Rev 3 0.018 0.022 8 0.026 TSX56x, TSX56xA 5.3 Package information MiniSO8 package information Figure 25. MiniSO8 package mechanical drawing Table 9. MiniSO8 package mechanical data Dimensions Symbol Millimeters Min. Typ. A Inches Max. Min. Typ. 1.10 A1 0 A2 0.75 b Max. 0.043 0.15 0 0.95 0.030 0.22 0.40 0.009 0.016 c 0.08 0.23 0.003 0.009 D 2.80 3.00 3.20 0.11 0.118 0.126 E 4.65 4.90 5.15 0.183 0.193 0.203 E1 2.80 3.00 3.10 0.11 0.118 0.122 e L 0.85 0.65 0.40 0.60 0.006 0.033 0.026 0.80 0.016 0.024 L1 0.95 0.037 L2 0.25 0.010 k ccc 0° 0.037 8° 0.10 DocID023274 Rev 3 0° 0.031 8° 0.004 21/27 Package information 5.4 TSX56x, TSX56xA QFN16 3x3 package information Figure 26. QFN16 3x3 package mechanical drawing ' $ % DDD & [ ( ,1'(;$5($ '[( DDD & [ 7239,(: $ FFF & $ & 6($7,1* 3/$1( 6,'(9,(: HHH & H / E EEE EEE 3LQ,' 5 & $ % & %277209,(: *$06&% 22/27 DocID023274 Rev 3 TSX56x, TSX56xA Package information Table 10. QFN16 3x3 package mechanical data Dimensions Ref. Millimeters Min. Typ. Inches Max. Min. Typ. Max. A 0.50 0.65 0.020 0.026 A1 0 0.05 0 0.002 b 0.18 0.30 0.007 0.25 0.010 D 3.00 0.118 E 3.00 0.118 e 0.50 0.020 L 0.30 0.50 0.012 0.012 0.020 aaa 0.15 0.006 bbb 0.10 0.004 ccc 0.10 0.004 ddd 0.05 0.002 eee 0.08 0.003 DocID023274 Rev 3 23/27 Package information 5.5 TSX56x, TSX56xA TSSOP14 package information Figure 27. TSSOP14 package mechanical drawing Table 11. TSSOP14 package mechanical data Dimensions Symbol Millimeters Min. Typ. A Max. Min. Typ. 1.20 A1 0.05 A2 0.80 b Max. 0.047 0.15 0.002 0.004 0.006 1.05 0.031 0.039 0.041 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0089 D 4.90 5.00 5.10 0.193 0.197 0.201 E 6.20 6.40 6.60 0.244 0.252 0.260 E1 4.30 4.40 4.50 0.169 0.173 0.176 e L k aaa 1.00 0.65 0.45 L1 24/27 Inches 0.60 0.0256 BSC 0.75 1.00 0° 8° 0° 0.10 0.018 DocID023274 Rev 3 8° 0.024 0.030 TSX56x, TSX56xA 6 Ordering information Ordering information Table 12. Order codes Channel number Package TSX561ILT 1 SOT23-5 TSX562IQ2T 2 DFN8 2 x 2 2 MiniSO8 TSX564IQ4T 4 QFN16 3 x 3 TSX564IPT 4 TSSOP14 1 SOT23-5 2 MiniSO8 TSX564IYPT 4 TSSOP14 TSX561AILT 1 SOT23-5 2 MiniSO8 4 TSSOP14 1 SOT23-5 2 MiniSO8 4 TSSOP14 Order code TSX562IST Temperature range -40 to 125 °C TSX561IYLT TSX562IYST TSX562AIST -40 to 125 °C automotive grade(1) -40 to 125 °C TSX564AIPT TSX561AIYLT TSX562AIYST TSX564AIYPT -40 to 125 °C automotive grade(1) Packaging Marking K23 TSX564I K116 Tape and reel TSX564IY K117 TSX564AI K118 TSX564AIY 1. Qualification and characterization according to AEC Q100 and Q003 or equivalent, advanced screening according to AEC Q001 and Q 002 or equivalent are ongoing. DocID023274 Rev 3 25/27 Revision history 7 TSX56x, TSX56xA Revision history Table 13. Document revision history Date Revision 06-Jun-2012 1 Initial release. 2 Added TSX562, TSX564, TSX562A, and TSX564A devices. Updated Features, Description, Figure 1, Table 1 (added DFN8, MiniSO8, QFN16, and TSSOP14 package). Updated Table 1 (updated ESD MM values). Updated Table 4 and Table 5 (added footnotes), Section 5 (added Figure 24 to Figure 27 and Table 8 to Table 11), Table 12 (added dual and quad devices). Minor corrections throughout document. 3 Replaced the silhouette, pinout, package diagram, and mechanical data of the DFN8 2x2 and QFN16 3x3 packages. Added Benefits and Related products. Table 1: updated Rthja values and added Rthjc values for DFN8 2x2 and QFN16 3x3. Updated Section 4.3, Section 4.4, and Section 4.6 Replaced Figure 23: SOT23-5 package mechanical drawing and Table 7: SOT23-5 package mechanical data. 18-Sep-2012 23-May-2013 26/27 Changes DocID023274 Rev 3 TSX56x, TSX56xA Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. ST PRODUCTS ARE NOT AUTHORIZED FOR USE IN WEAPONS. NOR ARE ST PRODUCTS DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B) AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2013 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com DocID023274 Rev 3 27/27