SN74LV393A-Q1 DUAL 4-BIT BINARY COUNTER SCLS515C − JULY 2003 − REVISED FEBRUARY 2008 D Qualified for Automotive Applications D ESD Protection Exceeds 2000 V Per D D D D D D D D PW PACKAGE (TOP VIEW) MIL-STD-883, Method 3015; Exceeds 200 V Using Machine Model (C = 200 pF, R = 0) 2-V to 5.5-V VCC Operation Max tpd of 9.5 ns at 5 V Typical VOLP (Output Ground Bounce) <0.8 V at VCC = 3.3 V, TA = 25°C Typical VOHV (Output VOH Undershoot) >2.3 V at VCC = 3.3 V, TA = 25°C Ioff Supports Partial-Power-Down-Mode Operation Dual 4-Bit Binary Counters With Individual Clocks Direct Clear for Each 4-Bit Counter Can Significantly Improve System Densities by Reducing Counter Package Count by 50 Percent 1CLK 1CLR 1QA 1QB 1QC 1QD GND 1 14 2 13 3 12 4 11 5 10 6 9 7 8 VCC 2CLK 2CLR 2QA 2QB 2QC 2QD description/ordering information The SN74LV393A contains eight flip-flops and additional gating to implement two individual 4-bit counters in a single package. This device is designed for 2-V to 5.5-V VCC operation. This device comprises two independent 4-bit binary counters, each having a clear (CLR) and a clock (CLK) input. The device changes state on the negative-going transition of the CLK pulse. N-bit binary counters can be implemented with each package, providing the capability of divide by 256. The SN74LV393A has parallel outputs from each counter stage so that any submultiple of the input count frequency is available for system timing signals. This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down. ORDERING INFORMATION† −40°C to 105°C ORDERABLE PART NUMBER PACKAGE‡ TA TSSOP − PW Tape and reel TOP-SIDE MARKING SN74LV393ATPWRQ1 LV393AT † For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI web site at http://www.ti.com. ‡ Package drawings, thermal data, and symbolization are available at http://www.ti.com/packaging. FUNCTION TABLE INPUTS FUNCTION CLK CLR ↑ L No change ↓ L Advance to next stage X H All outputs L Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2008, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SN74LV393A-Q1 DUAL 4-BIT BINARY COUNTER SCLS515C − JULY 2003 − REVISED FEBRUARY 2008 logic diagram, each counter (positive logic) R CLR CLK Q QA Q QB Q QC Q QD T R T R T R T timing diagram CLK CLR QA QB Outputs QC QD Count Up Clear 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN74LV393A-Q1 DUAL 4-BIT BINARY COUNTER SCLS515C − JULY 2003 − REVISED FEBRUARY 2008 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V Output voltage range applied in high or low state, VO (see Notes 1 and 2) . . . . . . . . . . −0.5 V to VCC + 0.5 V Output voltage range applied in power-off state, VO (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −20 mA Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −50 mA Continuous output current, IO (VO = 0 to VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±25 mA Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA Package thermal impedance, θJA (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output current ratings are observed. 2. This value is limited to 7 V maximum. 3. The package thermal impedance is calculated in accordance with JESD 51-7. recommended operating conditions (see Note 4) VCC Supply voltage VCC = 2 V VIH High level input voltage High-level MIN MAX 2 5.5 Low level input voltage Low-level VI Input voltage VO Output voltage VCC = 2.3 V to 2.7 V VCC × 0.7 VCC = 3 V to 3.6 V VCC × 0.7 VCC = 4.5 V to 5.5 V VCC × 0.7 0.5 VCC × 0.3 VCC = 3 V to 3.6 V VCC × 0.3 VCC × 0.3 5.5 0 VCC V −50 µA VCC = 2.3 V to 2.7 V VCC = 3 V to 3.6 V −6 ∆t/∆v Input transition rise or fall rate 50 VCC = 2.3 V to 2.7 V 2 VCC = 3 V to 3.6 V 6 VCC = 4.5 V to 5.5 V 12 VCC = 2.3 V to 2.7 V 200 VCC = 3 V to 3.6 V 100 VCC = 4.5 V to 5.5 V TA Operating free-air temperature mA −12 VCC = 2 V Low level output current Low-level V −2 VCC = 4.5 V to 5.5 V IOL V 0 VCC = 2 V High level output current High-level V VCC = 2.3 V to 2.7 V VCC = 4.5 V to 5.5 V IOH V 1.5 VCC = 2 V VIL UNIT µA mA ns/V 20 −40 105 °C NOTE 4: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 SN74LV393A-Q1 DUAL 4-BIT BINARY COUNTER SCLS515C − JULY 2003 − REVISED FEBRUARY 2008 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VOH TEST CONDITIONS VCC MIN IOH = −50 µA 2 V to 5.5 V VCC−0.1 IOH = −2 mA 2.3 V 2 IOH = −6 mA 3V 2.48 4.5 V 3.8 IOH = −12 mA VOL TYP MAX V IOL = 50 µA 2 V to 5.5 V 0.1 IOL = 2 mA 2.3 V 0.4 IOL = 6 mA 3V 0.44 4.5 V 0.55 IOL = 12 mA II VI = 5.5 V or GND ICC VI = VCC or GND, Ioff VI or VO = 0 to 5.5 V Ci VI = VCC or GND IO = 0 UNIT V 0 to 5.5 V ±1 µA 5.5 V 20 µA 0 5 µA 3.3 V 1.8 pF timing requirements over recommended operating free-air temperature range, VCC = 2.5 V ± 0.2 V (unless otherwise noted) (see Figure 1) TA = 25°C MIN tw Pulse duration tsu Setup time MAX MIN CLK high or low 5 5 CLR high 5 5 CLR inactive before CLK↓ 6 6 MAX UNIT ns ns timing requirements over recommended operating free-air temperature range, VCC = 3.3 V ± 0.3 V (unless otherwise noted) (see Figure 1) TA = 25°C MIN tw Pulse duration tsu Setup time MAX MIN CLK high or low 5 5 CLR high 5 5 CLR inactive before CLK↓ 5 5 MAX UNIT ns ns timing requirements over recommended operating free-air temperature range, VCC = 5 V ± 0.5 V (unless otherwise noted) (see Figure 1) TA = 25°C MIN 4 tw Pulse duration tsu Setup time POST OFFICE BOX 655303 MAX MIN CLK high or low 5 5 CLR high 5 5 CLR inactive before CLK↓ 4 4 • DALLAS, TEXAS 75265 MAX UNIT ns ns SN74LV393A-Q1 DUAL 4-BIT BINARY COUNTER SCLS515C − JULY 2003 − REVISED FEBRUARY 2008 switching characteristics over recommended operating VCC = 2.5 V ± 0.2 V (unless otherwise noted) (see Figure 1) PARAMETER FROM (INPUT) TO (OUTPUT) fmax tpd tPHL LOAD CAPACITANCE CLR FROM (INPUT) 30 tPHL CLR FROM (INPUT) tPHL CLR 25 MHz QB 10.9 23.9 1 27.5 12.3 26.1 1 30 QD 13.4 27.8 1 32 Qn 9.1 17.4 1 20 QC CL = 50 pF p TO (OUTPUT) LOAD CAPACITANCE free-air range, MIN UNIT TA = 25°C MIN TYP 45 105 MAX MAX 35 MHz 6.7 16.7 1 19 QB 7.8 19.3 1 22 CL = 50 pF p 8.7 21.5 1 24.5 QD 9.5 23.2 1 26.5 Qn 6.8 15.8 1 18 QC TO (OUTPUT) LOAD CAPACITANCE free-air TYP 85 150 range, MIN UNIT MAX MAX 75 MHz QA 4.9 10.5 1 12 QB 5.6 11.8 1 13.5 6.2 13.2 1 15 QD 6.6 14.5 1 16.5 Qn 5.2 10.1 1 11.5 QC POST OFFICE BOX 655303 CL = 50 pF p • DALLAS, TEXAS 75265 ns temperature TA = 25°C MIN ns temperature QA CL = 50 pF CLK 70 24.5 fmax tpd UNIT MAX 1 switching characteristics over recommended operating VCC = 5 V ± 0.5 V (unless otherwise noted) (see Figure 1) PARAMETER MIN MAX 21.3 CL = 50 pF CLK TYP 9.3 fmax tpd range, QA switching characteristics over recommended operation VCC = 3.3 V ± 0.3 V (unless otherwise noted) (see Figure 1) PARAMETER temperature TA = 25°C MIN CL = 50 pF CLK free-air ns 5 SN74LV393A-Q1 DUAL 4-BIT BINARY COUNTER SCLS515C − JULY 2003 − REVISED FEBRUARY 2008 noise characteristics, VCC = 3.3 V, CL = 50 pF, TA = 25°C (see Note 5) TYP MAX VOL(P) Quiet output, maximum dynamic VOL PARAMETER MIN 0.3 0.8 UNIT V VOL(V) Quiet output, minimum dynamic VOL −0.2 −0.8 V VOH(V) Quiet output, minimum dynamic VOH 2.8 VIH(D) High-level dynamic input voltage VIL(D) Low-level dynamic input voltage V 2.31 V 0.99 V UNIT NOTE 5: Characteristics are for surface-mount packages only. operating characteristics, TA = 25°C PARAMETER Cpd 6 Power dissipation capacitance TEST CONDITIONS CL = 50 pF, pF POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 f = 10 MHz VCC TYP 3.3 V 15.2 5V 17.3 pF SN74LV393A-Q1 DUAL 4-BIT BINARY COUNTER SCLS515C − JULY 2003 − REVISED FEBRUARY 2008 PARAMETER MEASUREMENT INFORMATION VCC From Output Under Test Test Point RL = 1 kΩ From Output Under Test CL (see Note A) S1 Open TEST GND S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open Drain CL (see Note A) Open VCC GND VCC LOAD CIRCUIT FOR 3-STATE AND OPEN-DRAIN OUTPUTS LOAD CIRCUIT FOR TOTEM-POLE OUTPUTS VCC 50% VCC Timing Input 0V tw tsu VCC 50% VCC 50% VCC Input th VCC 50% VCC Data Input 50% VCC 0V 0V VOLTAGE WAVEFORMS PULSE DURATION VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VCC 50% VCC Input 50% VCC tPLH tPHL 50% VCC tPHL 50% VCC VOL VOH 50% VCC VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS 50% VCC 0V Output Waveform 1 S1 at VCC (see Note B) tPLZ ≈VCC 50% VCC tPZH tPLH 50% VCC 50% VCC tPZL VOH In-Phase Output Out-of-Phase Output 0V VCC Output Control Output Waveform 2 S1 at GND (see Note B) VOL + 0.3 V VOL tPHZ 50% VCC VOH − 0.3 V VOH ≈0 V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 1 MHz, ZO = 50 Ω, tr ≤ 3 ns, tf ≤ 3 ns. D. The outputs are measured one at a time, with one input transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPHL and tPLH are the same as tpd. H. All parameters and waveforms are not applicable to all devices. Figure 1. Load Circuit and Voltage Waveforms POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7 PACKAGE OPTION ADDENDUM www.ti.com 12-Oct-2011 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp SN74LV393ATPWRG4Q1 ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LV393ATPWRQ1 ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM (3) Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF SN74LV393A-Q1 : • Catalog: SN74LV393A • Enhanced Product: SN74LV393A-EP Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 12-Oct-2011 NOTE: Qualified Version Definitions: • Catalog - TI's standard catalog product • Enhanced Product - Supports Defense, Aerospace and Medical Applications Addendum-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP® Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2011, Texas Instruments Incorporated