TXS02324 SCES823 – FEBRUARY 2011 www.ti.com Dual-Supply 2:1 SIM Card Multiplexer/Translator With Slot Dedicated Dual LDO Check for Samples: TXS02324 FEATURES 1 • IRQ SDA SCL VDDIO SIMIO 14 12 13 11 10 17 9 SIMCLK SIMRST GND 18 8 SIM1CLK SIM2CLK 19 7 SIM2IO 20 6 SIM1IO SIM1RST 1 2 3 4 5 GND VSIM1 • RSTX DNU 15 16 VBAT • RUK PACKAGE (TOP VIEW) VSIM2 • Level Translator – VDDIO Range of 1.7 V to 3.3 V Low-Dropout (LDO) Regulator – 50-mA LDO Regulator With Enable – 1.8-V or 2.95-V Selectable Output Voltage – 2.3-V to 5.5-V Input Voltage Range – Very Low Dropout: 100 mV (Max) at 50 mA Control and Communication Through I2C Interface With Baseband Processor ESD Protection Exceeds JESD 22 – 2000-V Human-Body Model (A114-B) – 1000-V Charged-Device Model (C101) Package – 20-Pin QFN (3 mm x 3 mm) SIM2RST • Note: The Exposed Thermal Pad must be connect to Ground. DESCRIPTION/ORDERING INFORMATION The TXS02324 is a complete dual-supply standby Smart Identity Module (SIM) card solution for interfacing wireless baseband processors with two individual SIM subscriber cards to store data for mobile handset applications. It is a custom device which is used to extend a single SIM/UICC interface to be able to support two SIMs/UICCs. The device complies with ISO/IEC Smart-Card Interface requirements as well as GSM and 3G mobile standards. It includes a high-speed level translator capable of supporting Class-B (2.95 V) and Class-C (1.8 V) interfaces, two low-dropout (LDO) voltage regulators that have output voltages that are selectable between 2.95-V Class-B and 1.8-V Class-C interfaces, an integrated "fast-mode" 400 kb/s "slave" I2C control register interface for configuration purposes, a 32-kHz clock input for internal timing generation. The voltage-level translator has two supply voltage pins. VDDIO sets the reference for the baseband interface and can be operated from 1.7 V to 3.3 V. VSIM1 and VSIM2 are programmed to either 1.8 V or 2.95 V, each supplied by an independent internal LDO regulator. The integrated LDO accepts input battery voltages from 2.3 V to 5.5 V and outputs up to 50 mA to the B-side circuitry and external Class-B or Class-C SIM card. ORDERING INFORMATION (1) PACKAGE (2) TA –40°C to 85°C (1) (2) QFN – RUK ORDERABLE PART NUMBER Tape and reel TXS02324RUKR TOP-SIDE MARKING ZUY For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI web site at www.ti.com. Package drawings, thermal data, and symbolization are available at www.ti.com/packaging. 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. © 2011, Texas Instruments Incorporated TXS02324 SCES823 – FEBRUARY 2011 www.ti.com VBAT SCK SDA 2 IC Control Logic LDO VSIM1 SIM1_RST SIM_RST SIM1_CLK SIM_CLK Translator VCC GND Reset VPP CLK I/O NC NC SIM1_I/O SIM_I/O Baseband 3-V or 1.8-V SIM Card V_I/O VCC RSTX LDO IRQ VSIM2 SIM2_RST 3-V or 1.8-V SIM Card VCC GND Reset VPP CLK I/O NC NC SIM2_CLK Translator SIM2_I/O GND TXS02324 Figure 1. Interfacing With SIM Card 2 Submit Documentation Feedback © 2011, Texas Instruments Incorporated Product Folder Link(s): TXS02324 TXS02324 SCES823 – FEBRUARY 2011 www.ti.com TERMINAL FUNCTIONS (1) NO. NAME TYPE (1) POWER DOMAIN 1 SIM2RST O VSIM2 SIM2 reset 2 VSIM2 O VSIM2 1.8 V/2.95 V supply voltage to SIM2 3 VBAT P VBAT Battery power supply 4 GND G 5 VSIM1 O VSIM1 1.8 V/2.95 V supply voltage to SIM1 6 SIM1RST O VSIM1 SIM1 reset 7 SIM1IO I/O VSIM1 SIM1 data 8 SIM1CLK O VSIM1 SIM1 clock 9 SIMRST I VDDIO UICC/SIM reset from baseband 10 SIMCLK I VDDIO UICC/SIM clock 11 SIMIO I/O VDDIO UICC/SIM data 12 VDDIO P VDDIO 1.8-V power supply for device operation and I/O buffers toward baseband 13 SCL I VDDIO I2C clock 14 SDA I/O VDDIO I2C data 15 IRQ I/O VDDIO Interrupt to baseband. This signal is used to set the I2C address. 16 RSTX I VDDIO Active-low reset input from baseband Do not use. Should not be electrically connected. DESCRIPTION Ground 17 DNU I VDDIO 18 GND G - GROUND 19 SIM2CLK O VSIM2 SIM2 clock 20 SIM2IO I/O VSIM2 SIM2 data G = Ground, I = Input, O = Output, P = Power Submit Documentation Feedback © 2011, Texas Instruments Incorporated Product Folder Link(s): TXS02324 3 TXS02324 SCES823 – FEBRUARY 2011 www.ti.com Table 1. Register Overview REGISTER BITS B7 B6 B5 B4 B3 B2 B1 B0 COMMAND BYTE (HEX) 0 0 0 1 0 0 0 1 00h Device hardware revision information R 0001 0001 0 0 0 0 0 0 0 0 01h Software revision information R 0000 0000 Unused Unused Unused Unused 04h Status Register R 0000 0000 SIM1 Voltage Select SIM1 LDO Enable/ Disable 08h SIM Interface Control Register R/W 0000 0000 SIM2 Interface Status SIM2 Interface Status 4 SIM1 Interface Status SIM2 Voltage Select SIM2 LDO Enable/ Disable SIM1 Interface Status Submit Documentation Feedback REGISTER READ OR WRITE POWER-UP DEFAULT © 2011, Texas Instruments Incorporated Product Folder Link(s): TXS02324 TXS02324 SCES823 – FEBRUARY 2011 www.ti.com Table 2. Device Hardware Revision Register (00h) Device HW Driver Register HW identification (1) Bits(s) Type (R/W) 7:0 R Description This register contains the manufacturer and device ID (1) (value to be specified by the manufacturer) The manufacturer ID part of this data shall remain unchanged when the HW revision ID is updated. The manufacturer ID shall uniquely identify the manufacturer. The manufacturer ID is encoded on the MSB nibble. Table 3. Device Software Revision Register (01h) Device SW Driver Register SW Driver Version Bits(s) 7:0 Type (R/W) R Description This register contains information about the SW driver required for this device. This information shall only be updated when changes to the device requires SW modifications. Initial register value is 00h Table 4. Status Register (04h) Bits(s) Type (R/W) Unused Status Register 0 Unused Unused Unused 1 Unused Unused Unused 2 Unused Unused Unused 3 Unused Unused SIM1 Interface Status [1:0] SIM2 Interface Status [1:0] (1) 5:4 (1) 7:6 (1) Description R Status of SIM1 interface '00' Powered down with pull-downs activated '01' Isolated with pull-downs deactivated '10' Powered with pull downs activated '11' Active with pull downs deactivated R Status of SIM2 interface '00' Powered down with pull-downs activated '01' Isolated with pull-downs deactivated '10' Powered with pull downs activated '11' Active with pull downs deactivated The content of bits 5:4 and 7:6 reflects the value written to the state bits in the SIM Interface control register 3:2 and 7:6 respectively and the setting of the regulator bits in the SIM interface control register 0 and 4 respectively. Table 5. SIM Interface Control Register (08h) (1) (2) Status Register Bit(s) Type (R/W) SIM1 Regulator Control 0 R/W '0' Regulator is off, regulator output is pulled down '1' Regulator is powered on, regulator output pull-down is released SIM1 Regulator Voltage Selection 1 R/W '0' 1.8 V '1' 2.95 V R/W Status of SIM1 interface '00' Powered down state with pull-downs activated '01' Isolated state with pull-downs deactivated '10' Not allowed '11' Active state with pull downs deactivated R/W '0' Regulator is off, regulator output is pulled down '1' Regulator is powered on, regulator output pull-down is released SIM1 Interface State [1:0] SIM2 Regulator Control (1) (2) 3:2 4 Description Reset value: 00h The state '10', on bits 3:2 and 7:6, is not prevented by HW but shall never be set by SW. State '10' means that the interface is powered with the pull-downs active, this state correspond to state '00' with the regulator being switched on. Setting the state to '10' does not have any impact on the corresponding regulator bit setting. The regulator control bits do not impact the state bits in this register. The regulator control bits however do impact the status bits in the status register. Submit Documentation Feedback © 2011, Texas Instruments Incorporated Product Folder Link(s): TXS02324 5 TXS02324 SCES823 – FEBRUARY 2011 www.ti.com Table 5. SIM Interface Control Register (08h)(1)(2) (continued) Status Register SIM2 Regulator Voltage SIM2 Interface State [1:0] 6 Bit(s) Type (R/W) 5 R/W '0' 1.8 V '1' 2.95 V R/W Status of SIM2 interface '00' Powered down state with pull-downs activated '01' Isolated state with pull-downs deactivated '10' Not allowed '11' Active state with pull downs deactivated 7:6 Submit Documentation Feedback Description © 2011, Texas Instruments Incorporated Product Folder Link(s): TXS02324 TXS02324 SCES823 – FEBRUARY 2011 www.ti.com BASIC DEVICE OPERATION The TXS02324 is controlled through a standard I2C interface reference to VDDIO. It is connected between the two SIM card slots and the SIM/UICC interface of the baseband. The device uses VBAT and VDDIO as supply voltages. The supply voltage for each SIM card is generated by an on-chip low drop out regulator. The interface between the baseband and the TXS02324 is reference to VDDIO while the interface between the TXS02324 and the SIM card is referenced to the LDO output of either VSIM1 or VSIM2 depending on which slot is being selected. The VDDIO on the baseband side normally does not exceed 1.8V, thus voltage level shifting is needed to support a 3V SIM/UICC interface (Class B). The TXS02324 has two basic states, the reset and operation state. The baseband utilizes information in the status registers to determine how to manipulate the control registers to properly switch between two SIM cards. These fundamental sequences are outlined below and are to help the user to successfully incorporate this device into the system. DEVICE ADDRESS The address of the device is shown below: Slave Address 0 1 1 1 1 0 IRQ R/W Address Reference IRQ@ Reset R/W Slave Address 0 0 (W) 120 (decimal), 78(h) 0 1 (R) 121 (decimal), 79(h) 1 0 (W) 122 (decimal), 7A(h) 1 1 (R) 123 (decimal), 7B(h) RESET STATE In the reset state the device settings are brought back to their default values and any SIM card that has been active is deactivated. After reset, neither of the UICC/SIM interfaces is selected. The active pull-downs at the UICC/SIM interface are automatically activated. To ensure the system powers up in an operational state, device uses an internal 32 KHz clock for internal timing generation. • Power up the TXS02324 by asserting VBAT to enter the operation state • I2C Interface becomes active with the VDDIO supply RESET summary: • Any pending interrupts are cleared • I2C registers are in the default state • Both on chip regulators are set to 1.8V and disabled • All SIM1 and SIM2 signals are pulled to GND Submit Documentation Feedback © 2011, Texas Instruments Incorporated Product Folder Link(s): TXS02324 7 TXS02324 SCES823 – FEBRUARY 2011 www.ti.com SETTING UP THE SIM INTERFACE The TXS02324 supports both Class C (1.8V) or Class B (2.95V) SIM cards. In order to support these cards types, the interface on the SIM side needs to be properly setup. After power up, the system should default to SIM1 card. The following sequence outlines a rudimentary sequence of preparing the SIM1 card interface: • Configure the SIM1 regulator to 1.8V by asserting B1 = 0 in the SIM Interface Control Register (08h). The system by default should start in 1.8V mode. • The baseband SIM interface is set to a LOW state. • Disable the SIM1 interface by asserting B2 = 0 and B3 = 0 in the SIM Interface Control Register. • Disable the SIM2 interface by asserting B6 = 0 and B7 = 0 in the SIM Interface Control Register. • VSIM1 voltage regulator should now be activated by asserting B0 = 1 in the SIM Interface Control Register. • Enable the SIM1 interface by asserting B2 = 1 and B3 = 1 in the SIM Interface Control Register. • The SIM1 interface (VSIM1, SIM1CLK, SIM1I/O) is now active. The TXS02324 relies on the baseband to perform the power up sequencing of the SIM card. If there is lack of communication between the baseband and the SIM card, the SIM1 interface must be powered-down and then powered up again through the regulator by configuring it to 2.95V by asserting B1 = 1 in the SIM Interface Control Register. SWITCHING BETWEEN SIM CARDS The following sequence outlines a rudimentary sequence of switching between the SIM1 card and SIM2 card: • Put the SIM1 card interface into “clock stop” mode then assert B2 = 1 and B3 = 0 in the SIM Interface Control Register (08h). This will latch the state of the SIM1 interface (SIM1CLK, SIM1I/O, SIM1RST). • There can be two scenarios when switching to SIM2 card: – SIM2 may be in the power off mode, B6 = 0 and B7 = 0 in the Status Register (04h). If SIM2 is in power off mode, the SIM/UICC interface will need to be set to the power off state. In this case the baseband will most likely need to go through a power up sequence iteration – SIM2 may already be in the “clock stop” mode, B6 = 1 and B7 = 0 in the Status Register (04h). If SIM2 is in “clock stop” mode, the interface between the baseband and the device is set to the clock stop mode levels that correspond to the SIM2 card interface. • After determining whether the SIM2 card is either in power off mode or clock stop mode, the SIM2 card interface is then activated by asserting B6 = 1 and B7 = 1 in the SIM Interface Control Register (08h) and the negotiation between the baseband and card can continue. • Switching from SIM2 to SIM1 done in the same manner. 8 Submit Documentation Feedback © 2011, Texas Instruments Incorporated Product Folder Link(s): TXS02324 TXS02324 SCES823 – FEBRUARY 2011 www.ti.com ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range (unless otherwise noted) Level Translator (1) VDDIO Supply voltage range VI Input voltage range MIN MAX UNIT –0.3 4.0 V V_I/O-port –0.5 4.6 VSIMx-port –0.5 4.6 Control inputs –0.5 4.6 V_I/O-port –0.5 4.6 VSIMx-port –0.5 4.6 V_I/O-port –0.5 4.6 VSIMx-port –0.5 4.6 V VO Voltage range applied to any output in the high-impedance or power-off state VO Voltage range applied to any output in the high or low state IIK Input clamp current VI < 0 –50 mA IOK Output clamp current VO < 0 –50 mA IO Continuous output current ±50 mA ±100 mA 150 °C Continuous current through VCCA or GND Tstg (1) –65 Storage temperature range V V Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. LDO (1) MIN MAX UNIT VIN Input voltage range –0.3 6 V VOUT Output voltage range –0.3 6 V TJ Junction temperature range –55 150 °C Tstg Storage temperature range –55 150 °C 2 kV 1000 V ESD rating (1) Human-Body Model (HBM) Charged-Device Model (CDM) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. Submit Documentation Feedback © 2011, Texas Instruments Incorporated Product Folder Link(s): TXS02324 9 TXS02324 SCES823 – FEBRUARY 2011 www.ti.com THERMAL IMPEDANCE RATINGS UNIT Package thermal impedance (1) θJA (1) RUK package 94.1 °C/W The package thermal impedance is calculated in accordance with JESD 51-7. RECOMMENDED OPERATING CONDITIONS (1) Level Translator Description VDDIO Supply voltage VIH High-level input voltage VIL Low-level input voltage Δt/Δv Input transition rise or fall rate TA Operating free-air temperature (1) 10 Applies to pins: RSTX, SCL, SDA, IRQ, SIMRST, SIMCLK, SIMIO MIN MAX UNIT 1.7 3.3 V VDDIO × 0.7 1.9 V 0 VDDIO × 0.3 V 5 ns/V 85 °C –40 All unused data inputs of the device must be held at VCCI or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. Submit Documentation Feedback © 2011, Texas Instruments Incorporated Product Folder Link(s): TXS02324 TXS02324 SCES823 – FEBRUARY 2011 www.ti.com ELECTRICAL CHARACTERISTICS Level Translator over recommended operating free-air temperature range (unless otherwise noted) PARAMETER SIM1RST SIM1CLK SIM1IO SIM2RST VOH SIM2CLK VOL Ci VSIM1 VSIM2 IOH = –100 µA Push-Pull TYP ( 1) MAX VSIM1 × 0.8 VSIM1 × 0.8 1.8 V / 2.95 1.7 V to V 3.3 V (Supplied by LDO) 1.8 V / 2.95 V (Supplied by LDO) VSIM2 × 0.8 V VSIM2 × 0.8 VSIM2 × 0.8 SIMIO IOH = –10 µA Open-Drain VDDIO × 0.8 SIM1RST IOL = 1 mA Push-Pull VSIM1 × 0.2 SIM1CLK IOL = 1 mA Push-Pull VSIM1 × 0.2 SIM1IO IOL = 1 mA Open-Drain 0.3 1.8 V / 2.95 1.7 V to V 3.3 V (Supplied by LDO) 1.8 V / 2.95 V (Supplied by LDO) SIM2RST IOL = 1 mA Push-Pull SIM2CLK IOL = 1 mA Push-Pull SIM2IO IOL = 1 mA Open-Drain 0.3 SIMIO IOL = 1 mA Open-Drain 0.3 VSIM2 × 0.2 V VSIM2 × 0.2 VI = OE 1.7 V to 3.3 V 1.8 V / 2.95 V (Supplied by LDO) 1.8 V / 2.95 V (Supplied by LDO) ±1 µA VI = VCCI IO = 0 1.7 V to 3.3 V 1.8 V / 2.95 V (Supplied by LDO) 1.8 V / 2.95 V (Supplied by LDO) ±5 µA SIM_I/O port 7 SIMx port 4 Control inputs UNIT VSIM1 × 0.8 IOH = –100 µA Push-Pull IOH = –10 µA Open-Drain MIN IOH = –10 µA Open-Drain ICC I/O Cio VDDIO SIM2IO Control inputs II TEST CONDITIONS VI = V_I/O or GND 3 pF pF Clock input (1) All typical values are at TA = 25°C. Submit Documentation Feedback © 2011, Texas Instruments Incorporated Product Folder Link(s): TXS02324 11 TXS02324 SCES823 – FEBRUARY 2011 www.ti.com ELECTRICAL CHARACTERISTICS LDO (Control Input Logic = High) over operating free-air temperature range (unless otherwise noted) PARAMETER VBAT Input voltage VOUT Output voltage VDO Dropout voltage TEST CONDITIONS TYP (1) 2.3 MAX UNIT 5.5 V Class-B Mode 2.82 2.95 3.18 Class-C Mode 1.65 1.8 1.95 IOUT = 50 mA 100 IOUT = 0 mA 35 IOUT = 50 mA 150 IGND Ground-pin current ISHDN Shutdown current (IGND) VENx ≤ 0.4 V, (VSIMx + VDO) ≤ VBAT ≤ 5.5 V, TJ = 85°C IOUT(SC) Short-circuit current RL = 0 Ω COUT Output Capacitor f = 1 kHz 50 PSRR Power-supply rejection ratio f = 10 kHz 40 TSTR Start-up time VSIMx = 1.8 V or 3 V, IOUT = 10 mA, COUT = 1 µF TJ Operating junction temperature V mV µA 3 µA 400 mA µF 1 VBAT = 3.25 V, VSIMx = 1.8 V or 3 V, COUT = 1 µF, IOUT = 50 mA (1) MIN dB 50 –40 85 µS °C All typical values are at TA = 25°C. GENERAL ELECTRICAL CHARACTERISTICS over operating free-air temperature range (unless otherwise noted) PARAMETER Hyst Internal hysteresis of comparator RSIMPU SIM I/O pull-up RSIMxPU SIMx I/O pull-up RSIMPD SIMx I/O pull-down 12 TEST CONDITIONS MIN TYP 20 kΩ 7.5 Class C 4.5 Submit Documentation Feedback UNIT mV Class B Active pull-downs are connected to the VSIM1/2 regulator output to the SIM1/2 CLK, SIM1/2 RST, SIM1/2 I/O when the respective regulator is disabled MAX ±50 2 kΩ kΩ © 2011, Texas Instruments Incorporated Product Folder Link(s): TXS02324 TXS02324 SCES823 – FEBRUARY 2011 www.ti.com SWITCHING CHARACTERISTICS VSIMx = 1.8 V or 2.95 V Supplied by Internal LDO, VBAT = 2.3V to 5.5V over recommended operating free-air temperature range (unless otherwise noted) TEST CONDITIONS PARAMETER SIMIO trA Baseband side to SIM side trA Baseband side to SIM side V_I/O = 1.7 V to 3.3 V TYP UNIT Open Drain 210 ns SIMRST Push Pull 4.3 ns SIMCLK Push Pull 4 ns SIMxIO Open Drain 16 ns SIMRST Push Pull 4 ns SIMxCLK Push Pull 5 ns trB SIM side to Baseband side SIMxIO Open Drain 210 ns trB SIM side to Baseband side SIMxIO Open Drain 6 ns fmax SIMxCLK Push Pull 5 MHz SIMCLK to SIMxCLK Push Pull 8 ns SIMRST to SIMxRST Push Pull 8 ns tPLH tPHL SIMIO to SIMxIO Open Drain 260 ns SIMxIO to SIMIO Open Drain 260 ns SIMCLK to SIMxCLK Push Pull 7 ns SIMRST to SIMxRST Push Pull 7 ns SIMIO to SIMxIO Open Drain 23 ns SIMxIO to SIMIO Open Drain 23 ns Submit Documentation Feedback © 2011, Texas Instruments Incorporated Product Folder Link(s): TXS02324 13 TXS02324 SCES823 – FEBRUARY 2011 www.ti.com OPERATING CHARACTERISTICS TA = 25°C, VSIMx = 1.8 V for Class C, VSIMx = 2.95 V for Class B PARAMETER Cpd (1) 14 (1) Class B Class C TEST CONDITIONS CL = 0, f = 5 MHz, tr = tf = 1 ns TYP UNIT 11 9.5 pF Power dissipation capacitance per transceiver Submit Documentation Feedback © 2011, Texas Instruments Incorporated Product Folder Link(s): TXS02324 TXS02324 SCES823 – FEBRUARY 2011 www.ti.com APPLICATION INFORMATION The LDO’s included on the TXS02324 achieve ultra-wide bandwidth and high loop gain, resulting in extremely high PSRR at very low headroom (VBAT – VSIM1/2). The TXS02324 provides fixed regulation at 1.8V or 2.95V. Low noise, enable (through I2C control), low ground pin current make it ideal for portable applications. The device offers sub-bandgap output voltages, current limit and thermal protection, and is fully specified from –40°C to +85°C. VSIM1 VDDIO TXS02324 VBAT 0.1μF GND 0.1μF VSIM2 0.1μF 0.1μF Figure 2. Typical Application circuit for TXS02324 Input and Output Capacitor Requirements It is good analog design practice to connect a 1.0 μF low equivalent series resistance (ESR) capacitor across the input supply (VBAT) near the regulator. Also, a 0.1uF is required for the logic core supply (VDDIO). This capacitor will counteract reactive input sources and improve transient response, noise rejection, and ripple rejection. A higher-value capacitor may be necessary if large, fast rise-time load transients are anticipated or if the device is located several inches from the power source. The LDO’s are designed to be stable with standard ceramic capacitors of values 1.0 μF or larger. X5R- and X7R-type capacitors are best because they have minimal variation in value and ESR over temperature. Maximum ESR should be < 1.0 Ω. Output Noise In most LDO’s, the bandgap is the dominant noise source. To improve ac performance such as PSRR, output noise, and transient response, it is recommended that the board be designed with separate ground planes for VIN and VOUT, with each ground plane connected only at the GND pin of the device. In addition, the ground connection for the bypass capacitor should connect directly to the GND pin of the device. Internal Current Limit The TXS02324 internal current limit helps protect the regulator during fault conditions. During current limit, the output sources a fixed amount of current that is largely independent of output voltage. For reliable operation, the device should not be operated in a current limit state for extended periods of time. The PMOS pass element in the TXS02324 has a built-in body diode that conducts current when the voltage at VSIM1/2 exceeds the voltage at VBAT. This current is not limited, so if extended reverse voltage operation is anticipated, external limiting may be appropriate. Dropout Voltage The TXS02324 uses a PMOS pass transistor to achieve low dropout. When (VBAT – VSIM1/2) is less than the dropout voltage (VDO), the PMOS pass device is in its linear region of operation and the input-to-output resistance is the RDS(ON) of the PMOS pass element. VDO will approximately scale with output current because the PMOS device behaves like a resistor in dropout. Startup The TXS02324 uses a quick-start circuit which allows the combination of very low output noise and fast start-up times. Note that for fastest startup, VBATT should be applied first, and then enabled by asserting the I2C register. Submit Documentation Feedback © 2011, Texas Instruments Incorporated Product Folder Link(s): TXS02324 15 TXS02324 SCES823 – FEBRUARY 2011 www.ti.com Transient Response As with any regulator, increasing the size of the output capacitor reduces over/undershoot magnitude but increases duration of the transient response. Minimum Load The TXS02324 is stable and well-behaved with no output load. Traditional PMOS LDO regulators suffer from lower loop gain at very light output loads. The TXS02324 employs an innovative low-current mode circuit to increase loop gain under very light or no-load conditions, resulting in improved output voltage regulation performance down to zero output current. THERMAL INFORMATION Thermal Protection Thermal protection disables the output when the junction temperature rises to approximately +160°C, allowing the device to cool. When the junction temperature cools to approximately +140°C the output circuitry is again enabled. Depending on power dissipation, thermal resistance, and ambient temperature, the thermal protection circuit may cycle on and off. This cycling limits the dissipation of the regulator, protecting it from damage because of overheating. Any tendency to activate the thermal protection circuit indicates excessive power dissipation or an inadequate heat sink. For reliable operation, junction temperature should be limited to +85°C maximum. To estimate the margin of safety in a complete design (including heat sink), increase the ambient temperature until the thermal protection is triggered; use worst-case loads and signal conditions. For good reliability, thermal protection should trigger at least +35°C above the maximum expected ambient condition of your particular application. This configuration produces a worst-case junction temperature of +85°C at the highest expected ambient temperature and worst-case load. The internal protection circuitry of the TXS02324 has been designed to protect against overload conditions. It was not intended to replace proper heat sinking. Continuously running the TXS02324 into thermal shutdown will degrade device reliability. TYPICAL CHARACTERISTICS 110 -80 90 -70 -60 -50 2.95 V Vsim -40 -30 -20 80 85°C Vsim 70 60 50 40 -40°C Vsim 30 20 -10 0 100 25°C Vsim 10 1000 10000 100000 f - Frequency - Hz Figure 3. PSRR 16 100 1.8 V Vsim VDO - Dropout Voltage - mV PSRR - Power Supply Rejection Ratio - dB -90 1000000 0 0 5 10 15 20 25 30 35 40 IOUT - Output Current - mA 45 50 Figure 4. Dropout Voltage vs Output Current Submit Documentation Feedback © 2011, Texas Instruments Incorporated Product Folder Link(s): TXS02324 TXS02324 SCES823 – FEBRUARY 2011 www.ti.com 0 IO = 50 mA -0.2 -0.4 -100 mA, Vsim DVOUT - Output Voltage - % DVOUT - Output Voltage - % TYPICAL CHARACTERISTICS (continued) 1 0.8 0.6 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 -1 -1.2 -1.4 -1.6 -1.8 -2 -2.2 -2.4 -40 -30 -20 -10 -50 mA, Vsim -0.6 -40°C Vsim 85°C Vsim -0.8 -1 -1.2 -1.4 25°C Vsim -1.6 -1.8 0 -2 0 10 20 30 40 50 60 70 80 5 10 TA - Temperature - °C Figure 5. Output Voltage vs Temperature, Class-B/C 45 50 Figure 6. Load Regulation, Iout = 50 mA, Class-C 0.2 0 0 -0.2 -40°C Vsim IO = 50 mA -0.4 -0.2 DVOUT - Output Voltage - % DVOUT - Output Voltage - % 15 20 25 30 35 40 IOUT - Output Current - mA -0.4 -0.6 25°C Vsim -0.8 85°C Vsim -1 -1.2 -1.4 -1.6 -0.6 -0.8 -40°C Vsim -1 -1.2 25°C Vsim -1.4 -1.6 85°C Vsim -1.8 -2 IO = 50 mA -1.8 -2 0 5 10 15 20 25 30 35 40 IOUT - Output Current - mA 45 Figure 7. Load Regulation, Iout = 50 mA, Class-B -2.2 50 -2.4 2.7 3.1 3.5 3.9 4.3 VBAT - V 4.7 5.1 5.5 Figure 8. Line Regulation, Iout = 50 mA, Class-C Submit Documentation Feedback © 2011, Texas Instruments Incorporated Product Folder Link(s): TXS02324 17 TXS02324 SCES823 – FEBRUARY 2011 www.ti.com TYPICAL CHARACTERISTICS (continued) 330 0 300 DVOUT - Output Voltage - % -0.4 -40°C Vsim 270 IOUT(SC) - Output Current - mA -0.2 IO = 50 mA -0.6 -0.8 25°C Vsim -1 85°C Vsim -1.2 -1.4 -1.6 -1.8 240 210 25°C Vsim 150 120 90 60 -2.2 30 Figure 9. Line Regulation, Iout = 50 mA, Class-B 85°C Vsim 180 -2 -2.4 3.1 3.3 3.5 3.7 3.9 4.1 4.3 4.5 4.7 4.9 5.1 5.3 5.5 VBAT - V -40°C Vsim 0 2.7 3.1 3.5 3.9 4.3 VBAT - V 4.7 5.1 5.5 Figure 10. Current Limit vs Input Voltage, Class-B/C 150 -50 mA, Vsim IGND - Ground Current - mA 120 90 60 30 -100 mA, Vsim 0 -40 -30 -20 -10 20 30 40 50 60 70 80 TA - ºC Figure 11. Ground Current vs Temperature, Class-C 18 0 10 Submit Documentation Feedback © 2011, Texas Instruments Incorporated Product Folder Link(s): TXS02324 PACKAGE OPTION ADDENDUM www.ti.com 19-Feb-2011 PACKAGING INFORMATION Orderable Device TXS02324RUKR Status (1) ACTIVE Package Type Package Drawing QFN RUK Pins Package Qty 20 3000 Eco Plan (2) Green (RoHS & no Sb/Br) Lead/ Ball Finish MSL Peak Temp (3) Samples (Requires Login) CU NIPDAU Level-2-260C-1 YEAR (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 12-Feb-2011 TAPE AND REEL INFORMATION *All dimensions are nominal Device TXS02324RUKR Package Package Pins Type Drawing QFN RUK 20 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 3000 330.0 12.4 Pack Materials-Page 1 3.3 B0 (mm) K0 (mm) P1 (mm) 3.3 1.1 8.0 W Pin1 (mm) Quadrant 12.0 Q2 PACKAGE MATERIALS INFORMATION www.ti.com 12-Feb-2011 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TXS02324RUKR QFN RUK 20 3000 346.0 346.0 29.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP® Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com Wireless www.ti.com/wireless-apps RF/IF and ZigBee® Solutions www.ti.com/lprf TI E2E Community Home Page e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2011, Texas Instruments Incorporated