TI LP3987ITLX-2.8

LP3987
www.ti.com
SNVS164G – OCTOBER 2001 – REVISED MAY 2013
Micropower DSBGA 150-mA Ultra Low-Dropout CMOS Voltage Regulator
With Sleep MODE
Check for Samples: LP3987
FEATURES
DESCRIPTION
•
•
The LP3987 is a 150mA fixed output voltage
regulator with very low dropout voltage designed
specially to meet requirements of battery-powered
applications. The additional sleep MODE feature will
reduce current consumption during standby operation
to prolong the usage of battery.
1
2
•
•
Miniature 5-I/O DSBGA Package
Stable With Ceramic and High-Quality
Tantalum Output Capacitors
Logic Controlled Enable
Thermal Shutdown and Short-Circuit Current
Limit
Dropout Voltage: 100mV maximum dropout with
150mA load.
APPLICATIONS
•
•
•
•
•
•
•
Shutdown: Less than 1µA quiescent current.
CDMA Cellular Handsets
Wideband CDMA Cellular Handsets
GSM Cellular Handsets
Portable Information Appliances
µP/DSP Power Supplies
Digital Cameras
SRAM Backup
Sleep Mode: Typically 14µA quiescent current during
sleep MODE to reduce battery consumption.
Enhanced Stability: The LP3987 is stable with
minimum 1µF±20% low ESR ceramic output
capacitor as low as 5mΩ and high quality tantalum
capacitors.
The LP3987 is available in a thin 5 Bump DSBGA
package. Performance is specified for −40°C to
125°C.
KEY SPECIFICATIONS
•
•
•
•
•
•
•
•
This device is available with output voltage options of
2.5V, 2.6V, 2.8V, 2.85V, and 3.0V. For other voltage
options, please contact Texas Instruments.
2.7 to 6.0V Input Range
150 mA Output Current
1μA Quiescent Current on Shutdown
100 mV Maximum Dropout with 150 mA Load
50dB PSRR at 10KHz
Sleep MODE Features
Over Temperature & Over Current Protection
−40°C to +125°C Junction Temperature Range
for Operation
Typical Application Circuit
C3
VIN
VOUT
C1
1PF
1PF
LP3987
A1
VEN
A3
MODE
B2
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2001–2013, Texas Instruments Incorporated
LP3987
SNVS164G – OCTOBER 2001 – REVISED MAY 2013
www.ti.com
Block Diagram
Figure 1. LP3987
Connection Diagram
Figure 2. Top View
5 I/O DSBGA Package
See Package Number YZR0005ADA
PIN DESCRIPTIONS
(1)
2
Name
Pin (1)
VEN
A1
Enable Input Logic, Enable High
GND
B2
Common Ground
VOUT
C1
Output voltage of the LDO
VIN
C3
Input voltage of the LDO
MODE
A3
Power Mode Control, Active = 1, Sleep Mode = 0
Function
The pin numbering scheme for the DSBGA package was revised in April, 2002 to conform to JEDEC standard. Only the pin numbers
were revised. No changes to the physical location of the inputs/outputs were made. For reference purposes, the obsolete numbering
scheme had VEN as pin 1, GND as pin 2, VOUT as pin 3, VIN as pin 4, and MODE as pin 5.
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: LP3987
LP3987
www.ti.com
SNVS164G – OCTOBER 2001 – REVISED MAY 2013
ORDERING INFORMATION (1) (2)
DSBGA Package
LP3987 Supplied as 250 Units
Tape and Reel
LP3987 Supplied as 3000 Units
Tape and Reel
2.5V
LP3987ITL-2.5
LP3987ITLX-2.5
2.6V
LP3987ITL-2.6
LP3987ITLX-2.6
Output Voltage
Grade
2.8V
(1)
(2)
LP3987ITL-2.8
LP3987ITLX-2.8
2.85V
STD
LP3987ITL-2.85
LP3987ITLX-2.5
3.0V
LP3987ITL-3.0
LP3987ITLX-3.0
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
web site at www.ti.com.
Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings
(1) (2) (3)
−0.3 to 6.5V
VIN
−0.3 to 6.5V
VEN, VMODE
−0.3V to(V IN+ 0.3V) ≤ 6.5
VOUT
−65°C to +150°C
Storage Temperature
ESD
(4)
Human Body Model
2KV
Machine Model
Maximum Power Dissipation
(1)
(2)
(3)
(4)
(5)
(5)
θJA (DSBGA small bump)
(1) (2)
VIN
VOUT+ 200mV to 6V
VEN, VMODE
0 to 6.0V
−40°C to +125°C
Junction Temperature
Maximum Power Dissipation
(2)
(3)
255°C/W
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltages are with respect to the potential at the GND pin.
If Military/Aerospace specified devices are required, please contact theTI Sales Office/Distributors for availability and specifications.
The human body model is 100pF discharged through 1.5kΩ.
The Absolute Maximum power dissipation depends on the ambient temperature and can be calculated using the formula:PD = (TJ TA)/θJA,Where TJ is the junction temperature, TA is the ambient temperature, and θJA is the junction-to-ambient thermal resistance. For
instant, if VIN in target application is 4.2V and worse case current consumption is 90mA. Therefore PMAX_DISSIPATION = (4.2-2.7)*0.09
=135mW. With PMAX_DISSIPATION is 135mW, TJmax is 125°C and worse case ambient temperature (TA ) in target application is 85°C, θJA
= (125-85)/0.135 = 296°C/W.
Operating Ratings
(1)
200V
(3)
392mW at 25°C
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltages are with respect to the potential at the GND pin.
The Absolute Maximum power dissipation depends on the ambient temperature and can be calculated using the formula:PD = (TJ TA)/θJA,Where TJ is the junction temperature, TA is the ambient temperature, and θJA is the junction-to-ambient thermal resistance. For
instant, if VIN in target application is 4.2V and worse case current consumption is 90mA. Therefore PMAX_DISSIPATION = (4.2-2.7)*0.09
=135mW. With PMAX_DISSIPATION is 135mW, TJmax is 125°C and worse case ambient temperature (TA ) in target application is 85°C, θJA
= (125-85)/0.135 = 296°C/W.
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: LP3987
3
LP3987
SNVS164G – OCTOBER 2001 – REVISED MAY 2013
www.ti.com
Electrical Characteristics
Unless otherwise specified: VEN = 1.8V, MODE = 1.8V, VIN = VOUT(nom) + 0.5V, CIN = 1 µF, IOUT = 1mA, COUT = 1 µF.
Typical values and limits appearing in standard typeface are for TJ = 25°C. Limits appearing in boldface type apply over the
entire junction temperature range for operation, −40°C to +125°C. (1) (2)
Parameter
Test Conditions
Output Voltage Tolerance
IOUT = 1mA, 25°C
-2
2
IOUT = 1mA
−3
3
% of
VOUT(nom)
−0.1
0.1
%/V
0.0004
0.002
%/mA
Load Regulation Error
IOUT = 1mA to 150 mA
Dropout Voltage
Unit
Max
VIN = (VOUT(nom) + 0.5V) to 6.0V,
IOUT = 1 mA
(3)
Limit
Min
Line Regulation Error
ΔVOUT
Typ
IOUT = 1mA
0.4
2
IOUT = 150mA
60
100
(4)
mV
ΔVOUT(SLEEP)
Output Voltage difference at
MODE = 0V
MODE = 0V,
Transient
Response
Line Transient Response (5)
MODE = 1.8V, ILOAD = 100mA, TRISE
= TFALL = 10µS,
VIN = 600mV P-P AC Square wave, (6)
21
mVpp
Load Transient Response (5)
MODE = 1.8V, COUT = 4.7µF, TRISE =
TFALL = 100nS,
VIN = 3.1V, 3.6V, 4.2V, (7) (8)
100
mVpk
VIN = VOUT(nom) + 1V, MODE = 1.8V, f
= <10 kHz,
IOUT = 1mA
50
VIN = VOUT(nom) + 1V, MODE = 0V, f =
<10 kHz,
IOUT = 1mA
10
MODE = 1.8V, IOUT = 0mA, VIN =
4.2V
85
120
MODE = 1.8V, IOUT = 150mA, VIN =
4.2V
160
200
1
3
21
PSRR
Power Supply Rejection
Ratio (5)
IQ(ON)
Quiescent Current
-150
+100
mV
dB
µA
IQ(OFF)
Quiescent Current
ENABLE = 0V, VIN = 4.2V
µA
IQ(SLEEP)
Current in Standby Mode
MODE = 0V, IOUT = 50µA, VIN = 4.2V
14
ISC
Short Circuit Current Limit (5)
Output Grounded
600
ISC(SLEEP)
Short Circuit Current in Sleep
MODE
Output Grounded
28
IOUT(ON)
Maximum Output Current at
MODE = 1.8V
MODE = 1.8V
IOUT(SLEEP)
Maximum Output Current at
MODE = 0V
MODE = 0V
en
Output Noise Voltage (5)
BW = 10 Hz to 100 kHz,
COUT = 1µF
70
µVrms
TSHUTDOWN
Shutdown Temperature (5)
Sleep MODE = 1.8V
155
°C
µA
mA
43
150
mA
mA
3
mA
Logic Control Characteristics
IEN
Maximum Input Current at EN
VEN = 0 and VIN= 6.0V
VIL
Logic Low Input Threshold
VIN = 3.05 to 6V
VIH
Logic High Input Threshold
VIN = 3.05 to 6V
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
4
0.015
µA
0.5
V
1.2
V
Min and Max Limits are verified by design, test, or statistical analysis. Typical (Typ.) numbers are not verified, but do represent the most
likely norm.
The nominal output voltage, which is labeled VOUT(nom), is the output voltage measured with the input 0.5V above VOUT(nom) and a 1mA
load.
Dropout voltage is defined as the input to output voltage differential at which the output voltage falls to 100mV below the nominal output
voltage. VIN less than minimum operating voltage may be used for test purposes.
On/Sleep Mode voltage tolerance and current capability requirement. See Figure 3.
This electrical specification is specified by design.
Line Transient response requirement. See Figure 4.
Load Transient response requirement. See Figure 5.
During transient recovery, output voltage should not be oscillating.
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: LP3987
LP3987
www.ti.com
SNVS164G – OCTOBER 2001 – REVISED MAY 2013
Electrical Characteristics (continued)
Unless otherwise specified: VEN = 1.8V, MODE = 1.8V, VIN = VOUT(nom) + 0.5V, CIN = 1 µF, IOUT = 1mA, COUT = 1 µF.
Typical values and limits appearing in standard typeface are for TJ = 25°C. Limits appearing in boldface type apply over the
entire junction temperature range for operation, −40°C to +125°C. (1) (2)
Parameter
Test Conditions
VMODE_L
Logic Low Input Threshold
VIN = 3.05 to 6V
VMODE_H
Logic High Input Threshold
VIN = 3.05 to 6V
IMODE
Maximum Input Current at
VMODE
VMODE = 0 and VIN = 6.0V
Typ
Limit
Min
Max
Unit
0.5
V
1.2
V
µA
0.015
Timing Characteristics
TON
Turn on Time (On Mode) (5)
(9)
TSLEEP
Turn on Time (Sleep
Mode) (5) (10)
MODE = 0V, COUT = 4.7µF
TMODE
Sleep to On Mode Settle
Time (5) (11)
COUT = 4.7µF, Enable = 1.8V
MODE = 1.8V, COUT = 4.7µF
170
250
5
0.5
µs
ms
300
200
µs
(9) TON is measured from rising edge of Enable with MODE = 1.8V to when VOUT reaches 95% of final value.
(10) TSLEEP is measured from rising edge of Enable with MODE = 0V to when VOUT reaches 95% of final value.
(11) TMODE is measured from rising edge of MODE with ENABLE = 1.8V to time before full current capability.
Figure 3.
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: LP3987
5
LP3987
SNVS164G – OCTOBER 2001 – REVISED MAY 2013
www.ti.com
Figure 4.
Figure 5.
6
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: LP3987
LP3987
www.ti.com
SNVS164G – OCTOBER 2001 – REVISED MAY 2013
Typical Performance Characteristics
Unless otherwise specified, CIN = COUT = 1 µF Ceramic, VIN = VOUT(nom) + 0.5V, TA = 25°C, Enable pin is tied to VIN, MODE =
1.8V.
Ground Current at TA = 25°C
Ground Current at TA = 40°C
Figure 6.
Figure 7.
Ground Current at TA = 85°C
Dropout Voltage
vs
Load Current
Figure 8.
Figure 9.
Ripple Rejection (CIN = COUT = 1µF, IL = 1mA)
Ripple Rejection (VIN = VOUT(nom) + 1V,
CIN = COUT = 1µF, IL = 1mA)
Figure 10.
Figure 11.
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: LP3987
7
LP3987
SNVS164G – OCTOBER 2001 – REVISED MAY 2013
www.ti.com
Typical Performance Characteristics (continued)
Unless otherwise specified, CIN = COUT = 1 µF Ceramic, VIN = VOUT(nom) + 0.5V, TA = 25°C, Enable pin is tied to VIN, MODE =
1.8V.
8
TSLEEP at MODE = 0V, COUT = 1µF,
IL = 1mA
TSLEEP at MODE = 0V, COUT = 1µF,
IL = 1mA
Figure 12.
Figure 13.
TON at MODE = 1.8V, COUT = 1µF,
IL = 150mA
TON at MODE = 1.8V, COUT = 1µF,
IL = 150mA
Figure 14.
Figure 15.
TSLEEP at MODE = 0V, COUT = 4.7µF,
IL = 1mA
TSLEEP at MODE = 0V, COUT = 4.7µF,
IL = 1mA
Figure 16.
Figure 17.
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: LP3987
LP3987
www.ti.com
SNVS164G – OCTOBER 2001 – REVISED MAY 2013
Typical Performance Characteristics (continued)
Unless otherwise specified, CIN = COUT = 1 µF Ceramic, VIN = VOUT(nom) + 0.5V, TA = 25°C, Enable pin is tied to VIN, MODE =
1.8V.
TON at MODE = 1.8V, COUT = 4.7µF,
IL = 150mA
TON at MODE = 1.8V, COUT = 4.7µF,
IL = 150mA
Figure 18.
Figure 19.
TMODE Measurement at VIN = 3.05V
TMODE Measurement at VIN = 3.6V
Figure 20.
Figure 21.
TMODE Measurement at VIN = 4.2V
Output Short Circuit Current
Figure 22.
Figure 23.
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: LP3987
9
LP3987
SNVS164G – OCTOBER 2001 – REVISED MAY 2013
www.ti.com
Typical Performance Characteristics (continued)
Unless otherwise specified, CIN = COUT = 1 µF Ceramic, VIN = VOUT(nom) + 0.5V, TA = 25°C, Enable pin is tied to VIN, MODE =
1.8V.
10
Output Short Circuit Current
Load Transient Response at VIN = 3.1V
Figure 24.
Figure 25.
Load Transient Response at VIN = 3.35V
Load Transient Response at VIN = 3.6V
Figure 26.
Figure 27.
Load Transient Response at VIN = 4.2V
Load Transient Response at VIN = 3.1V, COUT = 1µF
Figure 28.
Figure 29.
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: LP3987
LP3987
www.ti.com
SNVS164G – OCTOBER 2001 – REVISED MAY 2013
Typical Performance Characteristics (continued)
Unless otherwise specified, CIN = COUT = 1 µF Ceramic, VIN = VOUT(nom) + 0.5V, TA = 25°C, Enable pin is tied to VIN, MODE =
1.8V.
Load Transient Response at VIN = 3.35V, COUT = 1µF
Load Transient Response at VIN = 4.2V, COUT = 1µF
Figure 30.
Figure 31.
Load Transient Response at VIN = 3.6V, COUT = 1µF
Output Voltage Change
vs
Temperature
Figure 32.
Figure 33.
Line Transient Response
Line Transient Response
Figure 34.
Figure 35.
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: LP3987
11
LP3987
SNVS164G – OCTOBER 2001 – REVISED MAY 2013
www.ti.com
Typical Performance Characteristics (continued)
Unless otherwise specified, CIN = COUT = 1 µF Ceramic, VIN = VOUT(nom) + 0.5V, TA = 25°C, Enable pin is tied to VIN, MODE =
1.8V.
12
Line Transient Response
Line Transient Response
Figure 36.
Figure 37.
Line Transient Response
Line Transient Response
Figure 38.
Figure 39.
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: LP3987
LP3987
www.ti.com
SNVS164G – OCTOBER 2001 – REVISED MAY 2013
APPLICATION HINTS
EXTERNAL CAPACITORS
Like any low-dropout regulator, the LP3987 requires external capacitors for regulator stability. The LP3987 is
specifically designed for portable applications requiring minimum board space and smallest components. These
capacitors must be correctly selected for good performance.
INPUT CAPACITOR
An input capacitance of ≊ 1µF is required between the LP3987 input pin and ground (the amount of the
capacitance may be increased without limit).
This capacitor must be located a distance of not more than 1cm from the input pin and returned to a clean
analog ground. Any good quality ceramic, tantalum, or film capacitor may be used at the input.
Important: Tantalum capacitors can suffer catastrophic failures due to surge current when connected to a lowimpedance source of power (like a battery or a very large capacitor). If a tantalum capacitor is used at the input,
it must be specified by the manufacturer to have a surge current rating sufficient for the application.
There are no requirements for the ESR on the input capacitor, but tolerance and temperature coefficient must be
considered when selecting the capacitor to ensure the capacitance will be ≊ 1µF over the entire operating
temperature range.
OUTPUT CAPACITOR
The LP3987 is designed specifically to work with very small ceramic output capacitors. A ceramic capacitor
(dielectric types Z5U, Y5V or X7R) in 1 to 4.7 µF range with 5mΩ to 500mΩ ESR range is suitable in the LP3987
application circuit.
It may also be possible to use tantalum or film capacitors at the output, but these are not as attractive for
reasons of size and cost (see next section Capacitor Characteristics).
The output capacitor must meet the requirement for minimum amount of capacitance and also have an ESR
(Equivalent Series Resistance) value which is within a stable range (5 mΩ to 500 mΩ).
NO-LOAD STABILITY
The LP3987 will remain stable and in regulation with no external load. This is specially important in CMOS RAM
keep-alive applications.
CAPACITOR CHARACTERISTICS
The LP3987 is designed to work with ceramic capacitors on the output to take advantage of the benefits they
offer: for capacitance values in the range of 1µF to 4.7µF range, ceramic capacitors are the smallest, least
expensive and have the lowest ESR values (which makes them best for eliminating high frequency noise). The
ESR of a typical 1µF ceramic capacitor is in the range of 20 mΩ to 40 mΩ, which easily meets the ESR
requirement for stability by the LP3987. The ceramic capacitor's capacitance can vary with temperature. Most
large value ceramic capacitors (≊ 2.2µF) are manufactured with Z5U or Y5V temperature characteristics, which
results in the capacitance dropping by more than 50% as the temperature goes from 25°C to 85°C.
A better choice for temperature coefficient in a ceramic capacitor is X7R, which holds the capacitance within
±15%. Tantalum capacitors are less desirable than ceramic for use as output capacitors because they are more
expensive when comparing equivalent capacitance and voltage ratings in the 1µF to 4.7µF range.
Another important consideration is that tantalum capacitors have higher ESR values than equivalent size
ceramics. This means that while it may be possible to find a tantalum capacitor with an ESR value within the
stable range, it would have to be larger in capacitance (which means bigger and more costly ) than a ceramic
capacitor with the same ESR value. It should also be noted that the ESR of a typical tantalum will increase about
2:1 as the temperature goes from 25°C down to −40°C, so some guard band must be allowed.
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: LP3987
13
LP3987
SNVS164G – OCTOBER 2001 – REVISED MAY 2013
www.ti.com
ON/OFF INPUT OPERATION
The LP3987 is turned off by pulling the VEN pin low, and turned on by pulling it high. If this feature is not used,
the VEN pin should be tied to VIN to keep the regulator output on at all time. To assure proper operation, the
signal source used to drive the VEN input must be able to swing above and below the specified turn-on/off voltage
thresholds listed in the Electrical Characteristics section under VIL and VIH.
MODE OPERATION
The LP3987 enters sleep mode by pulling MODE = 0V externally to reduce current during standby operation.
During sleep mode, LP3987 consumes only 14µA of quiescent current and supplies up to 3mA of current. The
device returns to active mode by pulling MODE = 1.8V. If this function is not used, the MODE pin should be tied
to VIN.
THERMAL PROTECTION
The LP3987 has internal thermal protection circuitry to disable the internal pass transistor if the junction
temperature exceeds 125°C to allow the device to cool down. The pass transistor will turn on when temperature
falls below the maximum operating junction temperature of 125°C. This feature is designed to protect the device
in the event of fault conditions. For normal operation, it is suggested to limit the device junction temperature to
less than 125°C.
DSBGA MOUNTING
The DSBGA package requires specific mounting techniques which are detailed in Texas Instruments AN-1112
Application Report (SNOA401). Referring to the section PCB Layout, note that the pad style which must be used
with the 5 pin package is NSMD (non-solder mask defined) type.
For best results during assembly, alignment ordinals on the PC board may be used to facilitate placement of the
DSBGA device.
DSBGA LIGHT SENSITIVITY
Exposing the DSBGA device to direct sunlight will cause misoperation of the device. Light sources such as
Halogen lamps can effect electrical performance if brought near to the device. The wavelengths which have most
detrimental effect are reds and infra-reds, which means that the fluorescent lighting used inside most buildings
has very little effect on performance. A DSBGA test board was brought to within 1cm of a fluorescent desk lamp
and the effect on the regulated output voltage was negligible, showing a deviation of less than 0.1% from
nominal.
14
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: LP3987
LP3987
www.ti.com
SNVS164G – OCTOBER 2001 – REVISED MAY 2013
REVISION HISTORY
Changes from Revision F (May 2013) to Revision G
•
Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 14
Submit Documentation Feedback
Copyright © 2001–2013, Texas Instruments Incorporated
Product Folder Links: LP3987
15
PACKAGE OPTION ADDENDUM
www.ti.com
3-May-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
(4)
LP3987ITL-2.5/NOPB
ACTIVE
DSBGA
YZR
5
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
7
LP3987ITL-2.6/NOPB
ACTIVE
DSBGA
YZR
5
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 125
7
LP3987ITL-2.8/NOPB
ACTIVE
DSBGA
YZR
5
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 125
7
LP3987ITL-2.85/NOPB
ACTIVE
DSBGA
YZR
5
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 125
7
LP3987ITL-3.0/NOPB
ACTIVE
DSBGA
YZR
5
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
7
LP3987ITLX-2.5/NOPB
ACTIVE
DSBGA
YZR
5
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
7
LP3987ITLX-2.6/NOPB
ACTIVE
DSBGA
YZR
5
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 125
7
LP3987ITLX-2.8/NOPB
ACTIVE
DSBGA
YZR
5
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 125
7
LP3987ITLX-2.85/NOPB
ACTIVE
DSBGA
YZR
5
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
-40 to 125
7
LP3987ITLX-3.0/NOPB
ACTIVE
DSBGA
YZR
5
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
7
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
(3)
3-May-2013
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
8-May-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
LP3987ITL-2.5/NOPB
DSBGA
YZR
5
250
178.0
8.4
LP3987ITL-2.6/NOPB
DSBGA
YZR
5
250
178.0
LP3987ITL-2.8/NOPB
DSBGA
YZR
5
250
178.0
LP3987ITL-2.85/NOPB
DSBGA
YZR
5
250
LP3987ITL-3.0/NOPB
DSBGA
YZR
5
LP3987ITLX-2.5/NOPB
DSBGA
YZR
LP3987ITLX-2.6/NOPB
DSBGA
YZR
LP3987ITLX-2.8/NOPB
DSBGA
LP3987ITLX-2.85/NOPB
LP3987ITLX-3.0/NOPB
1.09
1.55
0.76
4.0
8.0
Q1
8.4
1.09
1.55
0.76
4.0
8.0
Q1
8.4
1.09
1.55
0.76
4.0
8.0
Q1
178.0
8.4
1.09
1.55
0.76
4.0
8.0
Q1
250
178.0
8.4
1.09
1.55
0.76
4.0
8.0
Q1
5
3000
178.0
8.4
1.09
1.55
0.76
4.0
8.0
Q1
5
3000
178.0
8.4
1.09
1.55
0.76
4.0
8.0
Q1
YZR
5
3000
178.0
8.4
1.09
1.55
0.76
4.0
8.0
Q1
DSBGA
YZR
5
3000
178.0
8.4
1.09
1.55
0.76
4.0
8.0
Q1
DSBGA
YZR
5
3000
178.0
8.4
1.09
1.55
0.76
4.0
8.0
Q1
Pack Materials-Page 1
W
Pin1
(mm) Quadrant
PACKAGE MATERIALS INFORMATION
www.ti.com
8-May-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LP3987ITL-2.5/NOPB
DSBGA
YZR
5
250
210.0
185.0
35.0
LP3987ITL-2.6/NOPB
DSBGA
YZR
5
250
210.0
185.0
35.0
LP3987ITL-2.8/NOPB
DSBGA
YZR
5
250
210.0
185.0
35.0
LP3987ITL-2.85/NOPB
DSBGA
YZR
5
250
210.0
185.0
35.0
LP3987ITL-3.0/NOPB
DSBGA
YZR
5
250
210.0
185.0
35.0
LP3987ITLX-2.5/NOPB
DSBGA
YZR
5
3000
210.0
185.0
35.0
LP3987ITLX-2.6/NOPB
DSBGA
YZR
5
3000
210.0
185.0
35.0
LP3987ITLX-2.8/NOPB
DSBGA
YZR
5
3000
210.0
185.0
35.0
LP3987ITLX-2.85/NOPB
DSBGA
YZR
5
3000
210.0
185.0
35.0
LP3987ITLX-3.0/NOPB
DSBGA
YZR
5
3000
210.0
185.0
35.0
Pack Materials-Page 2
MECHANICAL DATA
YZR0005xxx
D
0.600±0.075
E
TLA05XXX (Rev C)
D: Max = 1.502 mm, Min =1.441 mm
E: Max = 1.045 mm, Min =0.984 mm
4215043/A
NOTES:
A. All linear dimensions are in millimeters. Dimensioning and tolerancing per ASME Y14.5M-1994.
B. This drawing is subject to change without notice.
www.ti.com
12/12
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated