Ordering number:ENN5828C ExPD (Excellent Power Device) TND012NM, TND012MP Lamp, solenoid, and motor-driving Applications Features · N-channel MOSFET built in · Overheat protection · Overcurrent protection · Overvoltage protection Package Dimensions Package Dimensions Unit:mm 2135 Unit:mm 2145 [TND012NM] [TND012MP] 6.0 5.0 2.5 1.45 4.7 1.0 3.0 1.0 4.5 1.0 8.5 6.9 6.0 0.5 0.6 14.0 4.0 1.0 0.6 0.5 0.9 1 2 3 0.45 1 2 3 1:GND 2:OUT 2.45 2.45 0.5 0.5 1:GND 3:IN SANYO:NMP 2:OUT 3:IN 1.45 1.45 SANYO:MP Absolute Maximum Ratings at Ta = 25˚C Parameter Symbol Conditions Ratings Unit Drain-to-Source Voltage VDS(DC) 60 V Output Current (Average) IO(DC) 1.5 A Input Voltage VIN –0.3 to +10 V Allowable Power Dissipation PD 1.0 W –40 to +150 ˚C 150 ˚C –55 to +150 ˚C Operating Temperature Topr Junction Temperature Tj Storage Temperature Tstg Electrical Characteristics at Ta = 25˚C Parameter Drain-to-Source Clamp Voltage Output-OFF Current Symbol VDS clamp VIN=0, IDSS(1) VIN=0, IDSS(2) VIN=0, VIN(th) Input Threshold Voltage Drain-to-Source ON Resistance Conditions RDS(on) IO=1mA VDS=50V VDS=12V VDS=5V, IO=1mA VIN=5V, IO=1A Ratings min typ max 60 Unit V 1.0 100 µA 10 µA 2.5 V 0.5 Ω Continued on next page. Any and all SANYO products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft’s control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO representative nearest you before using any SANYO products described or contained herein in such applications. SANYO assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges,or other parameters) listed in products specifications of any and all SANYO products described or contained herein. SANYO Electric Co.,Ltd. Semiconductor Company TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN 12501TS TA-3182/30199TS (KOTO) TA-1339 No.5828–1/4 TND012NM, 012MP Continued from preceding page. Parameter Symbol Output-ON Input Current min typ max 0.25 0.6 IIN Tj(sd) VIN=5V VIN=5V, IO=1A 155 165 Is VIN=5V 1.5 2 VIN clamp IIN=5mA 10 Overheat Detecting Temperature Overcurrent Detecting Current Input Clamp Voltage Ratings Conditions Unit mA ˚C 2.5 A V *Note: 1.Shutdown state will be kept after overheat and overcurrent protections operation and the system will be reset when the input voltage goes to or below the reset voltage (1.0V). 2.Overheat detecting temperature value is not a guarantee value but for reference only. Block Diagram OUT Overvoltage protection Overcurrent protection Gate shutdown ESD protection Latch IN Overheat protection GND RDS(on) - Ta IO=1A 0.5 5V 0.4 V V IN 0.3 =4 6V 0.2 0.1 0 -50 -25 0 25 50 75 100 125 150 RDS(on) - VIN 0.6 Drain-to-Source ON Resistance, RDS(on) – Ω Drain-to-Source ON Resistance, RDS(on) – Ω 0.6 IO= 1A 0.55 0.5 0.45 Ta=85˚C 0.4 0.35 25˚C 0.3 0.25 0.2 -40˚C 0.15 0.1 0 1 2 3 Ambient Temperature, Ta – ˚C I IN - Ta 0.6 4 5 6 7 8 9 10 11 Input Voltage, VIN – V I IN - VIN 1.0 VIN=5V Ta=25˚C 0.9 Input Current, I IN – mA Input Current, I IN – mA 0.5 0.4 0.3 0.2 0.8 0.7 0.6 n n operatio Protectio 0.5 0.4 0.3 Normal n operatio 0.2 0.1 0.1 0 -50 -25 0 25 50 75 100 Ambient Temperature, Ta – ˚C 125 150 0 0 1 2 3 4 5 6 7 8 9 10 11 Input Voltage, VIN – V No.5828–2/4 TND012NM, 012MP I s - Ta 4.0 I s - VIN 4.0 Overcurrent detecting current, Is – A Overcurrent detecting current, Is – A Ta=25˚C 3.5 3.0 5V 2.5 V IN =6V 4V 2.0 3V 1.5 1.0 0.5 0 -50 -25 0 25 50 75 100 125 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 0 150 1 2 3 Ambient Temperature, Ta – ˚C VDS clamp - Ta 70 60 50 40 30 20 10 0 -50 -25 0 25 50 75 100 125 Allowable Power Dissipation, PD – W Overheat detecting temperature, Tj(sd) – V 170 160 150 3 4 5 6 7 8 9 10 11 1.5 1.0 0.5 -25 0 25 50 75 100 125 150 PD - Ta 1.2 180 2 8 Ambient Temperature, Ta – ˚C Tj(sd) - VIN 1 7 2.0 1.0 -50 150 190 140 0 6 VDS = 5V IO= 1mA Ambient Temperature, Ta – ˚C 200 5 VIN(th) - Ta 2.5 VIN=0 IO=1mA Threshold voltage, VIN(th) – V Clamp voltage, VDS clamp – V 80 4 Input Voltage, VIN – V 9 10 1.0 0.8 0.6 0.4 0.2 0 -40 11 -20 0 20 40 60 80 100 120 140 160 Ambient Temperature, Ta – ˚C Input Voltage, VIN – V Sample Application Circuit Another Sample Application Circuit (solenoid drive) AC24V AC24V AC100V AC100V Lamp Solenoid OUT OUT IN TND012NM/MP GND Microcontroller IN 5V TND012NM/MP Microcontroller 5V GND No.5828–3/4 TND012NM, 012MP Operation description 1.The output power MOSFET will be turned on when the input voltage exceeds the input threshold voltage (5V is recommended), and then the lamp will be turned on by the current flowing to the lamp.Conversely, the output power MOSFET will be turned off when the input voltage goes below the input threshold voltage, and then the lamp will be turned off. 2.The internal overcurrent protection function shuts down the output power MOSFET when output current of at least the overcurrent detecting current value flows at load short. Besides, if the device temperature exceeds the allowable power dissipation, overheat protection function protects the power switch from being broken down by shutting down the MOSFET when Tj comes to 165˚C (typical). 3.Shutdown state will be kept after overheat and overcurrent protections operation and the system will be reset when the input voltage goes to or below the reset voltage (1.0V). 4.As an example of application circuit, DC voltage can also be controlled as a solenoid drive. Specifications of any and all SANYO products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO products(including technical data,services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be expor ted without obtaining the expor t license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Electric Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only ; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of January, 2001. Specifications and information herein are subject to change without notice. PS No.5828–4/4