INSTALLATION INSTRUCTIONS TSP-3P Series Order Code TSP 240-124-3PAC400 TSP 480-124-3PAC400 Industrial AC-Input Output Boost Output Nominal Voltage Range Power max. Output Boost for 5 Seconds 480 Watt 24.0Vdc / 10.0A 24.0Vdc / 20.0A 960 Watt 24.0Vdc / 20.0A 24.0Vdc / 40.0A 1920 Watt 24.0Vdc / 40.0A 24.0Vdc / 80.0A 480 Watt 24.0Vdc / 10.0A 24.0Vdc / 20.0A 960 Watt 24.0Vdc / 20.0A 24.0Vdc / 40.0A 1920 Watt 24.0Vdc / 40.0A 24.0Vdc / 80.0A 360Vac – 440Vac 47 – 63Hz TSP 960-124-3PAC400 TSP 240-124-3PAC500 TSP 480-124-3PAC500 Power Supply 450Vac – 550Vac TSP 960-124-3PAC500 47 – 63Hz recommended Circuit breaker / fuse 6A (Characteristic B Order Code Input Current Order Code Power Consumption ¾ TSP 240-124-3PAC400 0.50A typ Nominal Voltage ¾ TSP 240-124-3PAC400 19 Watt typ Nominal Voltage ¾ TSP 480-124-3PAC400 1.00A typ Nominal Voltage ¾ TSP 480-124-3PAC400 34 Watt typ Nominal Voltage ¾ TSP 960-124-3PAC400 1.88A typ Nominal Voltage ¾ TSP 960-124-3PAC400 68 Watt typ Nominal Voltage ¾ TSP 240-124-3PAC500 0.40A typ Nominal Voltage ¾ TSP 240-124-3PAC500 18 Watt typ Nominal Voltage ¾ TSP 480-124-3PAC500 0.77A typ Nominal Voltage ¾ TSP 480-124-3PAC500 32 Watt typ Nominal Voltage ¾ TSP 960-124-3PAC500 1.50A typ Nominal Voltage ¾ TSP 960-124-3PAC500 65 Watt typ Nominal Voltage Operating temperature range: -25°C – +70°C max Natural Air Convection Cooling -13°F – +158°F max Output Power Derating: above +55°C Î2.5%/K (6.0W/°C) above 131°F Î1.4%/°F (3.35 W/°F) above +55°C Î2.5%/K (12.0 W/°C) above 131°F Î1.4%/°F (6.7 W/°F) above +55°C Î2.5%/K (24.0 W/°C) above 131°F Î1.4%/°F (13.4 W/°F) Output Power Derating: 330Vac Î 360Vac Iout max = 100% Nominal 410Vac Î 430Vac Iout max = 50% Nominal 430Vac Î 450Vac Iout max = 100% Nominal Î TSP240-124-3PAC400/TSP240-124-3PAC500 Î TSP240-124-3PAC400/TSP240-124-3PAC500 Î TSP480-124-3PAC400/TSP480-124-3PAC500 Î TSP480-124-3PAC400/TSP480-124-3PAC500 Î TSP960-124-3PAC400/TSP960-124-3PAC500 Î TSP960-124-3PAC400/TSP960-124-3PAC500 Storage temperature range: -25°C – +85°C max -13°F – +185°F max Power Back Immunity 35Vdc continuous and 40Vdc for 1second max. Over Voltage Protection in single fault condition: Typ 30Vdc Î 33Vdc Connections: AC Input: Screw type terminal COMBI Recommended tightening torque 0.5 to 0.6Nm. DC Output: Screw type terminal COMBI Recommended tightening torque 0.5 to 0.6Nm. Output Signal: Screw type terminal COMBI Recommended tightening torque 0.5 to 0.6Nm. Case material: http://www.tracopower.com Aluminium (chassis) and Zinc-plated steel (cover) Rev: 1.2 / 5010 Safety Instructions: ¾ Before ins tallation read these ins tructions carefully and completely. This ins tallation i nstruction cannot accou nt for e very possible cond ition o f installation, o peration or maintenance. Further information can be obtained from your local distributor office or from the product datasheet, which can be down loaded from ou r website: http://www.tracopower.com/products/tsp3p.pdf. ¾ These pow er s upplies are c onstructed in accor dance with the safety r equirements o f IEC /EN/UL 60 950-1, UL508, EN 60 204, EN 50178, EN 61558-2-8, CSA22.2-60950-1 and CSA22.2-107. They are approved (BG-mark) in accordance with EN 60 950-1, EN 50178, EN 60204 and fulfil the requirements of the Low Voltage D irective (L VD). They w ill be UL an d cUL approved in accordance to UL60950-1 (recognised) and UL508 (listed) (Approvals pending). ¾ Before an y installation, ma intenance or mod ification work en sure that t he m ain swit ch i s swi tched of f and prevented fro m be ing sw itched o n aga in. Non-observance, touch ing of an y live components or improper handling o f th is power supply ca n result i n death, sev ere personal in jury or sub stantial pro perty damage. Prop er and safe op eration is de pendent on proper storage, handling, installation and operation. ¾ Compliance with the relevant national regulations (in the USA, Europe and other countries) must be ensured. Before operation is started the following conditions must be ensured: Connection to mains supply in compliance with national regulations (e.g. VDE0100 and EN50178). By use of st randed wi res, all stra nds must be fastened i n th e te rminal blocks. (Potential da nger o f contact with the case) Power supply and mains cables must be sufficiently fused. Degree o f protection = 1 according to IEC5 36. The non-fused protective earth connection must be connected to the FG terminal (Protection Class I). All output wires must be rated for the power supply output current and must be c onnected with the correct polarity. All output terminals have to be used Sufficient cooling must be ensured. ¾ Never work on the power supply if power is supplied! Ri sk of electric a rcs an d el ectrical shock, wh ich can caus e death, se vere pers onal injury or s ubstantial property damage. ¾ Warning: Hazardous voltages and components storing a very substantial amount of energy are present in this power supply during normal operating conditions. However, these are inaccessible. Improper handling may result in an electric shock or serious burns! Do not open the power supply until at least 5 minutes after it has been disconnected from the mains on all poles. Only trained personnel may open the power supply. Do not introduce any objects into the power supply. The ou tput voltage adjustment po tentiometer may only be actuated using an insulated screwdriver. Keep away from fire and water http://www.tracopower.com Installation Instructions: ¾ This p ower sup ply is designed for profe ssional indoor systems. In operat ion the powe r supply must not be accessible. It may be inst alled and put into service by qualified personnel only. ¾ Do not op erate without PE conne ction! T o comply with EMC and safety standards (CE mark, approval s) the power supply must be operated only if PE terminal is connected to the non-fused earth conductor. ¾ The co rrect mountin g position for optimal coolin g performance must be ob served. Do not cover any ventilation holes. Leave a free sp ace of minimum 80mm (3in.) above and below the power supply. Observe power derating. ¾ The inte rnal f uses a re n ot acce ssible, a s it may not be repl aced by the user . If any of this internal fuse has blown, the po wer su pply ha s mo st pro perly an internal defe ct and, for safety rea sons, mu st be shipped to the local dist ributor. In case this internal fuse has to be replaced in the field, replace only with same type and rating of fuse for continued protection against risk of fire. ¾ To comply with the ATEX directive (Ex nAC IIC T3) the following installation instructions have to be observed. 1. The Series TSP-3PAC power supply units can be installed in Switch cabinets or protective housing that meet the requirements of EN 60079-15 or if applicable EN 60079-0 (housing protection type min. IP54) 2. The permissible ambient temperature range is -25°C to +70°C [-4°F to 158°F]. Observe load derating above an Operating temperature of +55°C [-131°F]. and at a use at Vin = 320Vac – 550Vac. 3. For installation in switch cabinets or in protective housings, it must be ensured that the stipulated maximum temperatures (Ta) are not exceeded on these power supplies. 4. The power supply units are Unit Group II Category 3G components (ex components) as defined by RL 94/9/EG (ATEX 95) Appendix I. A separate conformity on the end-equipment which contains these components evaluation process must be performed. 5. For use / Installation also the requirements defined in EN60079-14 must be observed. ¾ Recycling: The unit contains elements that are suit able for recycling, and components that need special disposal. You are th erefore re quested t o ma ke sure that the power su pply will be recy cled environm ent friendly at the end of its service life. Rev: 1.2 / 5010