SSF2301A 20V P-Channel MOSFET D DESCRIPTION The SSF2301A uses advanced trench technology to provide excellent R DS(ON), low gate charge and operation with gate voltages as low as 2.5V. This device is suitable for use as a load switch or in PWM applications. G S GENERAL FEATURES Schematic Diagram ● V DS = -20V,ID = -4A R DS(ON) < 80mΩ @ VGS=-2.5V R DS(ON) < 65mΩ @ VGS=-4.5V ● High Power and current handing capability ● Lead free product ● Surface Mount Package Marking and Pin Assignment APPLICATIONS ●PWM applications ●Load switch ●Power management SOT23 Top View PACKAGE MARKING AND ORDERING INFORMATION Device Marking Device Device Package Reel Size 2301A SSF2301A SOT23 Ø180mm ABSOLUTE MAXIMUM RATINGS (T A=25℃unless otherwise noted) Parameter Symbol Tape Width Quantity 8 mm 3000 units Limit Unit Drain-Source Voltage V DS -20 V Gate-Source Voltage V GS ±12 V ID -4 A IDM -20 A PD 1.6 W TJ,TSTG -55 To 150 ℃ R θJA 156 ℃/W Drain Current-Continuous@ Current-Pulsed (Note 1) Maximum Power Dissipation Operating Junction and Storage Temperature Range THERMAL CHARACTERISTICS Thermal Resistance,Junction-to-Ambient (Note 2) www.goodark.com Page 1 of 4 Rev.1.0 SSF2301A 20V P-Channel MOSFET ELECTRICAL CHARACTERISTICS (T A=25℃unless otherwise noted) Parameter Symbol Condition Min Typ Max Unit OFF CHARACTERISTICS Drain-Source Breakdown Voltage BV DSS VGS=0V ID=-250μA -20 V Zero Gate Voltage Drain Current IDSS V DS=-20V,VGS=0V -1 μA Gate-Body Leakage Current IGSS VGS=±12V,VDS=0V ±100 nA Gate Threshold Voltage VGS(th) VDS=VGS,ID=-250μA -1 V Drain-Source On-State Resistance RDS(ON) ON CHARACTERISTICS (Note 3) Forward Transconductance g FS -0.5 VGS=-4.5V, ID=-4A 46 65 VGS=-2.5V, ID=-3A 65 80 VDS=-5V,ID=-4A 7 S 640 PF 180 PF mΩ DYNAMIC CHARACTERISTICS (Note4) Input Capacitance C lss V DS=-10V,VGS=0V, F=1.0MHz Output Capacitance Coss Reverse Transfer Capacitance C rss 100 PF Turn-on Delay Time td(on) 27 nS Turn-on Rise Time tr 60 nS 30 nS SWITCHING CHARACTERISTICS (Note 4) Turn-Off Delay Time VDD=-10V,ID=-1A VGS=-4.5V,RGEN=6Ω td(off) Turn-Off Fall Time tf 10 nS Total Gate Charge Qg 9.6 nC Gate-Source Charge Q gs 1.5 nC Gate-Drain Charge Q gd 2.4 nC V DS=-10V,ID=-4A,VGS=-4.5V DRAIN-SOURCE DIODE CHARACTERISTICS Diode Forward Voltage (Note 3) V SD VGS=0V,IS=-1A -1.2 V NOTES: 1. Repetitive Rating: Pulse width limited by maximum junction temperature. 2. Surface Mounted on FR4 Board, t ≤ 10 sec. 3. Pulse Test: Pulse Width ≤ 300μs, Duty Cycle ≤ 2%. 4. Guaranteed by design, not subject to production testing. www.goodark.com Page 2 of 4 Rev.1.0 SSF2301A 20V P-Channel MOSFET TYPICAL ELECTRICAL AND THERMAL CHARACTERISTICS Vdd Vgs Rgen td(on) Rl Vin D ton tr Vout 90% VOUT G toff tf td(off) 90% INVERTED 10% 10% 90% S VIN 50% 50% 10% PULSE WIDTH Figure 2:Switching Waveforms R(t),Normalized Effective Transient Thermal Impedance Figure1:Switching Test Circuit Square Wave Pluse Duration(sec) Figure 3: Normalized Maximum Transient Thermal Impedance www.goodark.com Page 3 of 4 Rev.1.0 SSF2301A 20V P-Channel MOSFET SOT-23 PACKAGE INFORMATION Dimensions in Millimeters (UNIT: mm) Symbol A A1 A2 b c D E E1 e e1 L L1 θ Dimensions in Millimeters MIN. MAX. 0.900 1.150 0.000 0.100 0.900 1.050 0.300 0.500 0.080 0.150 2.800 3.000 1.200 1.400 2.250 2.550 0.950TYP 1.800 2.000 0.550REF 0.300 0.500 0° 8° NOTES 1. All dimensions are in millimeters. 2. Tolerance ±0.10mm (4 mil) unless otherwise specified 3. Package body sizes exclude mold flash and gate burrs. Mold flash at the non-lead sides should be less than 5 mils. 4. Dimension L is measured in gauge plane. 5. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. www.goodark.com Page 4 of 4 Rev.1.0