HIP2060 60V, 10A Half Bridge Power MOSFET Array April 1998 Features Description • Two 10A Power MOS N-Channel Transistors The HIP2060 is a power half-bridge MOSFET array that consists of two matched N-Channel enhancement-mode MOS transistors. The advanced Intersil PASIC2 process technology used in this product utilizes efficient geometries that provides outstanding device performance and ruggedness. • Output Voltage to 60V • rDS(ON) . . . . . 0.135Ω Max Per Transistor at VGS = 15V • rDS(ON) . . . . . . 0.15Ω Max Per Transistor at VGS = 10V The HIP2060 is designed to integrate two power devices in one chip thus providing board layout area and heat sink savings for applications such as Motor Controls, Uninterruptable Power Supplies, Switch Mode Power Supplies, Voice Coil Motors, and Class D Power Amplifier. • Pulsed Current . . . . . . . . . . . . . . . . 25A Each Transistor • Avalanche Energy . . . . . . . . . . 100mJ Each Transistor • Grounded Tab Eliminates Heat Sink Isolation Ordering Information PART NUMBER TEMP. RANGE (oC) PACKAGE Symbol PKG. NO. HIP2060AS1 -40 to 125 5 Ld SIP Z5.067C HIP2060AS2 -40 to 125 5 Ld Gullwing SIP Z5.067A HIP2060AS3 -40 to 125 5 Ld SIP Z5.067B DRAIN1 GATE1 NOTE: When ordering use the entire part number. 5 Z1 D1 1 SOURCE1 = DRAIN2 4 GATE2 Z2 2 SOURCE2 3, TAB Packages JEDEC TS-001AA (ALTERNATE VERSION) HIP2060 AS1 54 3 2 JEDEC MO-169 HIP2060 AS2 1 1 GATE1 2 GATE2 3 SOURCE2 4 SOURCE1-DRAIN2 5 DRAIN1 (TAB) Z5.067B (SIP) HIP2060 AS3 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. http://www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999 1 File Number 3983.5 HIP2060 Absolute Maximum Ratings TC = 25oC, Unless Otherwise Specified HIP2060 60 Continuous Drain-Source Voltage Over Operating Junction and Case Temperature Range. . . . . . VDS UNITS V Drain-Gate Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .VDGR 60 V Gate-Source Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VGS ±20 V Continuous Source-Drain Diode Current (Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ISD 10 A Pulsed Drain Current, each Output, all Outputs on (Notes 1, 2) . . . . . . . . . . . . . . . . . . . . . . . IDM 25 A Continuous Drain Current, each Output, all Outputs on (Note 2) . . . . . . . . . . . . . . . . . . . . . . . .IDS 10 A Single Pulse Avalanche Energy (Note 3) Refer to UIS Curve . . . . . . . . . . . . . . . . . . . . . . . . . EAS 100 mJ Continuous Power Dissipation at TC = 25oC (Infinite Heatsink). . . . . . . . . . . . . . . . . . . . . . . . . PD 46 W Continuous Power Dissipation, Derate above TC = 25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.37 W/oC Thermal Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . θJA 60 oC/W Operating Case Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TC -40 to 125 oC Junction and Storage Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TJ, TSTG -40 to 150 oC Lead Temperature (For Soldering, 10s)(Lead Tips Only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TL 300 oC Continuous Drain1-Source2 Voltage Over Operating Junction Temperature Range. . . . . . VD1S2 60 V NOTES: 1. Pulse width limited by maximum junction temperature. 2. Drain current limited by package construction. 3. VDD = 25V, Start TJ = 25oC, L = 1.5mH, RGS = 50Ω, R = 0. See Figures 2, 12, and 13. Electrical Specifications TC = 25oC, Unless Otherwise Specified PARAMETER Drain-Source Breakdown Voltage SYMBOL BVDSS TEST CONDITIONS ID = 100µA, VGS = 0V TC = -40oC to 125oC TC = 25oC MIN TYP MAX UNITS 60 - - V - 70 - V 1.5 2.3 2.7 V Gate Threshold Voltage VGS(TH) VGS = VDS, ID = 250µA Drain1-Source2 Breakdown Voltage (Across D1) BVD1S2 ID1S2 = 1µA, VG1S1, VG2S2 = 0V TC = 25oC - 105 - V TC = 25oC - - 1 µA Zero Gate Voltage Drain Current IDSS VDS = 60V VGS = 0V Drain1-Source2 Current (Through D1) ID1S2 VD1S2 = 60V TC = 25oC VG1S1 = 0V, VG2S2 = 0V TC = 125oC - 0.3 1 µA - 1 - µA ID = 10A, VGS = 15V - 0.9 1.25 V ID = 10A, VGS = 10V - 1.1 1.5 V Drain-Source On-State Voltage (Note 4) VDS(ON) Forward Gate Current, Drain Short Circuited to Source IGSSF VDS = 0V, VGS = 20V - - 100 nA Reverse Gate Current, Drain Short Circuited to Source IGSSR VDS = 0V, VGS = -20V - - -100 nA Drain-Source On Resistance (Note 4) Forward Transconductance (Note 4) rDS(ON) gfs VGS = 15V, ID = 10A TC = 25oC - 0.09 0.135 Ω VGS = 15V, ID = 10A TC = 125oC - 0.15 0.21 Ω VGS = 10V, ID = 10A TC = 25oC - 0.11 0.15 Ω VGS = 10V, ID = 10A TC = 125oC - 0.19 0.25 Ω - 4.5 - S VDS = 15V, ID = 5A 2 HIP2060 Electrical Specifications TC = 25oC, Unless Otherwise Specified (Continued) PARAMETER Turn-On Delay Time (Note 5) SYMBOL MIN TYP MAX UNITS - 4 - ns - 5 - ns td(OFF) - 12 - ns tf - 6 - ns - 10.5 12.0 nC td(ON) Rise Time (Note 5) Turn-Off Delay Time (Note 5) tr Fall Time (Note 5) Total Gate Charge (Note 5) Qg(TOT) TEST CONDITIONS VDD = 30V, RL = 3Ω ID = 10A, VGS = 10V, RG = 50Ω See Figure 14 VDS = 50V, VGS = 10V, ID = 10A See Figures 16 and 17 Gate-Source Charge (Note 5) Qgs - 1.4 2.0 nC Gate-Drain Charge (Note 5) Qgd - 4.9 5.5 nC Short-Circuit Input Capacitance, Common Source CISS - 230 - pF VDS = 25V, VGS = 0V, f = 1MHz Short-Circuit Output Capacitance, Common Source for Upper FET COSS(U) - 150 - pF Short Circuit Output Capacitance Common Source for Lower FET COSS(L) - 225 - pF Short-Circuit Reverse Transfer Capacitance, Common Source CRSS - 40 - pF Thermal Resistance Junction to Case RθJC - - 2.7 oC/W Thermal Resistance Junction to Ambient RθJA - - 60 oC/W MIN TYP MAX UNITS ISD = 10A, VGS = 0V - 1.05 1.25 V Source-Drain Diode Specifications PARAMETER SYMBOL TEST CONDITIONS SOURCE-TO-DRAIN DIODE SPECIFICATIONS (Across Z1 and Z2) Forward Voltage (Note 4) VSD Reverse Recovery Time (Across Z1) trr(S1-D1) ISD = 10A, dISD/dt = 100A/µs - 50 - ns Reverse Recovery Time (Across Z2) trr(S2-D2) ISD = 10A, dISD/dt = 100A/µs - 75 - ns ISD = 10A, VGS = 0V - 8.5 9.5 V ISD = 10A, dISD/dt = 100A/µs - 200 - ns VGS = 10V, ID = 10A, TC = 25oC - 90 - % SOURCE2-TO-DRAIN1 DIODE SPECIFICATIONS D (Across D1) Forward Voltage (Note 4) VSD Reverse Recovery Time trr DEVICE MATCHING Drain-Source On Resistance Match rDS(ON)M NOTES: 4. Pulse test: Pulse Width ≤ 300µs, Duty Cycle ≤ 2%. 5. Independent of operating temperature. 3 HIP2060 Typical Performance Curves 50 TC = 25oC IAS, AVALANCHE CURRENT (A) ID, DRAIN CURRENT (A) 50 10µs 10 100µs 10 5 1ms OPERATION IN THIS AREA MAY BE LIMITED BY rDS(ON) 1 10ms STARTING TC = 125oC 5 DC 0.5 5 10 50 VDS, DRAIN-TO-SOURCE VOLTAGE (V) 1 STARTING TC = 25oC 1 0.001 100 0.01 0.1 tAV, TIME IN AVALANCHE (ms) FIGURE 2. UNCLAMPED INDUCTIVE-SWITCHING FIGURE 1. SAFE-OPERATING AREA CURVE 20 20 25oC -40oC VGS = 15V VGS = 12V VDS = 15V VGS = 10V 15 ID, DRAIN CURRENT (A) ID, DRAIN CURRENT (A) 1 VGS = 8V 10 5 PULSE DURATION = 300µs, TC = 25oC 0 0 2 4 6 8 15 150oC 10 5 0 0 10 VDS, DRAIN-TO-SOURCE VOLTAGE (V) 2 4 6 8 10 VGS, GATE-TO-SOURCE VOLTAGE (V) FIGURE 3. SATURATION CHARACTERISTICS FIGURE 4. TRANSFER CHARACTERISTICS 2.5 1.2 PULSE DURATION = 300µs, VGS = 10V, ID = 10A ID = 100µA NORMALIZED BVDSS NORMALIZED rDS(ON) 2.0 1.5 1.0 1.1 1.0 0.9 0.5 0 -75 -25 25 75 125 0.8 -75 175 TJ, JUNCTION TEMPERATURE (oC) -25 25 75 125 175 TJ, JUNCTION TEMPERATURE (oC) FIGURE 5. NORMALIZED rDS(ON) vs JUNCTION TEMPERATURE FIGURE 6. NORMALIZED BVDSS vs JUNCTION TEMPERATURE 4 HIP2060 Typical Performance Curves (Continued) 16 2.0 VGS, GATE-SOURCE VOLTAGE (V) NORMALIZED VGS(TH) VGS = VDS, ID = 250µA 1.5 1.0 0.5 0 -75 VDS = 50V VDS = 30V VDS = 20V 12 ID = 10A, TC = 25oC 8 4 0 -25 25 75 125 175 0 5 TJ, JUNCTION TEMPERATURE (oC) 10 ID, DRAIN CURRENT (A) CRSS 600 COSS(U) COSS(L) 400 CISS 200 VGS = 15V VGS = 10V 8 6 4 2 0 5 10 15 20 0 25 25 50 VDS, DRAIN-TO-SOURCE VOLTAGE (V) FIGURE 9. CAPACITANCE vs VOLTAGE ZθJC, NORMALIZED THERMAL RESPONSE C, CAPACITANCE (pF) 20 12 VGS = 0V, f = 1MHz, TC = 25oC 800 0 15 FIGURE 8. GATE-SOURCE VOLTAGE vs GATE CHARGE FIGURE 7. NORMALIZED VGS(TH) vs JUNCTION TEMPERATURE 1000 10 Q, GATE CHARGE (nC) TC = 25oC D = 1.0 0.5 0.2 0.1 0.1 0.05 0.02 0.01 SINGLE PULSE 0.01 10-5 150 FIGURE 10. MAXIMUM CONTINUOUS DRAIN CURRENT vs CASE TEMPERATURE 10 1 75 100 125 TC, CASE TEMPERATURE (oC) NOTES: 1. DUTY FACTOR, D = t1/t2 2. PEAK TJ = PDM x (ZθJC) +TC 10-3 10-1 10-4 10-2 10o t1, RECTANGULAR PULSE DURATION (s) 101 FIGURE 11. NORMALIZED MAXIMUM TRANSIENT THERMAL IMPEDANCE 5 HIP2060 Test Circuits and Waveforms tP VDS 10V VGS L RG tAV 0 IAS + DUT - VGS VDD ID tP 0V ID 0 BVDSS VDS 0.01Ω 0 FIGURE 12. UNCLAMPED ENERGY TEST CIRCUIT FIGURE 13. UNCLAMPED ENERGY WAVEFORMS tON VDD tOFF td(ON) td(OFF) tr VDS RL tf 90% 90% VDS VGS 10% 10% DUT 90% 0V RGS 50% VGS 50% PULSE WIDTH 10% FIGURE 14. RESISTIVE SWITCHING TEST CIRCUIT FIGURE 15. RESISTIVE SWITCHING WAVEFORMS +VDS CURRENT REGULATOR QG SAME TYPE AS DUT 10V + 15V BATTERY 0.2µF 25kΩ - 0.1µF QGS VG DUT 0 QGD IGS CHARGE FIGURE 16. GATE CHARGE TEST CIRCUIT FIGURE 17. BASIC GATE CHARGE WAVEFORM 6 HIP2060 1µF 0.22µF 0.22µF UF 4002 RL = 8Ω 30µH +36V 0.47µF 3.9Ω 0.22µF +12V BHB BHO HEN BHS DIS BLO VSS BLS OUT VDD IN+ VCC IN- ALS HDEL ALO LDEL AHS AHB AHO 10Ω 30µH 1µF 10Ω HIP2060 +12V HIP2060 10Ω 10Ω HIP4080A 100Ω 0.1Ω ILIM 100kΩ UF 4002 100kΩ 0.22µF 0.001µF 0.22µF ∑ + FEEDBACK + AUDIO INPUT 250kHz FIGURE 18. 70W SWITCHING AUDIO AMPLIFIER APPLICATION CIRCUIT Device Model Netlist for HIP2060 Half Bridge Power MOSFET Array .SUBCKT HIP2060 1 2 3 4 5 X1 6 1 7 3 HIP2060_1 LS1 5 6 7.5n X2 7 2 8 3 HIP2060_1 LS2 7 4 7.5n LS3 8 3 7.5n .ENDS .SUBCKT HIP2060_1 3 2 11 9 MOS1 4 2 1 1 NMOS1 JFET 10 1 4 J1 D1 5 6 D1 DBODY 1 10 D2 DBREAK 10 7 D3 DSUB 9 3 D4 VBREAK 7 1 DC 90 C21 2 1 850P C23 2 10 50P C24 2 4 1350P RDRAIN 3 10 1.5e-03 RSOURCE 1 11 17.5e-03 FDSCHRG 4 2 VMEAS 1.0 E41 5 11 4 1 1.0 VPINCH 6 8 DC 10.0 VMEAS 8 11 DC 0.0 .MODEL NMOS1 NMOS LEVEL=3 (VTO=2.75 TOX=5e-08 KP=3.150e-03 PHI=0.65 GAMMA=2.55 + VMAX=6.42e+07 NSUB=4.33e+16 THETA=0.60973 ETA=0.0015 KAPPA=1.275 L=1u W=5950u) .MODEL J1 NJF (VTO=-15.0 BETA=10.736 LAMBDA=1.15e-02 P1.MODEL D1 D (IS=1.0e-15 N=0.03 RS=1.0) .MODEL D2 D (IS=3.0e-13 RS=2.5e-03 TT=20N CJO=350e-12) .MODEL D3 D (IS=1.0e-13 N=1.0 RS=2.0) .MODEL D4 D (IS=1.0e-13 RS=2.0e-03 CJO=197e-12) .ENDS NOTE: For further discussion of the PSPICE PowerFET Macromodel consult “Spicing-up SPICE II Software for Power MOSFET Modeling”, Intersil Application Note AN8610. 7 HIP2060 All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site http://www.intersil.com Sales Office Headquarters NORTH AMERICA Intersil Corporation P. O. Box 883, Mail Stop 53-204 Melbourne, FL 32902 TEL: (407) 724-7000 FAX: (407) 724-7240 EUROPE Intersil SA Mercure Center 100, Rue de la Fusee 1130 Brussels, Belgium TEL: (32) 2.724.2111 FAX: (32) 2.724.22.05 8 ASIA Intersil (Taiwan) Ltd. Taiwan Limited 7F-6, No. 101 Fu Hsing North Road Taipei, Taiwan Republic of China TEL: (886) 2 2716 9310 FAX: (886) 2 2715 3029