TOSHIBA TPD4113AK

TPD4113AK
TOSHIBA Intelligent Power Device
High Voltage Monolithic Silicon Power IC
TPD4113AK
The TPD4113AK is a DC brush less motor driver using
high- voltage PWM control. It is fabricated using a high-voltage
SOI process. The device contains a level shift high side driver,
low side driver, IGBT outputs, FRDs and protective functions for
under-voltage protection circuits, and a thermal shutdown circuit.
It is easy to control a DC brush less motor by just putting logic
inputs from a MPU or motor controller to the TPD4113AK.
Features
•
Bootstrap circuit gives simple high-side power supply.
•
Bootstrap diodes are built in.
•
A dead time can be set as a minimum of 1.4 μs, and it is the
best for a Sine-wave from drive.
•
3-phase bridge output using IGBTs.
•
FRDs are built in.
•
Included under-voltage protection and thermal shutdown.
•
The regulator of 7V (typ.) is built in.
•
Package: 23-pin HZIP.
This product has a MOS structure and is sensitive to electrostatic
discharge. When handling this product, ensure that the environment
is protected against electrostatic discharge.
Weight
HZIP23-P-1.27F : 6.1 g (typ.)
HZIP23-P-1.27G : 6.1 g (typ.)
HZIP23-P-1.27H : 6.1 g (typ.)
1
2006-11-01
TPD4113AK
Pin Assignment
1
HU
2
3
HV HW
4
LU
5
LV
6
LW
7
IS1
8
9
10 11 12 13 14 15 16 17
NC BSU U VBB 1 BSV V BSW W VBB 2 NC
18 19 20 21 22 23
IS2 NC DIAG VCC GND VREG
Marking
Lot No.
TPD4113AK
JAPAN
Part No. (or abbreviation code)
A line indicates
lead (Pb)-free package or
lead (Pb)-free finish.
2
2006-11-01
TPD4113AK
Block Diagram
VCC 21
9 BSU
12 BSV
14 BSW
VREG 23
7V
Regulator
UnderUnderUndervoltage
voltage
voltage
Protection Protection Protection
Undervoltage
Protection
HU 1
HV 2
HW 3
Input Control
LV 5
16 VBB2
High-side Level
Shift Drver
Thermal
10 U
Shutdown
13 V
LU 4
LW 6
11 VBB1
15 W
Low-side
Driver
DIAG 20
18 IS2
7 IS1
22 GND
3
2006-11-01
TPD4113AK
Pin Description
Pin No.
Symbol
Pin Description
1
HU
2
HV
3
HW
4
LU
5
LV
6
LW
7
IS1
IGBT emitter and FRD anode pin.
8
NC
Unused pin, which is not connected to the chip internally.
9
BSU
10
U
11
VBB1
U and V-phase high-voltage power supply input pin.
12
BSV
V-phase bootstrap capacitor connecting pin.
13
V
14
BSW
The control terminal of IGBT by the side of U top arm. It turns off more than by 1.5V.
It turns on more than by 3.5V.
The control terminal of IGBT by the side of V top arm. It turns off more than by 1.5V.
It turns on more than by 3.5V.
The control terminal of IGBT by the side of W top arm. It turns off more than by 1.5V.
It turns on more than by 3.5V.
The control terminal of IGBT by the side of U bottom arm. It turns off more than by 1.5V.
It turns on more than by 3.5V.
The control terminal of IGBT by the side of V bottom arm. It turns off more than by 1.5V.
It turns on more than by 3.5V.
The control terminal of IGBT by the side of W bottom arm. It turns off more than by 1.5V.
It turns on more than by 3.5V.
U-phase bootstrap capacitor connecting pin.
U-phase output pin.
V-phase output pin.
W-phase bootstrap capacitor connecting pin.
15
W
16
VBB2
17
NC
Unused pin, which is not connected to the chip internally.
18
IS2
IGBT emitter and FRD anode pin.
19
NC
Unused pin, which is not connected to the chip internally.
20
Ｗ-phase output pin.
W-phase high-voltage power supply input pin.
DIAG
With the diagnostic output terminal of open drain , a pull-up is carried out by resistance.
It turns it on at the time of unusual.
21
VCC
Control power supply pin.(15V typ.)
22
GND
Ground pin.
23
VREG
7V regulator output pin.
4
2006-11-01
TPD4113AK
Equivalent Circuit of Input Pins
Internal circuit diagram of HU, HV, HW, LU, LV, LW input pins
5 kΩ
5 kΩ
200 kΩ
HU/HV/HW
LU/LV/LW
2 kΩ
To internal circuit
6.5 V
6.5 V
6.5 V
6.5 V
Internal circuit diagram of DIAG pin
DIAG
To internal circuit
26 V
5
2006-11-01
TPD4113AK
Timing Chart
HU
HV
HW
Input Voltage
LU
LV
LW
VU
Output voltage
VV
VW
6
2006-11-01
TPD4113AK
Truth Table
Mode
Input
Top arm
ＨＵ ＨＶ ＨＷ ＬＵ ＬＶ ＬＷ
Normal
Thermal shutdown
Under-voltage
Notes:
Ｕ
Bottom arm
Ｖ
Ｗ
Ｕ
Ｖ
DIAG
Ｗ
phase
phase
phase
phase
phase
phase
Ｈ
Ｌ
Ｌ
Ｌ
Ｈ
Ｌ
ＯＮ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＮ
ＯＦＦ
ＯＦＦ
Ｈ
Ｌ
Ｌ
Ｌ
Ｌ
Ｈ
ＯＮ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＮ
ＯＦＦ
Ｌ
Ｈ
Ｌ
Ｌ
Ｌ
Ｈ
ＯＦＦ
ＯＮ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＮ
ＯＦＦ
Ｌ
Ｈ
Ｌ
Ｈ
Ｌ
Ｌ
ＯＦＦ
ＯＮ
ＯＦＦ
ＯＮ
ＯＦＦ
ＯＦＦ
ＯＦＦ
Ｌ
Ｌ
Ｈ
Ｈ
Ｌ
Ｌ
ＯＦＦ
ＯＦＦ
ＯＮ
ＯＮ
ＯＦＦ
ＯＦＦ
ＯＦＦ
Ｌ
Ｌ
Ｈ
Ｌ
Ｈ
Ｌ
ＯＦＦ
ＯＦＦ
ＯＮ
ＯＦＦ
ＯＮ
ＯＦＦ
ＯＦＦ
Ｈ
Ｌ
Ｌ
Ｌ
Ｈ
Ｌ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＮ
Ｈ
Ｌ
Ｌ
Ｌ
Ｌ
Ｈ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＮ
Ｌ
Ｈ
Ｌ
Ｌ
Ｌ
Ｈ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＮ
Ｌ
Ｈ
Ｌ
Ｈ
Ｌ
Ｌ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＮ
Ｌ
Ｌ
Ｈ
Ｈ
Ｌ
Ｌ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＮ
Ｌ
Ｌ
Ｈ
Ｌ
Ｈ
Ｌ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＮ
Ｈ
Ｌ
Ｌ
Ｌ
Ｈ
Ｌ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＮ
Ｈ
Ｌ
Ｌ
Ｌ
Ｌ
Ｈ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＮ
Ｌ
Ｈ
Ｌ
Ｌ
Ｌ
Ｈ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＮ
Ｌ
Ｈ
Ｌ
Ｈ
Ｌ
Ｌ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＮ
Ｌ
Ｌ
Ｈ
Ｈ
Ｌ
Ｌ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＮ
Ｌ
Ｌ
Ｈ
Ｌ
Ｈ
Ｌ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＦＦ
ＯＮ
Release of Thermal shutdown protection and under voltage protection depends release of a self-reset .
Absolute Maximum Ratings (Ta = 25°C)
Characteristics
Power supply voltage
Symbol
Rating
Unit
VBB
500
V
VCC
18
V
Output current (DC)
Iout
1
A
Output current (pulse)
Iout
2
A
Input voltage
VIN
−0.5~7
V
VREG current
IREG
50
mA
VDIAGcurrent
IDIAG
20
mA
Power dissipation (Ta = 25°C)
PC
4
W
Power dissipation (Tc = 25°C)
PC
20
W
Tjopr
−20~135
°C
Junction temperature
Tj
150
°C
Storage temperature
Tstg
−55~150
°C
Lead-heat sink isolation voltage
Vhs
1000 (1 min)
Vrms
Operating temperature
Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the
significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even
if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum
ratings and the operating ranges.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook
(“Handling Precautions”/Derating Concept and Methods) and individual reliability data (i.e. reliability test report
and estimated failure rate, etc).
7
2006-11-01
TPD4113AK
Electrical Characteristics (Ta = 25°C)
Characteristics
Operating power supply voltage
Symbol
Test Condition
Min
Typ.
Max
VBB
⎯
50
280
450
VCC
⎯
13.5
15
16.5
Unit
V
IBB
VBB = 450 V
⎯
⎯
0.5
ICC
VCC = 15 V
⎯
1.1
5
IBS (ON)
VBS = 15 V, high side ON
⎯
260
410
IBS (OFF)
VBS = 15 V, high side OFF
⎯
230
370
VIH
VIN = “H”
3.5
⎯
⎯
VIL
VIN = “L”
⎯
⎯
1.5
IIH
VIN = 5Ｖ
⎯
⎯
150
IIL
VIN = 0 V
⎯
⎯
100
VCEsatH
VCC = 15 V, IC = 0.5 A
⎯
2.4
3
VCEsatL
VCC = 15 V, IC = 0.5 A
⎯
2.4
3
VFH
IF = 0.5 A, high side
⎯
1.6
2.0
VFL
IF = 0.5 A, low side
⎯
1.6
2.0
VCC = 15 V, IO = 30 mA
6.5
7
7.5
V
VF (BSD)
IF = 500μＡ
⎯
0.9
1.2
V
TSD
VCC = 15 V
135
⎯
185
℃
Thermal shutdown hysteresis
ΔTSD
VCC = 15 V
⎯
50
⎯
℃
VCC under-voltage protection
VCCUVD
⎯
10
11
12
V
VCC under-voltage protection recovery
VCCUVR
⎯
10.5
11.5
12.5
V
VBS under-voltage protection
VBSUVD
⎯
8
9
9.5
V
VBS under-voltage protection recovery
VBSUVR
⎯
8.5
9.5
10.5
V
DIAG saturation voltage
VDIAGsat
IDIAG=5mA
⎯
⎯
0.5
V
Current dissipation
Input voltage
Input current
Output saturation voltage
FRD forward voltage
Regulator voltage
BSD forward voltage
Thermal shutdown temperature
VREG
mA
μA
V
μA
V
V
Output-on delay time
ton
VBB = 280 V, IC = 0.5 A
⎯
1.5
3
μs
Output-off delay time
toff
VBB = 280 V, IC = 0.5 A
⎯
1.2
3
μs
tdead
VBB = 280 V, IC = 0.5 A
1.4
⎯
⎯
μs
trr
VBB = 280 V, IC = 0.5 A
⎯
200
⎯
ns
Dead time
FRD reverse recovery time
8
2006-11-01
TPD4113AK
Application Circuit Example
15V
VCC
21
+
C4
9
12
C5
14
C6+
C7
VREG
23
7V
Regulator
11
UnderUnderUndervoltage
voltage
voltage
Protection Protection Protection
Undervoltage
Protection
HU
Control IC
HV
or
HW
Microcomputer
LU
LV
LW
R２
1
16
Thermal
10
Shutdown
13
6
BSW
VBB1
VBB2
C1 C2 C3
3
5
BSV
High-side
Level Shift
Driver
2
4
BSU
Input Control
15
U
Ｍ
V
W
Low-side
Driver
20
DIAG
18
7
IS2
IS1
22
9
R１
GND
2006-11-01
TPD4113AK
External Parts
Standard external parts are shown in the following table.
Part
Recommended Value
Purpose
Remarks
C1, C2, C3
25 V/2.2 μF
Bootstrap capacitor
(Note 1)
R1
0.62 Ω ± 1% (1 W)
Current detection
(Note 2)
C4
25 V/10 μF
VCC power supply stability
(Note 3)
C５
25 V/0.1 μF
VCC for surge absorber
(Note 3)
C6
16 V/1 μF
VREG power supply stability
(Note 3)
C7
16 V/1000 pF
VREG for surge absorber
(Note 3)
R2
5.1 kΩ
DIAG pin pull-up resistor
(Note 4)
Note 1: The required bootstrap capacitance value varies according to the motor drive conditions. The capacitor is
biased by VCC and must be sufficiently derated for it.
Note 2: The following formula shows the detection current: IO = VR ÷ R1
Do not exceed a detection current of 1A when using this product.
(Please go from the outside in the over current protection.)
Note 3: When using this product, some adjustment is required in accordance with the use environment. When
mounting, place as close to the base of this product leads as possible to improve the ripple and noise
elimination.
Note 4: The DIAG pin is open drain. Note that when the DIAG pin is connected to a power supply with a voltage
higher than or equal to the VCC, a protection circuit is triggered so that the current flows continuously. If the
DIAG pin is not used, connect to the GND.
Handling precautions
(1)
(2)
Please control the input signal in the state to which the VCC voltage is steady. Both of the order of
the VBB power supply and the VCC power supply are not cared about either.
Note that if the power supply is switched off as described above, this product may be destroyed if the
current regeneration route to the VBB power supply is blocked when the VBB line is disconnected by
a relay or similar while the motor is still running.
The excess voltage such as the voltage serge which exceed the maximum rating is added, for example,
may destroy the circuit. Accordingly, be careful of handling this product or of surge voltage in its
application environment.
10
2006-11-01
TPD4113AK
Description of Protection Function
(1)
Under-voltage protection
This product incorporates an under-voltage protection circuit to prevent the IGBT from operating in
unsaturated mode when the VCC voltage or the VBS voltage drops.
When the VCC power supply falls to this product internal setting (VCCUVD = 11 V typ.), all IGBT
outputs shut down regardless of the input. This protection function has hysteresis. When the
VCCUVR (= 11.5 V typ.) reaches 0.5 V higher than the shutdown voltage, this product is
automatically restored and the IGBT is turned on/off again by the input.
When the VBS supply voltage drops (VBSUVD = 9 V typ.), the high-side IGBT output shuts down.
When the VBSUVR (= 9.5 V typ.) reaches 0.5 V higher than the shutdown voltage, the IGBT is
turned on/off again by the input signal.
Thermal shutdown
This product incorporates a thermal shutdown circuit to protect itself against excessive rise in
temperature.When the temperature of this chip rises to the internal setting TSD due to external
causes or internal heat generation all IGBT outputs shut down regardless of the input. This
protection function has hysteresis (ΔTSD = 50°C typ.). When the chip temperature falls to TSD −
ΔTSD, the chip is automatically restored and the IGBT is turned on/off again by the input.
Because the chip contains just one temperature-detection location, when the chip heats up due to the
IGBT, for example, the differences in distance between the detection location and the IGBT (the
source of the heat) can cause differences in the time taken for shutdown to occur. Therefore, the
temperature of the chip may rise higher than the initial thermal shutdown temperature.
(2)
(A)
0.9
0.83
0
1.0
0.9
Peak winding current
Peak winding current
(A)
Safe Operating Area
0
400
Power supply voltage
Figure 1
VBB
0
450
(V)
0
400
Power supply voltage
SOA at Tj = 135°C
Figure 2
VBB
450
(V)
SOA at Tc = 95°C
Note 1: The above safe operating areas are at Tj = 135°C (Figure 1) and Tc = 95°C (Figure 2). If the temperature
exceeds these, the safe operation areas reduce.
Note 2:
The above safe operating areas include the over current protection operation area.
11
2006-11-01
TPD4113AK
VCEsatL – Tj
3.6
VCC = 15 V
IGBT saturation voltage VCEsatL (V)
IGBT
saturation voltage VCEsatH
(V)
VCEsatH – Tj
3.6
IC = 700 mA
3.2
2.8
IC = 500 mA
2.4
IC = 300 mA
2.0
1.6
−20
20
60
Junction temperature
100
Tj
VCC = 15 V
2.8
IC = 500 mA
2.4
IC = 300 mA
2.0
1.6
−20
140
IC = 700 mA
3.2
(°C)
20
60
Junction temperature
1.6
IF = 700 mA
1.4
IF = 500 mA
IF = 300 mA
1.2
1.0
0.8
−20
20
60
Junction temperature
100
Tj
1.6
IF = 500 mA
IF = 300 mA
1.2
1.0
(°C)
20
60
Junction temperature
ICC – VCC
(mA)
25°C
Regulator voltage VREG (V)
ICC
Tj
140
(°C)
−20°C
25°C
135°C
−20°C
Consumption current
100
VREG – VCC
8.0
135°C
1.5
1.0
0.5
14
(°C)
IF = 700 mA
1.4
0.8
−20
140
2.0
0
12
Tj
140
VFL – Tj
FRD forward voltage VFL (V)
FRD forward voltage VFH
(V)
VFH – Tj
100
16
Control power supply voltage
(V)
Ireg = 30 mA
7.0
6.5
6.0
12
18
VCC
7.5
14
16
Control power supply voltage
12
18
VCC
(V)
2006-11-01
TPD4113AK
tON – Tj
tOFF – Tj
3.0
tOFF
2.0
1.0
Output-off delay time
Output-on delay time
tON
(μs)
(μs)
3.0
VBB = 280 V
VCC = 15 V
IC = 0.5 A
High-side
Low-side
0
−20
20
60
Junction temperature
100
Tj
VBB = 280 V
VCC = 15 V
IC = 0.5 A
High-side
Low-side
2.0
1.0
0
−20
140
(°C)
20
Junction temperature
VCCUV– Tj
Tj
140
(°C)
10.5
VCCUVD
Under-voltage protection operating
voltage VBSUV (V)
Under-voltage protection operating
voltage VCCUV (V)
100
VBSUV – Tj
12.5
VCCUVR
12.0
11.5
11.0
10.5
10.0
−20
60
20
60
Junction temperature
100
Tj
VBSUVD
VBSUVR
10.0
9.5
9.0
8.5
8.0
−20
140
(°C)
20
60
Junction temperature
13
100
Tj
140
(°C)
2006-11-01
TPD4113AK
IBS – VBS (ON)
IBS – VBS (OFF)
500
IBS （OFF)
−20°C
25°C
135°C
400
Current consumption
( A)
Current consumption
IBS (ON) (μA)
500
300
200
100
12
14
16
Control power supply Voltage
400
300
200
100
12
18
VBS
−20°C
25°C
135°C
(V)
14
16
Control power supply Voltage
18
VBS
(V)
Wton – Tj
VF (BSD) – Tj
(V)
250
(μJ)
Wton
0.9
Turn-on loss
BSD forward voltage
VF（BSD）
1.0
IF = 700 μA
0.8
IF = 500 μA
0.7
200
150
IC = 700 mA
IC = 500 mA
100
IC = 300 mA
50
IF = 300 μA
0.6
−20
20
60
Junction temperature
100
Tj
0
−20
140
20
60
Junction temperature
(°C)
100
Tj
140
(°C)
Wtoff – Tj
(μJ)
30
Turn-*off loss
40
Wtoff
50
IC = 700 mA
20
IC = 500 mA
10
0
−20
IC = 300 mA
20
60
Junction temperature
100
Tj
140
(°C)
14
2006-11-01
0.5A
15
23. VREG
22. GND
21. Vcc
20. DIAG
19. NC
18. IS2
17. NC
16. VBB2
15. W
14. BSW
13. V
12. BSV
11. VBB1
10. U
9. BSU
8. NC
7. IS1
6. LW
5. LV
4. LU
3. HW
2. HV
1. HU
0.5A
23. VREG
22. GND
21. Vcc
20. DIAG
19. NC
18. IS2
17. NC
16. VBB2
15. W
14. BSW
13. V
12. BSV
11. VBB1
10. U
9. BSU
8. NC
7. IS1
6. LW
5. LV
4. LU
3. HW
2. HV
1. HU
TPD4113AK
Test Circuits
IGBT Saturation Voltage (U-phase low side)
HU = 0 V
HV = 0 V
HW = 0 V
LU = 5 V
LV = 0 V
LW = 0 V
VM
VCC = 15 V
FRD Forward Voltage (U-phase low side)
VM
2006-11-01
16
30 mA
23. VREG
22. GND
21. Vcc
20. DIAG
19. NC
18. IS2
17. NC
16. VBB2
15. W
14. BSW
13. V
12. BSV
11. VBB1
10. U
9. BSU
8. NC
7. IS1
6. LW
5. LV
4. LU
3. HW
2. HV
1. HU
23. VREG
22. GND
21. Vcc
20. DIAG
19. NC
18. IS2
17. NC
16. VBB2
15. W
14. BSW
13. V
12. BSV
11. VBB1
10. U
9. BSU
8. NC
7. IS1
6. LW
5. LV
4. LU
3. HW
2. HV
1. HU
TPD4113AK
VCC Current Dissipation
IM
VCC = 15 V
Regulator Voltage
VM
VCC = 15 V
2006-11-01
TPD4113AK
560 Ω
23. VREG
22. GND
21. Vcc
20. DIAG
19. NC
18. IS2
17. NC
16. VBB2
15. W
14. BSW
13. V
12. BSV
11. VBB1
10. U
9. BSU
8. NC
2.2 μF
7. IS1
6. LW
5. LV
4. LU
3. HW
2. HV
1. HU
Output ON/OFF Delay Time (U-phase low side)
HU = 0 V
HV = 0 V
HW = 0 V
LU =
PG
LV = 0 V
LW = 0 V
VCC = 15 V
U = 280 V
IM
90%
LU
10%
90%
IM
10%
tON
tOFF
17
2006-11-01
TPD4113AK
23. VREG
22. GND
21. Vcc
20. DIAG
19. NC
18. IS2
17. NC
16. VBB2
15. W
14. BSW
13. V
12. BSV
11. VBB1
10. U
9. BSU
2 kΩ
8. NC
7. IS1
6. LW
5. LV
4. LU
3. HW
2. HV
1. HU
VCC Under-voltage Protection Operation/Recovery Voltage (U-phase low side)
HU = 0 V
HV = 0 V
HW = 0 V
LU = 5 V
LV = 0 V
LW = 0 V
VCC = 15 V → 6 V
6 V → 15 V
U = 18 V
VM
*:Note:Sweeps the VCC pin voltage from 15 V and monitors the U pin voltage.
The VCC pin voltage when output is off defines the under voltage protection operating voltage.
Also sweeps from 6 V to increase. The VCC pin voltage when output is on defines the under voltage protection
recovery voltage.
23. VREG
22. GND
21. Vcc
20. DIAG
19. NC
18. IS2
17. NC
16. VBB2
15. W
2 kΩ
VM
14. BSW
13. V
12. BSV
11. VBB1
10. U
9. BSU
8. NC
7. IS1
6. LW
5. LV
4. LU
3. HW
2. HV
1. HU
VBS Under-voltage Protection Operation/Recovery Voltage (U-phase high side)
HU = 5 V
HV = 0 V
HW = 0 V
LU = 0 V
LV = 0 V
LW = 0 V
VCC = 15 V
VBB = 18 V
BSU = 15 V → 6 V
6 V → 15 V
*:Note: Sweeps the BSU pin voltage from 15 V and monitors the VBB pin voltage.
The BSU pin voltage when output is off defines the under-voltage protection operating voltage.
Also sweeps the BSU pin voltage from 6 V and changes from the HU pin voltage at 0 V → 5 V → 0 V.
The BSU pin voltage when output is on defines the under-voltage protection recovery voltage.
18
2006-11-01
IM
19
23. VREG
22. GND
21. Vcc
20. DIAG
19. NC
18. IS2
17. NC
16. VBB2
15. W
14. BSW
13. V
12. BSV
11. VBB1
10. U
9. BSU
8. NC
7. IS1
6. LW
5. LV
4. LU
3. HW
2. HV
1. HU
TPD4113AK
VBS Current Consumption (U-phase high side)
HU = 0 V/ 5 V
HV = 0 V
HW = 0 V
LU = 0 V
LV = 0 V
LW = 0 V
VCC = 15 V
BSU = 15 V
2006-11-01
TPD4113AK
VM
L
23. VREG
22. GND
21. Vcc
20. DIAG
19. NC
18. IS2
17. NC
15. W
14. BSW
13. V
12. BSV
11. VBB1
10. U
9. BSU
8. NC
2.2 μF
7. IS1
6. LW
5. LV
4. LU
3. HW
2. HV
1. HU
Turn-On/Off Loss (low-side IGBT + high-side FRD)
HU = 0 V
HV = 0 V
HW = 0 V
LU=
PG
LV = 0 V
LW = 0 V
VCC = 15 V
VBB/U = 280 V
IM
5 mH
Input (HU)
IGBT (C-E voltage)
(U-GND)
Power supply current
Wtoff
Wton
20
2006-11-01
TPD4113AK
Package Dimensions
Weight: 6.1 g (typ.)
21
2006-11-01
TPD4113AK
Package Dimensions
Weight: 6.1 g (typ.)
22
2006-11-01
TPD4113AK
Package Dimensions
Weight: 6.1 g (typ.)
23
2006-11-01
TPD4113AK
RESTRICTIONS ON PRODUCT USE
20070701-EN
• The information contained herein is subject to change without notice.
• TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor
devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical
stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of
safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of
such TOSHIBA products could cause loss of human life, bodily injury or damage to property.
In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as
set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and
conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability
Handbook” etc.
• The TOSHIBA products listed in this document are intended for usage in general electronics applications
(computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances,
etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires
extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or
bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or
spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments,
medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his
document shall be made at the customer’s own risk.
• The products described in this document shall not be used or embedded to any downstream products of which
manufacture, use and/or sale are prohibited under any applicable laws and regulations.
• The information contained herein is presented only as a guide for the applications of our products. No
responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which
may result from its use. No license is granted by implication or otherwise under any patents or other rights of
TOSHIBA or the third parties.
• Please contact your sales representative for product-by-product details in this document regarding RoHS
compatibility. Please use these products in this document in compliance with all applicable laws and regulations
that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses
occurring as a result of noncompliance with applicable laws and regulations.
24
2006-11-01