ONSEMI MBR40H100WTG

MBR40H100WT
SWITCHMODE™
Power Rectifier
100 V, 40 A
Features and Benefits
•
•
•
•
•
•
http://onsemi.com
Low Forward Voltage
Low Power Loss/High Efficiency
High Surge Capacity
175°C Operating Junction Temperature
40 A Total (20 A Per Diode Leg)
This is a Pb−Free Device
SCHOTTKY BARRIER
RECTIFIER
40 AMPERES
100 VOLTS
1
Applications
2, 4
• Power Supply − Output Rectification
• Power Management
• Instrumentation
3
MARKING
DIAGRAM
Mechanical Characteristics:
•
•
•
•
•
Case: Epoxy, Molded
Epoxy Meets UL 94 V−0 @ 0.125 in
Weight: 4.3 Grams (Approximately)
Finish: All External Surfaces Corrosion Resistant and Terminal
Leads are Readily Solderable
Lead Temperature for Soldering Purposes:
260°C Max. for 10 Seconds
MAXIMUM RATINGS
B40H100
AYWWG
TO−247AC
CASE 340L
STYLE 2
A
Y
WW
B40H100
G
Please See the Table on the Following Page
= Assembly Location
= Year
= Work Week
= Device Code
= Pb−Free Package
ORDERING INFORMATION
© Semiconductor Components Industries, LLC, 2006
August, 2006 − Rev. 1
1
Device
Package
Shipping
MBR40H100WTG
TO−247
(Pb−Free)
30 Units/Rail
Publication Order Number:
MBR40H100WT/D
MBR40H100WT
MAXIMUM RATINGS (Per Diode Leg)
Rating
Symbol
Value
Unit
Peak Repetitive Reverse Voltage
Working Peak Reverse Voltage
DC Blocking Voltage
VRRM
VRWM
VR
100
V
Average Rectified Forward Current
TC = 148°C, per Diode
TC = 150°C, per Device
IF(AV)
Peak Repetitive Forward Current
(Square Wave, 20 kHz) TC = 144°C
IFRM
40
A
Nonrepetitive Peak Surge Current
(Surge applied at rated load conditions halfwave, single phase, 60 Hz)
IFSM
200
A
Operating Junction Temperature (Note 1)
TJ
+175
°C
Storage Temperature
Tstg
*65 to +175
°C
Voltage Rate of Change (Rated VR)
dv/dt
10,000
V/ms
WAVAL
400
mJ
> 400
> 8000
V
2.0
60
°C/W
Controlled Avalanche Energy (see test conditions in Figures 10 and 11)
A
20
40
ESD Ratings: Machine Model = C
Human Body Model = 3B
THERMAL CHARACTERISTICS
Maximum Thermal Resistance − Junction−to−Case (min. pad)
− Junction−to−Ambient (min. pad)
RqJC
RqJA
ELECTRICAL CHARACTERISTICS
Characterisitc
Symbol
Instantaneous Forward Voltage (Note 2)
(IF = 20 A, TJ = 25°C)
(IF = 20 A, TJ = 125°C)
(IF = 40 A, TJ = 25°C)
(IF = 40 A, TJ = 125°C)
vF
Instantaneous Reverse Current (Note 2)
(Rated dc Voltage, TJ = 125°C)
(Rated dc Voltage, TJ = 25°C)
iR
Min
Typ
Max
−
−
−
−
0.74
0.61
0.85
0.72
0.80
0.67
0.90
0.76
−
−
2.0
0.0012
10
0.01
Unit
V
mA
Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit
values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied,
damage may occur and reliability may be affected.
1. The heat generated must be less than the thermal conductivity from Junction−to−Ambient: dPD/dTJ < 1/RqJA.
2. Pulse Test: Pulse Width = 300 ms, Duty Cycle ≤ 2.0%.
http://onsemi.com
2
100
IF, INSTANTANEOUS FORWARD CURRENT (A)
IF, INSTANTANEOUS FORWARD CURRENT (A)
MBR40H100WT
175°C
150°C
10
25°C
125°C
1.0
0.1
0
0.1 0.2 0.3 0.4 0.5 0.6
0.7 0.8 0.9 1.0 1.1
VF, INSTANTANEOUS FORWARD VOLTAGE (V)
100
175°C
150°C
10
125°C
1.0
0.1
0
Figure 2. Maximum Forward Voltage
1.0E−01
IR, MAXIMUM REVERSE CURRENT (A)
1.0E−01
IR, REVERSE CURRENT (A)
TJ = 125°C
1.0E−04
1.0E−05
1.0E−05
TJ = 25°C
1.0E−06
1.0E−07
1.0E−08
0
20
40
60
80
100
1.0E−08
0
20
40
60
80
VR, REVERSE VOLTAGE (VOLTS)
VR, REVERSE VOLTAGE (VOLTS)
Figure 3. Typical Reverse Current
Figure 4. Maximum Reverse Current
32
IF(AV), AVERAGE FORWARD CURRENT (A)
IF, AVERAGE FORWARD CURRENT (A)
TJ = 25°C
1.0E−06
1.0E−07
dc
28
Square Wave
20
16
12
8.0
4.0
120
TJ = 125°C
1.0E−03
1.0E−04
0
TJ = 150°C
1.0E−02
TJ = 150°C
1.0E−03
24
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2
VF, INSTANTANEOUS FORWARD VOLTAGE (V)
Figure 1. Typical Forward Voltage
1.0E−02
25°C
130
140
150
160
170
180
100
20
RqJA = 16°C/W
18
16
dc
14
12
Square Wave
10
8.0
6.0
4.0
2.0
0
dc
RqJA = 60°C/W
No Heatsink
0
25
50
Square Wave
75
100
125
150
175
TC, CASE TEMPERATURE (°C)
TA, AMBIENT TEMPERATURE (°C)
Figure 5. Current Derating, Case, Per Leg
Figure 6. Current Derating, Ambient, Per Leg
http://onsemi.com
3
R(t), TRANSIENT THERMAL RESISTANCE
10000
30
28
TJ = 25°C
TJ = 175°C
24
C, CAPACITANCE (pF)
PF(AV), AVERAGE POWER DISSIPATION (W)
MBR40H100WT
Square Wave
20
dc
16
12
8.0
1000
100
4.0
0
10
4.0
0
8.0
12
16
20
28 30
24
0
20
40
60
80
IF(AV), AVERAGE FORWARD CURRENT (A)
VR, REVERSE VOLTAGE (V)
Figure 7. Forward Power Dissipation
Figure 8. Capacitance
100
10
1
0.1
D = 0.5
0.2
0.1
0.05
0.01
P(pk)
t1
0.01
SINGLE PULSE
0.001
0.000001
0.00001
t2
DUTY CYCLE, D = t1/t2
0.0001
0.001
0.01
0.1
1
t1, TIME (sec)
Figure 9. Thermal Response Junction−to−Case
http://onsemi.com
4
10
100
1000
MBR40H100WT
+VDD
IL
10 mH COIL
BVDUT
VD
MERCURY
SWITCH
S1
ID
ID
IL
DUT
VDD
t0
Figure 10. Test Circuit
t1
t2
t
Figure 11. Current−Voltage Waveforms
elements are small Equation (1) approximates the total
energy transferred to the diode. It can be seen from this
equation that if the VDD voltage is low compared to the
breakdown voltage of the device, the amount of energy
contributed by the supply during breakdown is small and the
total energy can be assumed to be nearly equal to the energy
stored in the coil during the time when S1 was closed,
Equation (2).
The unclamped inductive switching circuit shown in
Figure 10 was used to demonstrate the controlled avalanche
capability of this device. A mercury switch was used instead
of an electronic switch to simulate a noisy environment
when the switch was being opened.
When S1 is closed at t0 the current in the inductor IL ramps
up linearly; and energy is stored in the coil. At t1 the switch
is opened and the voltage across the diode under test begins
to rise rapidly, due to di/dt effects, when this induced voltage
reaches the breakdown voltage of the diode, it is clamped at
BVDUT and the diode begins to conduct the full load current
which now starts to decay linearly through the diode, and
goes to zero at t2.
By solving the loop equation at the point in time when S1
is opened; and calculating the energy that is transferred to
the diode it can be shown that the total energy transferred is
equal to the energy stored in the inductor plus a finite amount
of energy from the VDD power supply while the diode is in
breakdown (from t1 to t2) minus any losses due to finite
component resistances. Assuming the component resistive
EQUATION (1):
ǒ
BV
2
DUT
W
[ 1 LI LPK
AVAL
2
BV
–V
DUT DD
EQUATION (2):
2
W
[ 1 LI LPK
AVAL
2
http://onsemi.com
5
Ǔ
MBR40H100WT
PACKAGE DIMENSIONS
TO−247 PSI
CASE 340L−02
ISSUE D
−T−
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
C
−B−
E
U
N
L
4
A
−Q−
1
2
0.63 (0.025)
3
M
T B
M
P
−Y−
K
F 2 PL
W
J
D 3 PL
0.25 (0.010)
M
Y Q
MILLIMETERS
MIN
MAX
20.32
21.08
15.75
16.26
4.70
5.30
1.00
1.40
2.20
2.60
1.65
2.13
5.45 BSC
1.50
2.49
0.40
0.80
20.06
20.83
5.40
6.20
4.32
5.49
−−−
4.50
3.55
3.65
6.15 BSC
2.87
3.12
STYLE 2:
PIN 1.
2.
3.
4.
H
G
DIM
A
B
C
D
E
F
G
H
J
K
L
N
P
Q
U
W
S
INCHES
MIN
MAX
0.800
8.30
0.620
0.640
0.185
0.209
0.040
0.055
0.087
0.102
0.065
0.084
0.215 BSC
0.059
0.098
0.016
0.031
0.790
0.820
0.212
0.244
0.170
0.216
−−− 0.177
0.140
0.144
0.242 BSC
0.113
0.123
ANODE
CATHODE (S)
ANODE 2
CATHODES (S)
SWITCHMODE is a trademark of Semiconductor Components Industries, LLC.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
6
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MBR40H100WT/D