TPA6140A2 www.ti.com .................................................................................................................................................................................................. SLOS598 – MARCH 2009 CLASS-G DIRECTPATH™ STEREO HEADPHONE AMPLIFIER WITH I2C VOLUME CONTROL FEATURES 1 • TI Class-G Technology Significantly Prolongs Battery Life and Music Playback Time – 0.6 mA / Ch Quiescent Current – 50% to 80% Lower Quiescent Current than Ground-Referenced Class-AB Headphone Amplifiers • DirectPathTM Technology Eliminates Large Output DC-Blocking Capacitors – Outputs Biased at 0 V – Improves Low Frequency Audio Fidelity • I2C Volume Control – –59 dB to +4 dB Gain • Active Click and Pop Suppression • Fully Differential Inputs Reduce System Noise – Also Configurable as Single-Ended Inputs • SGND Pin Eliminates Ground Loop Noise • Wide Power Supply Range: 2.5 V to 5.5 V • 100 dB Power Supply Noise Rejection • Short-Circuit Current Limiter • Thermal-Overload Protection • Software Compatible with TPA6130A2 • 0,4 mm Pitch, 1,6 mm × 1,6 mm WCSP Package 2 DESCRIPTION The TPA6140A2 (also known as TPA6140) is a Class-G DirectPath™ stereo headphone amplifier with built-in I2C volume control. Class-G technology maximizes battery life by adjusting the voltage supplies of the headphone amplifier based on the audio signal level. At low level audio signals, the internal supply voltage is reduced to minimize power dissipation. DirectPathTM technology eliminates external DC-blocking capacitors. The device operates from a 2.5 V to 5.5 V supply voltage. Class-G operation keeps total supply current below 5.0 mA while delivering 500 µW per channel into 32 Ω. Shutdown mode reduces the supply current to less than 3 µA and is activated through the I2C interface. The TPA6140A2 (TPA6140) I2C register map is compatible to the TPA6130A2, simplifying software development. The amplifier outputs have short-circuit and thermal-overload protection along with ±8 kV HBM ESD protection, simplifying end equipment compliance to the IEC 61000-4-2 ESD standard. The TPA6140A2 (TPA6140) is available in a 0,4 mm pitch, 16-bump 1,6 mm × 1,6 mm WCSP (YFF) package. 1 mF APPLICATIONS • • • Cellular Phones / Music Phones Portable Media / MP3 Players Portable CD / DVD Players OUTR+ INR+ OUTR- INR- OUTL+ INL+ OUTL- INL- CODEC OUTR TPA6140A2 OUTL SGND SCL SDA SCL AGND SDA Vbat AVDD 2.2 mH 2.2 mF SW HPVDD HPVSS CPP CPN 2.2 mF 1 mF 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Class-G DirectPath, DirectPath are trademarks of Texas Instruments. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2009, Texas Instruments Incorporated TPA6140A2 SLOS598 – MARCH 2009 .................................................................................................................................................................................................. www.ti.com These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. FUNCTIONAL BLOCK DIAGRAM AVDD Ramp Generator + SW Gate Drivers – Comparator 2.2 mH AGND Compensation Network + HPVDD – Audio Level Detector AVDD Optimizer Thermal Protection HPVDD INL- 2.2 mF – OUTL + INL+ HPVSS Short-Circuit Protection HPVDD – INR- OUTR + INR+ HPVSS HPVDD HPVDD CPP SDA I2C Interface SCL Click-and-Pop Suppression Charge Pump 1 mF CPN SGND 2 HPVSS 2.2 mF Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): TPA6140A2 TPA6140A2 www.ti.com .................................................................................................................................................................................................. SLOS598 – MARCH 2009 DEVICE PINOUT WCSP PACKAGE (TOP VIEW) A1 A2 A3 A4 SW AVDD OUTL INL- B1 B2 B3 B4 AGND CPP HPVDD INL+ C1 C2 C3 C4 CPN HPVSS SGND INR+ D1 D2 D3 D4 SDA SCL OUTR INR- TERMINAL FUNCTIONS TERMINAL NAME BALL WCSP INPUT / OUTPUT / POWER (I/O/P) DESCRIPTION INL– A4 I Inverting left input for differential signals; connect to left input signal through 1 µF capacitor for single-ended input applications INL+ B4 I Non-inverting left input for differential signals; connect to ground through 1 µF capacitor for single-ended input applications INR– C4 I Inverting right input for differential signals; connect to right input signal through 1 µF capacitor for single-ended input applications INR+ D4 I Non-inverting right input for differential signals; connect to ground through 1 µF capacitor for single-ended input applications SGND C3 I Sense Ground; connect to shield terminal of headphone jack or to AGND SDA D1 I/O I2C Data; 1.8 V logic compliant SCL D2 I I2C Clock; 1.8 V logic compliant OUTL A3 O Left headphone amplifier output; connect to left terminal of headphone jack OUTR D3 O Right headphone amplifier output; connect to right terminal of headphone jack CPP B2 P Charge pump positive flying cap; connect to positive side of capacitor between CPP and CPN CPN C1 P Charge pump negative flying cap; connect to negative side of capacitor between CPP and CPN SW A1 P Buck converter switching node AVDD A2 P Primary power supply for device HPVDD B3 P Power supply for headphone amplifier (DC/DC output node) AGND B1 P Main Ground for headphone amplifiers, DC/DC converter, and charge pump HPVSS C2 P Charge pump output; connect 2.2 µF capacitor to GND ORDERING INFORMATION PACKAGED DEVICES (1) PART NUMBER (2) SYMBOL 16-ball, 1,6 mm × 1,6 mm WCSP TPA6140A2YFFR AIFI 16-ball, 1,6 mm × 1,6 mm WCSP TPA6140A2YFFT AIFI TA –40°C to 85°C (1) (2) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI Web site at www.ti.com. YFF packages are only available taped and reeled. The suffix “R” indicates a reel of 3000, the suffix “T” indicates a reel of 250. 3 Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): TPA6140A2 TPA6140A2 SLOS598 – MARCH 2009 .................................................................................................................................................................................................. www.ti.com ABSOLUTE MAXIMUM RATINGS (1) over operating free-air temperature range, TA = 25°C (unless otherwise noted) VALUE / UNIT VI Supply voltage, AVDD –0.3 V to 6.0 V Amplifier supply voltage, HPVDD –0.3 V to 2.0 V Input voltage –0.3 V to HPVDD +0.3 V I2C voltage –0.3 V to AVDD Output continuous total power dissipation See Dissipation Rating Table TA Operating free-air temperature range –40°C to 85°C TJ Operating junction temperature range –40°C to 150°C Tstg Storage temperature range –65°C to 85°C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds ESD Protection – HBM (1) 260°C OUTL, OUTR, SGND 8 kV All other pins 2 kV Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute–maximum–rated conditions for extended periods may affect device reliability. DISSIPATION RATINGS TABLE (1) (2) (1) (2) PACKAGE TA < 25°C POWER RATING OPERATING FACTOR ABOVE TA = 25°C TA = 70°C POWER RATING TA = 85°C POWER RATING YFF (WCSP) 1.25 W 10 mW/°C 800 mW 650 mW Derating factor measured with JEDEC High K board: 1S0P – One signal layer and zero plane layers. See JEDEC Standard 51-3 for Low-K board, JEDEC Standard 51-7 for High-K board, and JEDEC Standard 51-12 for using package thermal information. See JEDEC document page for downloadable copies: http://www.jedec.org/download/default.cfm. RECOMMENDED OPERATING CONDITIONS Supply voltage, AVDD VIH High-level input voltage SDA, SCL VIL Low-level input voltage SDA, SCL TA MIN MAX 2.5 5.5 1.3 UNIT V V 0.35 V V Voltage applied to Output; OUTR, OUTL (when SWS = 1, device disabled) –0.3 3.6 Voltage applied to Output; OUTR, OUTL (when SWS = 0, HiZ_L = HiZ_R = 1, device in HI-Z mode) –1.8 1.8 V Operating free-air temperature –40 85 °C 4 Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): TPA6140A2 TPA6140A2 www.ti.com .................................................................................................................................................................................................. SLOS598 – MARCH 2009 ELECTRICAL CHARACTERISTICS TA = 25°C (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX 90 UNIT PSRR Power supply rejection ratio AVDD = 2.5 V to 5.5 V, inputs grounded, GAIN = 0 dB CMRR Common-mode rejection ratio HPVDD = 1.3 V to 1.8 V, GAIN = 0 dB |IIH| High-level input current AVDD = 2.5 V to 5.5 V, VI = AVDD SCL, SDA 1 µA |IIL| Low-level input current AVDD = 2.5 V to 5.5 V, VI = 0 V SCL, SDA 1 µA ISD Soft shutdown current SW Shutdown mode, VDD = 2.5 V to 5.5 V, SWS bit = 1 1 3 µA AVDD = 3.6 V HPVDD = 1.3 V, Amplifiers active, no load, no input signal 1.2 2.0 AVDD = 3.6 V, POUT = 100 µW into 32 Ω , fAUD = 1 kHz 2.5 AVDD = 3.6 V, POUT = 500 µW into 32 Ω (1), fAUD = 1 kHz 4.0 (1) IDD Total supply current (1) (1) 105 dB 68 dB AVDD = 3.6 V, POUT = 1 mW into 32 Ω , fAUD = 1 kHz 6.8 AVDD = 3.6 V, HiZ_L = HiZ_R = HIGH (High output impedance mode) 1.0 mA 2.0 Per channel output power assuming a 10 dB crest factor TIMING CHARACTERISTICS For I2C interface signals over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN No wait states TYP MAX UNIT 400 kHz fSCL Frequency, SCL tW(H) Pulse duration, SCL high 0.6 µs tW(L) Pulse duration, SCL low 1.3 µs tSU1 Setup time, SDA to SCL 100 µs tH1 Hold time, SCL to SDA 10 ns t(BUF) Bus free time between stop and start condition 1.3 µs tSU2 Setup time, SCL to start condition 0.6 µs tH2 Hold time, start condition to SCL 0.6 µs tSU3 Setup time, SCL to stop condition 0.6 µs tw(L) tw(H) SCL t su1 th1 SDA Figure 1. SCL and SDA Timing 5 Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): TPA6140A2 TPA6140A2 SLOS598 – MARCH 2009 .................................................................................................................................................................................................. www.ti.com SCL th2 t(buf) tsu2 tsu3 Start Condition Stop Condition SDA Figure 2. Start and Stop Conditions Timing OPERATING CHARACTERISTICS AVDD = 3.6 V , TA = 25°C, GAIN = 0 dB, RL = 32 Ω (unless otherwise noted) PARAMETER Output power (1) (Outputs in Phase) PO THD+N Total harmonic distortion plus noise (2) TEST CONDITIONS MIN TYP AVDD = 2.7V, THD = 1%, f = 1 kHz 26 AVDD = 2.7V, THD = 10%, f = 1 kHz 32 AVDD = 2.7V, THD = 1%, f = 1 kHz, RL = 16Ω 25 PO = 10 mW into 16 Ω, f = 1 kHz UNIT mW 0.02% PO = 20 mW into 32 Ω, f = 1 kHz 200 mVpp ripple, f = 217 Hz MAX 0.01% 80 100 kSVR AC-Power supply rejection ratio ΔAV Gain matching Between left and right channels VOS Output offset voltage AVDD = 2.5 V to 5.5 V, inputs grounded En Noise output voltage A-weighted 5.3 µVRMS fBUCK Buck converter switching frequency PO = 0.5 mW into 32 Ω, f = 1 kHz 600 kHz fPUMP Charge pump switching frequency 200 mVpp ripple, f = 4 kHz dB 90 1% –0.5 0 PO = 0.5 mW into 32 Ω, f = 1 kHz 315 PO = 15 mW into 32 Ω, f = 1 kHz 1260 Start-up time from shutdown 0.5 mV kHz 5 ms RIN,SE Single Ended Input impedance Gain = 4 dB, per input node 15.6 kΩ RIN,DF Differential input impedance Gain = 4 dB, per input node 31.2 kΩ SNR Signal-to-noise ratio VOUT = 1 VRMS, GAIN = 4 dB, no load 105 dB Threshold 165 Hysteresis 35 Thermal shutdown ZO,SD ZO,HI-Z Output impedance in shutdown Output impedance in Hi-Z mode Crosstalk VCM (1) (2) SWS = 1, DC value °C 8 kΩ 40 kHz, 1.8 VPEAK signal max 8.5 kΩ 6 MHz, 1.8 VPEAK signal max 600 Ω 13 MHz, 1.8 VPEAK signal max 400 Ω PO = 15 mW, f = 1 kHz –80 dB Input common-mode voltage range 0 1.4 V Per channel output power A-weighted 6 Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): TPA6140A2 TPA6140A2 www.ti.com .................................................................................................................................................................................................. SLOS598 – MARCH 2009 TYPICAL CHARACTERISTICS TA = 25°C, AVDD (VDD) = 3.6 V, GAIN = 0 dB, CHPVDD = CHPVSS = 2.2 µF, CINPUT = CFLYING = 1 µF, Outputs out of phase TOTAL HARMONIC DISTORTION + NOISE vs OUTPUT POWER 9 8 7 6 5 4 3 2 1 3.0 3.5 4.0 4.5 5.0 5.5 THD+N − Total Harmonic Distortion + Noise − % VDD − Supply Voltage − V 10 In Phase 1 Out of Phase 0.1 0.01 0.0001 0.001 0.01 0.1 PO − Output Power − W G002 Figure 4. TOTAL HARMONIC DISTORTION + NOISE vs OUTPUT POWER TOTAL HARMONIC DISTORTION + NOISE vs OUTPUT POWER f = 1 kHz RL = 16 Ω VDD = 2.5 V 10 VDD = 3.6 V 1 VDD = 5 V 0.1 0.01 0.0001 0.001 0.01 0.1 PO − Output Power − W THD+N − Total Harmonic Distortion + Noise − % f = 1 kHz RL = 16 Ω VDD = 3.6 V G001 100 100 f = 1 kHz RL = 32 Ω VDD = 2.5 V 10 VDD = 3.6 V 1 VDD = 5 V 0.1 0.01 0.0001 0.001 0.01 0.1 PO − Output Power − W G003 G004 Figure 5. Figure 6. TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY 1 RL = 16 Ω VDD = 2.5 V PO = 1 mW per Channel 0.1 0.01 PO = 10 mW per Channel PO = 4 mW per Channel 0.001 20 100 Figure 3. THD+N − Total Harmonic Distortion + Noise − % 0 2.5 100 1k f − Frequency − Hz 10k 20k THD+N − Total Harmonic Distortion + Noise − % Quiescent Supply Current − mA 10 THD+N − Total Harmonic Distortion + Noise − % QUIESCENT SUPPLY CURRENT vs SUPPLY VOLTAGE 1 RL = 32 Ω VDD = 2.5 V PO = 1 mW per Channel 0.1 PO = 10 mW per Channel 0.01 PO = 4 mW per Channel 0.001 20 G005 Figure 7. 100 1k f − Frequency − Hz 10k 20k G006 Figure 8. 7 Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): TPA6140A2 TPA6140A2 SLOS598 – MARCH 2009 .................................................................................................................................................................................................. www.ti.com TYPICAL CHARACTERISTICS (continued) TA = 25°C, AVDD (VDD) = 3.6 V, GAIN = 0 dB, CHPVDD = CHPVSS = 2.2 µF, CINPUT = CFLYING = 1 µF, Outputs out of phase RL = 16 Ω VDD = 3.6 V PO = 1 mW per Channel PO = 10 mW per Channel 0.1 0.01 PO = 15 mW per Channel 0.001 20 100 1k 10k THD+N − Total Harmonic Distortion + Noise − % 20k RL = 32 Ω VDD = 3.6 V 0.1 PO = 1 mW per Channel PO = 10 mW per Channel 0.01 PO = 20 mW per Channel 0.001 20 100 1k 10k f − Frequency − Hz G007 TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY PO = 1 mW per Channel PO = 10 mW per Channel 0.1 0.01 PO = 15 mW per Channel 0.001 20 100 1k 10k f − Frequency − Hz 20k 1 RL = 32 Ω VDD = 5 V 0.1 PO = 1 mW per Channel PO = 10 mW per Channel 0.01 PO = 20 mW per Channel 0.001 20 100 1k 10k f − Frequency − Hz G009 Figure 12. OUTPUT POWER PER CHANNEL vs SUPPLY VOLTAGE OUTPUT POWER PER CHANNEL vs SUPPLY VOLTAGE PO − Output Power per Channel − mW RL = 16 Ω In Phase THD+N = 10% 40 30 THD+N = 1% 20 10 3.0 3.5 4.0 4.5 VDD − Supply Voltage − V 5.0 5.5 20k G010 Figure 11. 60 20k G008 Figure 10. RL = 16 Ω VDD = 5 V 0 2.5 1 Figure 9. 1 50 THD+N − Total Harmonic Distortion + Noise − % 1 f − Frequency − Hz PO − Output Power per Channel − mW TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY THD+N − Total Harmonic Distortion + Noise − % THD+N − Total Harmonic Distortion + Noise − % TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY 60 50 RL = 32 Ω In Phase THD+N = 10% 40 30 THD+N = 1% 20 10 0 2.5 G011 Figure 13. 3.0 3.5 4.0 4.5 VDD − Supply Voltage − V 5.0 5.5 G012 Figure 14. 8 Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): TPA6140A2 TPA6140A2 www.ti.com .................................................................................................................................................................................................. SLOS598 – MARCH 2009 TYPICAL CHARACTERISTICS (continued) TA = 25°C, AVDD (VDD) = 3.6 V, GAIN = 0 dB, CHPVDD = CHPVSS = 2.2 µF, CINPUT = CFLYING = 1 µF, Outputs out of phase OUTPUT POWER vs LOAD RESISTANCE OUTPUT POWER vs LOAD RESISTANCE 50 50 40 VDD = 3.6 V 35 30 25 20 15 VDD = 2.5 V 10 25 20 15 RL − Load Resistance − Ω SUPPLY RIPPLE REJECTION RATIO vs FREQUENCY RL = 16 Ω Supply Ripple = 0.2 Vpp Sine Wave VDD = 5 V VDD = 3.6 V VDD = 2.5 V 100 1k 10k f − Frequency − Hz 20k 0 −20 RL = 32 Ω Supply Ripple = 0.2 Vpp Sine Wave −40 −60 VDD = 5 V VDD = 3.6 V −80 VDD = 2.5 V −100 −120 20 100 1k 10k f − Frequency − Hz G015 Figure 17. Figure 18. SUPPLY CURRENT vs TOTAL OUTPUT POWER SUPPLY CURRENT vs TOTAL OUTPUT POWER 100 20k G016 100 IDD − Supply Current − mA f = 1 kHz RL = 16 Ω VDD = 3.6 V VDD = 2.5 V f = 1 kHz RL = 32 Ω VDD = 3.6 V 10 VDD = 2.5 V VDD = 5 V VDD = 5 V 1 0.001 G014 SUPPLY RIPPLE REJECTION RATIO vs FREQUENCY −100 10 1k Figure 16. −60 −120 20 100 G013 −40 −80 VDD = 2.5 V Figure 15. 0 −20 VDD = 3.6 V 10 0 10 kSVR − Supply Ripple Rejection Ratio− dB kSVR − Supply Ripple Rejection Ratio − dB 30 5 RL − Load Resistance − Ω IDD − Supply Current − mA 35 0 10 1k VDD = 5 V 40 5 100 THD+N = 1% In Phase 45 PO − Output Power − mW PO − Output Power − mW THD+N = 1% Out of Phase VDD = 5 V 45 0.01 0.1 1 PO − Total Output Power − mW 10 100 1 0.001 G017 Figure 19. 0.01 0.1 1 PO − Total Output Power − mW 10 100 G018 Figure 20. 9 Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): TPA6140A2 TPA6140A2 SLOS598 – MARCH 2009 .................................................................................................................................................................................................. www.ti.com TYPICAL CHARACTERISTICS (continued) TA = 25°C, AVDD (VDD) = 3.6 V, GAIN = 0 dB, CHPVDD = CHPVSS = 2.2 µF, CINPUT = CFLYING = 1 µF, Outputs out of phase TOTAL POWER DISSIPATION vs TOTAL OUTPUT POWER OUTPUT VOLTAGE vs SUPPLY VOLTAGE 2.0 100 RL = 16 Ω 10 RL = 32 Ω 0.1 1 10 1.4 1.2 1.0 0.8 0.6 RL = 32 Ω 0.4 0.0 2.5 100 PO − Total Output Power − mW RL = 16 Ω G019 4.0 4.5 5.0 5.5 G020 Figure 22. CROSSTALK vs FREQUENCY OUTPUT AMPLITUDE vs FREQUENCY 0 VO − Output Amplitude − dBV −40 −60 −80 −100 20 3.5 Figure 21. RL = 16 Ω PO = 15 mW −20 3.0 VDD − Supply Voltage − V 0 Crosstalk − dB RL = 1 kΩ RL = 600 Ω 1.6 0.2 1 0.01 Single Channel RL = 16 Ω −30 −60 −90 −120 −150 100 1k 10k f − Frequency − Hz 20k 0 5000 10000 15000 20000 f − Frequency − Hz G021 G022 Figure 23. Figure 24. STARTUP WAVEFORM vs TIME SHUTDOWN WAVEFORM vs TIME 5 5 RL = 16 Ω VIN = 0.5 Vrms @ 1 kHz 3 SDA 2 1 RL = 16 Ω VIN = 0.5 Vrms @ 20 kHz 4 V − Voltage − V 4 V − Voltage − V f = 1 kHz THD+N = 1% 1.8 VO − Output Voltage − Vrms PT − Total Power Dissipation − W 1k VOUT 0 Disable 3 SDA 2 VOUT 1 0 Enable −1 −1 0 1 2 3 4 5 6 t − Time − ms 7 8 9 10 0 G023 Figure 25. 50 100 t − Time − µs 150 200 G024 Figure 26. 10 Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): TPA6140A2 TPA6140A2 www.ti.com .................................................................................................................................................................................................. SLOS598 – MARCH 2009 APPLICATION INFORMATION APPLICATION CIRCUIT 1 mF OUTR+ INR+ OUTR- INR- OUTL+ INL+ OUTL- INL- CODEC OUTR TPA6140A2 OUTL SGND SCL SDA SCL Vbat AVDD 2.2 mH SW HPVDD AGND SDA HPVSS CPP 2.2 mF CPN 2.2 mF 1 mF Figure 27. Typical Apps Configuration with Differential Input Signals 1 mF OUTR INR+ INR- CODEC OUTR TPA6140A2 OUTL INL+ OUTL INLSGND SCL SDA SCL Vbat AVDD 2.2 mH 2.2 mF AGND SDA SW HPVDD HPVSS CPP CPN 2.2 mF 1 mF Figure 28. Typical Apps Configuration with Single-Ended Input Signals 11 Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): TPA6140A2 TPA6140A2 SLOS598 – MARCH 2009 .................................................................................................................................................................................................. www.ti.com CLASS-G HEADPHONE AMPLIFIER Class-G amplifiers use adaptive supply rails. The TPA6140A2 includes a built-in step-down converter to create the headphone amplifier positive supply voltage, HPVDD. A charge pump inverts HPVDD and creates the amplifier negative supply voltage, HPVSS. This allows the headphone amplifier output to be centered at 0 V and eliminates DC blocking capacitors. When audio signal amplitude is low, the step-down converter generates a low HPVDD voltage. This minimizes TPA6140A2 power consumption while playing low amplitude, high fidelity audio. If audio amplitude increases, either due to louder music or a transient peak, then the step-down converter generates a higher HPVDD voltage. The HPVDD rise rate is faster than the audio peak rise time. This prevents audio distortion or clipping. Audio quality and noise floor are not affected by HPVDD. This adaptive HPVDD minimizes TPA6140A2 supply current while avoiding clipping and distortion. Because normal listening levels are below 200 mVRMS, HPVDD is most often at its lowest voltage. Thus, the TPA6140A2 has higher efficiency than traditional Class-AB headphone amplifiers. The following equations compare a Class-AB amplifier to a Class-G amplifier. Both operate with identical battery voltage, load impedance, and output voltage swing. For this study case, we assume a normal listening level of 200 mVRMS with no DirectPath™ in order to simplify the calculations. • PSUP: Supplied power • VSUP: Supply voltage • ISUP: Supply current • VREG: DC/DC converter output voltage • PREG: DC/DC converter output power • VLOAD: Voltage across the load • RLOAD: Load impedance • PLOAD: Power dissipated at the load • ILOAD: Current supplied to the load Given an amplifier driving 200 mVRMS into a 32 Ω load, the output current to the load is: V 200 mVRMS ILOAD = LOAD = = 6.25 mA RLOAD 32 W (1) Assuming a quiescent current of 1 mA (IDDQ) the total current supplied to the amplifier is: ISUP = ILOAD + IDDQ = 7.25 mA (2) The total power supplied to a Class-AB amplifier is then calculated as: PSUP = VSUP ´ ISUP = 4.2 V ´ 7.25 mA = 30.45 mW (3) For a Class-G amplifier where the voltage rails are generated by a switching DC/DC converter, the supplied power will depend on the DC/DC converter output voltage and efficiency. Assuming the DC/DC converter output voltage is 1.3 V: PREG = VREG ´ ISUP = 1.3 V ´ 7.25 mA = 9.425 mW (4) The total supplied power will be the DC/DC converter output power divided by the efficiency of the DC/DC converter. Assuming 90% step-down efficiency, total power supplied to the Class-G amplifier is: P PSUP = REG = 11.09 mW 90% (5) Class-G headphone amplifiers achieve much higher efficiency than equivalent Class-AB amplifiers. 12 Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): TPA6140A2 TPA6140A2 www.ti.com .................................................................................................................................................................................................. SLOS598 – MARCH 2009 INDUCTOR SELECTION The TPA6140A2 requires one inductor for its DC/DC converter. The following table lists recommended inductors. Inductors not shown on this table can be be used if they have similar performance characteristics. When selecting an inductor observe the following rules: • Lower DCR increases DC/DC converter efficiency. • The minimum working inductance should never be below 1 µH. • Include temperature and aging derating factors into the inductor value calculations. MANUFACTURER PART NUMBER TOKO MDT2012-CH2R2A LQM21PN2R2MC0D Murata LQH2MCN2R2M02L BRL2012T2R2M Taiyo Yuden BRC1608T2R2M GROUND SENSE FUNCTION The ground sense pin, SGND, reduces ground-loop noise when the audio output jack is connected to a different ground reference than codec and amplifier ground. Always connect the SGND pin to the headphone jack. This reduces output offset voltage and eliminates turn-on pop. Figure 29 shows how to connect SGND when an FM radio antenna function is implemented on the headphone wire. The nH coil and capacitor separate the RF signal from the audio GND signal. In this case, SGND is used to eliminate the offset voltage that is generated from the audio signal current and the RF coil low-frequency impedance. The voltage difference between SGND and AGND cannot be greater than ±300 mV. The amplifier performance degrades if the voltage difference between SGND and AGND is greater than ±300 mV. CODEC TPA6140A2 OUTR+ INR+ OUTR- INR- OUTL+ INL+ OUTL- INL- OUTR OUTL SGND SCL SDA Vbat 2.2 mH 2.2 mF SCL SDA AVDD SW HPVDD AGND HPVSS CPP CPN FM Tuner 2.2 mF nH coil 1mF Figure 29. Sense Ground 13 Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): TPA6140A2 TPA6140A2 SLOS598 – MARCH 2009 .................................................................................................................................................................................................. www.ti.com HIGH OUTPUT IMPEDANCE The TPA6140A2 has a HI-Z bit option that increases output impedance while muting the amplifier. Set the HiZ_L and HiZ_R bits (register 3, bits 1 and 0) to HIGH to activate the HI-Z mode. This feature allows the headphone output jack to be shared for other functions besides audio. For example, sharing of a headphone jack between audio and video as shown in Figure 30. In HI-Z mode, the TPA6140A2 output impedance is high enough to prevent video signal attenuation. OUTPUT IMPEDANCE SWS BIT HI-Z BIT 1 0 8 kΩ 1 1 8.5 kΩ 0 0 ≤1Ω SUPPLY CURRENT MAXIMUM EXTERNAL VOLTAGE ALLOWED ON OUTPUT PINS COMMENTS < 3 µA –0.3 V to 3.3 V (1) Shutdown mode 1.2 mA – Active mode 1 mA –1.8 V to 1.8 V HI-Z mode 8.5 kΩ @ 40kHz 0 600 Ω @ 6 MHz 1 400 Ω @ 13 MHz (1) If AVDD is < 3.3 V, then maximum allowed external voltage applied is AVDD in this mode Video Buffer/Amp (i.e., THS7375) + 75 W – TPA6140A2 OUTR OUTL Figure 30. Sharing One Connector Between Audio and Video Signals Example HEADPHONE AMPLIFIERS Single-supply headphone amplifiers typically require dc-blocking capacitors to remove dc bias from their output voltage. The top drawing in Figure 31 illustrates this connection. If dc bias is not removed, large dc current will flow through the headphones which wastes power, clips the output signal, and potentially damages the headphones. These dc-blocking capacitors are often large in value and size. Headphone speakers have a typical resistance between 16 Ω and 32 Ω. This combination creates a high-pass filter with a cutoff frequency as shown in Equation 6, where RL is the load impedance, CO is the dc-blocking capacitor, and fC is the cutoff frequency. 1 fC = 2pRLCO (6) For a given high-pass cutoff frequency and load impedance, the required dc-blocking capacitor is found as: 1 CO = 2pfCRL (7) Reducing fC improves low frequency fidelity and requires a larger dc-blocking capacitor. To achieve a 20 Hz cutoff with 16 Ω headphones, CO must be at least 500 µF. Large capacitor values require large packages, consuming PCB area, increasing height, and increasing cost of assembly. During start-up or shutdown the dc-blocking capacitor has to be charged or discharged. This causes an audible pop on start-up and power-down. Large dc-blocking capacitors also reduce audio output signal fidelity. 14 Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): TPA6140A2 TPA6140A2 www.ti.com .................................................................................................................................................................................................. SLOS598 – MARCH 2009 Two different headphone amplifier architectures are available to eliminate the need for dc-blocking capacitors. The Capless amplifier architecture provides a reference voltage to the headphone connector shield pin as shown in the middle drawing of Figure 31. The audio output signals are centered around this reference voltage, which is typically half of the supply voltage to allow symmetrical output voltage swing. When using a Capless amplifier do not connect the headphone jack shield to any ground reference or large currents will result. This makes Capless amplifiers ineffective for plugging non-headphone accessories into the headphone connector. Capless amplifiers are useful only with floating GND headphones. Conventional CO VOUT CO VOUT GND Capless VOUT VOUT GND VBIAS DirectPath™ VDD VOUT GND VSS Figure 31. Amplifier Applications The DirectPath™ amplifier architecture operates from a single supply voltage and uses an internal charge pump to generate a negative supply rail for the headphone amplifier. The output voltages are centered around 0 V and are capable of positive and negative voltage swings as shown in the bottom drawing of Figure 31. DirectPath amplifiers require no output dc-blocking capacitors. The headphone connector shield pin connects to ground and will interface with headphones and non-headphone accessories. The TPA6140A2 is a DirectPath amplifier. ELIMINATING TURN-ON POP AND POWER SUPPLY SEQUENCING The TPA6140A2 has excellent noise and turn-on / turn-off pop performance. It uses an integrated click-and-pop suppression circuit to allow fast start-up and shutdown without generating any voltage transients at the output pins. Typical start-up time from shutdown is 5 ms. DirectPath technology keeps the output dc voltage at 0 V even when the amplifier is powered up. The DirectPath technology together with the active pop-and-click suppression circuit eliminates audible transients during start up and shutdown. 15 Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): TPA6140A2 TPA6140A2 SLOS598 – MARCH 2009 .................................................................................................................................................................................................. www.ti.com Use input coupling capacitors to ensure inaudible turn-on pop. Activate the TPA6140A2 after all audio sources have been activated and their output voltages have settled. During power-down, deactivate the TPA6140A2 before deactivating the audio input source. RF AND POWER SUPPLY NOISE IMMUNITY The TPA6140A2 employs a new differential amplifier architecture to achieve high power supply noise rejection and RF noise rejection. RF and power supply noise are common in modern electronics. Although RF frequencies are much higher than the 20 kHz audio band, signal modulation often falls in-band. This, in turn, modulates the supply voltage, allowing a coupling path into the audio amplifier. A common example is the 217 Hz GSM frame-rate buzz often heard from an active speaker when a cell phone is placed nearby during a phone call. The TPA6140A2 has excellent rejection of power supply and RF noise, preventing audio signal degradation. INPUT COUPLING CAPACITORS Input coupling capacitors block any dc bias from the audio source and ensure maximum dynamic range. Input coupling capacitors also minimize TPA6140A2 turn-on pop to an inaudible level. The input capacitors are in series with TPA6140A2 internal input resistors, creating a high-pass filter. Equation 8 calculates the high-pass filter corner frequency. The input impedance, RIN, is dependent on device gain. Larger input capacitors decrease the corner frequency. See the Operating Characteristics table for input impedance values. 1 fC = 2pRINCIN (8) For a given high-pass cutoff frequency, the minimum input coupling capacitor is found as: 1 CIN = 2pfCRIN (9) Example: Design for a 20 Hz corner frequency with a TPA6140A2 gain of +6 dB. The Operating Characteristics table gives RIN as 13.2 kΩ. Equation 9 shows the input coupling capacitors must be at least 0.6 µF to achieve a 20 Hz high-pass corner frequency. Choose a 0.68 µF standard value capacitor for each TPA6140A2 input (X5R material or better is required for best performance). Input capacitors can be removed provided the TPA6140A2 inputs are driven differentially with less than ±1 VRMS and the common-mode voltage is within the input common-mode range of the amplifier. Without input capacitors turn-on pop performance may be degraded and should be evaluated in the system. CHARGE PUMP FLYING CAPACITOR AND HPVSS CAPACITOR The TPA6140A2 uses a built-in charge pump to generate a negative voltage supply for the headphone amplifiers. The charge pump flying capacitor connects between CPP and CPN. It transfers charge to generate the negative supply voltage. The HPVSS capacitor must be at least equal in value to the flying capacitor to allow maximum charge transfer. Use low equivalent-series-resistance (ESR) ceramic capacitors (X5R material or better is required for best performance) to maximize charge pump efficiency. Typical values are 1 µF to 2.2 µF for the HPVSS and flying capacitors. Although values down to 0.47 µF can be used, total harmonic distortion (THD) will increase. 16 Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): TPA6140A2 TPA6140A2 www.ti.com .................................................................................................................................................................................................. SLOS598 – MARCH 2009 POWER SUPPLY AND HPVDD DECOUPLING CAPACITORS AND CONNECTIONS The TPA6140A2 DirectPath headphone amplifier requires adequate power supply decoupling to ensure that output noise and total harmonic distortion (THD) remain low. Use good low equivalent-series-resistance (ESR) ceramic capacitors (X5R material or better is required for best performance). Place a 2.2 µF capacitor within 5 mm of the AVDD pin. Reducing the distance between the decoupling capacitor and AVDD minimizes parasitic inductance and resistance, improving TPA6140A2 supply rejection performance. Use 0402 or smaller size capacitors if possible. Ensure that the ground connection of each of the capacitors has a minimum length return path to the device. Failure to properly decouple the TPA6140A2 may degrade audio or EMC performance. For additional supply rejection, connect an additional 10 µF or higher value capacitor between AVDD and ground. This will help filter lower frequency power supply noise. The high power supply rejection ratio (PSRR) of the TPA6140A2 makes the 10 µF capacitor unnecessary in most applications. Connect a 2.2 µF capacitor between HPVDD and ground. This ensures the amplifier internal bias supply remains stable and maximizes headphone amplifier performance. WARNING: DO NOT connect HPVDD directly to AVDD or an external supply voltage. The voltage at HPVDD is generated internally. Connecting HPVDD to an external voltage can damage the device. LAYOUT RECOMMENDATIONS GND CONNECTIONS The SGND pin is an input reference and must be connected to the headphone ground connector pin. This ensures no turn-on pop and minimizes output offset voltage. Do not connect more than ±0.3 V to SGND. AGND is a power ground. Connect supply decoupling capacitors for AVDD, HPVDD, and HPVSS to AGND. GENERAL I2C OPERATION The I2C bus employs two signals, SDA (data) and SCL (clock), to communicate between integrated circuits in a system. The bus transfers data serially one bit at a time. The address and data 8-bit bytes are transferred most significant bit (MSB) first. In addition, each byte transferred on the bus is acknowledged by the receiving device with an acknowledge bit. Each transfer operation begins with the master device driving a start condition on the bus and ends with the master device driving a stop condition on the bus. The bus uses transitions on the data terminal (SDA) while the clock is at logic high to indicate start and stop conditions. A high-to-low transition on SDA indicates a start and a low-to-high transition indicates a stop. Normal data-bit transitions bust occur within the low time of the clock period. Figure 32 shows a typical sequence. The master generates the 7-bit slave address and the read/write (R/W) bit to open communication with another device and then waits for an acknowledge condition. The TPA6140A2 holds SDA low during the acknowledge clock period to indicate acknowledgment. When this occurs, the master transmits the next byte of the sequence. Each device is addressed by a unique 7-bit slave address plus R/W bit (1 byte). All compatible devices share the same signals via a bidirectional bus using a wired-AND connection. The TPA6140A2 operates as an I2C slave. The I2C voltage can not exceed the TPA6140A2 supply voltage, AVDD. An external pull-up resistor must be used for the SDA and SCL signals to set the logic high level for the bus. When the bus level is 3.3 V, use pull-up resistors between 660 Ω and 1.2 kΩ. 17 Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): TPA6140A2 TPA6140A2 SLOS598 – MARCH 2009 .................................................................................................................................................................................................. www.ti.com 8- Bit Data for Register (N) 8- Bit Data for Register (N+1) Figure 32. Typical I2C Sequence There is no limit on the number of bytes that can be transmitted between start and stop conditions. When the last word transfers, the master generates a stop condition to release the bus. A generic data transfer sequence is shown in Figure 32. SINGLE-AND MULTIPLE-BYTE TRANSFERS The serial control interface supports both single-byte and multi-byte read/write operations for all registers. During multiple-byte read operations, the TPA6140A2 responds with data, a byte at a time, starting at the register assigned, as long as the master device continues to respond with acknowledges. The TPA6140A2 supports sequential I2C addressing. For write transactions, if a register is issued followed by data for that register and all the remaining registers that follow, a sequential I2C write transaction has taken place. For I2C sequential write transactions, the register issued then serves as the starting point, and the amount of data subsequently transmitted, before a stop or start is transmitted, determines to how many registers are written. SINGLE-BYTE WRITE As shown in Figure 33, a single-byte data write transfer begins with the master device transmitting a start condition followed by the I2C device address and the read/write bit. The read/write bit determines the direction of the data transfer. For a write data transfer, the read/write bit must be set to 0. After receiving the correct I2C device address and the read/write bit, the TPA6140A2 responds with an acknowledge bit. Next, the master transmits the register byte corresponding to the TPA6140A2 internal memory address being accessed. After receiving the register byte, the TPA6140A2 again responds with an acknowledge bit. Finally, the master device transmits a stop condition to complete the single-byte data write transfer. Start Condition Acknowledge A6 A5 A4 A3 A2 A1 I2C Device Address and Read/Write Bit A0 R/W ACK A7 Acknowledge A6 A5 A4 A3 A2 A1 A0 ACK D7 Acknowledge D6 D5 Register D4 D3 Data Byte D2 D1 D0 ACK Stop Condition Figure 33. Single-Byte Write Transfer MULTIPLE-BYTE WRITE AND INCREMENTAL MULTIPLE-BYTE WRITE A multiple-byte data write transfer is identical to a single-byte data write transfer except that multiple data bytes are transmitted by the master device to the TPA6140A2 as shown in Figure 34. After receiving each data byte, the TPA6140A2 responds with an acknowledge bit. 18 Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): TPA6140A2 TPA6140A2 www.ti.com .................................................................................................................................................................................................. SLOS598 – MARCH 2009 Register Figure 34. Multiple-Byte Write Transfer SINGLE-BYTE READ As shown in Figure 35, a single-byte data read transfer begins with the master device transmitting a start condition followed by the I2C device address and the read/write bit. For the data read transfer, both a write followed by a read are actually done. Initially, a write is done to transfer the address byte of the internal memory address to be read. As a result, the read/write bit is set to a 0. After receiving the TPA6140A2 address and the read/write bit, the TPA6140A2 responds with an acknowledge bit. The master then sends the internal memory address byte, after which the TPA6140A2 issues an acknowledge bit. The master device transmits another start condition followed by the TPA6140A2 address and the read/write bit again. This time, the read/write bit is set to 1, indicating a read transfer. Next, the TPA6140A2 transmits the data byte from the memory address being read. After receiving the data byte, the master device transmits a not-acknowledge followed by a stop condition to complete the single-byte data read transfer. Repeat Start Condition Start Condition Acknowledge A6 A5 A1 A0 R/W ACK A7 I2C Device Address and Read/Write Bit Acknowledge A6 A5 A4 A0 ACK Not Acknowledge Acknowledge A6 A5 A1 A0 R/W ACK D7 D6 I2C Device Address and Read/Write Bit Register D1 D0 ACK Stop Condition Data Byte Figure 35. Single-Byte Read Transfer MULTIPLE-BYTE READ A multiple-byte data read transfer is identical to a single-byte data read transfer except that multiple data bytes are transmitted by the TPA6140A2 to the master device as shown in Figure 36. With the exception of the last data byte, the master device responds with an acknowledge bit after receiving each data byte. Repeat Start Condition Start Condition Acknowledge A6 A0 R/W ACK A7 I2C Device Address and Read/Write Bit Acknowledge A6 A5 Register A0 ACK Acknowledge A6 A0 R/W ACK D7 I2C Device Address and Read/Write Bit Acknowledge D0 ACK D7 First Data Byte Acknowledge Not Acknowledge D0 ACK D7 D0 ACK Other Data Bytes Last Data Byte Stop Condition Figure 36. Multiple-Byte Read Transfer 19 Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): TPA6140A2 TPA6140A2 SLOS598 – MARCH 2009 .................................................................................................................................................................................................. www.ti.com REGISTER MAP Table 1. Register Map BIT 7 BIT 6 1 REGISTER HP_EN_L HP_EN_R 0 BIT 5 0 BIT 4 0 BIT 3 0 BIT 2 Thermal BIT 1 SWS BIT 0 2 Mute_L Mute_R Volume[4] Volume[3] Volume[2] Volume[1] Volume[0] 0 3 0 0 0 0 0 0 HiZ_L HiZ_R 4 0 0 0 0 Version[3] Version[2] Version[1] Version[0] 5 RFT RFT RFT RFT RFT RFT RFT RFT 6 RFT RFT RFT RFT RFT RFT RFT RFT 7 RFT RFT RFT RFT RFT RFT RFT RFT 8 RFT RFT RFT RFT RFT RFT RFT RFT Bits labeled "Reserved" are reserved for future enhancements. They may not be written to. When read, they will show a "0" value. Bits labeled "RFT" are reserved for TI testing. Under no circumstances must any data be written to these registers. If read, these bits may assume any value. The TPA6140A2 I2C address is 0xC0 (binary 11000000) for writing an 0xC1 (binary 11000001) for reading. If a different I2C address is required, please contact your local TI representative. Fault Register (Address: 1) BIT Function Reset Value 7 HP_EN_L 0 6 HP_EN_R 0 5 0 0 4 0 0 3 0 0 2 0 0 1 Thermal 0 0 SWS 1 HP_EN_L Enable bit for the left-channel amplifier. Amplifier is active when bit is high. HP_EN_R Enable bit for the right-channel amplifier. Amplifier is active when bit is high. Thermal Bit sets to 1 to indicate thermal shutdown. Once temperature decreases below a safe level, the TPA6140A2 re-activates regardless of previous bit status. This bit is clear-on-read. SWS Software shutdown control. Set bit to 1 to initiate software shutdown. Set bit to 0 to activate charge-pump. SWS must remain at 0 for normal operation.Use SWS instead of HP_EN_L and HP_EN_R to ensure lowest current consumption and highest input to output signal attenuation when disabling the amplifier. Volume and Mute Register (Address: 2) BIT Function Reset Value 7 Mute_L 1 6 Mute_R 1 5 Volume[4] 0 4 Volume[3] 0 3 Volume[2] 0 2 Volume[1] 0 1 Volume[0] 0 0 0 0 Mute_L Left channel mute. Set bit to 1 to mute left channel. Mute_R Right channel mute. Set bit to 1 to mute right channel. Volume[5:0] Volume control byte. Set to 111110 for highest gain, 4 dB; set to 000000 for lowest gain, –59 dB 20 Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): TPA6140A2 TPA6140A2 www.ti.com .................................................................................................................................................................................................. SLOS598 – MARCH 2009 Output Impedance Register (Address: 3) BIT Function Reset Value 7 0 0 6 0 0 5 0 0 4 0 0 3 0 0 2 0 0 1 HiZ_L 0 0 HiZ_R 0 Reserved These bits are reserved for future enhancements. Do not write to these bits as writing to these bits may change device function. If read these bits may assume any value. HiZ_L Set to 1 to put left channel amplifier output in three-state high impedance mode. HiZ_R Set to 1 to put right channel amplifier output in three-state high impedance mode. I2C Address and Version Register (Address: 4) BIT Function Reset Value 7 0 0 6 0 0 5 0 0 4 0 0 3 Version[3] 0 2 Version[2] 0 1 Version[1] 0 0 Version[0] 0 Version[3:0] The version bits track the revision of the silicon. Valid values are 0000 for the first silicon TPA6140A2. Reserved for Test (Addresses: 5-8) BIT Function Reset Value RFT 7 RFT x 6 RFT x 5 RFT x 4 RFT x 3 RFT x 2 RFT x 1 RFT x 0 RFT x Reserved for Test. Do NOT write to these registers. VOLUME CONTROL Set the TPA6140A2 volume control through the I2C interface. Write to the Volume[5:0] byte at Register 2, Bits 5-0. Although the gain byte is a 6-bit word, only 32 steps are available. The least significant bit of the Volume[5:0] byte is treated as a don’t care bit. GAIN CONTROL BYTE: MUTE [7:6], VOLUME[5:0] NOMINAL GAIN GAIN CONTROL BYTE: MUTE [7:6], VOLUME[5:0] NOMINAL GAIN 11XXXXXX –80 dB 0010000x –11 dB 0000000x –59 dB 0010001x –10 dB 0000001x –55 dB 0010010x –9.0 dB 0000010x –51 dB 0010011x –8.0 dB 0000011x –47 dB 0010100x –7.0 dB 0000100x –43 dB 0010101x –6.0 dB 0000101x –39 dB 0010110x –5.0dB 0000110x –35 dB 0010111x –4.0 dB 0000111x –31 dB 0011000x –3.0 dB 0001000x –27 dB 0011001x –2.0 dB 0001001x –25 dB 0011010x –1.0 dB 0001010x –23 dB 0011011x +0.0 dB 0001011x –21 dB 0011100x +1.0 dB 0001100x –19 dB 0011101x +2.0 dB 0001101x –17 dB 0011110x +3.0 dB 0001110x –15 dB 0011111x +4.0 dB 0001111x –13 dB 21 Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): TPA6140A2 TPA6140A2 SLOS598 – MARCH 2009 .................................................................................................................................................................................................. www.ti.com OPERATING MODES HARDWARE SHUTDOWN Hardware shutdown is not available in the TPA6140A2. The SWS register (Software Shutdown) must be used to shutdown the amplifier. SOFTWARE SHUTDOWN Set software shutdown by writing a logic 1 in register 1, bit 0 (SWS bit). Software shutdown places the device in the lowest power state (see the Electrical Characteristics Table for values). Engaging software shutdown turns off the buck regulator and charge pump and disables the amplifier outputs. Write a logic 0 to the SWS bit to reactivate the device. Note that when the device is in SWS mode all registers will maintain their values. The HP_EN_L and HP_EN_R bits can be reset because a full word must be used when writing just one bit to the register. To ensure lowest current consumption and highest input to output signal attenuation, SWS must be used instead of HP_EN_L and HP_EN_R (set HP_EN_L and HP_EN_R to logic 1) when disabling both channels of the amplifier simultaneously. Set HP_EN_L and HP_EN_R to logic 1 before changing SWS from logic 0 to logic 1. MUTE MODE Set the Mute_L bit to 1 to mute the left channel output. Set the Mute_R bit to 1 to mute the right channel output. They are respectively located at Register 2, Bits 7 and 6. Mute attenuation is -80 dB, typical. Mute attenuation can only be guaranteed when the amplifier is operational (SWS = 0) and enabled (HP_EN_L or HP_EN_R = 1) HI-Z MODE HI-Z mode mutes the device and puts the amplifier outputs into a high impedance state. Use this configuration when the outputs of the TPA6140A2 share traces with other devices whose outputs may be active. Write a logic 1 in register 3, bits 0 and 1 to enable Hi-Z mode for the left and right outputs. Place a logic 0 in register 3, bits 0 and 1 to disable the Hi-Z state. The left and right outputs can be placed into a Hi-Z state individually. Note that to use the Hi-Z mode, the SWS bit must be equal to logic 0 (amplifier operational) and the output headphone amplifiers must NOT be enabled (HP_EN_L and HP_EN_R = 0). DEFAULT MODE AT START-UP On power-up, the TPA6140A2 initializes in the following conditions: • SWS = 1 (Shutdown mode) • HP_EN_L = HP_EN_R = 0 (Outputs disabled) • Hi-Z_L = Hi-Z_R = 0 (Hi-Z off) • Mute_L = Mute_R = 1 (Amplifiers muted) • VOLUME = –59 dB PACKAGE INFORMATION Package Dimensions The package dimensions for this YFF package are shown in the table below. See the package drawing at the end of this data sheet for more details. Table 2. YFF Package Dimensions Packaged Devices D E TPA6140A2YFF Min = 1530µm Max = 1590µm Min = 1530µm Max = 1590µm 22 Copyright © 2009, Texas Instruments Incorporated Product Folder Link(s): TPA6140A2 PACKAGE OPTION ADDENDUM www.ti.com 20-Apr-2009 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty TPA6140A2YFFR ACTIVE DSBGA YFF 16 3000 Green (RoHS & no Sb/Br) Call TI Level-1-260C-UNLIM TPA6140A2YFFT ACTIVE DSBGA YFF 16 250 Call TI Level-1-260C-UNLIM Green (RoHS & no Sb/Br) Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 8-Apr-2009 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel Diameter Width (mm) W1 (mm) TPA6140A2YFFR DSBGA YFF 16 3000 180.0 TPA6140A2YFFT DSBGA YFF 16 250 180.0 A0 (mm) B0 (mm) K0 (mm) P1 (mm) 8.4 1.71 1.71 0.81 4.0 8.0 Q1 8.4 1.71 1.71 0.81 4.0 8.0 Q1 Pack Materials-Page 1 W Pin1 (mm) Quadrant PACKAGE MATERIALS INFORMATION www.ti.com 8-Apr-2009 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPA6140A2YFFR DSBGA YFF 16 3000 220.0 220.0 34.0 TPA6140A2YFFT DSBGA YFF 16 250 220.0 220.0 34.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DLP® Products DSP Clocks and Timers Interface Logic Power Mgmt Microcontrollers RFID RF/IF and ZigBee® Solutions amplifier.ti.com dataconverter.ti.com www.dlp.com dsp.ti.com www.ti.com/clocks interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/lprf Applications Audio Automotive Broadband Digital Control Medical Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/medical www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2009, Texas Instruments Incorporated