TI TPS59650RSLR

TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
Dual-Channel (3-Phase CPU/2-Phase GPU) SVID, D-CAP+™ Step-Down Controller for
IMVP-7 VCORE with Two Integrated Drivers
FEATURES
APPLICATIONS
•
•
•
•
1
2
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Intel IMVP-7 Serial VID (SVID) Compliant
Supports CPU and GPU Outputs
CPU Channel One-Phase, Two-Phase, or
Three-Phase
One-Phase or Two-Phase GPU Channel
Full IMVP-7 Mobile Feature Set Including
Digital Current Monitor
8-Bit DAC with 0.250-V to 1.52-V Output Range
Optimized Efficiency at Light and Heavy Loads
VCORE Overshoot Reduction (OSR)
VCORE Undershoot Reduction (USR)
Accurate, Adjustable Voltage Positioning
8 Independent Frequency Selections per
Channel (CPU/GPU)
Patent Pending AutoBalance™ Phase
Balancing
Selectable 8-Level Current Limit
3-V to 28-V Conversion Voltage Range
Two Integrated Fast FET Drivers w/Integrated
Boost FET
Selectable Address (TPS59650 only)
Small 6 × 6 , 48-Pin, QFN, PowerPAD™
Package
IMVP-7 VCORE Applications for Adapter,
Battery, NVDC or 3-V, 5-V, and 12-V Rails
DESCRIPTION
The TPS51650 and TPS59650 are dual-channel, fully
SVID compliant IMVP-7 step-down controllers with
two integrated gate drivers. Advanced control
features such as D-CAP™+ architecture with
overlapping pulse support (undershoot reduction,
USR) and overshoot reduction (OSR) provide fast
transient response, lowest output capacitance and
high efficiency. All of these controllers also support
single-phase operation for light loads. The full
compliment of IMVP-7 I/O is integrated into the
controllers including dual PGOOD signals, ALERT
and VR_HOT. Adjustable control of VCORE slew rate
and voltage positioning round out the IMVP-7
features. In addition, the controllers' CPU channel
includes two high-current FET gate drivers to drive
high-side and low-side N-channel FETs with
exceptionally high speed and low switching loss. The
TPS51601 driver is used for the third phase of the
CPU and the two phases of the GPU channel.
These controllers are packaged in a space-saving,
thermally enhanced 48-pin QFN and are rated to
operate from –10°C to 105°C.
SIMPLIFIED APPLICATION
3-phase CPU
Controller
Processor
IMVP-7
SVID Interface
Internal
FET Driver
TPS51601
FET Driver
CPU Power Stage
VCC_CPU
GPU Power Stage
VCC_GFX
Internal
FET Driver
TPS51601
FET Driver
2-phase GPU
Controller
TPS51601
FET Driver
TPS51650
UDG-12003
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
D-CAP+, PowerPAD, D-CAP are trademarks of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2012, Texas Instruments Incorporated
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ORDERING INFORMATION (1) (2)
TA
ORDERABLE
NUMBER
PACKAGE
–10°C to 105°C
Plastic Quad Flat
Pack (QFN)
(2)
TRANSPORT
MEDIA
MINIMUM
QUANTITY
TPS51650RSLT
250
TPS51650RSLR
2500
48
TPS59650RSLT
–40°C to 105°C
(1)
PINS
Tape-and-reel
ECO PLAN
Green (RoHS and
no Sb/Br)
250
TPS59650RSLR
2500
For the most current package and ordering information see the Package Option Addendum at the end of this document, or see the TI
web site at www.ti.com.
Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.
ABSOLUTE MAXIMUM RATINGS (1) (2)
over operating free-air temperature range (unless otherwise noted)
MIN
Input voltage
Output voltage
Electrotatic discharge
TYP MAX UNIT
VBAT
–0.3
CSW1, CSW2
–6.0
32
CDH1 to CSW1; CDH2 to CSW2; CBST1 to CSW1; CBST2 to CSW2
–0.3
6.0
CTHERM, CCOMP, CF-IMAX, GF-IMAX, GCOMP, GTHERM,
V5DRV, V5
–0.3
6.0
COCP-R, CCSP1, CCSP2, CCSP3, CCSN1, CCSN2, CCSN3, CVFB,
CGFB, V3R3, VR_ON, VCLK, VDIO, SLEWA, GGFB, GVFB, GCSN1,
GCSP1, GOCP-R
–0.3
3.6
PGND
–0.3
0.3
VREF
–0.3
1.8
CPGOOD, ALERT, VR_HOT, GPGOOD
–0.3
3.6
CPWM3, GPWM1, GPWM2, GSKIP, CDL1, CDL2
–0.3
6.0
V
V
(HBM) QSS 009-105 (JESD22-A114A)
(CDM) QSS 009-147 (JESD22-C101B.01)
32
V
2
kV
500
V
Operating junction temperature, TJ
-40
125
°C
Storage temperature, Tstg
-55
150
°C
(1)
(2)
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values are with respect to the network ground terminal unless otherwise noted.
THERMAL INFORMATION
THERMAL METRIC
(1)
TPS51650
TPS59650
RSL
48 PINS
θJA
Junction-to-ambient thermal resistance
31.7
θJCtop
Junction-to-case (top) thermal resistance
19.8
θJB
Junction-to-board thermal resistance
7.1
ψJT
Junction-to-top characterization parameter
0.3
ψJB
Junction-to-board characterization parameter
7.1
θJCbot
Junction-to-case (bottom) thermal resistance
2.1
(1)
2
UNITS
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
RECOMMENDED OPERATING CONDITIONS
MIN
Input voltage
Output voltage
TYP
MAX
VBAT
–0.1
28
CSW1, CSW2
–3.0
30
CDH1 to CSW1; CDH2 to CSW2; CBST1 to CSW1; CBST2 to
CSW2
–0.1
5.5
V5DRV, V5
4.5
5.5
V3R3
3.1
3.5
–0.1
2.5
CTHERM, GTHERM
0.1
3.6
CF-IMAX, GF-IMAX, COCP-R, GOCP-R
0.1
1.7
CCSP1, CCSP2, CCSP3, CCSN1, CCSN2, CCSN3, CVFB, CGFB,
GGFB, GVFB, GCSN1, GCSP1, GCSN2, GCSP2
–0.1
1.7
VR_ON, VCLK, VDIO, SLEWA
–0.1
3.5
PGND
–0.1
0.1
VREF
–0.1
1.72
CPGOOD, ALERT, VR_HOT, GPGOOD,
–0.1
VV3R3
CPWM3, GPWM1, GSKIP, CDL1, CDL2
–0.1
VV5
TPS51650
–10
105
TPS59650
–40
105
CCOMP, GCOMP
Operating free air temperature, TA
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
UNIT
V
V
°C
3
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
ELECTRICAL CHARACTERISTICS
over recommended free-air temperature range, VV5 = VV5DRV = 5.0 V; VV3R3 = 3.3 V; VxGFB = VPGND = VGND, VxVFB = VCORE
(Unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
11.0
mA
SUPPLY: CURRENTS, UVLO AND POWER-ON RESET
IV5-5
V5 supply current CPU: 3-phase IV5+ IV5DRV , VVDAC < VxVFB < (VVDAC + 100 mV),
active GPU: 2-phase active
VR_ON = ‘HI’
7.5
IV5-3
V5 supply current CPU: 3-phase IV5+ IV5DRV, VVDAC < VxVFB < (VVDAC + 100 mV),
active GPU: OFF
VR_ON = ‘HI’, VGCSP2= 3.3 V
5.5
mA
IV5-PS3
V5 supply current CPU: 3-phase IV5+ IV5DRV, VVDAC < VxVFB < (VVDAC + 100 mV),
active GPU: 2-phase active (1)
VR_ON = ‘HI’, SetPS = PS3
5.5
mA
IV5STBY
V5DRV standby current
VR_ON = ‘LO’, IV5 + IV5DRV
10
20
µA
VUVLOH
V5 UVLO 'OK' Threshold
Ramp up, VR_ON=’HI’,
4.25
4.35
4.50
V
VUVLOL
V5 UVLO fault threshold
Ramp down, VR_ON = ’HI’,
3.95
4.10
4.30
V
VPORV5
V5 Power-ON Reset fault
latch (2)
1.2
1.9
2.5
V
IV3R3
V3R3 supply current
SVID bus idle, VR_ON = ‘HI’
0.5
1.0
mA
IV3R3SBY
V3R3 standby current
VR_ON = ‘LO’
10
µA
V3UVLOH
V3R3 UVLO 'OK' threshold
Ramp up, VR_ON=’HI’,
2.5
2.9
3.0
V
V3UVLOL
V3R3 UVLO fault threshold
Ramp down, VR_ON = ’HI’,
2.4
2.7
2.8
V
VPORV3R3
V3R3 Power-ON Reset fault
latch (2)
1.2
1.9
2.5
V
REFERENCES: DAC, VREF, VBOOT AND DRVL DISCHARGE FOR BOTH CPU AND GPU
VVIDSTP
VID step size
VDAC1
xVFB tolerance
VDAC2
xVFB tolerance
Change VID0 HI to LO to HI
5
mV
0.25 ≤ VxVFB ≤ 0.595V,
IxPU_CORE = 0 A, 0°C ≤ TA ≤ 85°C
TPS51650
–6
6
0.25 ≤ VxVFB ≤ 0.595V,
IxPU_CORE = 0 A,
–40°C ≤ TA ≤ 105°C
TPS59650
–7.5
7.5
0.6 ≤ VxVFB ≤ 0.995V,
IxPU_CORE = 0 A, 0°C ≤ TA ≤ 85°C
TPS51650
–5
5
0.6 ≤ VxVFB ≤ 0.995V,
IxPU_CORE = 0 A,
–40°C ≤ TA ≤ 105°C
TPS59650
–7.5
7.5
1.000V ≤ VxVFB ≤ 1.520 V,
IxPU_CORE = 0 A, 0°C ≤ TA ≤ 85°C
TPS51650
–0.5%
0.5%
1.000V ≤ VxVFB ≤ 1.520 V,
IxPU_CORE = 0 A,
–40°C ≤ TA ≤ 105°C
TPS59650
–0.75%
0.75%
mV
VVREF
VREF Output
4.5 V ≤ VV5 ≤ 5.5 V, IVREF= 0 A
VVREFSRC
VREF output source
0 µA ≤ IVREF ≤ 500 µA
VVREFSNK
VREF output sink
–500 µA ≤ IVREF ≤ 0 µA
0.1
4
mV
VDLDQ
DRVL discharge threshold
Soft-stop transistor turns on at this point.
200
300
mV
20
40
µA
1.655
1.700
–4
–0.1
1.745
V
mV
VOLTAGE SENSE: xVFB AND xGFB FOR BOTH CPU AND GPU
IxVFB
xVFB input bias current
VxVFB= 2 V, VxGFB= 0 V
IxGFB
xGFB input bias current
VxVFB= 2 V, VxGFB= 0 V
AGAINGND
xGFB/GND gain
(1)
(2)
4
-40
-20
µA
1
V/V
3-phase CPU goes to 1-phase in PS3 2-phase GPU goes to 1-phase in PS3
Specified by design. Not production tested.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
over recommended free-air temperature range, VV5 = VV5DRV = 5.0 V; VV3R3 = 3.3 V; VxGFB = VPGND = VGND, VxVFB = VCORE
(Unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
9.2
UNIT
CURRENT SENSE: OVERCURRENT, ZERO CROSSING, VOLTAGE POSITIONING AND PHASE BALANCING
RxOCP-R = 20 kΩ
RxOCP-R = 24 kΩ
RxOCP-R = 30 kΩ
RxOCP-R = 39 kΩ
VOCPP
OCP voltage (valley current
limit)
RxOCP-R = 56 kΩ
RxOCP-R = 75 kΩ
RxOCP-R = 100 kΩ
RxOCP-R = 150 kΩ
TPS51650
4.6
7.0
TPS59650
3.9
7.0
9.2
TPS51650
7.6
10.0
12.1
TPS59650
6.7
10.0
12.1
TPS51650
11.6
14.0
16.2
TPS59650
11.0
14.0
16.2
TPS51650
16.5
19.0
21.2
TPS59650
15.6
19.0
21.2
TPS51650
22.3
25.0
27.2
TPS59650
21.2
25.0
27.2
TPS51650
29.2
32.0
34.5
TPS59650
28.3
32.0
34.5
TPS51650
37.1
40.0
42.5
TPS59650
35.6
40.0
42.5
TPS51650
46.1
49.0
51.9
TPS59650
45.6
49.0
51.9
VIMAX_MIN = 133 mV, value of xIMAX,
VIMAX = VREF × IMAX / 255
20
VIMAX
IMAX values both channels
ICS
CS pin input bias current
CSPx and CSNx
IxVFBDQ
xVFB input bias current,
discharge
End of soft-stop, xVFB = 100 mV
GM-DROOP
Droop amplifier
transconductance
xVFB = 1 V
IBAL_TOL
Internal current share tolerance
(VCSP1 – VCSN1) = (VCSP2 – VCSN2) =
(VCSP3 – VCSN3) = VOCPP_MIN
ACSINT
Internal current sense gain
Gain from CSPx – CSNx to PWM comparator
VIMAX_MAX = 653mV, value of xIMAX
Copyright © 2012, Texas Instruments Incorporated
mV
A
98
A
–1.0
0.2
1.0
µA
90
125
180
µA
TPS51650
486
497
518
TPS59650
480
497
518
–3%
11.65
µS
+3%
12.00
12.30
Submit Documentation Feedback
V/V
5
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
over recommended free-air temperature range, VV5 = VV5DRV = 5.0 V; VV3R3 = 3.3 V; VxGFB = VPGND = VGND, VxVFB = VCORE
(Unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
TIMERS: SLEW RATE, ISLEW, ADDR, ON-TIME AND I/O TIMING
tSTARTUP1
Start-up time
VBOOT > 0 V, SLEWRATE = 12 mV/µs, no faults,
time from VR_ON until the controller responds to
SVID commands
SLSTRTSTP
xVFB slew soft-start / soft-stop
SLEWRATE = 12mV/µs, VR_ON goes ‘HI’,
VR_ON goes ‘LO = ‘Soft-stop’
1.25
1.50
1.75
VSLEWA ≤ 0.30V (Also disables SVID CLK timer)
10.0
12.0
14.5
3
4
5
5
VSLEWA = 0.4 V
VSLEWA = 0.6 V
SLSET
Slew rate setting
0.75 V ≤ VSLEWA ≤ 0.85 V
VSLEWA = 1.2 V
20
VSLEWA = 1.4 V
23
VSLEWA = 1.6 V
26
xPGOOD deglitch time
tPGDDGLTU
xPGOOD deglitch time
Time from xVFB out of -315 mV VDAC boundary
to xPGOOD low.
mV/µs
mV/µs
5
15
µs
50
100
µs
RCF= 20 kΩ, VBAT= 12 V,
VDAC= 1.1 V (250 kHz)
TPS51650
300
317
340
TPS59650
298
317
340
RCF= 24 kΩ, VBAT= 12 V,
VDAC= 1.1 V (300 kHz)
TPS51650
245
261
284
TPS59650
243
261
284
RCF= 30 kΩ, VBAT= 12 V,
VDAC= 1.1 V (350 kHz)
TPS51650
210
223
242
TPS59650
208
223
242
RCF= 39 kΩ, VBAT= 12 V,
VDAC= 1.1 V (400 kHz)
TPS51650
184
196
216
TPS59650
181
196
216
RCF= 56 kΩ, VBAT= 12 V,
VDAC= 1.1 V (450 kHz)
TPS51650
169
181
201
TPS59650
166
181
201
RCF= 75 kΩ, VBAT= 12 V,
VDAC= 1.1 V (500 kHz)
TPS51650
153
164
184
TPS59650
150
164
184
RCF= 100 kΩ, VBAT= 12 V,
VDAC= 1.1 V (550 kHz)
TPS51650
140
151
171
TPS59650
137
151
171
RCF= 150 kΩ, VBAT= 12 V,
VDAC= 1.1 V (600 kHz)
TPS51650
130
140
160
TPS59650
127
140
160
CPU on-time
Submit Documentation Feedback
10
14.5
16
tPGDDGLTO
6
8
12.0
VSLEWA = 1.0 V
Time from xVFB out of +220 mV VDAC boundary
to xPGOOD low.
tTON_CPU
7
10.0
ms
ns
Copyright © 2012, Texas Instruments Incorporated
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
over recommended free-air temperature range, VV5 = VV5DRV = 5.0 V; VV3R3 = 3.3 V; VxGFB = VPGND = VGND, VxVFB = VCORE
(Unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
TIMERS: SLEW RATE, ISLEW, ADDR, ON-TIME AND I/O TIMING (Continued)
tTON_GPU
RGF= 20 kΩ, VBAT= 12 V,
VDAC= 1.1 V (275 kHz)
TPS51650
282
323
377
TPS59650
280
323
377
RGF= 24 kΩ, VBAT= 12 V,
VDAC= 1.1 V (330 kHz)
TPS51650
233
270
319
TPS59650
231
270
319
RGF= 30 kΩ, VBAT= 12 V,
VDAC= 1.1 V (385 kHz)
TPS51650
208
236
280
TPS59650
205
236
280
RGF= 39 kΩ, VBAT= 12 V,
VDAC= 1.1 V (440 kHz)
TPS51650
185
210
248
TPS59650
182
210
248
RGF= 56 kΩ, VBAT= 12 V,
VDAC= 1.1 V (495 kHz)
TPS51650
172
195
230
TPS59650
169
195
230
RGF= 75 kΩ, VBAT= 12 V,
VDAC= 1.1 V (550 kHz)
TPS51650
158
178
211
TPS59650
154
178
211
RGF= 100 kΩ, VBAT= 12 V,
VDAC= 1.1 V (605 kHz)
TPS51650
147
166
203
TPS59650
145
166
203
RGF= 150 kΩ, VBAT= 12 V,
VDAC= 1.1 V (660 kHz)
TPS51650
141
157
193
TPS59650
134
157
193
150
225
GPU on-time
tMIN
Controller minimum off time
Fixed value
tVCCVID
VID change to xVFB change (3)
ACK of SetVID-x command to start of voltage
ramp
tVRONPGD
VR_ON low to xPGOOD low
tVRTDGLT
VR_HOT deglitch time
RSFTSTP
Soft-stop transistor resistance
Connect to CVFB, GVFB
500
ns
µs
2
60
ns
100
ns
0.2
0.5
ms
740
1100
Ω
PROTECTION: OVP, UVP PGOOD, VR_HOT, ‘FAULTS OFF’ AND INTERNAL THERMAL SHUTDOWN
VOVPH
Fixed OVP voltage threshold
voltage
VCSN1 or VGCSN > VOVPH for 1 µs, DRVL → ON
1.67
1.72
1.77
V
VPGDH
xPGOOD high threshold
Measured at the xVFB pin wrt/VID code,
device latches OFF
190
220
245
mV
VPGDL
xPGOOD low threshold
Measured at the xVFB pin wrt/VID code,
device latches OFF
–348
–315
–278
mV
bit0 of xTHERM register = high
755
783
810
bit1 of xTHERM register also is high
657
680
707
bit2 of xTHERM register also is high
611
638
665
bit3 of xTHERM register also is high
569
598
624
bit4 of xTHERM register also is high
532
559
585
bit5 of xTHERM register also is high
498
523
549
bit6 of xTHERM register also is high,
ALERT goes low
462
455
514
bit7 of xTHERM register also is high,
VR_HOT goes low
430
455
481
410
428
VTHERM
IMVP-7 thermal bit voltage
definition
CDLx goes low, CDHx goes low
373
ITHRM
THERM current
Leakage current, VxTHERM = 1 V
–2
THINT
Internal controller thermal
Shutdown (3)
Latch off controller
THHYS
Controller thermal SD
hysteresis (3)
Cooling required before converter can be reset
(3)
2
mV
µA
155
°C
20
°C
Specified by design. Not production tested.
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
7
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
over recommended free-air temperature range, VV5 = VV5DRV = 5.0 V; VV3R3 = 3.3 V; VxGFB = VPGND = VGND, VxVFB = VCORE
(Unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
4
8
13
Ω
36
50
Ω
0.2
2
µA
0.45
V
LOGIC (VCLK, VDIO, ALERT, VR_HOT, VR_ON) INTERFACE PINS: I/O VOLTAGE AND CURRENT
VDIO, ALERT, VR_HOT, pull-down resistance at
0.31 V
RRSVIDL
Open drain pull down resistance
RRPGDL
Open drain pull down resistance xPGOOD pull-down resistance at 0.31 V
IVRTTLK
Open drain leakage current
VR_HOT, xPGOOD, Hi-Z leakage,
apply 3.3-V in off state
VIL
Input logic low
VCLK, VDIO
VIH
Input logic high
VCLK, VDIO
VHYST
Hysteresis voltage
VVR_ONL
VR_ON logic low
VVR_ONH
VR_ON logic high
IVR_ONH
I/O 3.3 V leakage
-2
0.65
(4)
V
50
mV
0.3
V
25
µA
0.8
Leakage current , VVR_ON = 1.1 V
V
8
OVERSHOOT AND UNDERSHOOT REDUCTION (OSR/USR) THRESHOLD SETTING
OSR voltage set (COCP-R pin
for CPU GOCP-R for GPU)
VOSR
USR voltage set (COCP-R pin
for CPU GOCP-R for GPU)
VUSR
VXOCP-R = 0.2 V
106
VXOCP-R = 0.4 V
156
VXOCP-R = 0.6 V
207
VXOCP-R = 0.8 V
257
VXOCP-R = 1.0 V
308
VXOCP-R = 1.2 V
409
VXOCP-R = 1.4 V
510
VXOCP-R = 1.6 V
610
VXOCP-R = 0.2 V
40
VXOCP-R = 0.4 V
60
VXOCP-R = 0.6 V
80
VXOCP-R = 0.8 V
120
VXOCP-R = 1.0 V
160
VXOCP-R = 1.2 V
200
VXOCP-R = 1.4 V
240
VXOCP-R = 1.6 V
OFF
VOSR_ON/V USR enabled (both CPU and
GPU)
USR_ON
GSKIP voltage at start-up
VUSR_OFF
USR OFF setting (both CPU
and GPU)
GSKIP voltage at start-up
0.4
VOSR_OFF
OSR OFF setting (both CPU
and GPU)
GSKIP voltage at start-up
1.4
VOSRHYS
OSR/USR voltage hysteresis
(4)
(5)
8
(5)
All settings
mV
mV
0.15
1.1
5
V
mV
Specified by design. Not production tested.
Specified by design. Not production tested.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
over recommended free-air temperature range, VV5 = VV5DRV = 5.0 V; VV3R3 = 3.3 V; VxGFB = VPGND = VGND, VxVFB = VCORE
(Unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
(VCBSTx – VCSWx) = 5 V, ‘HI’ state,
(VVBST – VVDRVH) = 0.25 V
1.2
2.5
(VCBSTx – VCSWx) = 5 V, ‘LO’ state,
(VDRVH – VCSWx) = 0.25 V
0.8
2.5
VCDHx = 2.5 V, (VCBSTx – VCSWx) = 5 V, Source
2.2
VCDHx = 2.5 V, (VCBSTx – VCSWx) = 5 V, Sink
2.2
UNIT
DRIVERS: HIGH-SIDE, LOW-SIDE, CROSS CONDUCTION PREVENTION AND BOOST RECTIFIER
RDRVH
IDRVH
tDRVH
DRVH On-resistance
DRVH sink/source current (6)
DRVH transition time
RDRVL
DRVL ON resistance
IDRVL
DRVL sink/source current (6)
tDRVL
DRVL transition time
tNONOVLP
Driver non overlap time
RDS(on)
IBSTLK
Ω
CDHx 10% to 90% or 90% to 10%, CCDHx = 3 nF
A
A
15
40
ns
ns
15
40
‘HI’ State, (VV5DRV – VVDRVL) = 0.25 V
0.9
2
‘LO’ State, (VVDRVL – VPGND)= 0.2 V
0.4
1
VCDLx = 2.5 V, Source
2.7
VCDLx = 2.5 V, Sink
Ω
A
6
A
VCDLx 90% to 10%, CCDLx = 3 nF
15
40
VCDLx 10% to 90%, CCDLx = 3 nF
15
40
ns
VCSWx falls to 1 V to VCDLx rises to 1 V
8
25
CDLx falls to 1 V to CDHx rises to 1 V
8
25
BST on-resistance
(VV5DRV – VVBST), IF = 5 mA
5
10
22
Ω
BST switch leakage current
VVBST = 34 V, VCSWx= 28 V
0.1
1
µA
0.3
V
ns
PWM and SKIP OUTPUT: I/O Voltage and Current
VPWML
xPWMy output low level
VPWMH
xPWMy output high level
VSKIPL
xSKIP low-level output voltage
VSKIPH
xSKIP high-level output voltage
VPW(leak)
xPWM leakage
(6)
4.2
V
0.3
V
0.1
µA
4.2
Tri-state, VxPWMx = 5 V
V
Specified by design. Not production tested.
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
9
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
DEVICE INFORMATION
V5
CDH1
CBST1
CSW1
CDL1
V5DRV
PGND
CDL2
CSW2
CBST2
CDH2
VBAT
48
47
46
45
44
43
42
41
40
39
38
37
RSL PACKAGE
48 PINS
(TOP VIEW)
CTHERM
1
36
CPWM3
COCP-R
2
35
GPWM2
CF-IMAX
3
34
GPWM1
CCSP1
4
33
GSKIP
CCSN1
5
32
GTHERM
CCSN2
6
31
GCSN2
TPS51650
CCSP2
7
30
GCSP2
CCSP3
8
29
GCSP1
CCSN3
9
28
GCSN1
CCOMP
10
27
GCOMP
CVFB 11
26
GVFB
CGFB
25
GGFB
23
24
GF-IMAX
19
ALERT
GPGOOD
18
VCLK
22
17
CPGOOD
SLEWA
16
VR_ON
VR)HOT 21
15
V3R3
20
14
VREF
VDIO
13
GOCP-R
12
PIN FUNCTIONS
PIN
I/O
DESCRIPTION
NAME
NO.
ALERT
19
O
SVID interrupt line, open drain. Route between VCLK and VDIO to prevent cross-talk.
CBST1
46
I
Top N-channel FET bootstrap voltage input for CPU phase 1.
CBST2
39
I
Top N-channel bootstrap voltage input for CPU phase 2.
CCSN1
5
CCSN2
6
I
Negative current sense inputs for the CPU converter. Connect to the most negative node of current sense
resistor or inductor DCR sense network. CCSN1 has a secondary OVP comparator.
O
Output of GM error amplifier for the CPU converter. A resistor to VREF sets the droop gain.
I
Positive current sense inputs for the CPU converter. Connect to the most positive node of current sense resistor
or inductor DCR sense network. Tie CCSP3, 2 or 1 (in that order) to V3R3 to disable the phase. Tie CCSP1 to
V3R3 to run the GPU converter only.
CCSN3
9
CCOMP
10
CCSP1
4
CCSP2
7
CCSP3
8
CDH1
47
O
Top N-channel FET gate drive output for CPU phase 1.
CDH2
38
O
Top N-channel FET gate drive output for CPU phase 2.
CDL1
44
O
Synchronous N-channel FET gate drive output for CPU phase 1.
CDL2
41
O
Synchronous N-channel FET gate drive output for CPU phase 2.
10
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
PIN
NAME
NO.
I/O
DESCRIPTION
CF-IMAX
3
I
Voltage divider to VREF. A resistor to GND sets the operating frequency of the CPU converter. The voltage level
sets the maximum operating current of the CPU converter. The IMAX value is an 8-bit A/D where VIMAX = VREF ×
IMAX / 255. Both are latched at start-up.
CGFB
12
I
Voltage sense return tied for the CPU converter. Tie to GND with a 10-Ω resistor to close feedback when the
microprocessor is not in the socket.
COCP-R
2
I
Resistor to GND (RCOCP) selects 1 of 8 OCP levels (per phase, latched at start-up) of the CPU converter. Also,
voltage on this pin sets 1 of 8 USR/OSR levels for CPU converter.
CPGOOD
17
O
IMVP-7_PWRGD output for the CPU converter. Open-drain.
CSW1
45
I/O Top N-channel FET gate drive return for CPU phase 1.
CSW2
40
I/O Top N-channel FET gate drive return for CPU phase 2.
CPWM3
36
O
PWM control for the external driver, 5V logic level.
CTHERM
1
I/O
Thermal sensor connection for the CPU converter. A resistor connected to VREF forms a divider with an NTC
thermistor connected to GND.
CVFB
11
I
Voltage sense line tied directly to VCORE of the CPU converter. Tie to VCORE with a 10-Ω resistor to close
feedback when µP is not in the socket. The soft-stop transistor is on this pin
GCOMP
27
O
Output of gM error amplifier for the GPU converter. A resistor to VREF sets the droop gain.
GCSN1
28
I
GCSN2
31
I
Negative current sense input for the GPU converter. Connect to the most negative node of current sense resistor
or inductor DCR sense network.
GCSP1
29
I
GCSP2
30
I
GGFB
25
I
24
I
Voltage divider to VREF. R to GND sets the operating frequency of the GPU converter. The voltage level sets
the maximum operating current of the GPU converter. The IMAX value is an 8-bit A/D where VIMAX = VREF ×
IMAX / 255. Both are latched at start-up.
13
I
Resistor to GND (RGOCP) selects 1 of 8 OCP levels (per phase, latched at start-up) of the GPU converter. Also,
voltage on this pin sets 1 of 8 USR/OSR levels for GPU converter.
GPGOOD
23
O
IMVP-7_PWRGD output for the GPU converter. Open-drain.
GPWM1
34
O
PWM control input for the external driver for the two phases of GPU channel (5-V logic level).
GPWM2
35
O
33
O
32
I/O Thermal sensor input for the GPU converter. A resistor connected to VREF forms a divider with an NTC
thermistor connected to GND.
GF-IMAX
GOCP-R
GSKIP
GTHERM
GVFB
PGND
V5DRV
V3R3
VBAT
Voltage sense return tied for the GPU converter. Tie to GND with a 10-Ω resistor to close feedback when the
microprocessor is not in the socket.
Skip mode control of the external driver for the GPU converter; 5-V logic level. Logic HI = FCCM; LO = SKIP. A
defined voltage level on this pin at start-up can turn OSR OFF or USR OFF.
26
I
Voltage sense line tied directly to VGFX of the GPU converter. Tie to VGFX with a 10-Ω resistor to close feedback
when the microprocessor is not in the socket. The soft-stop transistor is on this pin
42
–
Synchronous N-channel FET gate drive return.
22
I
The voltage at start-up sets 1 of 7 slew rates for both converters. The SLOW rate is SLEWRATE/4. Soft-start
and soft-stop rates are SLEWRATE/8. This value is latched at start-up. For TPS59650, the resistor to GND sets
the base SVID address.
48
I
5-V power input for analog circuits; connect through resistor to 5-V plane and bypass to GND with ≥1 µF ceramic
capacitor
43
I
Power input for the gate drivers; connected with an external resistor to V5F; decouple with a ≥2.2 µF ceramic
capacitor.
15
I
3.3-V power input; bypass to GND with ≥1 µF ceramic cap.
37
I
Provides VBAT information to the on-time circuits for both converters. A 10-kΩ series resistor protects the
adjacent pins from inadvertent shorts due to solder bridges or mis-probing during test.
I
SVID clock. 1-V logic level.
SLEWA
V5
Positive current sense input for the GPU converter. Connect to the most positive node of current sense resistor
or inductor DCR sense network. Tie GCSP2 to V3R3 to disable the phase. Tie GCSP1 and GCSP2 to V3R3 to
disable completely the GPU converter.
VCLK
18
VDIO
20
I/O SVID digital I/O line. 1-V logic level.
VREF
14
O
1.7-V, 500-µA reference. Bypass to GND with a 0.22-µF ceramic capacitor.
VR_ON
16
I
IMVP-7 VR enable; 1V I/O level; 100-ns de-bounce. Regulator enters controlled soft-stop when brought low.
21
O
IMVP-7 thermal flag open drain output – active low. Typically pulled up to 1-V logic level through 56 Ω. Fall time
< 100 ns. 1-ms de-glitch using consecutive 1-ms samples.
VR_HOT
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
11
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
PIN
NAME
NO.
PAD
GND
12
www.ti.com
I/O
–
DESCRIPTION
Thermal pad and analog circuit reference; tie to a quiet area in the system ground plane with multiple vias.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
TYPICAL CHARACTERISTICS
3-Phase Configuration, 94-A CPU
1.10
0.70
PS = PS0
VVID = 1.05 V
1.00
0.95
0.90
VIN = 9 V
VIN =20 V
Spec Maximum
Spec Minimum
0.85
0.80
0
10
20
30
40
50
60
70
Output Current (A)
0.65
Output Voltage (V)
Output Voltage (V)
1.05
0.60
0.57
0.55
0.53
80
90
0.50
100
0
2
4
6
G001
8
10
12
14
Output Current (A)
16
18
20
G002
Figure 2. Output Voltage vs. Load Current in PS1
95
95
PS = PS0
VVID = 1.05 V
90
85
80
75
70
10
20
30
40
50
60
Output Current (A)
70
80
85
80
75
70
VIN = 9 V
VIN = 20 V
0
PS = PS1
VVID = 0.6 V
90
Efficiency (%)
Efficiency (%)
PS = PS1
VVID = 0.6 V
0.62
Figure 1. Output Voltage vs. Load Current in PS0
65
VIN = 9 V
VIN =20 V
Spec Maximum
Spec Minimum
0.68
90
G003
65
VIN = 9 V
VIN = 20 V
0
2
4
6
8
10
12
14
Output Current (A)
16
18
Figure 3. Efficiency vs. Load Current in PS0
Figure 4. Efficiency vs. Load Current in PS1
Figure 5. Switching Ripple in PS0, VIN = 9 V
Figure 6. Switching Ripple in PS0, VIN = 20 V
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
20
G004
13
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
TYPICAL CHARACTERISTICS
3-Phase Configuration, 94-A CPU (continued)
14
Figure 7. Load Transient: VIN = 9 V , Load-step = 66 A
Figure 8. Load Transient, VIN = 20 V, Load step = 66 A
Figure 9. Load Transient, VIN = 9 V, Load step = 66 A
Figure 10. Load Transient, VIN = 20 V, Load step = 66 A
Figure 11. Start-Up and PGOOD
Figure 12. Soft-Stop
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
TYPICAL CHARACTERISTICS
3-Phase Configuration, 94-A CPU (continued)
Figure 13. Dynamic VID: VIN = 20 V, SetVIDSlow = 0.6 V,
SetVIDSlow = 1.05 V
Figure 14. Dynamic VID: VIN = 20 V, SetVIDFast = 0.6 V,
SetVIDFast = 1.05 V
Figure 15. Dynamic VID: VIN = 20 V, SetVIDDecay = 0.6 V,
SetVIDFast = 1.05 V
Figure 16. PS Change: VIN = 20 V, PS0 to PS1 Toggle
135
20
90
10
45
0
0
−10
−45
−20
−90
−30
−135
−40
−50
100
GAIN
PHASE
−180
1k
−225
1M
10k
Frequency (Hz)
100k
Figure 17. Gain-Phase Bode Plot
Copyright © 2012, Texas Instruments Incorporated
0.0040
Magnitude
Phase
Target
180
135
0.0035
Magnitude (Ω)
Magnitude (dB)
30
225
0.0045
180
Phase (°)
VIN = 20 V
40
90
0.0030
45
0.0025
0
0.0020
−45
−90
0.0015
−135
0.0010
0.0005
100
G005
Phase (°)
225
50
−180
1k
10k
Frequency (Hz)
100k
−225
1M
G006
Figure 18. Output Impedance
Submit Documentation Feedback
15
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
TYPICAL CHARACTERISTICS
2-Phase Configuration, 46-A GPU
1.2500
0.6500
PS = PS0
VVID = 1.23 V
0.6250
Output Voltage (V)
Output Voltage (V)
1.2000
1.1500
1.1000
VIN = 9 V
VIN =20 V
Spec Maximum
Spec Minimum
1.0500
1.0000
0
5
10
15
20
25
30
35
Output Current (A)
0.6000
0.5750
0.5500
40
45
50
0.5000
2
4
6
8
10
12
14
Output Current (A)
16
18
20
G008
Figure 20. Output Voltage Vs. Load Current in PS0
95
PS = PS0
VVID = 1.23 V
PS = PS1
VVID = 0.6 V
90
95
85
Efficiency (%)
Efficiency (%)
0
G007
100
90
85
80
75
70
65
80
VIN = 9 V
VIN = 20 V
16
VIN = 9 V
VIN =20 V
Spec Maximum
Spec Minimum
0.5250
Figure 19. Output Voltage Vs. Load Current in PS0
75
PS = PS1
VVID = 0.6 V
0
5
10
15
20
25
30
35
Output Current (A)
40
45
VIN = 9 V
VIN = 20 V
60
50
G009
55
0
2
4
6
8
10
12
14
Output Current (A)
16
18
Figure 21. Efficiency Vs. Load Current in PS0
Figure 22. SEfficiency Vs. Load Current in PS0
Figure 23. Switching Ripple in PS0, VIN = 9 V
Figure 24. Switching Ripple in PS0, VIN = 20 V
Submit Documentation Feedback
20
G010
Copyright © 2012, Texas Instruments Incorporated
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
TYPICAL CHARACTERISTICS
2-Phase Configuration, 46-A GPU (continued)
Figure 25. Load Transient, VIN = 9 V, Load Step = 37 A
Figure 26. Load Transient, VIN = 20 V, Load Step = 37 A
Figure 27. Load Transient, VIN = 9 V, Load Step = 37 A
Figure 28. Load Transient, VIN = 20 V, Load Step = 37 A
Figure 29. Start-Up and PGOOD
Figure 30. Soft-Stop
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
17
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
TYPICAL CHARACTERISTICS
2-Phase Configuration, 46-A GPU (continued)
Figure 31. Dynamic VID: VIN = 20 V, SetVIDSlow = 0.6 V,
SetVIDSlow = 1.05 V
Figure 32. Dynamic VID: VIN = 20 V, SetVIDDecay = 0.6 V,
SetVIDFast = 1.05 V
Figure 33. Dynamic VID: VIN = 20 V, SetVIDDecay = 0.6 V,
SetVIDFast 1.05 V
Figure 34. PS Change: VIN = 20 V, PS0 to PS1 Toggle
225
VIN = 20 V
Magnitude (dB)
40
180
30
135
20
90
10
45
0
0
−10
−45
−20
−90
−135
−30
−40
−50
100
Phase (°)
50
GAIN
PHASE
1k
−180
10k
Frequency (Hz)
100k
−225
1M
G011
Figure 35. Output Impedance
18
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
FUNCTIONAL BLOCK DIAGRAM
CCOMP
10
+
CVFB 11
A
4
Gm
+
5
CCSP2
6
7
CCSP3
8
43 V5DRV
46 CBST1
CLK
Phase
Manager
CLK2
CLK3
On-Time
2
47 CDH1
Smart
Driver
45 CSW1
44 CDL1
USR
OSR/USR
+
Current
Sharing
Circuitry
+
+
?
39 CBST2
ISHARE
+
+
42 PGND
On-Time
3
OSR
IS2
COCP
CPx
CVD
GISUM
GIS1
GIS2
GIS3
IS3
Acs
CCSN3
+
+
Error
Amplifier
Integrator
IS1
Acs
CCSN2
On-Time
1
CLK1
DAC0
Acs
CCSN1
CF-IMAX
+
CGFB 12
CCSP1
CPWM1
CPWM2
CPWM3
Ramp
Comparator
9
38 CDH2
Smart
Driver
40 CSW2
CPU
Logic Protection
and Status Circuitry
41 CDL2
36 CPWM3
GCOMP 27
+
GVFB 26
CPWM1
CPWM2
CPWM3
Ramp
Comparator
A
CF-IMAX
Gm
GCSP1 29
Error
Amplifier
Integrator
DAC0
+
Acs
34 GPWM1
On-Time
2
35 GPWM2
CLK1
+
GGFB 25
On-Time
1
IS1
+
+
GCSN1 28
CLK
Phase
Manager
CLK2
USR
OSR/USR
GCSP2 30
+
Acs
OSR
IS2
Current
Sharing
Circuitry
+
GCSN2 31
+
?
GOCP
GPx
GVD
GISUM
GIS1
GIS2
VR_ON 16
CPGOOD 17
DAC0
and
DAC1
VCLK 18
33 GSKIP
ISHARE
DAC0
CPU
Logic Protection
and Status Circuitry
DAC1
ALERT 19
VDIO 20
SVID
Interface
VR_HOT 21
GPGOOD 23
1
32
SLEWA
GF-IMAX
CTHERM
GTHERM
2
13
14
15
48
Pad
VREF
24
COCP-R
3
GOCP-R
22
CF-IMAX
TPS51650
TPS59650
V3R3
V5
GND
Copyright © 2012, Texas Instruments Incorporated
UDG-12016
Submit Documentation Feedback
19
TPS51650, TPS59650
3R3V
VREF
VREF
VREF
VREF
VR_ON
CPGOOD
VCLK
VDIO
ALERT
VR_HOT
GPGOOD
VREF
VREF
GFX_GSNS
CPU_GSNS
GFX_VSNS
CPU_VSNS
GSCN1
CCSN3
GSCP1
CCSP3
GCSP2
CCSP2
GCSN2
CCSN2
VREF
GSKIP
CPWM3
GPWM2
VREF
GPWM1
VCLK
VDIO
ALERT
VREF
VREF
V5
V5
V5DRV
VCCIO
VBAT
V5DRV
VCCIO
VIN
VIN
1
1
CPU: QC
I_CC_max = 94A
I_TDC = 52A
I_DYN_max = 66A
Min. Over Current Limit = 110A
Loadline = 1.9mohm
Frequency setting = 300kHz
2
2
+
CCSP1
CCSN1
CCSN2
CCSP2
VCC_CORE
GFX: GT2
I_cc_max = 46A
I_TDC = 37A
I_DYNAMIC = 38A
Min. Over Current Limit = 52A
Loadline = 3.9mohm
Frequency setting = 388kHz
Note:
VR_HOT, CPGOOD and GPGOOD are open drain outputs.
If used, they would need pull-up resistors.
To CPU SVID
SVID:ALERT
SVID:CLK
SVID:DATA
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
20
www.ti.com
SLUSAV7 – JANUARY 2012
APPLICATION INFORMATION
CCSN1
CCSP1
Figure 36. Application Diagram for 3-Phase CPU, 2-Phase GPU with Inductor DCR Current Sense
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
CCSP3
VIN
CCSN3
1
V5DRV
CPWM3
2
VCC_CORE
V5DRV
+
CPU Phase 3
Figure 37. Application for 3-Phase CPU with Inductor DCR Current Sense
GCSP1
VIN
GCSN1
1
GSKIP
GPWM1
2
VGFX_CORE
V5DRV
+
GPU Phase 1
Figure 38. Application for 1-Phase GPU with Inductor DCR Current Sense
GCSP2
VIN
GCSN2
1
V5DRV
GPWM2
2
VGFX_CORE
V5DRV
+
GPU Phase 2
Figure 39. Application for 2-Phase GPU with Inductor DCR Current Sense
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
21
TPS51650, TPS59650
3R3V
VREF
VREF
VREF
VR_ON
CPGOOD
VCLK
VDIO
ALERT
VR_HOT
GPGOOD
VREF
VREF
GFX_GSNS
CPU_GSNS
GFX_VSNS
CPU_VSNS
GSCN1
CCSN3
GSCP1
CCSP3
VREF
GSKIP
VCLK
VDIO
ALERT
VREF
VREF
VREF
V5
CPWM3
GPWM2
GPWM1
V5
V5DRV
VCCIO
VBAT
V5DRV
VCCIO
VIN
VIN
1
1
2
2
CPU: QC
I_CC_max = 94A
I_TDC = 52A
I_DYN_max = 66A
Min. Over Current Limit = 110A
Loadline = 1.9mohm
Frequency setting = 300kHz
+
GCSP2
CCSP2
GCSN2
CCSN2
CCSP1
CCSN1
CCSN2
CCSP2
VCC_CORE
GFX: GT2
I_cc_max = 46A
I_TDC = 37A
I_DYNAMIC = 38A
Min. Over Current Limit = 52A
Loadline = 3.9mohm
Frequency setting = 388kHz
Note:
VR_HOT, CPGOOD and GPGOOD are open drain outputs.
If used, they would need pull-up resistors.
To CPU SVID
SVID:ALERT
SVID:CLK
SVID:DATA
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
22
www.ti.com
SLUSAV7 – JANUARY 2012
CCSN1
CCSP1
Figure 40. Application for Inductor DCR Current Sense Application Diagram for 2-Phase CPU and GPU
Disabled
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
Table 1. Key External Component Recommendations
FUNCTION
MANUFACTURER
COMPONENT NUMBER
High-side MOSFET
Texas Instruments
CSD17302Q5A
Low-side MOSFET
Texas Instruments
CSD17303Q5
Powerblock MOSFET
Texas Instruments
CSD87350Q5D
Panasonic
ETQP4LR36AFC
NEC-Tokin
MPCH1040LR36,
MPCG1040LR36
TOKO
FDUE1040J-H-R36,
FCUL1040xxR36
ALPS
GLMDR3601A
Panasonic
EEFLXOD471R4
Sanyo
2TPLF470M4E
KEMET
T528Z477M2R5AT
Murata
GRM21BR60J106KE19L
Murata
GRM21BR60J226ME39L
Panasonic
ECJ2FB0J106K
Panasonic
ECJ2FB0J226K
Murata
NCP15WF104F03RC,
NCP18WF104F03RC
Panasonic
ERTJ1VS104F, ERTJ0ES104F
Vishay
WSK0612L7500FEA
Stackpole
CSSK0612FTL750
Inductors
Bulk Output Capacitors
Ceramic Output Capacitors
NTC Thermistors
Sense Resistors
DETAILED DESCRIPTION
Functional Overview
The TPS51650 and TPS59650 are a DCAP+™ mode adaptive on-time controllers.
The output voltage is set using a DAC that outputs a reference in accordance with the 8-bit VID code defined in
Intel IMVP-7 PWM Specification document. In adaptive on-time converters, the controller varies the on-time as a
function of input and output voltage to maintain a nearly constant frequency during steady-state conditions. In
conventional voltage-mode constant on-time converters, each cycle begins when the output voltage crosses to a
fixed reference level. However, in these devices, the cycle begins when the current feedback reaches an error
voltage level which corresponds to the amplified difference between the DAC voltage and the feedback output
voltage. In the case of two-phase or three-phase operation, the current feedback from all the phases is summed
up at the output of the internal current-sense amplifiers.
This approach has two advantages:
• The amplifier DC gain sets an accurate linear load-line; this is required for CPU core applications.
• The error voltage input to the PWM comparator is filtered to improve the noise performance.
In addition, the difference of the DAC-to-output voltage and the current feedback goes through an integrator to
give a more or less linear load-line even at light loads where the inductor current is in discontinuous conduction
mode (DCM).
In a steady-state condition, the phases of the TPS51650 and TPS59650 switch 180° phase-displacement for
two-phase mode and 120° phase-displacement for three-phase mode. The phase displacement is maintained
both by the architecture (which does not allow both high-side gate drives to be on in any condition except
transients) and the current ripple (which forces the pulses to be spaced equally). The controller forces current
sharing adjusting the on-time of each phase. Current balancing requires no user intervention, compensation, or
extra components.
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
23
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
User Selections
After the 5-V and the 3.3-V power are applied to the controller, the controller must be enabled by the VR_ON
signal going high to the VCCIO logic level. At this time, the following information is latched and cannot be
changed anytime during operation. The ELECTRICAL CHARACTERISTICS table defines the values of each of
the selections.
• Operating Frequency. The resistor from CF-IMAX pin to GND sets the frequency of the CPU channel. The
resistor from GF-IMAX to GND sets the frequency of the GPU channel. See the EC Table for the resistor
settings corresponding to each frequency selection. It is to be noted that the operating frequency is a
quasi-fixed frequency in the sense that the ON time is fixed based on the input voltage (at the VBAT pin) and
output voltage (set by VID). The OFF time varies based on various factors such as load and power-stage
components.
• Maximum Current Limit (ICC(max)) Information. The ICC(max) information of the CPU, which can be set by the
voltage on the CF-IMAX pin. The ICC(max) information of the GPU channel, which can be set by the voltage on
the GF-IMAX pin.
• Overcurrent Protection (OCP) Level. The resistor from COCP-R to GND sets the OCP level of the CPU
channel. The resistor from GOCP-R to GND sets the OCP level of the GPU channel.
• Overshoot Reduction (OSR) and Undershoot Reduction (USR) Levels. The voltage on COCP-R pin sets
the OSR and USR level for CPU channel. The voltage on GOCP-R sets the OSR and USR level on GPU
channel. At start-up time, a voltage level (defined in EC Table) detected on GSKIP pin is used to turn OSR
only OFF, or USR only OFF, for both CPU and GPU channels. A voltage level of less than 300 mV makes
both OSR and USR active.
• Slew Rate. The SetVID-Fast slew rate is set by the voltage on the SLEWA pin. The rate is the same for both
the CPU and GPU channels. The SetVID-Slow is ¼ of the SetVID-Fast rate.
• Base SVID Address: The resistor to GND from SLEWA pin sets the base SVID address.
Table 2. Key Selections Summary (1)
SELECTION
RESISTANCE (kΩ)
FREQUENCY
OCP
20
Lowest
Lowest
VOLTAGE
SETTING (V)
(VSLEWA)
SLEW RATE (V)
OSR / USR
0000
0.2
12
Least overshoot,
least undershoot
24
0010
0.4
4
30
0100
0.6
8
39
0110
0.8
12
1000
1.0
16
75
1010
1.2
20
100
1100
1.4
23
1110
1.6
26
Rising
56
150
(1)
Highest
Rising
Highest
BASE
ADDRESS
Rising
Maximum overshoot,
maximum undershoot
See ELECTRICAL CHARACTERISTICS table for complete settings and values.
Table 3. Active Channels and Phases
CPU
(Active Phases)
GPU
(Active Phases)
24
CCSP1
CCSN1
CCSP2
CCSN2
3
CS
CS
CS
CS
2
CS
CS
CS
CS
1
CS
CS
3.3 V
GND
OFF
3.3 V
GND
GND
2
n/a
n/a
1
n/a
n/a
OFF
n/a
n/a
Submit Documentation Feedback
CCSP3
CCSN3
GCSP1
CGSN1
GCSP2
CGSN2
CS
CS
n/a
n/a
n/a
n/a
3.3 V
GND
n/a
n/a
n/a
n/a
GND
GND
n/a
n/a
n/a
n/a
GND
GND
GND
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
CS
CS
CS
CS
n/a
n/a
n/a
n/a
CS
CS
3.3 V
GND
n/a
n/a
n/a
n/a
3.3 V
GND
GND
GND
Copyright © 2012, Texas Instruments Incorporated
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
PWM Operation
Referring to the FUNCTIONAL BLOCK DIAGRAM and Figure 41, in continuous conduction mode, the converter
operates as shown in Figure 41.
VCORE
ISUM
VCOMP
SW_CLK
Phase 1
Phase 2
Phase 3
Time
UDG-11031
Figure 41. D-CAP+ Mode Basic Waveforms
Starting with the condition that the hig-side FETs are off and the low-side FETs are on, the summed current
feedback (ISUM) is higher than the error amplifier output (VCOMP). ISUM falls until it reaches the VCOMP level, which
contains a component of the output ripple voltage. The PWM comparator senses where the two waveform values
cross and triggers the on-time generator. This generates the internal SW_CLK. Each SW_CLK corresponds to
one switching ON pulse for one phase.
During single-phase operation, every SW_CLK generates a switching pulse on the same phase. Also, ISUM
voltage corresponds to just a single-phase inductor current.
During multi-phase operation, the SW_CLK is distributed to each of the phases in a cycle. Using the summed
inductor current and then cyclically distributing the ON-pulses to each phase automatically yields the required
interleaving of 360/N, where N is the number of phases.
Current Sensing
The TPS51650 and TPS59650 provide independent channels of current feedback for every phase. This
increases the system accuracy and reduces the dependence of circuit performance on layout compared to an
externally summed architecture. The current sensing topology can be Inductor DCR Sensing, which yields the
best efficiency, or Resistor Current Sensing, which provides the most accuracy across wide temperature range.
DCR sensing can be optimized by using a NTC thermistor to reduce the variation of current sense with
temperature.
The pins CCSP1, CCSN1, CCSP2, CCSN2 and CCSP3, CCSN3 are used for the three phases of the CPU
channel. The pins GCSP1, GCSN1 and GCSP2 and GCSN2 are for the two-phase GPU channel.
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
25
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
Setting the Load-line (DROOP)
VVID
Slope of Loadline RLL
VDROOP
VDROOP = RLL x ICC
ICC
UDG-11032
Figure 42. Load Line
VDROOP = RLL ´ ICC =
RCS(eff ) ´ A CS ´ ICC
RDROOP ´ GM
where
•
•
•
•
•
26
ACS is the gain of the current sense amplifier
RCS(eff) is the effective current sense resistance, whether a sense resistor or inductor DCR is used
ICC is the load current
RDROOP is the value of resistor from the DROOP pin to VREF
GM is the gain of the droop amplifier
Submit Documentation Feedback
(1)
Copyright © 2012, Texas Instruments Incorporated
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
Load Transients
When there is a sudden load increase, the output voltage immediately drops. This is reflected as a rising voltage
on the COMP pin. This forces the PWM pulses to come in sooner and more frequent which causes the inductor
current to rapidly increase. As the inductor current reaches the new load current, a steady-state operating
condition is reached and the PWM switching resumes the steady-state frequency.
When there is a sudden load release, the output voltage rises. This is reflected as a falling voltage on the COMP
pin. This delays the PWM pulses until the inductor current reaches the new load current level. At that point,
switching resumes and steady-state switching continues.
For simplicity, neither Figure 43, nor Figure 44 show the ripple on the Output VCORE nor the COMP waveform.
LOAD
LOAD
VCORE
VCORE
ISUM
COMP
ISUM
COMP
SW_CLK
SW_CLK
Phase 1
Phase 1
Phase 2
Phase 2
Phase 3
Phase 3
Time
UDG-11034
UDG-11033
Figure 43. Operation During Load Transient
(Insertion)
Figure 44. Operation During Load Transient
(Release)
Overshoot Reduction (OSR)
In low duty-cycle synchronous buck converters, an overshoot condition results from the output inductor having a
too little voltage (VCORE) with which to respond to a transient load release.
In Figure 45, a single phase converter is shown for simplicity. In an ideal converter, with typical input voltage of
12 V and 1.2-V output, the inductor has 10.8 V (12 V – 1.2 V) to respond to a transient load increase, but only
1.2 V with which to respond once the load releases.
12 V
+
–
10.8 V
L
1.2 V
–
1.2 V
+
C
UDG-11035
Figure 45. Synchronous Converter
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
27
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
When the overshoot reduction feature is enabled, the output voltage increases beyond a value that corresponds
to a voltage difference between the ISUM voltage and the COMP voltage, exceeding the specified OSR voltage
specified in the ELECTRICAL CHARACTERISTICS. At that instant, the low-side drivers are turned OFF. When
the low-side driver is turned OFF, the energy in the inductor is partially dissipated by the body diodes. As the
overshoot reduces, the low-side drivers are turned ON again.
Figure 46 shows the overshoot without OSR. Figure 47 shows the overshoot with OSR. The overshoot reduces
by approximately 23 mV. This shows that reduced output capacitance can be used while continuing to meet the
specification. Note the low-side driver turning OFF briefly during the overshoot.
Figure 46. 43-A Load Transient Release Without
OSR Enabled.
Figure 47. 43-A Load Transient Release With OSR
Enabled
Undershoot Reduction (USR)
When the transient load increase becomes quite large, it becomes difficult to meet the energy demanded by the
load especially at lower input voltages. Then it is necessary to quickly increase the energy tin the inductors
during the transient load increase. This is achieved in these devices by enabling pulse overlapping. In order to
maintain the interleaving of the multi-phase configuration and yet be able to have pulse-overlapping during
load-insertion, the undershoot reduction (USR) mode is entered only when necessary. This mode is entered
when the difference between COMP voltage and ISUM voltage exceeds the USR voltage level specified in the
ELECTRICAL CHARACTERISTICS table.
Figure 48 shows the performance with undershoot reduction. Figure 49 shows the performance without
undershoot reduction and that it is possible to eliminate undershoot by enabling the undershoot reduction. This
allows reduced output capacitance to be used and still meet the specification.
When the transient condition is over, the interleaving of the phases is resumed. For Figure 48, note the
overlapping pulses for Phase 1 and Phase 2 with USR enabled.
28
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS51650, TPS59650
www.ti.com
Figure 48. Performance for a 43-A Load Transient
Release Without USR Enabled
Copyright © 2012, Texas Instruments Incorporated
SLUSAV7 – JANUARY 2012
Figure 49. Performance for a 43-A Load Transient
Release With USR Enabled
Submit Documentation Feedback
29
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
AutoBalance™ Current Sharing
The basic mechanism for current sharing is to sense the average phase current, then adjust the pulse width of
each phase to equalize the current in each phase. (See Figure 50.)
The PWM comparator (not shown) starts a pulse when the feedback voltage meets the reference. The VBAT
voltage charges Ct(ON) through Rt(ON). The pulse is terminated when the voltage at Ct(ON) matches the t(ON)
reference, normally the DAC voltage (VDAC).
The circuit operates in the following fashion, using Figure 50 as the block diagram. First assume that the 5-µs
averaged value of I1 = I2 = I3. In this case, the PWM modulator terminates at VDAC, and the normal pulse width
is delivered to the system. If instead, I1 > IAVG, then an offset is subtracted from VDAC, and the pulse width for
Phase 1 is shortened, reducing the current in Phase 1 to compensate. If I1 < IAVG, then a longer pulse is
produced, again compensating on a pulse-by-pulse basis.
VBAT 37
VDAC
CCSP1
CCSN1
4
+
Current
Amplifier
5
K x (I1-IAVG)
5 ms
Filter
RT(on)
+
PWM1
+
CT(on)
IAVG
RT(on)
VDAC
CCSP2
CCSN2
7
+
Current
Amplifier
6
K x (I2-IAVG)
5 ms
Filter
+
PWM2
+
CT(on)
IAVG
Averaging
Circuit
IAVG
RT(on)
VDAC
CCSP3
CCSN3
8
9
+
Current
Amplifier
5 ms
Filter
K x (I3-IAVG)
+
+
IAVG
PWM3
CT(on)
UDG-11036
Figure 50. Schematic Representation of AutoBalance Current Sharing
Dynamic VID and Power-State Changes
In
•
•
•
IMVP-7, there are 3 basic types of VID changes:
SetVID-Fast
SetVID-Slow
SetVID-Decay
SetVID-Fast change and a SetVID-Slow change automatically puts the power state in PS0. A SetVID-Decay
change automatically puts the power state in PS2.
30
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
The CPU operates in the maximum phase mode when it is in PS0. This means when the CPU channel of the
controller is configured as 3-phase, all 3 phases are active in PS0. When configured in 2-phase mode, the two
phases are active in PS0. But in PS1, PS2 and PS3, the operation is in single-phase mode. Additionally, the
CPU channel in PS0 mode operates in forced continuous conduction mode (FCCM). But in PS1, PS2 and PS3,
the CPU channel operates in diode emulation (DE) mode for additional power savings and higher efficiency.
The single-phase GPU section always operates in diode emulation (DE) mode in all PS states.
The slew rate for a SetVID-Fast is the slew rate set at the SLEWA pin. This slew rate is defined in the
ELECTRICAL CHARACTERISTICS table. The SetVID-Slow is ¼ of the SetVID-Fast slew rate. On a
SetVID-Decay the output voltage decays by the rate of the load current or 1/8 of the slew rate whichever is
slower.
Additionally, on a SetVID-Fast change for a VID-up transition, the gain of the gM amplifier is increased to speed
up the response of the output voltage to meet the Intel timing requirement. So, it is possible to observe an
overshoot at the output voltage on a VID-up transition. This overshoot is allowed by the Intel specification.
XXX
Table 4. VID (continued)
Table 4. VID
VID
7
VID
6
VID
5
VID
4
VID
3
VID
2
VID
1
VID
0
HEX
0
0
0
0
0
0
0
0
00
0.000
0
0
0
0
0
0
0
1
01
0.250
0
0
0
0
0
0
1
0
02
0.255
0
0
0
0
0
0
1
1
03
0.260
0
0
0
0
0
1
0
0
04
0.265
0
0
0
0
0
1
0
1
05
0.270
0
0
0
0
0
1
1
0
06
0.275
0
0
0
0
0
1
1
1
07
0.280
0
0
0
0
1
0
0
0
08
0.285
0
0
0
0
1
0
0
1
09
0.290
0
0
0
0
1
0
1
0
0A
0.295
0
0
0
0
1
0
1
1
0B
0.300
0
0
0
0
1
1
0
0
0C
0.305
0
0
0
0
1
1
0
1
0D
0.310
0
0
0
0
1
1
1
0
0E
0.315
0
0
0
0
1
1
1
1
0F
0.320
0
0
0
1
0
0
0
0
10
0.325
0
0
0
1
0
0
0
1
11
0.330
0
0
0
1
0
0
1
0
12
0.335
0
0
0
1
0
0
1
1
13
0.340
0
0
0
1
0
1
0
0
14
0.345
0
0
0
1
0
1
0
1
15
0.350
0
0
0
1
0
1
1
0
16
0.355
0
0
0
1
0
1
1
1
17
0.360
0
0
0
1
1
0
0
0
18
0.365
0
0
0
1
1
0
0
1
19
0.370
0
0
0
1
1
0
1
0
1A
0.375
0
0
0
1
1
0
1
1
1B
0.380
0
0
0
1
1
1
0
0
1C
0.385
0
0
0
1
1
1
0
1
1D
0.390
0
0
0
1
1
1
1
0
1E
0.395
0
0
0
1
1
1
1
1
1F
0.400
Copyright © 2012, Texas Instruments Incorporated
VDAC
0
0
1
0
0
0
0
0
20
0.405
0
0
1
0
0
0
0
1
21
0.410
0
0
1
0
0
0
1
0
22
0.415
0
0
1
0
0
0
1
1
23
0.420
0
0
1
0
0
1
0
0
24
0.425
0
0
1
0
0
1
0
1
25
0.430
0
0
1
0
0
1
1
0
26
0.435
0
0
1
0
0
1
1
1
27
0.440
0
0
1
0
1
0
0
0
28
0.445
0
0
1
0
1
0
0
1
29
0.450
0
0
1
0
1
0
1
0
2A
0.455
0
0
1
0
1
0
1
1
2B
0.460
0
0
1
0
1
1
0
0
2C
0.465
0
0
1
0
1
1
0
1
2D
0.470
0
0
1
0
1
1
1
0
2E
0.475
0
0
1
0
1
1
1
1
2F
0.480
0
0
1
1
0
0
0
0
30
0.485
0
0
1
1
0
0
0
1
31
0.490
0
0
1
1
0
0
1
0
32
0.495
0
0
1
1
0
0
1
1
33
0.500
0
0
1
1
0
1
0
0
34
0.505
0
0
1
1
0
1
0
1
35
0.510
0
0
1
1
0
1
1
0
36
0.515
0
0
1
1
0
1
1
1
37
0.520
0
0
1
1
1
0
0
0
38
0.525
0
0
1
1
1
0
0
1
39
0.530
0
0
1
1
1
0
1
0
3A
0.535
0
0
1
1
1
0
1
1
3B
0.540
0
0
1
1
1
1
0
0
3C
0.545
0
0
1
1
1
1
0
1
3D
0.550
0
0
1
1
1
1
1
0
3E
0.555
0
0
1
1
1
1
1
1
3F
0.560
0
1
0
0
0
0
0
0
40
0.565
0
1
0
0
0
0
0
1
41
0.570
0
1
0
0
0
0
1
0
42
0.575
Submit Documentation Feedback
31
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
Table 4. VID (continued)
32
Table 4. VID (continued)
0
1
0
0
0
0
1
1
43
0.580
0
1
1
1
0
0
1
1
73
0.820
0
1
0
0
0
1
0
0
44
0.585
0
1
1
1
0
1
0
0
74
0.825
0
1
0
0
0
1
0
1
45
0.590
0
1
1
1
0
1
0
1
75
0.830
0
1
0
0
0
1
1
0
46
0.595
0
1
1
1
0
1
1
0
76
0.835
0
1
0
0
0
1
1
1
47
0.600
0
1
1
1
0
1
1
1
77
0.840
0
1
0
0
1
0
0
0
48
0.605
0
1
1
1
1
0
0
0
78
0.845
0
1
0
0
1
0
0
1
49
0.610
0
1
1
1
1
0
0
1
79
0.850
0
1
0
0
1
0
1
0
4A
0.615
0
1
1
1
1
0
1
0
7A
0.855
0
1
0
0
1
0
1
1
4B
0.620
0
1
1
1
1
0
1
1
7B
0.860
0
1
0
0
1
1
0
0
4C
0.625
0
1
1
1
1
1
0
0
7C
0.865
0
1
0
0
1
1
0
1
4D
0.630
0
1
1
1
1
1
0
1
7D
0.870
0
1
0
0
1
1
1
0
4E
0.635
0
1
1
1
1
1
1
0
7E
0.875
0
1
0
0
1
1
1
1
4F
0.640
0
1
1
1
1
1
1
1
7F
0.880
0
1
0
1
0
0
0
0
50
0.645
1
0
0
0
0
0
0
0
80
0.885
0
1
0
1
0
0
0
1
51
0.650
1
0
0
0
0
0
0
1
81
0.890
0
1
0
1
0
0
1
0
52
0.655
1
0
0
0
0
0
1
0
82
0.895
0
1
0
1
0
0
1
1
53
0.660
1
0
0
0
0
0
1
1
83
0.900
0
1
0
1
0
1
0
0
54
0.665
1
0
0
0
0
1
0
0
84
0.905
0
1
0
1
0
1
0
1
55
0.670
1
0
0
0
0
1
0
1
85
0.910
0
1
0
1
0
1
1
0
56
0.675
1
0
0
0
0
1
1
0
86
0.915
0
1
0
1
0
1
1
1
57
0.680
1
0
0
0
0
1
1
1
87
0.920
0
1
0
1
1
0
0
0
58
0.685
1
0
0
0
1
0
0
0
88
0.925
0
1
0
1
1
0
0
1
59
0.690
1
0
0
0
1
0
0
1
89
0.930
0
1
0
1
1
0
1
0
5A
0.695
1
0
0
0
1
0
1
0
8A
0.935
0
1
0
1
1
0
1
1
5B
0.700
1
0
0
0
1
0
1
1
8B
0.940
0
1
0
1
1
1
0
0
5C
0.705
1
0
0
0
1
1
0
0
8C
0.945
0
1
0
1
1
1
0
1
5D
0.710
1
0
0
0
1
1
0
1
8D
0.950
0
1
0
1
1
1
1
0
5E
0.715
1
0
0
0
1
1
1
0
8E
0.955
0
1
0
1
1
1
1
1
5F
0.720
1
0
0
0
1
1
1
1
8F
0.960
0
1
1
0
0
0
0
0
60
0.725
1
0
0
1
0
0
0
0
90
0.965
0
1
1
0
0
0
0
1
61
0.730
1
0
0
1
0
0
0
1
91
0.970
0
1
1
0
0
0
1
0
62
0.735
1
0
0
1
0
0
1
0
92
0.975
0
1
1
0
0
0
1
1
63
0.740
1
0
0
1
0
0
1
1
93
0.980
0
1
1
0
0
1
0
0
64
0.745
1
0
0
1
0
1
0
0
94
0.985
0
1
1
0
0
1
0
1
65
0.750
1
0
0
1
0
1
0
1
95
0.990
0
1
1
0
0
1
1
0
66
0.755
1
0
0
1
0
1
1
0
96
0.995
0
1
1
0
0
1
1
1
67
0.760
1
0
0
1
0
1
1
1
97
1.000
0
1
1
0
1
0
0
0
68
0.765
1
0
0
1
1
0
0
0
98
1.005
0
1
1
0
1
0
0
1
69
0.770
1
0
0
1
1
0
0
1
99
1.010
0
1
1
0
1
0
1
0
6A
0.775
1
0
0
1
1
0
1
0
9A
1.015
0
1
1
0
1
0
1
1
6B
0.780
1
0
0
1
1
0
1
1
9B
1.020
0
1
1
0
1
1
0
0
6C
0.785
1
0
0
1
1
1
0
0
9C
1.025
0
1
1
0
1
1
0
1
6D
0.790
1
0
0
1
1
1
0
1
9D
1.030
0
1
1
0
1
1
1
0
6E
0.795
1
0
0
1
1
1
1
0
9E
1.035
0
1
1
0
1
1
1
1
6F
0.800
1
0
0
1
1
1
1
1
9F
1.040
0
1
1
1
0
0
0
0
70
0.805
1
0
1
0
0
0
0
0
A0
1.045
0
1
1
1
0
0
0
1
71
0.810
1
0
1
0
0
0
0
1
A1
1.050
0
1
1
1
0
0
1
0
72
0.815
1
0
1
0
0
0
1
0
A2
1.055
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
Table 4. VID (continued)
Table 4. VID (continued)
1
0
1
0
0
0
1
1
A3
1.060
1
1
0
1
0
0
1
1
D3
1.300
1
0
1
0
0
1
0
0
A4
1.065
1
1
0
1
0
1
0
0
D4
1.305
1
0
1
0
0
1
0
1
A5
1.070
1
1
0
1
0
1
0
1
D5
1.310
1
0
1
0
0
1
1
0
A6
1.075
1
1
0
1
0
1
1
0
D6
1.315
1
0
1
0
0
1
1
1
A7
1.080
1
1
0
1
0
1
1
1
D7
1.320
1
0
1
0
1
0
0
0
A8
1.085
1
1
0
1
1
0
0
0
D8
1.325
1
0
1
0
1
0
0
1
A9
1.090
1
1
0
1
1
0
0
1
D9
1.330
1
0
1
0
1
0
1
0
AA
1.095
1
1
0
1
1
0
1
0
DA
1.335
1
0
1
0
1
0
1
1
AB
1.100
1
1
0
1
1
0
1
1
DB
1.340
1
0
1
0
1
1
0
0
AC
1.105
1
1
0
1
1
1
0
0
DC
1.345
1
0
1
0
1
1
0
1
AD
1.110
1
1
0
1
1
1
0
1
DD
1.350
1
0
1
0
1
1
1
0
AE
1.115
1
1
0
1
1
1
1
0
DE
1.355
1
0
1
0
1
1
1
1
AF
1.120
1
1
0
1
1
1
1
1
DF
1.360
1
0
1
1
0
0
0
0
B0
1.125
1
1
1
0
0
0
0
0
E0
1.365
1
0
1
1
0
0
0
1
B1
1.130
1
1
1
0
0
0
0
1
E1
1.370
1
0
1
1
0
0
1
0
B2
1.135
1
1
1
0
0
0
1
0
E2
1.375
1
0
1
1
0
0
1
1
B3
1.140
1
1
1
0
0
0
1
1
E3
1.380
1
0
1
1
0
1
0
0
B4
1.145
1
1
1
0
0
1
0
0
E4
1.385
1
0
1
1
0
1
0
1
B5
1.150
1
1
1
0
0
1
0
1
E5
1.390
1
0
1
1
0
1
1
0
B6
1.155
1
1
1
0
0
1
1
0
E6
1.395
1
0
1
1
0
1
1
1
B7
1.160
1
1
1
0
0
1
1
1
E7
1.400
1
0
1
1
1
0
0
0
B8
1.165
1
1
1
0
1
0
0
0
E8
1.405
1
0
1
1
1
0
0
1
B9
1.170
1
1
1
0
1
0
0
1
E9
1.410
1
0
1
1
1
0
1
0
BA
1.175
1
1
1
0
1
0
1
0
EA
1.415
1
0
1
1
1
0
1
1
BB
1.180
1
1
1
0
1
0
1
1
EB
1.420
1
0
1
1
1
1
0
0
BC
1.185
1
1
1
0
1
1
0
0
EC
1.425
1
0
1
1
1
1
0
1
BD
1.190
1
1
1
0
1
1
0
1
ED
1.430
1
0
1
1
1
1
1
0
BE
1.195
1
1
1
0
1
1
1
0
EE
1.435
1
0
1
1
1
1
1
1
BF
1.200
1
1
1
0
1
1
1
1
EF
1.440
1
0
0
0
0
0
0
C0
1.205
1
1
1
1
0
0
0
0
F0
1.445
1
1
0
0
0
0
0
1
C1
1.210
1
1
1
1
0
0
0
1
F1
1.450
1
1
0
0
0
0
1
0
C2
1.215
1
1
1
1
0
0
1
0
F2
1.455
1
1
0
0
0
0
1
1
C3
1.220
1
1
1
1
0
0
1
1
F3
1.460
1
1
0
0
0
1
0
0
C4
1.225
1
1
1
1
0
1
0
0
F4
1.465
1
1
0
0
0
1
0
1
C5
1.230
1
1
1
1
0
1
0
1
F5
1.470
1
1
0
0
0
1
1
0
C6
1.235
1
1
1
1
0
1
1
0
F6
1.475
1
1
0
0
0
1
1
1
C7
1.240
1
1
1
1
0
1
1
1
F7
1.480
1
1
0
0
1
0
0
0
C8
1.245
1
1
1
1
1
0
0
0
F8
1.485
1
1
0
0
1
0
0
1
C9
1.250
1
1
1
1
1
0
0
1
F9
1.490
1
1
0
0
1
0
1
0
CA
1.255
1
1
1
1
1
0
1
0
FA
1.495
1
1
0
0
1
0
1
1
CB
1.260
1
1
1
1
1
0
1
1
FB
1.500
1
1
0
0
1
1
0
0
CC
1.265
1
1
1
1
1
1
0
0
FC
1.505
1
1
0
0
1
1
0
1
CD
1.270
1
1
1
1
1
1
0
1
FD
1.510
1
1
0
0
1
1
1
0
CE
1.275
1
1
1
1
1
1
1
0
FE
1.515
1
1
0
0
1
1
1
1
CF
1.280
1
1
1
1
1
1
1
1
FF
1.520
1
1
0
1
0
0
0
0
D0
1.285
1
1
0
1
0
0
0
1
D1
1.290
1
1
0
1
0
0
1
0
D2
1.295
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
33
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
Gate Driver
The TPS51650 and TPS59650 incorporate two internal strong, high-performance gate drives with adaptive
cross-conduction protection. These drivers are for two phases in the CPU channel. The third phase of the CPU
and the single-phase GPU channel require external drivers.
The internal driver in these devices uses the state of the CDLx and CSWx pins to be sure the high-side or
low-side FET is OFF before turning the other ON. Fast logic and high drive currents (up to 8-A typical) quickly
charge and discharge FET gates to minimize dead-time to increase efficiency. The high-side gate driver also
includes an integrated boost FET instead of merely a diode to increase the effective drive voltage for higher
efficiency. An adaptive zero-crossing technique, which detects the switch-node voltage before turning OFF the
low-side FET, is used to minimize losses during DCM operation.
Input Under Voltage Protection (5V and 3.3V)
The TPS51650 and TPS59650 continuously monitor the voltage on the V5DRV, V5 and V3R3 pin to be sure the
value is high enough to bias the device properly and provide sufficient gate drive potential to maintain high
efficiency. The converter starts with approximately 4.4-V and has a nominal 200 mV of hysteresis. The input
(VBAT) does not have a UVLO function, so the circuit operates with power inputs as low as approximately 3 x
VCORE.
Power Good (CPGOOD and GPGOOD)
These devices have two open-drain power good pins that follow the requirements for IMVP-7. CPGOOD is used
for the CPU channel output voltage and GPGOOD is used for the GPU channel output voltage. Both of these
signals are active high. The upper and the lower limits for the output voltage for xPGOOD active are:
• Upper: VDAC +220 mV
• Lower : VDAC -315 mV
xPGOOD goes inactive (low) as soon as the VR_ON pin is pulled low or an undervoltage condition on V5 or
V3R3 is detected. The xPGOOD signals are masked during DAC transitions to prevent false triggering during
voltage slewing.
Output Undervoltage Protection
Output undervoltage protection works in conjunction with the current protection described below. If VCORE drops
below the low PGOOD threshold, then the drivers are turned OFF until VR_ON is cycled.
Overcurrent Protection
The TPS51650 and TPS59650 use a valley current limiting scheme, so the ripple current must be considered.
The DC current value at OCP is the OCP limit value plus half of the ripple current. Current limiting occurs on a
phase-by-phase and pulse-by-pulse basis. If the voltage between xCSPx and xCSNx is above the OCP value,
the converter delays the next ON pulse until it drops below the OCP limit. For inductor current sensing circuits,
the voltage between xCSPx and xCSNx is the inductor DCR value multiplied by the resistor divider which is part
of the NTC compensation network. As a result, a wide range of OCP values can be obtained by changing the
resistor divider value. In general, use the highest OCP setting possible with the least attenuation in the resistor
divider to provide as much signal to the device as possible. This provides the best performance for all
parameters related to current feedback.
In OCP mode, the voltage drops until the UVP limit is reached. Then, the converter sets the xPGOOD to inactive,
and the drivers are turned OFF. The converter remains in this state until the device is reset by the VR_ON.
Overvoltage Protection
An OVP condition is detected when VCORE is more than 220 mV greater than VDAC. In this case, the converter
sets xPGOOD inactive, and turns ON the drive for the Low-side FET. The converter remains in this state until the
device is reset by cycling VR_ON. However, because of the dynamic nature of IMVP-7 systems, the +220 mV
OVP threshold is blanked much of the time. In order to provide protection to the processor 100% of the time,
there is a second OVP level fixed at 1.7 V which is always active. If the fixed OVP condition is detected, the
PGOOD are forced inactive and the low-side FETs are tuned ON. The converter remains in this state until
VR_ON is cycled.
34
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
Over Temperature Protection
Two types of thermal protection are provided in these devices:
• VR_HOT
• Thermal Shutdown
VR_HOT
The VR_HOT signal is an Intel-defined open-drain signal that is used to protect the VCORE power chain. To use
VR_HOT, place an NTC thermistor at the hottest area of the CPU channel and connect it from CTHERM pin to
GND. Similarly for GPU channel, place the NTC thermistor at the hottest area and connect it from GTHERM to
GND. Also, connect a resistor from VREF to GTHERM and CTHERM. As the temperature increases, the
xTHERM voltage drops below the THERM threshold, VR_HOT is activated. A small capacitor may be connected
to the xTHERM pins for high frequency noise filtering.
lists the thermal zone register bits based on the xTHERM pin voltage.
Table 5. Thermal Zone Register Bits
OUTPUT IS
SHUTDOWN
VR_HOT
ASSERTED
b7
b6
b5
b4
b3
b2
b1
b0
410 mV
455 mV
458 mV
523 mV
559 mV
598 mV
638 mV
680 mV
783 mV
SVID ALERT ASSERTED
xTHERM THRESHOLD VOLTAGE FOR THE TEMPERATURE
ZONE REGISTER BITS TO BE ASSERTED.
Thermal Shutdown
When the xTHERM pin voltage continues to drop even after VR_HOT is asserted, the drivers turn OFF and the
output is shutdown. These devices also have an internal temperature sensor. When the temperature reaches a
nominal 155°C, the device shuts down until the temperature cools approximately 20°C. Then, the circuit can be
re-started by cycling VR_ON.
Setting the Maximum Processor Current (ICC(max))
The TPS51640 controller allows the user to set the maximum processor current with the multi-function pins
CF-IMAX and GF-IMAX. The voltage on the CF-IMAX and GF-IMAX at start-up sets the maximum processor
current (ICC(max)) for CPU and GPU respectively.
The RCF and RGF are resistors to GND from CF-IMAX and GF-IMAX respectively to select the frequency setting.
RCIMAX is the resistor from VREF to CF-IMAX and RGIMAX is the resistor from VREF to GF-IMAX.
Equation 2 describes the setting the ICC(max) for the CPU channel and Equation 3 describes the setting the
ICC(max) for the GPU channel.
æ
ö
RCF
ICC(max )CPU = 255 ´ ç
÷
R
R
+
CIMAX ø
è CF
(2)
æ
ö
RGF
ICC(max )GPU = 255 ´ ç
÷
è RGF + RGIMAX ø
(3)
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
35
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
DESIGN STEPS
The design procedure using the TPS51650, TPS59650, and TPS59641 is very simple . An excel-based
component value calculation tool is available. Contact your local TI representative to get a copy of the
spreadsheet.
The procedure is explained here below with the following design example:
Table 6. Design Example Specifications
CPU VCORE SPECIFICATIONS
GFX VCORE SPECIFICATIONS
Phases
3
2
Input voltage range
9 V to 20 V
9 V to 20 V
VHFM
0.9 V
1.23 V
ICC(max)
94 A
46 A
IDYN(max)
66 A
38 A
ICC(tdc)
52
37.5
Load-line
1.9 mV/A
3.9 mV/A
Fast slew rate (minimum)
10 mV/µs
10 mV/µs
Step One: Select switching frequency.
The CPU channel switching frequency is selected by a resistor from CF-IMAX to GND (RCF) and GPU channel
switching frequency is selected by a resistor from GF-IMAX to GND (RGF). The frequency is an approximate
frequency and is expected to vary based on load and input voltage.
Table 7. Switching Frequency Selection
SELECTION
RESISTANCE (kΩ)
CPU CHANNEL
FREQUENCY (kHz)
GPU CHANNEL
FREQUENCY (kHz)
20
250
275
24
300
330
30
350
385
39
400
440
56
450
495
75
500
550
100
550
605
150
600
660
This desig defines the switching frequency for the CPU channel as 300 kHz and defines the GPU channel as 385
kHz. Therefore,
• RCF = 21 kΩ
• RGF = 24 kΩ
Step Two: Set ICC(max)
The ICC(max) is set by the voltage on CF-IMAX for CPU channel and GF-IMAX for GPU channel. This is set by the
resistors from VREF to CF-IMAX (RCMAX) and from VREF to GF-IMAX (RGMAX)
From Equation 2 and Equation 3,
• RCMAX = 42.2 kΩ
• RGMAX = 110 kΩ
Step Three: Set the slew rate.
The slew rate is set by the voltage setting on SLEWA pin. For a minimum slew rate of 10 mV/ms, the voltage on
the SLEWA pin must be less than 0.3 V. Because the SLEWA pin also sets the base address (for the
TPS59650), the simple way to meet this is by having a 20-kΩ resistor from SLEWA to GND.
36
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
Step Four: Determine inductor value and choose inductor.
Smaller values of inductor have better transient performance but higher ripple and lower efficiency. Higher values
have the opposite characteristics. It is common practice to limit the ripple current to 20% to 40% of the maximum
current per phase. This example uses a ripple current of 30%.
94 A
IP-P =
´ 0.3 = 9.4 A
3
(4)
V ´ dT
L=
IP-P
where
•
•
•
V = VIN-MAX – VHFM = 19.1 V
dT = VHFM / (f × VIN-MAX) = 150 ns
IP-P = 9.4 A
(5)
Using those calculations, L = 0.304 µH.
An inductance value of 0.36 µH is chosen as this is a commonly used inductor for VCORE application. The
inductor must not saturate during peak loading conditions.
æ ICC(max ) I
ö
ISAT = ç
+ P-P ÷ ´ 1.2 = 43.2 A
ç NPHASE
2 ÷
è
ø
(6)
The factor of 1.2 allows for current sensing and current limiting tolerances; the factor of 1.25 is the Intel 25%
momentary OCP requirement.
The chosen inductor should have the following characteristics:
• An inductance to current curve ratio equal to 1 (or as close possible). Inductor DCR sensing is based on the
idea L/DCR is approximately a constant through the current range of interest.
• Either high saturation or soft saturation.
• Low DCR for improved efficiency, but at least 0.7 mΩ for proper signal levels.
• DCR tolerance as low as possible for load-line accuracy.
For this application, a 0.36-µH, 0.825-mΩ inductor is chosen. Because the per phase current for GPU is same as
CPU, the same inductor for GPU channel is chosen.
Step Five: Determine current sensing method.
The TPS51650 and TPS59650 support both resistor sensing and inductor DCR sensing. Inductor DCR sensing
is chosen. For resistor sensing, substitute the resistor value (0.75 mΩ recommended for a 3-phase 94-A
application) for RCS in the subsequent equations and skip Step Four.
Step Six: Design the thermal compensation network and selection of OCP .
In most designs, NTC thermistors are used to compensate thermal variations in the resistance of the inductor
winding. This winding is generally copper, and so has a resistance coefficient of 3900 PPM/°C. NTC thermistors,
on the other hand, have very non-linear characteristics and need two or three resistors to linearize them over the
range of interest. The typical DCR circuit is shown in Figure 51.
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
37
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
L
RSEQU
RDCR
RNTC
I
RSERIES
RPAR
CSENSE
CSP
CSN
UDG-11039
Figure 51. Typical DCR Sensing Circuit
In this circuit, the voltage across the CSENSE capacitor exactly equals the voltage across the RDCR resistor when
Equation 7 is true.
L
= CSENSE ´ REQ
RDCR
where
•
REQ =
REQ is the series/parallel combination of RSEQU, RNTC, RSERIES and RPAR
(7)
RP _ N
RSEQU + RP _ N
RP _ N =
(8)
RPAR ´ (RNTC + RSERIES )
RPAR + RNTC + RSERIES
(9)
CSENSE capacitor type should be stable over temperature. Use X7R or better dielectric (C0G preferred).
Because calculating these values by hand is difficult, TI has a spreadsheet using the Excel Solver function
available to calculate them. Contact a local TI representative to get a copy of the spreadsheet.
In
•
•
•
•
•
this design, the following values are input into the CPU section of the spreadsheet
L = 0.36 µH
RDCR = 0.825 mΩ
Load Line, RIMVP = -1.9 mΩ
Minimum overcurrent limit = 112 A
Thermistor R25 = 100 kΩ and "B" value = 4250 kΩ
In
•
•
•
•
•
this design, the following values are input into the GPU section of the spreadsheet
L = 0.36 µH
RDCR = 0.825 mΩ
Load Line, RIMVP = -3.9 mΩ
Minimum overcurrent limit = 59 A
Thermistor R25 = 100 kΩ and "B" value = 4250 kΩ
The spreadsheet then calculates the OCP (overcurrent protection) setting and the values of RSEQU, RSERIES,
RPAR, and CSENSE. In this case, the OCP setting is the resistor value selection of 56 kΩ from COCP-I to GND and
GOCP-I to GND. The nearest standard component values are:
38
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
•
•
•
•
RSEQU = 17.8 kΩ;
RSERIES = 28.7 kΩ;
RPAR = 162 kΩ
CSENSE =33 nF
Note the effective divider ratio for the inductor DCR. The effective current sense resistance (RCS(eff)) is shown in
Equation 10.
RP _ N
RCS(eff ) = RDCR ´
RSEQU + RP _ N
where
•
RP_N is the series/parallel combination of RNTC, RSERIES and RPAR.
RGDROOP =
RCS(eff ) ´ A CS
RLL ´ GM
=
(10)
0.66mW ´ 12
= 4.12kW
3.9mW ´ 0.497mS
(11)
RCS(eff) is 0.66 mΩ.
Step Seven: Set the load-line.
The load-line for CPU channel is set by the resistor, RCDROOP from CCOMP to VREF. The load-line for GPU
channel is set by the resistor, RGDROOP from the GCOMP pin to VREF. Using the Equation 1, the droop setting
resistors are calculated in Equation 12 and Equation 13.
RCS(eff ) ´ A CS
0.66mW ´ 12
=
= 8.45kW
RCDROOP =
RLL ´ GM
1.9mW ´ 0.497mS
(12)
RGDROOP =
RCS(eff ) ´ A CS
RLL ´ GM
=
0.66mW ´ 12
= 4.12kW
3.9mW ´ 0.497mS
(13)
Step Eight: Programming the CTHERM and GTHERM pins.
The CTHERM and GTHERM pins should be set so that the resistor divider voltage would be greater than 458
mV at normal operation. For VR_HOT to be asserted, the xTHERM pin voltage should fall below 458 mV. The
NTC resistor from xTHERM to GND is chosen as 100 kΩ with a B of 4250K. With this, for a VR_HOT assertion
temperature of 105°C, the resistor from xTHERM to VREF can be calculated as 15.4 kΩ.
Step Nine:Determine the output capacitor configuration.
For the output capacitor, the Intel Power Delivery Guidelines gives the output capacitor recommendations. Using
these devices, it is possible to meet the load transient with lower capacitance by using the OSR and USR
feature. Eight settings are available and this selection must to be tuned based on transient measurement.
Table 8. OSR/USR Selection Settings
INDUCTOR DCR
3-PHASE QC SETTING (V)
2-PHASE SV SETTING (V)
0.8 mW to 0.9 mW
1.0
0.8
1.0 mW to 1.1 mW
1.2
1.0
The resistor from COCP-R to VREF and GOCP-R to VREF can be calculated based on the above voltage setting
and the COCP-R to GND and GOCP-R to GND resistor selected in Step Six. The resistor values are calculated
as 39.2 kΩ for COCP-R to VREF and 2.4 kΩ for GOCP-R to VREF.
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
39
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
PCB LAYOUT GUIDELINE
SCHEMATIC REVIEW
Because the voltage and current feedback signals are fully differential it is a good idea to double check their
polarity.
• CCSP1/CCSN1
• CCSP2/CCSN2
• CCSP2/CCSN2
• GCSP1/GCSN1
• GCSP2/GCSN2
• VCCSENSE to CVFB/VSSSENSE to CGFB (for CPU)
• VCCGTSENSE to GVFB/VSSGTSENSE to GGFB (for GPU)
Also, note the order of the current sense inputs on Pin 4 to Pin 9 as the second phase has a reverse order.
CAUTION
Separate noisy driver interface lines from sensitive analog interface lines: (This is the
MOST CRITICAL LAYOUT RULE)
The TPS51650 and TPS59650 make this as easy as possible. The pin-out arrangement for TPS51650 is shown
in Figure 52. The driver outputs clearly separated from the sensitive analog and digital circuitry. The driver has a
separate PGND and this should be directly connected to the decoupling capacitor that connects from V5DRV to
PGND. The thermal pad of the package is the analog ground for these devices and should NOT be connected
directly to PGND (Pin 42).
Figure 52. Packaging Layout Arranged by Function
40
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
Given the physical layout of most systems, the current feedback (xCSPx, xCSNx) may have to pass near the
power chain. Clean current feedback is required for good load-line, current sharing, and current limiting
performance of these devices, so please take the following precautions:
• Make a Kelvin connection to the pads of the resistor or inductor used for current sensing. See Figure 53 for a
layout example.
• Run the current feedback signals as a differential pair to the device.
• Run the lines in a quiet layer. Isolate them from noisy signals by a voltage or ground plane.
• Put the compensation capacitor for DCR sensing (CSENSE) as close to the CS pins as possible.
• Place any noise filtering capacitors directly underneath these devices and connect to the CS pins with the
shortest trace length possible.
Noisy
Quiet
Inductor
Outline
LLx
VCORE
CSNx
CSPx
RSEQ
Thermistor
RSERIES
UDG-11038
Figure 53. Make Kelvin Connections to the Inductor for DCR Sensing
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
41
TPS51650, TPS59650
SLUSAV7 – JANUARY 2012
www.ti.com
Minimize High-Current Loops
Figure 54 shows the primary current loops in each phase, numbered in order of importance.
The most important loop to minimize the area of is Loop 1, the path from the input capacitor through the high and
low side FETs, and back to the capacitor through ground.
Loop 2 is from the inductor through the output capacitor, ground and Q2. The layout of the low side gate drive
(Loops 3a and 3b) is important. The guidelines for gate drive layout are:
• Make the low-side gate drive as short as possible (1 inch or less preferred).
• Make the DRVL width to length ratio of 1:10, wider (1:5) if possible.
• If changing layers is necessary, use at least two vias.
VBAT
CB
CIN
1
Q1
4b
DRVH
L
4a
VCORE
LL
2
CD
3b
Q2
COUT
DRVL
3a
PGND
UDG-11040
Figure 54. Major Current Loops to Minimize
Power Chain Symmetry
The TPS51650 and TPS59650 do not require special care in the layout of the power chain components. This is
because independent isolated current feedback is provided. If it is possible to lay out the phases in a symmetrical
manner, then please do so. The current feedback from each phase must be clean of noise and have the same
effective current sense resistance.
Place analog components as close to the device as possible.
Place components close to the device in the following order.
1. CS pin noise filtering components
2. xCOMP pin compensation components
3. Decoupling capacitors for VREF, V3R3, V5
4. xTHERM filter capacitor
5. xOCP-R resistors
6. xF-IMAX resistors
42
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS51650, TPS59650
www.ti.com
SLUSAV7 – JANUARY 2012
Grounding Recommendations
These devices have separate analog and power grounds, and a thermal pad. The normal procedure for
connecting these is:
• The thermal pad is the analog ground.
• DO NOT connect the thermal pad to Pin 42 directly as Pin 42 is the PGND which is the Gate driver
Ground.
• Pin 42 (PGND) must be connected directly to the gate driver decoupling capacitor ground terminal.
• Tie the thermal pad (analog ground pin) to a ground island with at least 4 small vias or one large via.
• All the analog components can connect to this analog ground island.
• The analog ground can be connected to any quiet spot on the system ground. A quiet area is defined as a
area where no power supply switching currents are likely to flow. This applies to both the VCORE regulator and
other regulators. Use a single point connection from analog ground to the system ground
• Make sure the low-side FET source connection and the decoupling capacitors have plenty of vias.
Decoupling Recommendations
•
•
•
Decouple V5IN to PGND with at least a 2.2 µF ceramic capacitor.
Decouple V5 and V3R3 with 1 µF to AGND with leads as short as possible,
VREF to AGND with 0.33 µF, with short leads also
Conductor Widths
•
•
•
•
Follow Intel guidelines with respect to the voltage feedback and logic interface connection requirements.
Maximize the widths of power, ground and drive signal connections.
For conductors in the power path, be sure there is adequate trace width for the amount of current flowing
through the traces.
Make sure there are sufficient vias for connections between layers. A good guideline is to use a minimum of 1
via per ampere of current.
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
43
PACKAGE OPTION ADDENDUM
www.ti.com
10-Mar-2012
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
(3)
TPS51650RSLR
ACTIVE
VQFN
RSL
48
2500
Green (RoHS
& no Sb/Br)
CU NIPDAUAGLevel-3-260C-168 HR
TPS51650RSLT
ACTIVE
VQFN
RSL
48
250
Green (RoHS
& no Sb/Br)
CU NIPDAUAGLevel-3-260C-168 HR
TPS59650RSLR
ACTIVE
VQFN
RSL
48
2500
Green (RoHS
& no Sb/Br)
CU NIPDAUAGLevel-3-260C-168 HR
TPS59650RSLT
ACTIVE
VQFN
RSL
48
250
Green (RoHS
& no Sb/Br)
CU NIPDAUAGLevel-3-260C-168 HR
Samples
(Requires Login)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Mar-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
TPS51650RSLR
VQFN
RSL
48
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
2500
330.0
16.4
6.3
6.3
1.5
12.0
16.0
Q2
TPS51650RSLT
VQFN
RSL
48
250
180.0
16.4
6.3
6.3
1.5
12.0
16.0
Q2
TPS59650RSLR
VQFN
RSL
48
2500
330.0
16.4
6.3
6.3
1.5
12.0
16.0
Q2
TPS59650RSLT
VQFN
RSL
48
250
180.0
16.4
6.3
6.3
1.5
12.0
16.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Mar-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TPS51650RSLR
VQFN
RSL
48
2500
346.0
346.0
33.0
TPS51650RSLT
VQFN
RSL
48
250
210.0
185.0
35.0
TPS59650RSLR
VQFN
RSL
48
2500
346.0
346.0
33.0
TPS59650RSLT
VQFN
RSL
48
250
210.0
185.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
Wireless Connectivity
www.ti.com/wirelessconnectivity
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated