CEL UPC2710TB

BIPOLAR ANALOG INTEGRATED CIRCUIT
UPC3223TB
5 V, SILICON MMIC
MEDIUM OUTPUT POWER AMPLIFIER
DESCRIPTION
The PC3223TB is a silicon monolithic IC designed as IF amplifier for DBS tuners. This IC is manufactured using
our 30 GHz fmax UHS0 (Ultra High Speed Process) silicon bipolar process.
FEATURES
• Wideband response : fu = 3.2 GHz TYP. @ 3 dB bandwidth
• Medium output power : PO (sat) = +12.0 dBm @ f = 1.0 GHz
: PO (sat) = +9.0 dBm @ f = 2.2 GHz
• High linearity
: PO (1 dB) = +6.5 dBm @ f = 1.0 GHz
: PO (1 dB) = +5.0 dBm @ f = 2.2 GHz
• Power gain
: GP = 23.0 dB TYP. @ f = 1.0 GHz
• Supply voltage
: VCC = 4.5 to 5.5 V
• Port impedance
: input/output 50
: GP = 23.0 dB TYP. @ f = 2.2 GHz
APPLICATION
• IF amplifiers in DBS converters etc.
ORDERING INFORMATION (Solder Contains Lead)
Part Number
PC3223TB-E3
Package
6-pin super minimold
Marking
C3J
Supplying Form
Embossed tape 8 mm wide
1, 2, 3 pins face the perforation side of tape
Qty 3 kpcs/reel
ORDERING INFORMATION (Pb-Free)
Part Number
PC3223TB-E3-A
Package
6-pin super minimold
Marking
C3J
Supplying Form
Embossed tape 8 mm wide
1, 2, 3 pins face the perforation side of tape
Qty 3 kpcs/reel
Remark To order evaluation samples, contact your nearby sales office.
Part number for sample order: PC3223TB
Caution Observe precautions when handling because these devices are sensitive to electrostatic discharge.
Document No. PU10491EJ01V0DS (1st edition)
Date Published May 2004 CP(K)
UPC3223TB
PIN CONNECTIONS
(Top View)
(Bottom View)
Pin No.
Pin Name
1
INPUT
3
4
4
3
2
GND
2
5
5
2
3
GND
1
6
6
1
4
OUTPUT
5
GND
6
VCC
PRODUCT LINE-UP OF 5 V-BIAS SILICON MMIC MEDIUM OUTPUT AMPLIFIER
(TA = +25 C, f = 1 GHz, VCC = Vout = 5.0 V, ZS = ZL = 50 )
fu
PO(sat)
GP
NF
ICC
(GHz)
(dBm)
(dB)
(dB)
(mA)
PC2708TB
2.9
+10.0
15
6.5
26
PC2709TB
2.3
+11.5
23
5.0
25
C1E
PC2710TB
1.0
+13.5
33
3.5
22
C1F
PC2776TB
2.7
+8.5
23
6.0
25
C2L
PC3223TB
3.2
+12.0
23
4.5
19
C3J
Part No.
Package
6-pin super minimold
Remark Typical performance. Please refer to ELECTRICAL CHARACTERISTICS in detail.
2
Data Sheet PU10491EJ01V0DS
Marking
C1D
UPC3223TB
PIN EXPLANATIONS
PIN
No.
1
Pin Name
INPUT
Voltage (V)
Applied
Pin Voltage
Note
(V)
–
0.96
Function and Applications
Signal input pin.
A internal matching circuit, configured with resistors, enables 50
connection over a wide band.
A multi-feedback circuits is designed to cancel the deviations of hFE and
resistance.
This pin must be coupled to signal source with capacitor for DC cut.
4
OUTPUT
Voltage as
–
Signal output pin.
The inductor must be attached between VCC and output pins to supply
same as VCC
current to the internal output transistors.
through
external
inductor
6
VCC
4.5 to 5.5
–
Power suplly pin.
Witch biases the internal input transistor. This pin should be externally
equipped with bypass capacitor to minimize its impedance.
2
GND
0
–
Ground pin.
3
This pin should be connected to system ground with minimum
5
inductance. Ground pattern on the board should be formed as wide as
possible.
All the ground pins must be connected together with wide ground pattern
to decrease impedance difference.
Note Pin Voltage is measured at VCC = 5.0 V
Data Sheet PU10491EJ01V0DS
3
UPC3223TB
ABSOLUTE MAXIMUM RATINGS
Parameter
Symbol
Conditions
Ratings
Unit
Supply Voltage
VCC
TA = +25 C, Pin 4 and 6
6.0
V
Total Circuit Current
ICC
TA = +25 C
40
mA
Power Dissipation
PD
TA = +85 C
270
mW
Operating Ambient Temperature
TA
40 to +85
C
Storage Temperature
Tstg
55 to +150
C
Input Power
Pin
+10
dBm
Note
TA = +25 C
Note Mounted on double-sided copper-clad 50
50
1.6 mm epoxy glass PWB
RECOMMENDED OPERATING RANGE
Parameter
Supply Voltage
Symbol
VCC
Conditions
The same voltage should be applied
MIN.
TYP.
MAX.
Unit
4.5
5.0
5.5
V
40
+25
+85
C
to pin 4 and 6.
Operating Ambient Temperature
TA
ELECTRICAL CHARACTERISTICS (TA = +25 C, VCC = Vout = 5.0 V, ZS = ZL = 50
Parameter
Symbol
Test Conditions
)
MIN.
TYP.
MAX.
Unit
Circuit Current
ICC
No input signal
15.0
19.0
24.0
mA
Power Gain
GP
f = 1.0 GHz, Pin = 30 dBm
20.5
23.0
25.5
dB
f = 2.2 GHz, Pin = 30 dBm
20.0
23.0
26.0
f = 1.0 GHz, Pin = 5 dBm
+9.0
+12.0
f = 2.2 GHz, Pin = 5 dBm
+6.0
+9.0
f = 1.0 GHz
+4.5
+6.5
f = 2.2 GHz
+3.0
+5.0
Saturated Output Power
Gain 1 dB Compression Output
PO (sat)
PO (1 dB)
Power
Noise Figure
Upper Limit Operating Frequency
Isolation
Input Return Loss
Output Return Loss
Gain Flatness
4
NF
fu
ISL
RLin
RLout
GP
dBm
dBm
f = 1.0 GHz
4.5
6.0
f = 2.2 GHz
4.0
5.5
dB
3 dB down below flat gain at f = 0.1 GHz
2.8
3.2
GHz
f = 1.0 GHz, Pin = 30 dBm
28.0
33.0
dB
f = 2.2 GHz, Pin = 30 dBm
28.0
33.0
f = 1.0 GHz, Pin = 30 dBm
9.0
12.0
f = 2.2 GHz, Pin = 30 dBm
12.0
17.5
f = 1.0 GHz, Pin = 30 dBm
9.0
12.0
f = 2.2 GHz, Pin = 30 dBm
9.0
12.0
f = 0.1 to 2.2 GHz
Data Sheet PU10491EJ01V0DS
0.9
dB
dB
dB
UPC3223TB
OTHER CHARACTERISTICS, FOR REFERENCE PURPOSES ONLY
(TA = +25 C, VCC = Vout = 5.0 V, ZS = ZL = 50 )
Parameter
Output Intercept Point
Symbol
OIP3
Test Conditions
Reference Value
Unit
f = 1.0 GHz
+17.8
dBm
f = 2.2 GHz
+14.8
Data Sheet PU10491EJ01V0DS
5
UPC3223TB
TEST CIRCUIT
VCC
C4
1 000 pF
1 000 pF
C3
L
100 nH
6
50
C1
C2
4
1
IN
50
OUT
100 pF
100 pF
2, 3, 5
The application circuits and their parameters are for reference only and are not intended for use in actual design-ins.
COMPONENTS OF TEST CIRCUIT FOR
MEASURING ELECTRICAL CHARACTERISTICS
Type
Value
C1, C2
Chip Capacitor
100 pF
C3
Chip Capacitor
1 000 pF
C4
Feed-through Capacitor
1 000 pF
L
Chip Inductor
100 nH
INDUCTOR FOR THE OUTPUT PIN
The internal output transistor of this IC consumes 20 mA, to output medium power. To supply current for output
transistor, connect an inductor between the VCC pin (pin 6) and output pin (pin 4). Select large value inductance, as
listed above.
The inductor has both DC and AC effects. In terms of DC, the inductor biases the output transistor with minimum
voltage drop to output enable high level. In terms of AC, the inductor makes output-port impedance higher to get
enough gain. In this case, large inductance and Q is suitable.
CAPACITORS FOR THE VCC, INPUT AND OUTPUT PINS
Capacitors of 1000 pF are recommendable as the bypass capacitor for the VCC pin and the coupling capacitors for
the input and output pins.
The bypass capacitor connected to the VCC pin is used to minimize ground impedance of VCC pin. So, stable bias
can be supplied against VCC fluctuation.
The coupling capacitors, connected to the input and output pins, are used to cut the DC and minimize RF serial
impedance. Their capacitances are therefore selected as lower impedance against a 50
load. The capacitors thus
perform as high pass filters, suppressing low frequencies to DC.
To obtain a flat gain from 100 MHz upwards, 1 000 pF capacitors are used in the test circuit. In the case of under
10 MHz operation, increase the value of coupling capacitor such as 10 000 pF. Because the coupling capacitors are
determined by equation, C = 1/(2 Rfc).
6
Data Sheet PU10491EJ01V0DS
UPC3223TB
ILLUSTRATION OF THE TEST CIRCUIT ASSEMBLED ON EVALUATION BOARD
IN
C1
C2
OUT
L
C3
C4
COMPONENT LIST
Value
30
0.4 mm double sided copper clad polyimide board.
1.
30
2.
Back side: GND pattern
1 000 pF
3.
Solder plated on pattern
100 nH
4.
: Through holes
C1, C2
100 pF
C3, C4
L
Notes
Data Sheet PU10491EJ01V0DS
7
UPC3223TB
TYPICAL CHARACTERISTICS (TA = +25 C , unless otherwise specified)
CIRCUIT CURRENT vs. SUPPLY VOLTAGE
30
CIRCUIT CURRENT vs.
OPERATING AMBIENT TEMPERATURE
21
No input signal
25
No input signal
VCC = 5.0 V
20
20
19
TA = 85˚C
15
18
TA = 25˚C
10
17
TA = 40˚C
5
16
0
0
1
2
3
4
5
6
15
60
Supply Voltage VCC (V)
40
20
0
POWER GAIN vs. FREQUENCY
40
60
80
100
INPUT RETURN LOSS vs. FREQUENCY
25
10
TA = 25˚C
23
TA = 25˚C
0
VCC = 5.5 V
21
20
Operating Ambient Temperature TA ( C)
VCC = 4.5 V
VCC = 5.0 V
19
10
20
VCC = 4.5 V
VCC = 5.0 V
VCC = 5.5 V
17
30
VCC = 5.0 to 5.5 V
15
0.1
1.1
2.1
3.1
4.1
5.1
40
0.1
1.1
Frequency f (GHz)
3.1
4.1
5.1
Frequency f (GHz)
ISOLATION vs. FREQUENCY
0
2.1
OUTPUT RETURN LOSS vs. FREQUENCY
10
TA = 25˚C
10
0
20
10
TA = 25˚C
VCC = 4.5 V
VCC = 4.5 to 5.5 V
30
20
40
30
VCC = 5.0 V
50
0.1
1.1
2.1
3.1
4.1
5.1
40
0.1
Frequency f (GHz)
1.1
2.1
3.1
Frequency f (GHz)
Remark The graphs indicate nominal characteristics.
8
VCC = 5.5 V
Data Sheet PU10491EJ01V0DS
4.1
5.1
UPC3223TB
POWER GAIN vs. FREQUENCY
INPUT RETURN LOSS vs. FREQUENCY
25
10
VCC = 5.0 V
VCC = 5.0 V
23
0
TA = 85˚C
TA = 40˚C
21
10
19
20
TA = 85˚C
TA = 40˚C
17
30
TA = 25˚C
TA = 25˚C
15
0.1
1.1
3.1
2.1
4.1
5.1
40
0.1
1.1
2.1
3.1
4.1
5.1
Frequency f (GHz)
Frequency f (GHz)
ISOLATION vs. FREQUENCY
OUTPUT RETURN LOSS vs. FREQUENCY
10
0
VCC = 5.0 V
10
0
20
10
VCC = 5.0 V
TA = 40 to 85˚C
30
20
TA = 40 to 85˚C
40
50
0.1
30
1.1
2.1
3.1
4.1
5.1
40
0.1
Frequency f (GHz)
1.1
2.1
3.1
4.1
5.1
Frequency f (GHz)
Remark The graphs indicate nominal characteristics.
Data Sheet PU10491EJ01V0DS
9
UPC3223TB
OUTPUT POWER vs. INPUT POWER
OUTPUT POWER vs. INPUT POWER
15
15
f = 1.0 GHz
TA = 25˚C
10
10
VCC = 5.5 V
5
VCC = 5.0 V
5
VCC = 4.5 V
0
0
5
5
10
10
15
15
20
20
40
35
30
25
20
15
10
5
0
f = 1.0 GHz
VCC = 5.0 V
5
10
TA = 40 to 85˚C
40
35
30
Input Power Pin (dBm)
10
f = 2.2 GHz
TA = 25˚C
10
5
0
5
10
f = 2.2 GHz
VCC = 5.0 V
VCC = 5.0 V
0
0
VCC = 4.5 V
5
5
10
10
15
15
TA = 40 to 85˚C
25
40
35
30
25
20
15
10
5
0
5
10
40
35
30
25
20
15
10
5
0
5
Input Power Pin (dBm)
Input Power Pin (dBm)
OUTPUT POWER (2 tones), IM3
vs. INPUT POWER
OUTPUT POWER (2 tones), IM3
vs. INPUT POWER
20
f1 = 1 000 MHz
10 f2 = 1 001 MHz
VCC = 5.5 V
5.0 V
4.5 V
Pout
0
10
10
20
f1 = 2 200 MHz
10 f2 = 2 201 MHz
Pout
VCC = 5.5 V
5.0 V
4.5 V
0
10
20
IM3
20
IM3
30
30
VCC = 4.5 V
40
50
VCC = 5.0 V
60
60
VCC = 5.5 V
40
35
30
VCC = 4.5 to 5.5 V
40
50
25
20
15
10
5
0
5
10
70
Input Power Pin (dBm)
40
35
30
25
20
15
10
5
Input Power Pin (dBm)
Remark The graphs indicate nominal characteristics.
10
10
5
VCC = 5.5 V
70
15
OUTPUT POWER vs. INPUT POWER
15
5
20
20
Input Power Pin (dBm)
OUTPUT POWER vs. INPUT POWER
15
25
Data Sheet PU10491EJ01V0DS
0
5
10
UPC3223TB
S-PARAMETERS (TA = +25 C, VCC = Vout = 5.0 V)
S11 FREQUENCY
1.0 GHz
2.2 GHz
S22 FREQUENCY
1.0 GHz
2.2 GHz
Data Sheet PU10491EJ01V0DS
11
UPC3223TB
PACKAGE DIMENSIONS
6-PIN SUPER MINIMOLD (UNIT: mm)
12
Data Sheet PU10491EJ01V0DS
UPC3223TB
NOTES ON CORRECT USE
(1) Observe precautions for handling because of electro-static sensitive devices.
(2) Form a ground pattern as widely as possible to minimize ground impedance (to prevent undesired oscillation).
All the ground pins must be connected together with wide ground pattern to decrease impedance difference.
(3) The bypass capacitor should be attached to VCC line.
(4) The inductor must be attached between VCC and output pins. The inductance value should be determined in
accordance with desired frequency.
(5) The DC cut capacitor must be each attached to input and output pin.
RECOMMENDED SOLDERING CONDITIONS
This product should be soldered and mounted under the following recommended conditions.
For soldering
methods and conditions other than those recommended below, contact your nearby sales office.
Soldering Method
Infrared Reflow
Wave Soldering
Soldering Conditions
Condition Symbol
Peak temperature (package surface temperature)
: 260 C or below
Time at peak temperature
: 10 seconds or less
Time at temperature of 220 C or higher
: 60 seconds or less
Preheating time at 120 to 180 C
: 120 30 seconds
Maximum number of reflow processes
: 3 times
Maximum chlorine content of rosin flux (% mass)
: 0.2%(Wt.) or below
Peak temperature (molten solder temperature)
: 260 C or below
Time at peak temperature
: 10 seconds or less
IR260
WS260
Preheating temperature (package surface temperature) : 120 C or below
Partial Heating
Maximum number of flow processes
: 1 time
Maximum chlorine content of rosin flux (% mass)
: 0.2%(Wt.) or below
Peak temperature (pin temperature)
: 350 C or below
Soldering time (per side of device)
: 3 seconds or less
Maximum chlorine content of rosin flux (% mass)
: 0.2%(Wt.) or below
HS350
Caution Do not use different soldering methods together (except for partial heating).
Data Sheet PU10491EJ01V0DS
13
Subject: Compliance with EU Directives
CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant
with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous
Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive
2003/11/EC Restriction on Penta and Octa BDE.
CEL Pb-free products have the same base part number with a suffix added. The suffix –A indicates
that the device is Pb-free. The –AZ suffix is used to designate devices containing Pb which are
exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals.
All devices with these suffixes meet the requirements of the RoHS directive.
This status is based on CEL’s understanding of the EU Directives and knowledge of the materials that
go into its products as of the date of disclosure of this information.
Restricted Substance
per RoHS
Concentration Limit per RoHS
(values are not yet fixed)
Concentration contained
in CEL devices
-A
Not Detected
Lead (Pb)
< 1000 PPM
Mercury
< 1000 PPM
Not Detected
Cadmium
< 100 PPM
Not Detected
Hexavalent Chromium
< 1000 PPM
Not Detected
PBB
< 1000 PPM
Not Detected
PBDE
< 1000 PPM
Not Detected
-AZ
(*)
If you should have any additional questions regarding our devices and compliance to environmental
standards, please do not hesitate to contact your local representative.
Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance
content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information
provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better
integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate
information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL
suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for
release.
In no event shall CEL’s liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to
customer on an annual basis.
See CEL Terms and Conditions for additional clarification of warranties and liability.