EMC2DXV5T1, EMC3DXV5T1, EMC5DXV5T1 Preferred Devices Dual Common Base−Collector Bias Resistor Transistors http://onsemi.com NPN and PNP Silicon Surface Mount Transistors with Monolithic Bias Resistor Network 3 2 R1 The BRT (Bias Resistor Transistor) contains a single transistor with a monolithic bias network consisting of two resistors; a series base resistor and a base−emitter resistor. These digital transistors are designed to replace a single device and its external resistor bias network. The BRT eliminates these individual components by integrating them into a single device. In the EMC2DXV5T1 series, two complementary BRT devices are housed in the SOT−553 package which is ideal for low power surface mount applications where board space is at a premium. • Simplifies Circuit Design • Reduces Board Space • Reduces Component Count • Available in 8 mm, 7 inch Tape and Reel • Lead Free 1 R2 Q2 R2 Q1 R1 4 5 MARKING DIAGRAM 5 5 1 SOT−553 CASE 463B xx D 1 xx = Specific Device Code D = Date Code MAXIMUM RATINGS (TA = 25°C unless otherwise noted, common for Q1 and Q2, − minus sign for Q1 (PNP) omitted) ORDERING INFORMATION Symbol Value Unit Collector-Base Voltage VCBO 50 Vdc Collector-Emitter Voltage VCEO 50 Vdc IC 100 mAdc Rating Collector Current Device Package Shipping† EMC2DXV5T1 SOT−553 4 mm pitch 4000/Tape & Reel EMC2DXV5T5 SOT−553 2 mm pitch 8000/Tape & Reel EMC3DXV5T1 SOT−553 4 mm pitch 4000/Tape & Reel EMC3DXV5T5 SOT−553 2 mm pitch 8000/Tape & Reel EMC5DXV5T1 SOT−553 4 mm pitch 4000/Tape & Reel EMC5DXV5T5 SOT−553 2 mm pitch 8000/Tape & Reel THERMAL CHARACTERISTICS Characteristic (One Junction Heated) Symbol Max Unit 357 (Note 1) 2.9 (Note 1) mW mW/°C RJA 350 (Note 1) °C/W Symbol Max Unit 500 (Note 1) 4.0 (Note 1) mW mW/°C RJA 250 (Note 1) °C/W TJ, Tstg −55 to +150 °C Total Device Dissipation TA = 25°C Derate above 25°C Thermal Resistance − Junction-to-Ambient Characteristic (Both Junctions Heated) PD Total Device Dissipation TA = 25°C Derate above 25°C Thermal Resistance − Junction-to-Ambient Junction and Storage Temperature PD 1. FR−4 @ Minimum Pad Semiconductor Components Industries, LLC, 2003 September, 2003 − Rev. 2 1 †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. Preferred devices are recommended choices for future use and best overall value. Publication Order Number: EMC2DXV5T1/D EMC2DXV5T1, EMC3DXV5T1, EMC5DXV5T1 DEVICE MARKING AND RESISTOR VALUES Transistor 1 − PNP Device EMC2DXV5T1 EMC3DXV5T1 EMC5DXV5T1 Transistor 2 − NPN Marking R1 (K) R2 (K) R1 (K) R2 (K) UC U3 U5 22 10 4.7 22 10 10 22 10 47 22 10 47 ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted) Characteristic Symbol Min Typ Max Unit Collector-Base Cutoff Current (VCB = 50 V, IE = 0) ICBO − − 100 nAdc Collector-Emitter Cutoff Current (VCB = 50 V, IB = 0) ICEO − − 500 nAdc IEBO − − − − − − 0.2 0.5 1.0 mAdc Collector-Base Breakdown Voltage (IC = 10 A, IE = 0) V(BR)CBO 50 − − Vdc Collector-Emitter Breakdown Voltage (IC = 2.0 mA, IB = 0) V(BR)CEO 50 − − Vdc hFE 60 35 20 100 60 35 − − − OFF CHARACTERISTICS Q1 TRANSISTOR: PNP Emitter-Base Cutoff Current (VEB = 6.0, IC = 5.0 mA) EMC2DXV5T1 EMC3DXV5T1 EMC5DXV5T1 ON CHARACTERISTICS DC Current Gain (VCE = 10 V, IC = 5.0 mA) EMC2DXV5T1 EMC3DXV5T1 EMC5DXV5T1 Collector−Emitter Saturation Voltage (IC = 10 mA, IB = 0.3 mA) VCE(SAT) − − 0.25 Vdc Output Voltage (on) (VCC = 5.0 V, VB = 2.5 V, RL = 1.0 k) VOL − − 0.2 Vdc Output Voltage (off) (VCC = 5.0 V, VB = 0.5 V, RL = 1.0 k) VOH 4.9 − − Vdc k Input Resistor EMC2DXV5T1 EMC3DXV5T1 EMC5DXV5T1 R1 15.4 7.0 3.3 22 10 4.7 28.6 13 6.1 Resistor Ratio EMC2DXV5T1 EMC3DXV5T1 EMC5DXV5T1 R1/R2 0.8 0.8 0.38 1.0 1.0 0.47 1.2 1.2 0.56 Collector-Base Cutoff Current (VCB = 50 V, IE = 0) ICBO − − 100 nAdc Collector-Emitter Cutoff Current (VCB = 50 V, IB = 0) ICEO − − 500 nAdc IEBO − − − − − − 0.2 0.5 0.1 mAdc Collector-Base Breakdown Voltage (IC = 10 A, IE = 0) V(BR)CBO 50 − − Vdc Collector-Emitter Breakdown Voltage (IC = 2.0 mA, IB = 0) V(BR)CEO 50 − − Vdc hFE 60 35 80 100 60 140 − − − VCE(SAT) − − 0.25 Vdc Q2 TRANSISTOR: NPN OFF CHARACTERISTICS Emitter-Base Cutoff Current (VEB = 6.0, IC = 5.0 mA) EMC2DXV5T1 EMC3DXV5T1 EMC5DXV5T1 ON CHARACTERISTICS DC Current Gain (VCE = 10 V, IC = 5.0 mA) EMC2DXV5T1 EMC3DXV5T1 EMC5DXV5T1 Collector−Emitter Saturation Voltage (IC = 10 mA, IB = 0.3 mA) Output Voltage (on) (VCC = 5.0 V, VB = 2.5 V, RL = 1.0 k) VOL − − 0.2 Vdc Output Voltage (off) (VCC = 5.0 V, VB = 0.5 V, RL = 1.0 k) VOH 4.9 − − Vdc k Input Resistor EMC2DXV5T1 EMC3DXV5T1 EMC5DXV5T1 R1 15.4 7.0 33 22 10 47 28.6 13 61 Resistor Ratio EMC2DXV5T1 EMC3DXV5T1 EMC5DXV5T1 R1/R2 0.8 0.8 0.8 1.0 1.0 1.0 1.2 1.2 1.2 http://onsemi.com 2 EMC2DXV5T1, EMC3DXV5T1, EMC5DXV5T1 PD , POWER DISSIPATION (MILLIWATTS) 250 200 150 100 50 0 −50 RJA = 833°C/W 0 50 100 TA, AMBIENT TEMPERATURE (°C) Figure 1. Derating Curve http://onsemi.com 3 150 EMC2DXV5T1, EMC3DXV5T1, EMC5DXV5T1 1000 10 VCE = 10 V IC/IB = 10 1 hFE, DC CURRENT GAIN VCE(sat) , MAXIMUM COLLECTOR VOLTAGE (VOLTS) TYPICAL ELECTRICAL CHARACTERISTICS — EMC2DXV5T1 PNP TRANSISTOR 25°C TA=−25°C 75°C 0.1 0.01 0 40 20 IC, COLLECTOR CURRENT (mA) TA=75°C 100 10 50 10 1 Figure 3. DC Current Gain 100 IC, COLLECTOR CURRENT (mA) 3 2 1 10 20 30 40 VR, REVERSE BIAS VOLTAGE (VOLTS) TA=−25°C 10 1 0.1 0.01 0.001 50 Figure 4. Output Capacitance 100 25°C 75°C f = 1 MHz lE = 0 mA TA = 25°C V in , INPUT VOLTAGE (VOLTS) Cob , CAPACITANCE (pF) 4 0 VO = 5 V 0 1 2 3 4 5 6 7 Vin, INPUT VOLTAGE (VOLTS) VO = 0.2 V 10 25°C 75°C 1 0 10 8 9 Figure 5. Output Current versus Input Voltage TA=−25°C 0.1 100 IC, COLLECTOR CURRENT (mA) Figure 2. VCE(sat) versus IC 0 25°C −25°C 20 30 IC, COLLECTOR CURRENT (mA) 40 Figure 6. Input Voltage versus Output Current http://onsemi.com 4 50 10 EMC2DXV5T1, EMC3DXV5T1, EMC5DXV5T1 1 1000 IC/IB = 10 VCE = 10 V TA=−25°C 25°C hFE, DC CURRENT GAIN VCE(sat) , MAXIMUM COLLECTOR VOLTAGE (VOLTS) TYPICAL ELECTRICAL CHARACTERISTICS — EMC2DXV5T1 NPN TRANSISTOR 0.1 75°C 0.01 0.001 0 20 40 IC, COLLECTOR CURRENT (mA) TA=75°C 25°C −25°C 100 10 50 1 10 IC, COLLECTOR CURRENT (mA) Figure 7. VCE(sat) versus IC Figure 8. DC Current Gain 100 IC, COLLECTOR CURRENT (mA) 2 1 0 0 10 20 30 40 VR, REVERSE BIAS VOLTAGE (VOLTS) 25°C 75°C f = 1 MHz IE = 0 mA TA = 25°C 1 0.1 0.01 0.001 50 TA=−25°C 10 VO = 5 V 0 1 2 3 4 5 6 7 Vin, INPUT VOLTAGE (VOLTS) 10 VO = 0.2 V TA=−25°C 25°C 75°C 1 0.1 0 10 8 9 10 Figure 10. Output Current versus Input Voltage Figure 9. Output Capacitance V in , INPUT VOLTAGE (VOLTS) Cob , CAPACITANCE (pF) 4 3 100 20 30 IC, COLLECTOR CURRENT (mA) 40 Figure 11. Input Voltage versus Output Current http://onsemi.com 5 50 EMC2DXV5T1, EMC3DXV5T1, EMC5DXV5T1 1000 1 TA=−25°C 0.1 25°C 75°C 0.01 0 20 25°C 100 10 −25°C 10 IC, COLLECTOR CURRENT (mA) Figure 12. VCE(sat) versus IC Figure 13. DC Current Gain 50 1 100 IC, COLLECTOR CURRENT (mA) f = 1 MHz lE = 0 mA TA = 25°C 3 2 1 0 10 20 30 40 VR, REVERSE BIAS VOLTAGE (VOLTS) TA=−25°C 10 1 0.1 0.01 0.001 50 100 VO = 5 V 0 1 2 3 4 5 6 7 Vin, INPUT VOLTAGE (VOLTS) VO = 0.2 V TA=−25°C 25°C 75°C 1 0 10 8 9 Figure 15. Output Current versus Input Voltage 10 0.1 100 25°C 75°C Figure 14. Output Capacitance V in , INPUT VOLTAGE (VOLTS) 0 TA=75°C IC, COLLECTOR CURRENT (mA) 40 4 Cob , CAPACITANCE (pF) VCE = 10 V IC/IB = 10 hFE , DC CURRENT GAIN VCE(sat) , MAXIMUM COLLECTOR VOLTAGE (VOLTS) TYPICAL ELECTRICAL CHARACTERISTICS — EMC3DXV5T1 PNP TRANSISTOR 20 30 IC, COLLECTOR CURRENT (mA) 40 Figure 16. Input Voltage versus Output Current http://onsemi.com 6 50 10 EMC2DXV5T1, EMC3DXV5T1, EMC5DXV5T1 1000 1 25°C TA=−25°C 0.1 75°C 0.01 0.001 0 20 TA=75°C 25°C −25°C 100 10 50 40 1 100 10 IC, COLLECTOR CURRENT (mA) IC, COLLECTOR CURRENT (mA) Figure 17. VCE(sat) versus IC Figure 18. DC Current Gain 4 100 3 IC, COLLECTOR CURRENT (mA) f = 1 MHz IE = 0 mA TA = 25°C 2 1 75°C 25°C TA=−25°C 10 1 0.1 0.01 VO = 5 V 0 0 0.001 50 10 20 30 40 VR, REVERSE BIAS VOLTAGE (VOLTS) Figure 19. Output Capacitance 2 0 4 6 Vin, INPUT VOLTAGE (VOLTS) VO = 0.2 V TA=−25°C 10 25°C 75°C 1 0.1 0 10 8 10 Figure 20. Output Current versus Input Voltage 100 V in , INPUT VOLTAGE (VOLTS) Cob , CAPACITANCE (pF) VCE = 10 V IC/IB = 10 hFE, DC CURRENT GAIN VCE(sat) , MAXIMUM COLLECTOR VOLTAGE (VOLTS) TYPICAL ELECTRICAL CHARACTERISTICS — EMC3DXV5T1 NPN TRANSISTOR 20 30 40 IC, COLLECTOR CURRENT (mA) Figure 21. Input Voltage versus Output Current http://onsemi.com 7 50 EMC2DXV5T1, EMC3DXV5T1, EMC5DXV5T1 1000 1 VCE = 10 V IC/IB = 10 TA=75°C 0.1 0.01 hFE, DC CURRENT GAIN VCE(sat) , MAXIMUM COLLECTOR VOLTAGE (VOLTS) TYPICAL ELECTRICAL CHARACTERISTICS — EMC5DXV5T1 PNP TRANSISTOR 25°C −25°C 0 10 20 30 50 40 100 1 60 1 10 100 IC, COLLECTOR CURRENT (mA) IC, COLLECTOR CURRENT (mA) Figure 22. VCE(sat) versus IC Figure 23. DC Current Gain 1000 100 IC, COLLECTOR CURRENT (mA) f = 1 MHz IE = 0 mA TA = 25°C 10 Cob , CAPACITANCE (pF) 25°C −25°C 10 12 8 6 4 SERIES 1 2 0 TA=75°C 0 5 10 20 30 15 25 35 VR, REVERSE BIAS VOLTAGE (VOLTS) 40 1 Figure 24. Output Capacitance VO = 5 V 0.1 0.01 45 75°C 10 TA=−25°C 25°C 0 2 4 6 8 Vin, INPUT VOLTAGE (VOLTS) 10 12 Figure 25. Output Current versus Input Voltage http://onsemi.com 8 EMC2DXV5T1, EMC3DXV5T1, EMC5DXV5T1 10 1000 VCE = 10 V IC/IB = 10 hFE, DC CURRENT GAIN VCE(sat) , MAXIMUM COLLECTOR VOLTAGE (VOLTS) TYPICAL ELECTRICAL CHARACTERISTICS — EMC5DXV5T1 NPN TRANSISTOR 1 25°C TA=−25°C 75°C 0.1 0.01 0 TA=75°C 25°C −25°C 100 10 50 20 40 IC, COLLECTOR CURRENT (mA) 10 IC, COLLECTOR CURRENT (mA) 1 Figure 26. VCE(sat) versus IC 1 100 IC, COLLECTOR CURRENT (mA) 0.4 0.2 0 0 25°C 75°C 0.6 TA=−25°C 10 1 0.1 0.01 0.001 50 10 20 30 40 VR, REVERSE BIAS VOLTAGE (VOLTS) VO = 5 V 0 2 4 6 Vin, INPUT VOLTAGE (VOLTS) 100 VO = 0.2 V TA=−25°C 10 25°C 75°C 1 0.1 0 10 8 10 Figure 29. Output Current versus Input Voltage Figure 28. Output Capacitance V in , INPUT VOLTAGE (VOLTS) Cob , CAPACITANCE (pF) Figure 27. DC Current Gain f = 1 MHz IE = 0 mA TA = 25°C 0.8 100 20 30 40 50 IC, COLLECTOR CURRENT (mA) Figure 30. Input Voltage versus Output Current http://onsemi.com 9 EMC2DXV5T1, EMC3DXV5T1, EMC5DXV5T1 INFORMATION FOR USING THE SOT−553 SURFACE MOUNT PACKAGE MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS Surface mount board layout is a critical portion of the total design. The footprint for the semiconductor packages must be the correct size to insure proper solder connection interface between the board and the package. With the correct pad geometry, the packages will self align when subjected to a solder reflow process. 0.3 0.0118 0.45 0.0177 1.0 0.0394 1.35 0.0531 0.5 0.5 0.0197 0.0197 SCALE 20:1 mm inches SOT−553 SOT−553 POWER DISSIPATION SOLDERING PRECAUTIONS The power dissipation of the SOT−553 is a function of the pad size. This can vary from the minimum pad size for soldering to a pad size given for maximum power dissipation. Power dissipation for a surface mount device is determined by TJ(max), the maximum rated junction temperature of the die, RJA, the thermal resistance from the device junction to ambient, and the operating temperature, TA. Using the values provided on the data sheet for the SOT−553 package, PD can be calculated as follows: PD = The melting temperature of solder is higher than the rated temperature of the device. When the entire device is heated to a high temperature, failure to complete soldering within a short time could result in device failure. Therefore, the following items should always be observed in order to minimize the thermal stress to which the devices are subjected. • Always preheat the device. • The delta temperature between the preheat and soldering should be 100°C or less.* • When preheating and soldering, the temperature of the leads and the case must not exceed the maximum temperature ratings as shown on the data sheet. When using infrared heating with the reflow soldering method, the difference shall be a maximum of 10°C. • The soldering temperature and time shall not exceed 260°C for more than 10 seconds. • When shifting from preheating to soldering, the maximum temperature gradient shall be 5°C or less. • After soldering has been completed, the device should be allowed to cool naturally for at least three minutes. Gradual cooling should be used as the use of forced cooling will increase the temperature gradient and result in latent failure due to mechanical stress. • Mechanical stress or shock should not be applied during cooling. TJ(max) − TA RJA The values for the equation are found in the maximum ratings table on the data sheet. Substituting these values into the equation for an ambient temperature TA of 25°C, one can calculate the power dissipation of the device which in this case is 150 milliwatts. PD = 150°C − 25°C 833°C/W = 150 milliwatts The 833°C/W for the SOT−553 package assumes the use of the recommended footprint on a glass epoxy printed circuit board to achieve a power dissipation of 150 milliwatts. There are other alternatives to achieving higher power dissipation from the SOT−553 package. Another alternative would be to use a ceramic substrate or an aluminum core board such as Thermal Clad. Using a board material such as Thermal Clad, an aluminum core board, the power dissipation can be doubled using the same footprint. * Soldering a device without preheating can cause excessive thermal shock and stress which can result in damage to the device. http://onsemi.com 10 EMC2DXV5T1, EMC3DXV5T1, EMC5DXV5T1 PACKAGE DIMENSIONS SOT−553 XV5 SUFFIX 5−LEAD PACKAGE CASE 463B−01 ISSUE O A −X− 5 C K NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETERS 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4 1 2 B −Y− 3 D G S J 5 PL 0.08 (0.003) M X Y http://onsemi.com 11 DIM A B C D G J K S MILLIMETERS MIN MAX 1.50 1.70 1.10 1.30 0.50 0.60 0.17 0.27 0.50 BSC 0.08 0.18 0.10 0.30 1.50 1.70 INCHES MIN MAX 0.059 0.067 0.043 0.051 0.020 0.024 0.007 0.011 0.020 BSC 0.003 0.007 0.004 0.012 0.059 0.067 EMC2DXV5T1, EMC3DXV5T1, EMC5DXV5T1 Thermal Clad is a trademark of the Bergquist Company. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder Japan: ON Semiconductor, Japan Customer Focus Center 2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051 Phone: 81−3−5773−3850 http://onsemi.com 12 For additional information, please contact your local Sales Representative. EMC2DXV5T1/D