INTEGRATED CIRCUITS DATA SHEET TDA3505 TDA3506 Video control combination circuit with automatic cut-off control Product specification File under Integrated Circuits, IC02 November 1987 Philips Semiconductors Product specification Video control combination circuit with automatic cut-off control TDA3505 TDA3506 GENERAL DESCRIPTION The TDA3505 and TDA3506 are monolithic integrated circuits which perform video control functions in a PAL/SECAM decoder. The TDA3505 is for negative colour difference signals −(R-Y), −(B-Y) and the TDA3506 is for positive colour difference signals +(R-Y), +(B-Y). The required input signals are: luminance and colour difference (negative or positive) and a 3-level sandcastle pulse for control purposes. Linear RGB signals can be inserted from an external source. RGB output signals are available for driving the video output stages. The circuits provide automatic cut-off control of the picture tube. • Linear contrast and brightness controls, operating on both the inserted and matrixed RGB signals Features • Capacitive coupling of the colour difference and luminance input signals with black level clamping in the input stages • Peak beam current limiting input • Clamping, horizontal and vertical blanking of the three input signals controlled by a 3-level sandcastle pulse • Linear saturation control acting on the colour difference signals • 3 DC gain controls for the RGB output signals (white point adjustment) • (G-Y) and RGB matrix • Emitter-follower outputs for driving the RGB output stages • Linear transmission of inserted signals • Equal black levels for inserted and matrixed signals • Input for automatic cut-off control with compensation for leakage current of the picture tube • 3 identical channels for the RGB signals QUICK REFERENCE DATA PARAMETER CONDITIONS SYMBOL MIN. TYP. MAX. UNIT Supply voltage (pin 6) VP = V6-24 − 12 − V Supply current IP = I6 − 95 − mA V15-24(p-p) − 0,45 − V −(B-Y) or +(B-Y) respectively V18-24(p-p) − 1,33 − V −(R-Y) or +(R-Y) respectively V17-24(p-p) − 1,05 − V Composite video input signal (peak-to-peak value) Colour difference input signals (peak-to-peak value) Inserted RGB signals V (black-to-white value) Three-level sandcastle pulse V12,13,14-24 − 1,0 − V V10-24 − 2,5 − V − 4,5 − V − 8,0 − V Control voltage ranges brightness V20-24 1,0 − 3,0 V contrast V19-24 2,0 − 4,3 V saturation V16-24 2,0 − 4,3 V PACKAGE OUTLINE 28-lead DIL; plastic (SOT117); SOT117-1; 1996 November 20. November 1987 2 Philips Semiconductors Product specification November 1987 3 Fig.1 Part of block diagram; continued in Fig. 2 TDA3505 TDA3506 Note Colour difference inputs are negative for TDA3505 or positive for TDA3506. Video control combination circuit with automatic cut-off control Philips Semiconductors Product specification TDA3505 TDA3506 Fig.2 Part of block diagram; continued from Fig. 1 Video control combination circuit with automatic cut-off control November 1987 4 Philips Semiconductors Product specification Video control combination circuit with automatic cut-off control TDA3505 TDA3506 PINNING PIN DESCRIPTION 1 red output 2 green storage capacitor for cut-off control 3 green output 4 blue storage capacitor for cut-off control 5 blue output 6 positive supply voltage (+ 12 V) 7 blue storage for brightness 8 green storage for brightness 9 red storage for brightness 10 sandcastle pulse input 11 fast switch for RGB inputs 12 blue input (external signal) 13 green input (external signal) 14 red input (external signal) 15 luminance input 16 saturation control input 17 colour difference input − (R-Y) or + (R-Y) respectively 18 colour difference input − (B-Y) or + (B-Y) respectively 19 contrast control input 20 brightness control input 21 white point adjustment, blue 22 white point adjustment, green 23 white point adjustment, red 24 ground (0 V) 25 control input for peak beam current limiting 26 automatic cut-off control input 27 storage capacitor for leakage current 28 red storage capacitor for cut-off control November 1987 5 Philips Semiconductors Product specification Video control combination circuit with automatic cut-off control TDA3505 TDA3506 RATINGS Limiting values in accordance with the Absolute Maximum System (IEC134) PARAMETER SYMBOL MIN. MAX. UNIT VP = V6-24 − 13,2 V at pins 10, 21, 22, 23, 25, 26 Vn-24 0 VP V at pin 11 V11-24 −0,5 3,0 V at pins 16, 19, 20 V16, 19, 20-24 0 0,5VP V Supply voltage (pin 6) Voltage ranges at pins 1, 2, 3, 4, 5, 7, 8, 9, 12, 13, 14, 15, 17, 18, 27, 28 no external DC voltage Currents at pins 1, 3, 5 −I1, 3, 5 − 3 mA at pin 19 I19 − 10 mA at pin 20 I20 − 5 mA at pin 25 −I25 − 5 mA Total power dissipation Ptot − 1,7 W Storage temperature range Tstg −25 +150 °C Operating ambient temperature range Tamb 0 +70 °C November 1987 6 Philips Semiconductors Product specification Video control combination circuit with automatic cut-off control TDA3505 TDA3506 CHARACTERISTICS VP = V6-24 = 12,0 V; V12, 13, 14(p-p) = 1,0 V; V15-24(p-p) = 0,45 V; V17-24(p-p) = 1,05 V; V18-24(p-p) = 1,33 V; Tamb = 25°C; measured in Fig.3; nominal settings of brightness, contrast, saturation and white point adjustment; all voltages are referred to pin 24; unless otherwise specified PARAMETER CONDITIONS SYMBOL MIN. TYP. MAX. UNIT Supply (pin 6) Supply voltage VP = V6 10,8 12,0 13,2 V Supply current IP − 95 125(1) mA V17(p-p) − 1,05 1,48 V V18(p-p) − 1,33 1,88 V Input current during scanning I17, 18 − − 1,0 µA Input resistance R17, 18-24 1,0 − − MΩ note 2 V17, 18 3,8 4,4 4,8 V note 2 V16 4,0 4,2 4,4 V note 2 V16 2,9 3,1 3,3 V note 2 V16 1,9 2,1 2,3 V V16 = 1,8 V d 46 50 − dB I16 − − 20 µA Colour difference inputs (pins 17, 18) (R-Y) input signal (pin 17) (peak-to-peak value) for saturated colour bar with 75% of maximum amplitude (B-Y) input signal (pin 18) (peak-to-peak value) for saturated colour bar with 75% of maximum amplitude Internal DC voltage due to clamping Saturation control (pin 16) Control voltage for maximum saturation Control voltage for nominal saturation 6 dB below max. Control voltage for −26 dB saturation referred to maximum Minimum saturation Input current (G-Y) matrix Matrixed according to the equation V(G-Y) = − 0,51 V(R-Y) − 0,19 V(B-Y) November 1987 7 Philips Semiconductors Product specification Video control combination circuit with automatic cut-off control PARAMETER CONDITIONS TDA3505 TDA3506 SYMBOL MIN. TYP. MAX. UNIT Luminance input (pin 15) Composite video input signal V15(p-p) − 450 630 mV Input resistance R15-24 100 − − kΩ Input capacitance C15-24 − − 5 pF Input current during scanning I15 − − 1 µA nominal settings m 0,85 − − note 2 V15 2,5 2,9 3,3 V Normal state; no insertion V11 0 − 0,4 V Level for insertion-on V11 0,9 − 3,0 V (peak-to-peak value) Linearity Internal DC voltage due to clamping RGB channels Signal switching input (pin 11) C11-24 − − 10 pF I11 −100 − +450 µA V12, 13, 14 − 1,0 1,4 V I12, 13, 14 − − 1,0 µA V12, 13, 14 4,0 4,5 5,0 V V19 4,0 4,2 4,4 V V19 3,4 3,6 3,8 V V19 2,6 2,8 3,0 V V19 = 2 V d 18 21 29 dB V25 > 6 V I19 − − 2 µA − − 0,6 dB Input capacitance Input current V11 = 0 to 3 V Signal insertion (pins 12, 13, 14) External RGB input signals (black-to-white value) Input current during scanning Internal DC voltage due to clamping Contrast control (pin 19) notes 2, 3 note 2 Control voltage for maximum contrast Control voltage for nominal contrast 3 dB below max. Control voltage for −10 dB below max. Minimum contrast referred to max. Input current Difference between RGB channels contrast −10 dB below max. November 1987 8 Philips Semiconductors Product specification Video control combination circuit with automatic cut-off control PARAMETER CONDITIONS TDA3505 TDA3506 SYMBOL MIN. TYP. MAX. UNIT Peak beam current limiting (pin 25) V25 5,3 5,5 5,7 V R25-24 − 10 − kΩ I19 10 20 34 mA Control voltage range V20 1 − 3 V Input current −I20 − − 10 µA − ± 50 − % 95 − − % black − −25 − % white 115 120 125 % Gv − 100 − % V21, 22, 23 = 0 V Gv −35 −40 − % V21, 22, 23 = 12 V Gv +35 +40 − % R21,22,23-24 − 20 − kΩ Internal DC bias voltage note 2 Input resistance Input current at contrast control input Brightness code (pin 20) V25 = 4,5 V note 2 Change of black level in the control range related to the luminance signal (black/white) ∆V20 = 1 V Tracking Internal signal limiting (RGB) Signal limiting referred to nominal luminance and nominal black level White point adjustment (pins 21, 22, 23) AC voltage gain note 2 note 4 V21, 22, 23 = 5,5 V Input resistance November 1987 9 Philips Semiconductors Product specification Video control combination circuit with automatic cut-off control PARAMETER CONDITIONS TDA3505 TDA3506 SYMBOL MIN. TYP. MAX. UNIT RGB outputs (emitter follower) (pins 1, 3, 5) Output voltage; black-to-white positive V1, 3, 5 1,5 2,0 2,5 V V1, 3, 5 6,1 6,9 7,7 V ∆V1, 3, 5 − − 10 mV V1, 3, 5 4,0 4,6 − V I1, 3, 5 2,0 3,0 − mA V26 0 − 6,5 V V26 0,5 0,64 0,72 V G1,3,5-15 14 16 18 dB d1,3,5-15 − − 3 dB 3 6 9 dB − − 3 dB Black level without automatic cut-off control note 2; V28,2,4 = 10 V Difference in black level between RGB channels due to variation of contrast control Cut-off control range note 2 Internal current source Automatic cut-off control (pin 26) notes 2, 5 Input voltage range Voltage difference between cut-off current measurement (note 6) and leakage current measurement (note 7) Input pin 26 switches to ground during horizontal flyback Gain data at nominal brightness, contrast, saturation and white point settings Voltage gain with respect to luminance input (pin 15) Frequency response of luminance path 0 to 5 MHz Voltage gain with respect to colour difference inputs (pins 17 and 18) G5-18 G1-17 Frequency response of colour difference paths November 1987 0 to 2 MHz d5-18 d1-17 10 Philips Semiconductors Product specification Video control combination circuit with automatic cut-off control PARAMETER CONDITIONS TDA3505 TDA3506 SYMBOL MIN. TYP. MAX. UNIT Voltage gain with respect to inserted signals G1-14 G3-13 4 6 8 dB − − 3 dB tr, tf − 40 − ns ∆t1, 3, 5 − 0 15 ns td −25 − +25 ns ∆G1,3,5 − − 10 % V10 1,0 1,5 2,0 V required pulses (H+V) V10 2,1 2,5 2,9 V horizontal pulses V10 3,0 3,5 4,0 V V10 4,1 4,5 5,0 V V10 6,5 7,0 7,5 V required pulses V10 7,6 − 12,0 V no keying V10 − − 1,0 V −I10 − − 110 µA G5-12 Frequency response of inserted signal paths 0 to 10 MHz d1-14 d3-13 d5-12 Rise and fall times of RGB output signals (pins 1, 3, 5) Difference in transit times between R, G and B channels Delay time between signal switching and signal insertion Difference in gain between normal mode and signal insertion mode Sandcastle pulse detector (pin 10) note 8 Levels for separating the following pulses: horizontal and vertical blanking pulses note 9 required pulses (H) clamping pulses note 10 Input current November 1987 11 Philips Semiconductors Product specification Video control combination circuit with automatic cut-off control TDA3505 TDA3506 Notes 1. < 110 mA after warm-up. 2. Values are proportional to the supply voltage. 3. When V11-24 < 0,4 V during clamping time - the black levels of the inserted RGB signals are clamped on the black levels of the internal RGB signals. When V11-24 > 0,9 V during clamping time - the black levels of the inserted RGB signals are clamped on an internal DC voltage (correct clamping of the external RGB signals is possible only when they are synchronous with the sandcastle pulse). 4. When pins 21, 22 and 23 are not connected, an internal bias voltage of 5,5 V is supplied. 5. Automatic cut-off control measurement occurs in the following lines after start of the vertical blanking pulse: line 20: measurement of leakage current (R + G + B) line 21: measurement of red cut-off current line 22: measurement of green cut-off current line 23: measurement of blue cut-off current 6. Black level of the measured channel is nominal; the other two channels are blanked to ultra-black. 7. All three channels blanked to ultra-black. The cut-off control cycle occurs when the vertical blanking part of the sandcastle pulse contains more than 3 line pulses. The internal blanking continues until the end of the last measured line. The vertical blanking pulse is not allowed to contain more than 34 line pulses, otherwise another control cycle begins. 8. The sandcastle pulse is compared with three internal thresholds (proportional to VP) and the given levels separate the various pulses. 9. Blanked to ultra-black (−25%). 10. Pulse duration ≥ 3,5 µs. November 1987 12 Philips Semiconductors Product specification Video control combination circuit with automatic cut-off control TDA3505 TDA3506 (1) When supplied via a 75 Ω line. (2) Capacitor value depends on circuit layout. Fig.3 Typical application circuit diagram using TDA3505 or TDA3506; colour difference inputs are negative for TDA3505 or positive for TDA3506. November 1987 13 Philips Semiconductors Product specification Video control combination circuit with automatic cut-off control TDA3505 TDA3506 PACKAGE OUTLINE seating plane handbook, full pagewidthdual in-line package; 28 leads (600 mil) DIP28: plastic SOT117-1 ME D A2 L A A1 c e Z w M b1 (e 1) b MH 15 28 pin 1 index E 1 14 0 5 10 mm scale DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT A max. A1 min. A2 max. b b1 c D (1) E (1) e e1 L ME MH w Z (1) max. mm 5.1 0.51 4.0 1.7 1.3 0.53 0.38 0.32 0.23 36.0 35.0 14.1 13.7 2.54 15.24 3.9 3.4 15.80 15.24 17.15 15.90 0.25 1.7 inches 0.20 0.020 0.16 0.066 0.051 0.020 0.014 0.013 0.009 1.41 1.34 0.56 0.54 0.10 0.60 0.15 0.13 0.62 0.60 0.68 0.63 0.01 0.067 Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC SOT117-1 051G05 MO-015AH November 1987 EIAJ EUROPEAN PROJECTION ISSUE DATE 92-11-17 95-01-14 14 Philips Semiconductors Product specification Video control combination circuit with automatic cut-off control TDA3505 TDA3506 SOLDERING Introduction There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for surface mounted ICs, or for printed-circuits with high population densities. In these situations reflow soldering is often used. This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our “IC Package Databook” (order code 9398 652 90011). Soldering by dipping or by wave The maximum permissible temperature of the solder is 260 °C; solder at this temperature must not be in contact with the joint for more than 5 seconds. The total contact time of successive solder waves must not exceed 5 seconds. The device may be mounted up to the seating plane, but the temperature of the plastic body must not exceed the specified maximum storage temperature (Tstg max). If the printed-circuit board has been pre-heated, forced cooling may be necessary immediately after soldering to keep the temperature within the permissible limit. Repairing soldered joints Apply a low voltage soldering iron (less than 24 V) to the lead(s) of the package, below the seating plane or not more than 2 mm above it. If the temperature of the soldering iron bit is less than 300 °C it may remain in contact for up to 10 seconds. If the bit temperature is between 300 and 400 °C, contact may be up to 5 seconds. DEFINITIONS Data sheet status Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. Product specification This data sheet contains final product specifications. Limiting values Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. November 1987 15