REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5962-R051-94. 93-11-30 K. A. Cottongim B Add device types 09 through 24. 95-01-19 K. A. Cottongim C Changes in accordance with NOR 5962-R121-95. 95-04-27 K. A. Cottongim D Changes in accordance with NOR 5962-R014-96. 95-12-15 K. A. Cottongim E Add device types 25 and 26. Add case outlines T and U. 98-06-11 K. A. Cottongim F Correct figure 1, case outline Z, pin 1 index. 98-09-11 K. A. Cottongim G Add device types 27 through 46 and case outlines M and N. 01-05-23 Raymond Monnin H Paragraph 1.2.2, device types 38, 39, 40, and 41, circuit function for device types 38 and 40, remove -15 V and for device types 39 and 41, remove -15 V. Remove remaining supply references to aforementioned device types throughout document. 02-07-15 Raymond Monnin REV SHEET REV H H H H H H H H H H H H H H H SHEET 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 REV STATUS REV H H H H H H H H H H H H H H OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Steve Duncan STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A DEFENSE SUPPLY CENTER COLUMBUS POST OFFICE BOX 3990 COLUMBUS, OHIO 43216-5000 http://www.dscc.dla.mil CHECKED BY Michael C. Jones APPROVED BY Kendall A. Cottongim MICROCIRCUIT, HYBRID, LINEAR, MIL-STD-1553, BC/RTU/MT, MULTIPLEXED TERMINAL DRAWING APPROVAL DATE 93-09-17 REVISION LEVEL H SIZE A CAGE CODE 5962-93065 67268 SHEET DSCC FORM 2233 APR 97 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. 1 OF 29 5962-E501-02 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 Federal stock class designator \ RHA designator (see 1.2.1) 93065 01 Device type (see 1.2.2) / H Device class designator (see 1.2.3) X Case outline (see 1.2.4) X Lead finish (see 1.2.5) \/ Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number 01 BU-65170X1 BU-65170BX1 BU-65170X2 BU-65170BX2 BU-61580X1 BU-61580BX1 BU-61580X2 BU-61580BX2 BU-65171X1 BU-65171BX1 BU-65171X2 BU-65171BX2 BU-61581X1 BU-61581BX1 BU-61581X2 BU-61581BX2 BU-65170CX3 BU-65170CX6 BU-61580CX3 BU-61580CX6 BU-65171CX3 BU-65171CX6 BU-61581CX3 BU-61581CX6 BU-61585X1 BU-61585X2 BU-61586X1 BU-61586X2 BU-61585BX3 BU-61585BX6 BU-61586BX3 BU-61586BX6 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Circuit function MIL-STD-1553, RT, 4K RAM, +5/-15 V transceiver MIL-STD-1553, RT, 4K RAM, +5/-15 V transceiver MIL-STD-1553, RT, 4K RAM, +5/-12 V transceiver MIL-STD-1553, RT, 4K RAM, +5/-12 V transceiver MIL-STD-1553, BC/RT/MT, 4K RAM, +5/-15 V transceiver MIL-STD-1553, BC/RT/MT, 4K RAM, +5/-15 V transceiver MIL-STD-1553, BC/RT/MT, 4K RAM, +5/-12 V transceiver MIL-STD-1553, BC/RT/MT, 4K RAM, +5/-12 V transceiver MIL-STD-1553, RT, 4K RAM, +5/-15 V transceiver, RT address latch MIL-STD-1553, RT, 4K RAM, +5/-15 V transceiver, RT address latch MIL-STD-1553, RT, 4K RAM, +5/-12 V transceiver, RT address latch MIL-STD-1553, RT, 4K RAM, +5/-12 V transceiver, RT address latch MIL-STD-1553, BC/RT/MT, 4K RAM, +5/-15 V transceiver, RT address latch MIL-STD-1553, BC/RT/MT, 4K RAM, +5/-15 V transceiver, RT address latch MIL-STD-1553, BC/RT/MT, 4K RAM, +5/-12 V transceiver, RT address latch MIL-STD-1553, BC/RT/MT, 4K RAM, +5/-12 V transceiver, RT address latch MIL-STD-1553, RT, 4K RAM, +5 V transceiver MIL-STD-1553, RT, 4K RAM, +5 V transceiver MIL-STD-1553, BC/RT/MT, 4K RAM, +5 V transceiver MIL-STD-1553, BC/RT/MT, 4K RAM, +5 V transceiver MIL-STD-1553, RT, 4K RAM, +5 V transceiver, RT address latch MIL-STD-1553, RT, 4K RAM, +5 V transceiver, RT address latch MIL-STD-1553, BC/RT/MT, 4K RAM, +5 V transceiver, RT address latch MIL-STD-1553, BC/RT/MT, 4K RAM, +5 V transceiver, RT address latch MIL-STD-1553, BC/RT/MT, 12K RAM, +5/-15 V transceiver MIL-STD-1553, BC/RT/MT, 12K RAM, +5/-12 V transceiver MIL-STD-1553, BC/RT/MT, 12K RAM, +5/-15 V transceiver, RT address latch MIL-STD-1553, BC/RT/MT, 12K RAM, +5/-12 V transceiver, RT address latch MIL-STD-1553, BC/RT/MT, 12K RAM, +5 V transceiver MIL-STD-1553, BC/RT/MT, 12K RAM, +5 V transceiver MIL-STD-1553, BC/RT/MT, 12K RAM, +5 V transceiver, RT address latch MIL-STD-1553, BC/RT/MT, 12K RAM, +5 V transceiver, RT address latch STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93065 A REVISION LEVEL H SHEET 2 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: - Continued. Device type Generic number 25 26 27 28 29 30 31 32 33 34 35 BU-61588BX3 BU-65178BX3 BU-65179BX3 BU-61688AX3 BU-61689AX3 BU-65170DX3 BU-65170DX6 BU-61580DX3 BU-61580DX6 BU-65171DX3 BU-65171DX6 36 37 BU-61581DX3 BU-61581DX6 38 39 40 41 42 43 44 45 46 BU-61585DX3 BU-61585DX6 BU-61586DX3 BU-61586DX6 BU-61588CX3 BU-65178CX3 BU-65179CX3 BU-61688BX3 BU-61689BX3 Circuit function MIL-STD-1553, BC/RT/MT, 4K RAM, +5 V transceiver MIL-STD-1553, RT, 4K RAM, +5 V transceiver MIL-STD-1553, RT/RT_BOOT, 10, 12, 16, 20 MHz, 4K RAM, +5 V transceiver MIL-STD-1553, BC/RT/MT, 12/16 MHz, 64K RAM, +5 V transceiver MIL-STD-1553, BC/RT/MT, 10/20 MHz, 64K RAM, +5 V transceiver MIL-STD-1553, RT, 4K RAM, +5 V transceiver MIL-STD-1553, RT, 4K RAM, +5 V transceiver, with TX inhibits external MIL-STD-1553, BC/RT/MT, 4K RAM, +5 V transceiver MIL-STD-1553, BC/RT/MT, 4K RAM, +5 V transceiver, with TX inhibits external MIL-STD-1553, RT, 4K RAM, +5 V transceiver, RT address latch MIL-STD-1553, RT, 4K RAM, +5 V transceiver, RT address latch, with TX inhibits external MIL-STD-1553, BC/RT/MT, 4K RAM, +5 V transceiver, RT address latch MIL-STD-1553, BC/RT/MT, 4K RAM, +5 V transceiver, RT address latch, with TX inhibits external MIL-STD-1553, BC/RT/MT, 12K RAM, +5 V transceiver MIL-STD-1553, BC/RT/MT, 12K RAM, +5 V transceiver MIL-STD-1553, BC/RT/MT, 12K RAM, +5 V transceiver, RT address latch MIL-STD-1553, BC/RT/MT, 12K RAM, +5 V transceiver, RT address latch MIL-STD-1553, BC/RT/MT, 12/16 MHz, 4K RAM, +5 V transceiver MIL-STD-1553, RT, 4K RAM, +5 V transceiver MIL-STD-1553, RT/RT_BOOT, 10, 12, 16, 20 MHz, 4K RAM, +5 V transceiver MIL-STD-1553, BC/RT/MT, 12/16 MHz, 64K RAM, +5 V transceiver MIL-STD-1553, BC/RT/MT, 10/20 MHz, 64K RAM, +5 V transceiver 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals M N T U X Y Z See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 72 70 72 81 70 70 70 STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 Package style Quad flat package with lead forming Flat package with lead forming Quad flat package with tie bars Pin grid array Dual-in-line Flat package Dual-in-line, J-lead SIZE 5962-93065 A REVISION LEVEL H SHEET 3 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Positive supply voltage range (+5VA, +5VB)............................................................ Negative supply voltage range (-VA, -VB)................................................................ Logic supply voltage range (+5 V logic) ................................................................... Power dissipation (PD): 2/ 3/ 4/ Device types 01, 03, 05, 07, 17, 19, 38, and 40 ................................................... Device types 27, 28, 29, 44, 45, 46 ...................................................................... Device types 02, 04, 06, 08, 18, 20, 39, and 41 ................................................... Device types 09 through 16, 21 through 24, 30 through 37 .................................. Device types 25, 26, 42, and 43 ........................................................................... Storage temperature range ...................................................................................... Lead temperature (soldering, 10 seconds)............................................................... Thermal resistance, junction to case (θJC) .............................................................. -0.3 V dc to +7.0 V dc +0.3 V dc to -18 V dc -0.3 V dc to +6.0 V dc 2.23 W 2.08 W 2.16 W 2.85 W 1.97 W -65°C to +150°C +300°C 6.99°C/W 3/ 1.4 Recommended operating conditions. Positive supply voltage range (+5VA, +5VB): Device types 01 through 08, 17 through 20, 38 through 41 .................................. Device types 09 through 16, 21 through 29, 30 through 37, 42 through 46.......... Negative supply voltage range (-VA, -VB): Device types 01, 03, 05, 07, 17, and 19 ............................................................... Device types 02, 04, 06, 08, 18, and 20 ............................................................... Logic supply voltage range (+5V logic) .................................................................... Minimum logic high input voltage (VIH) .................................................................... Maximum logic low input voltage (VIL) ..................................................................... Operating frequency (FOP) ...................................................................................... Case operating temperature range (TC) .................................................................. +4.5 V dc to +5.5 V dc +4.75 V dc to +5.25 V dc -14.25 V dc to -15.75 V dc -11.40 V dc to -12.60 V dc +4.5 V dc to +5.5 V dc 2.0 V dc 0.8 V dc 10, 12, 16, or 20 MHz -55°C to +125°C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation. SPECIFICATION DEPARTMENT OF DEFENSE MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. STANDARDS DEPARTMENT OF DEFENSE MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. 1/ 2/ 3/ 4/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Applies up to TC = +125°C. Hottest die. Assumes 100 percent transmitter duty cycle on one channel and 0 percent duty cycle on the other channel. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93065 A REVISION LEVEL H SHEET 4 HANDBOOKS DEPARTMENT OF DEFENSE MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as designated in the device manufacturer's Quality Management (QM) plan or as designated for the applicable device class. Therefore, the tests and inspections herein may not be performed for the applicable device class (see MIL-PRF-38534). Furthermore, the manufacturer may take exceptions or use alternate methods to the tests and inspections herein and not perform them. However, the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Pin functions. The pin functions shall be as specified in table III. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DSCC-VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DSCC-VA shall affirm that the manufacturer's product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93065 A REVISION LEVEL H SHEET 5 TABLE I. Electrical performance characteristics. Test +5 volt supply current, Idle 1/ +5 volt supply current, channel A = 25% duty cycle channel B = idle 1/ +5 volt supply current, channel A = idle channel B = 25% duty cycle 1/ Symbol ICC1 ICC2 ICC3 Conditions -55°C ≤ TC ≤ +125°C unless otherwise specified Group A subgroups Limits Device type Min 1,2,3 +5 V logic = +5.5 V, +5VA = +5VB = +5.5 V 1,2,3 +5 V logic = +5.5 V, +5VA = +5VB = +5.5 V 1,2,3 +5 V logic = +5.5 V, +5VA = +5VB = +5.5 V Unit Max 01-08 5 190 09-16, 25-37, 42-46 5 200 17-20 5 250 21-24 38-41 5 260 01-08 5 190 09-16, 25-37, 42-46 5 350 17-20 5 250 21-24, 38-41 5 398 01-08 5 190 09-16, 25-37, 42-46 17-20 21-24, 38-41 5 350 5 5 250 398 mA mA mA Negative supply current 2/ IEE1 -VA = -12 V for device types 02, 04, 06, 08, 18, and 20. -VA = -15 V for device types 01, 03, 05, 07, 17, and 19. 1,2,3 01-08, 17-20 5 60 mA Negative supply current, channel A = 25% duty cycle channel B = idle 2/ IEE2 -VA = -12 V for device types 02, 04, 06, 08, 18, and 20. -VA = -15 V for device types 01, 03, 05, 07, 17, and 19. 1,2,3 01,03, 05,07, 17,19 25 108 mA 02,04, 06,08, 18,20 25 120 See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93065 A REVISION LEVEL H SHEET 6 TABLE I. Electrical performance characteristics - Continued. Test Negative supply current, channel A = idle channel B = 25% duty cycle 2/ Symbol IEE3 Conditions -55°C ≤ TC ≤ +125°C unless otherwise specified Group A subgroups Limits Device type Min -VA = -12 V for device types 02, 04, 06, 08, 18, and 20. -VA = -15 V for device types 01, 03, 05, 07, 17, and 19. 1,2,3 Unit Max 01,03, 05,07, 17,19 25 108 02,04, 06,08, 18,20 25 120 mA Low level input current 3/ IIL1 +5 V logic = +5.5 V, +5VA = +5VB = +5.5 V, VIN = 0 V 1,2,3 All -397 -50 µA Low level input current 4/ IIL2 +5 V logic = +5.5 V, +5VA = +5VB = +5.5 V, VIN = 0 V 1,2,3 All -794 -100 µA High level input current 3/ IIH1 +5 V logic = +5.5 V, +5VA = +5VB = +5.5 V, VIN = 2.4 V 1,2,3 All -346 -42 µA High level input current 4/ IIH2 +5 V logic = +5.5 V, +5VA = +5VB = +5.5 V, VIN = 2.4 V 1,2,3 All -692 -84 µA Output voltage low 5/ VOL1 +5 V logic = +5.5 V, +5VA = +5VB = +5.5 V, IOL = -6.4 mA 1,2,3 All 0.4 V Output voltage low 6/ VOL2 +5 V logic = +5.5 V, +5VA = +5VB = +5.5 V, IOL = -3.2 mA 1,2,3 All 0.4 V Output voltage high 5/ VOH1 +5 V logic = +5.5 V, +5VA = +5VB = +5.5 V, IOH = 6.4 mA 1,2,3 All 2.4 V Output voltage high 6/ VOH2 +5 V logic = +5.5 V, +5VA = +5VB = +5.5 V, IOH = 3.2 mA 1,2,3 All 2.4 V See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93065 A REVISION LEVEL H SHEET 7 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -55°C ≤ TC ≤ +125°C unless otherwise specified Group A subgroups Limits Device type Min Unit Max IOEN low pulse width (memory read) tPW1 +5 V logic = +5.5 V, +5VA = +5VB = +5.5 V 9,10,11 All 475 625 ns READYD low pulse width (memory read) tPW2 +5 V logic = +5.5 V, +5VA = +5VB = +5.5 V 9,10,11 All 225 375 ns MEMOE low pulse width (memory read) tPW3 +5 V logic = +5.5 V, +5VA = +5VB = +5.5 V 9,10,11 All 350 500 ns MEMWR low pulse width (memory write) tPW4 +5 V logic = +5.5 V, +5VA = +5VB = +5.5 V 9,10,11 All 37 87 ns MEMENA-OUT low pulse width (memory read) tPW5 +5 V logic = +5.5 V, +5VA = +5VB = +5.5 V 9,10,11 All 412 562 ns MEMENA-OUT low pulse width (memory write) tPW6 +5 V logic = +5.5 V, +5VA = +5VB = +5.5 V 9,10,11 All 435 695 ns INCMD low pulse width (receive command) tPW7 +5 V logic = +5.5 V, +5VA = +5VB = +5.5 V 9,10,11 All 45.4 47.5 µs INCMD low pulse width (transmit command) tPW8 +5 V logic = +5.5 V, +5VA = +5VB = +5.5 V 9,10,11 All 45.4 47.5 µs INT low pulse width tPW9 +5 V logic = +5.5 V, +5VA = +5VB = +5.5 V 9,10,11 All DTREQ low pulse width tPW10 +5 V logic = +5.5 V, +5VA = +5VB = +5.5 V 9,10,11 All 2.07 2.19 µs DTACK low pulse width tPW11 +5 V logic = +5.5 V, +5VA = +5VB = +5.5 V 9,10,11 All 2.0 2.23 µs +5 V logic = +5.5 V, +5VA = +5VB = +5.5 V, see 4.3.1b. 7,8 All Functional tests 450 550 ns Pass/ fail See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93065 A REVISION LEVEL H SHEET 8 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -55°C ≤ TC ≤ +125°C unless otherwise specified Group A subgroups Limits Device type Min Unit Max Receiver threshold VTH +5 V logic = +5.5 V, +5VA = +5VB = +5.5 V, transformer coupled into a 70 Ω resistive load 4,5,6 All 500 700 Transmitter differential output voltage 7/ VO +5 V logic = +5.5 V, +5VA = +5VB = +5.5 V, transformer coupled into a 70 Ω resistive load 4,5,6 All 18 27 Transmitter output rise time tR +5 V logic = +5.5 V, +5VA = +5VB = +5.5 V, transformer coupled into a 70 Ω resistive load 4,5,6 All 100 300 ns Transmitter output fall time tF +5 V logic = +5.5 V, +5VA = +5VB = +5.5 V, transformer coupled into a 70 Ω resistive load 4,5,6 All 100 300 ns Transmitter output offset voltage 8/ VOS +5 V logic = +5.5 V, +5VA = +5VB = +5.5 V, transformer coupled into a 70 Ω resistive load 4,5,6 All -250 +250 1/ 2/ 3/ 4/ 5/ 6/ 7/ 8/ mVp-p Vp-p mVp-p Measured at the following pins: Case outlines M and T: pins 20, 37, and 72. Case outline U: pins A9, D3, and J3. Case outlines N, X, Y, and Z: pins 38, 54, and 68. Measured at the following pins: Case outlines N, X, Y, and Z: pins 36 and 70. Measured at the following pins: Device types 01-08, 10, 12, 14, 16-20, 22, 24, 31, 33, 35, 37, 39, and 41: pins 3-17, 1926, 29-33, 39-44, 46-53, and 55-64. Device types 09, 11, 13, 15, 21, 23, 27-30, 32, 34, 36, 38, 40, 44, 45, and 46: pins 3-17, 19-26, 29-33, 36, 39-44, 46-53, 55-64, and 70. Device types 25, 26, 42 and 43, case outlines M and T: pins 1-4, 6, 8-12, 14, 15, 21-24, 27-31, 33-36, 38-55, 59-64, 66, and 68-71. Device types 25, 26, 42, and 43, case outline U: pins A1, A2, A5, A6, B1-B5, B7, B9, C2-C7, C9, D2, D7-D9, E1-E3, E7-E9, F1-F3, F7-F9, G2-G9, H5-H9, J1, J2, J4-J7, and J9. Measured at the following pin. Case outlines M and T: pin 32. Case outline U: pin H2. Case outlines N, X, Y, and Z: pin 7. Measured at the following pins: Case outlines M and T: pins 3, 4, 6, 8-12, 14, 15, 22-24, 27, 29, 36, 38, 39, 42-54, 66, and 68-71. Case outline U: pins A1, A2, B1-B3, B9, C2-C5, D2, D7-D9, E1-E3, E7-E9, F1-F3, F7-F9, G2-G6, H5, H9, J1, J2, J4, and J6. Case outlines N, X, Y, and Z: pins 8-17, 20-25, 29-32, 46-53, and 55-62. Measured at the following pins: Case outlines M and T: pins 56, 57, and 58. Case outline U: pins A3, B8, and C8. Case outlines N, X, Y, and Z: pins 28, 45, and 65-67. For device types 01, 03, 05, 17, 19: In case outline X, the limits are 20 Vp-p minimum and 27 Vp-p maximum. In case outlines N, Y and Z, the limits are 18 Vp-p minimum and 27 Vp-p maximum. Parameter shall be tested as part of the initial characterization of these devices and after design and process changes. Parameter shall be guaranteed to the limits specified in table I for all lots not specifically tested. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93065 A REVISION LEVEL H SHEET 9 Case outline M. FIGURE 1. Case outline(s). STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93065 A REVISION LEVEL H SHEET 10 Case outline M. Millimeters Symbol Minimum Inches Maximum Minimum Maximum A --- 3.94 --- 0.155 A1 1.14 1.40 0.045 0.055 A2 0.05 0.41 0.002 0.016 b 0.41 0.51 0.016 0.020 c 0.20 0.30 0.008 0.012 e 1.14 1.40 0.045 0.055 D/E 34.54 35.56 1.360 1.400 D1/E1 25.15 25.65 0.990 1.010 D2/E2 25.65 26.37 1.010 1.038 D3/E3 18.35 25.40 0.842 0.858 L 4.57 5.08 0.180 0.200 L1 2.03 --- 0.080 --- L2 1.27 --- 0.050 --- R --- 0.30 --- 0.012 NOTES: 1. There are eight test pads located on the bottom of the package. Each pad measures 0.100 inch (2.54 mm) in diameter. These pads are recessed so as to not interfere when mounting the package. 2. The U.S. government preferred system of measurement is the metric SI. This case outline was designed using inchpound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 3. Package material is Alumina (AL2O3). 4. Test pads P5 and P8 are not applicable to device types 28 through 31 and 42 through 46. FIGURE 1. Case outline(s) - Continued. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93065 A REVISION LEVEL H SHEET 11 Case outline N. FIGURE 1. Case outline(s) - Continued. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93065 A REVISION LEVEL H SHEET 12 Case outline N - Continued. Millimeters Symbol Minimum A --- Inches Maximum Minimum 3.81 Maximum --- 0.150 A1 1.68 REF 0.066 REF A2 1.02 TYP 0.040 TYP A3 0.05 0.41 0.002 0.016 b 0.41 0.51 0.016 0.020 c 0.20 0.30 0.008 0.012 D --- 48.26 --- 1.900 D1 43.05 43.31 1.695 1.705 E 34.54 35.56 1.360 1.400 E1 --- 26.01 --- 1.024 E2 --- 25.40 --- 1.000 e 1.27 TYP 0.050 TYP L 4.47 5.08 0.180 0.200 L1 2.03 --- 0.080 --- L2 1.27 --- 0.050 --- L3 --- 0.31 --- 0.012 NOTES: 1. The U.S. government preferred system of measurement is the metric SI. This case outline was designed using inchpound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Pin numbers are for reference only. FIGURE 1. Case outline(s) - Continued. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93065 A REVISION LEVEL H SHEET 13 Case outline T. FIGURE 1. Case outline(s) - Continued. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93065 A REVISION LEVEL H SHEET 14 Case outline T - Continued. Millimeters Symbol Minimum Inches Maximum Minimum Maximum A --- 3.94 --- 0.155 A1 2.03 2.54 0.080 0.100 A2 1.14 1.40 0.045 0.055 A3 0.76 1.02 0.030 0.040 b 0.41 0.51 0.016 0.020 c 0.20 0.30 0.008 0.012 e 1.14 1.40 0.045 0.055 D/E 50.42 51.18 1.985 2.015 D1/E1 25.15 25.65 0.990 1.010 D2/E2 25.65 26.37 1.010 1.038 D3/E3 18.35 25.40 0.842 0.858 D4/E4 12.19 13.21 0.480 0.520 D5/E5 4.95 5.21 0.195 0.205 NOTES: 1. There are eight test pads located on the bottom of the package. Each pad measures 0.100 inch (2.54 mm) in diameter. These pads are recessed so as to not interfere when mounting the package. 2. The U.S. government preferred system of measurement is the metric SI. This case outline was designed using inchpound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 3. Package material is Alumina (AL2O3). 4. Test pads P5 and P8 are not applicable to device types 28 through 31 and 42 through 46. FIGURE 1. Case outline(s) - Continued. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93065 A REVISION LEVEL H SHEET 15 Case outline U. Symbol A B ∅b ∅b2 D/E D1/E1 e L Millimeters Minimum Maximum --3.94 1.61 1.91 0.41 0.51 1.61 1.91 25.15 25.65 20.19 20.45 2.41 2.67 4.37 4.78 Inches Minimum Maximum --0.155 0.065 0.075 0.016 0.020 0.065 0.075 0.990 1.010 0.795 0.805 0.095 0.105 0.172 0.188 NOTES: 1. The U.S. government preferred system of measurement is the metric SI. This case outline was designed using inchpound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Package material is Alumina (AL2O3). FIGURE 1. Case outline(s) - Continued. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93065 A REVISION LEVEL H SHEET 16 Case outline X. Symbol A ∅b b2 D e eA e1 e2 e3 E L Millimeters Minimum Maximum --5.46 0.406 0.508 1.65 1.91 --48.26 2.41 2.67 10.03 10.29 43.05 43.31 1.14 1.40 15.11 15.37 --25.40 4.32 4.83 Inches Minimum Maximum --0.215 0.016 0.020 0.065 0.075 --1.900 0.095 0.105 0.395 0.405 1.695 1.705 0.045 0.055 0.595 0.605 --1.000 0.170 0.190 NOTES: 1. The U.S. government preferred system of measurement is the metric SI. This case outline was designed using inchpound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Pin numbers are for reference only. FIGURE 1. Case outline(s) - Continued. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93065 A REVISION LEVEL H SHEET 17 Case outline Y. Symbol A c D e e1 e2 e3 E L Millimeters Minimum Maximum --5.46 0.330 0.432 --48.26 1.14 1.40 43.05 43.31 0.20 0.30 1.52 2.03 --25.40 10.16 --- Inches Minimum Maximum --0.215 0.013 0.017 --1.900 0.045 0.055 1.695 1.705 0.008 0.012 0.060 0.080 --1.000 0.400 --- NOTES: 1. The U.S. government preferred system of measurement is the metric SI. This case outline was designed using inchpound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Pin numbers are for reference only. FIGURE 1. Case outline(s) - Continued. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93065 A REVISION LEVEL H SHEET 18 Case outline Z. Symbol A A1 b b2 c D e e1 e2 E E1 R Millimeters Minimum Maximum 6.05 7.06 1.52 1.93 0.38 0.48 0.58 0.69 0.15 0.25 --48.26 1.27 BSC 43.05 43.31 0.84 1.09 --25.98 --25.40 0.635 0.889 Inches Minimum Maximum 0.238 0.278 0.060 0.076 0.015 0.019 0.023 0.027 0.006 0.010 --1.900 0.050 BSC 1.695 1.705 0.033 0.043 --1.023 --1.000 0.025 0.035 NOTES: 1. The U.S. government preferred system of measurement is the metric SI. This case outline was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Braze fillet shall be concave and is .020 ±.005 inches, (.508 ±.127 mm) at an angle of 45 degrees. 3. Pin numbers are for reference only. FIGURE 1. Case outline(s) - Continued. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93065 A REVISION LEVEL H SHEET 19 Device types 25 through 29 and 42 through 46 Case outlines M and T Terminal number Terminal symbol 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 MEM/REG MSTCLR A11 A10 TX/RX-A A08 TX/RX-A A14 A04 A03 A07 A02 TX/RX-B MEMOE/ADDR_LAT A00 TX/RX-B LOGIC GND LOGIC GND LOGIC GND +5 V LOGIC RTAD2 A06 MEMWR/ZERO_WAIT 24 25 DTREQ/16/8 Test output (RX_B) 26 27 28 29 30 31 Test output (RX_B) A01 MENENA_IN/TRIGGER_SEL DTACK/POLARITY_SEL CLOCK_IN RT_AD_LAT 32 33 34 35 36 SSFLAG/EXT_TRIG RTAD0 TRAD3 RTAD4 D06 Terminal number Terminal symbol 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 +5 V LOGIC D01 D04 RTADP RTADI D00 D02 D03 D05 D08 D07 D13 D12 D14 D09 D11 D15 D10 TRANSPARENT/BUFFERED READYD INT IOEN TX_INH_A TX_INH_B 61 62 63 64 65 66 67 68 69 70 71 72 SELECT STRBD RD/WR DTGRT/MSB/LSB Test output (RX-A) A15 Test output (RX-A) A05 A09 A12 A13 +5 V LOGIC FIGURE 2. Terminal connections. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93065 A REVISION LEVEL H SHEET 20 Device types 25 through 29 and 42 through 46 Case outline U Terminal number Terminal symbol Terminal number A1 A2 A3 A4 A5 A6 A7 A8 A9 B1 B2 B3 B4 B5 B6 B7 D10 D11 IOEN Test output (RX-A) RD/WR STRBD LOGIC GND LOGIC GND +5 V LOGIC A13 D12 A 12 MEM/REG MSTCLR Test output (RX-A) TX_INH_A B8 B9 C1 C2 C3 C4 C5 READYD D09 TX/RX-A A11 A10 A14 A15 C6 C7 SELECT TX_INH_B C8 C9 D1 D2 D3 D4 D5 D6 D7 D8 D9 E1 E2 E3 E4 E5 INT TRANPARENT/BUFFERED TX/RX-A A08 +5 V LOGIC Test output (A_RExt) Test output (A_Test1) Test output (AB_Test4) D13 D15 D14 A07 A05 A04 Test output(B_RExt) No connect E6 E7 E8 E9 F1 F2 F3 F4 F5 F6 F7 F8 F9 G1 G2 G3 G4 G5 G6 G7 G8 G9 H1 H2 H3 H4 H5 H6 H7 H8 H9 J1 J2 J3 J4 J5 J6 J7 J8 J9 Terminal symbol Test output (AB_Tstck) D08 D06 D07 A06 A03 A02 Test output(AB_Test2) Test output(AB_Test3) Test output(B_Test1) D03 D01 D02 TX/RX-B A01 A00 MEMOE/ADDR_LAT D05 D04 RT_AD_LAT RTAD3 RTADP TX/RX-B SSFLAG/EXT_TRIG Test output (RX-B) Test output (RX-B) DTREQ/16//8 CLOCK_IN RTAD0 RTAD4 D00 DTGRT/MSB/LSB MEMWR/ZERO_WAIT +5 V LOGIC A09 MEMNA_IN/TRIGGER_SEL DTACK/POLARITY_SEL RTAD2 LOGIC GND RTAD1 FIGURE 2. Terminal connections- Continued. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93065 A REVISION LEVEL H SHEET 21 Device types Case outlines Terminal number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 01 through 24 and 30 through 41 Terminal symbol TX/RX-A TX/RX-A SELECT STRBD MEM/REG RD/WR MSTCLR A15 A14 A13 A12 A11 A10 A09 A08 A07 A06 LOGIC GND CLOCK_IN A05 A04 A03 A02 A01 A00 DTGRT/MSB/LSB SSFLAG/EXT_TRIG MEMENA_OUT MEMOE/ADDR_LAT MEMWR/ZERO_WAIT DTREQ/16/8 DTACK/POLARITY_SEL MEMENA_IN/TRIGGER_SEL TX/RX-B TX/RX-B N, X, Y, and Z Terminal number Terminal symbol -VB (see note 1) GNDB +5VB RTAD0 RTAD1 RTAD2 RTAD3 RTAD4 RTADP INCMD D00 D01 D02 D03 D04 D05 D06 D07 +5 V LOGIC D08 D09 D10 D11 D12 D13 D14 D15 TAG_CLK TRANSPARENT/BUFFERED INT READYD IOEN +5VA GNDA -VA (see note 1) 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 NOTE: 1. For device types 01, 03, 05, 07, 17, and 19; pin 36 and pin 70 are -15 V. For device types 02, 04, 06, 08, 18, and 20; pin 36 and pin 70 are -12 V. For device types 09, 11, 13, 15, 21, 23, 30, 32, 34, 36, 38, and 40; pin 36 and pin 70 are no connects. For device types 10, 12, 14, 16, 22, 24, 31, 33, 35, 37, 39, and 41; pin 36 and pin 70 are TX_INH_B and TX_INH_A, respectively. FIGURE 2. Terminal connections - Continued. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93065 A REVISION LEVEL H SHEET 22 TABLE II. Electrical test requirements. MIL-PRF-38534 test requirements Subgroups (in accordance with MIL-PRF-38534, group A test table) Interim electrical parameters 1,2,3,4,5,6,7,8,9,10,11 Final electrical parameters 1*,2,3,4,5,6,7,8,9,10,11 Group A test requirements 1,2,3,4,5,6,7,8,9,10,11 Group C end-point electrical parameters 1,2,3,4,5,6,7,8,9,10,11 Not applicable End-point electrical parameters for radiation hardness assurance (RHA) devices * PDA applies to subgroup 1. 4. QUALITY ASSURANCE PROVISIONS 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. 4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. b. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DSCC-VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1015 of MIL-STD-883. (2) TA as specified in accordance with table I of method 1015 of MIL-STD-883. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. 4.3 Conformance and periodic inspections. Conformance inspection (CI) and periodic inspection (PI) shall be in accordance with MIL-PRF-38534 and as specified herein. 4.3.1 Group A inspection (CI). Group A inspection shall be in accordance with MIL-PRF-38534 and as follows: a. Tests shall be as specified in table II herein. b. Subgroups 7 and 8 shall consist of verifying the functionality of the device. It forms a part of the vendors test tape and shall be maintained and available from the approved source of supply. 4.3.2 Group B inspection (PI). Group B inspection shall be in accordance with MIL-PRF-38534. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93065 A REVISION LEVEL H SHEET 23 4.3.3 Group C inspection (PI). Group C inspection shall be in accordance with MIL-PRF-38534 and as follows: a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test, method 1005 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DSCC-VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1005 of MIL-STD-883. (2) TA as specified in accordance with table I of method 1005 of MIL-STD-883. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. 4.3.4 Group D inspection (PI). Group D inspection shall be in accordance with MIL-PRF-38534. 4.3.5 Radiation Hardness Assurance (RHA) inspection. RHA inspection is not currently applicable to this drawing. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38534. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractorprepared specification or drawing. 6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for the individual documents. This coordination will be accomplished in accordance with MIL-PRF-38534. 6.4 Record of users. Military and industrial users shall inform Defense Supply Center Columbus when a system application requires configuration control and the applicable SMD. DSCC will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices (FSC 5962) should contact DSCC-VA, telephone (614) 692-0544. 6.5 Comments. Comments on this drawing should be directed to DSCC-VA, Post Office Box 3990, Columbus, Ohio 432165000, or telephone (614) 692-0512. 6.6 Sources of supply. Sources of supply are listed in MIL-HDBK-103 and QML-38534. The vendors listed in MIL-HDBK103 and QML-38534 have submitted a certificate of compliance (see 3.7 herein) to DSCC-VA and have agreed to this drawing. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93065 A REVISION LEVEL H SHEET 24 TABLE III. Pin functions. Terminal symbol I/O Description D00 I/O Data bus bit 0 (LSB). D02 I/O Data bus bit 2. D04 I/O Data bus bit 4. D06 I/O Data bus bit 6. D08 I/O Data bus bit 8. D10 I/O Data bus bit 10. D12 I/O Data bus bit 12. D14 I/O Data bus bit 14. RTAD1 I Remote terminal address bit 1. RTAD0 I Remote terminal address bit 0 (LSB). RTAD4 I Remote terminal address bit 4 (MSB). +5 V LOGIC I +5 volt supply input for digital logic section. TAG CLK I External Time Tag Clock Input for BC/RT modes. -VB I Input power supply connection for the B channel transceiver. -15 V for device types 01, 03, 05, 07, 17, and 19, -12 V for device types 02, 04, 06, 08, 18, and 20. GNDB - Ground B. Power supply return connection for the B channel transceiver. TX/RX-B I/O LOGIC GND - Transmit/receive transceiver-B. Input/output to the coupling transformer that connects to the B channel of the 1553 bus. Logic ground. Power supply return for the digital logic section. A01 I/O Address bit 1. A03 I/O Address bit 3. A05 I/O Address bit 5. A07 I/O Address bit 7. A09 I/O Address bit 9. A11 I/O Address bit 11. A13 I/O Address bit 13. A15 I/O See footnotes at end of table. Address bit 15 (MSB). STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93065 A REVISION LEVEL H SHEET 25 TABLE III. Pin functions - Continued. Terminal symbol I/O Description MEMOE/ADDR_LAT I/O Memory Output Enable/Address Latch. In transparent mode, used to enable data outputs for external RAM. In buffered mode, input used to configure the internal address buffers. MEMENA-OUT O Memory enable out. Logic 0 output enables external RAM. Used with MEMOE to read data or with MEMWR to write data into external RAM. CLOCK IN I Clock input. 16 MHz TTL clock. MEM/REG I Memory/register. Input from CPU to select memory or register data transfer. STRBD I Strobe data. Used in conjunction with SELECT to initiate a data transfer cycle to/from CPU. TRANSPARENT/ BUFFERED I Used to select between the transparent and buffered modes for the host processor interface. 1/ D11 I/O Data bus bit 11. D13 I/O Data bus bit 13. D15 I/O Data bus bit 15 (MSB). RTAD3 I Remote terminal address bit 3. RTAD2 I Remote terminal address bit 2. RTADP I Remote terminal address parity input. RD/WR I Read/write. Input from the CPU which defines the data bus transfer as a read or write operation. GNDA - Ground A. Power supply return connection for the A channel transceiver. -VA I Input power supply connection for the A channel transceiver. -15 V for device types 01, 03, 05, 07, 17, and 19 -12 V for device types 02, 04, 06, 08, 18, and 20. TX/RX-A I/O Transmit/receive transceiver-A. Input/output to the coupling transformer that connects to the A channel of the 1553 bus. D01 I/O Data bus bit 1. D03 I/O Data bus bit 3. D05 I/O Data bus bit 5. D07 I/O Data bus bit 7. D09 I/O See footnotes at end of table. Data bus bit 9. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93065 A REVISION LEVEL H SHEET 26 TABLE III. Pin functions - Continued. Terminal symbol +5 VB I/O I Description +5 V power supply connection for the B channel transceiver. TX/RX-B I/O Transmit/receive transceiver-B. Inverted input/output to coupling transformer that connects to channel B of the 1553 bus. A00 I/O Address bit 0 (LSB). A02 I/O Address bit 2. A04 I/O Address bit 4. A06 I/O Address bit 6. A08 I/O Address bit 8. A10 I/O Address bit 10. A12 I/O Address bit 12. A14 I/O Address bit 14. MEMWR/ZERO WAIT O/I Memory write. Output pulse to write data into memory. MEMENA-IN/ TRIGGER SEL I Memory enable input. Enables internal RAM only: connect directly to MEMENA-OUT INCMD 1/ O Input command. Indicates BC to RTU currently in message transfer sequence. MSTRCLR I Master clear. Power-on reset from CPU. INT O Interrupt. Interrupt pulse line to CPU. IOEN O Input/out enable. Output to enable external buffers/latches connecting the hybrid to the address/data bus. SELECT I Select. Input from the CPU. When active selects device for operation. READYD O Ready data. When active indicates data has been received from, or is available to, the CPU. +5 VA I +5 V power supply connection for the channel A transceiver. TX/RX-A I/O Transmit/receive transceiver-A. Inverted input/output to the coupling transformer that connects to the A channel of the 1553 bus. DTREQ/16/8 O/I Data Transfer Request or 16 Bit/8 Bit Transfer Mode Select. In transparent mode, active low output signal used to request access to the RAM interface bus (address, data, and control buses). In buffered mode, input signal used to select between the 16 bit data transfer mode (16/8 = Logic 1) and the 8 bit data transfer mode (16/8 = Logic 0). See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93065 A REVISION LEVEL H SHEET 27 TABLE III. Pin functions - Continued. Terminal symbol I/O Description SSFLAG/EXT_TRIG I Sub System Flag/External Trigger Input. In the Remote Terminal mode, if this input is asserted low, the subsystem flag bit will be set in the device's RT Status Word. In the Bus Controller mode if the external BC Start option is enabled (bit 7 of Configuration Register #1), a low to high transition on this input will issue a BC Start command, starting execution of the current BC frame. In the Monitor mode if the external trigger is enabled (bit 7 of Configuration Register #1), a low to high transition on this input will issue a monitor trigger. This input has no effect in RT mode. DTGRT/MSB/LSB I Data Transfer Grant or Most Significant Byte/Least Significant Byte. In transparent mode, active low input signal asserted, in response to the DTREQ output, to indicate that control of the RAM interface bus has been granted to the BU-65170/61580. In buffered mode, input signal used to indicate which byte is currently begin transferred (MSB or LSB). The logic sense of MSB/LSB is controlled by the POLARITY_SEL input. MSB/LSB is only used in the 8-bit buffered mode. O/I Data Transfer Acknowledge or Polarity Select. In transparent mode, active low output signal used to indicate acceptance of the RAM interface bus in response to a data transfer grant (DTGRT). In 16-bit buffered mode (TRANSPARENT/BUFFERED = LOGIC 0 AND 16/8 = LOGIC 1), input signal used to control the logic sense of the RD/WR signal. If POLARITY_SEL is connected to logic 1, RD/WR should be asserted high (logic 1) for a read operation and low (logic 0) for a write operation. If POLARITY_SEL is connected to logic 0, RD/WR should be asserted low (logic 0) for a read operation and high (logic 1) for a write operation. In 8-bit buffered mode (TRANSPARENT/BUFFERED = LOGIC 0 AND 16/8 = LOGIC 0), input signal used to control the logic sense of the MSB/LSB signal. If POLARITY_SEL is is connected to logic 0, MSB/LSB should be asserted low (logic 0) to indicate the transfer of the least significant byte and high (logic 1) to indicate the transfer of the most significant byte. If POLARITY_SEL is connected to logic 1, MSB/LSB should be asserted high (logic 1) to indicate the transfer of the least significant byte and low (logic 0) to indicate the transfer of the most significant byte. I Memory Enable Input or Trigger Select. In transparent mode, active low Chip Select (CS) input to the 4K X 16 of internal shared RAM. If only internal RAM is used connect directly to MEMENA-OUT. In buffered mode, input signal used to indicate the order in which byte pairs are transferred to or from the BU-65170/61580 by the host processor. This signal has no operation in the 16-bit buffered mode. In the 8-bit buffered mode, TRIGGER_SEL should be asserted high (logic 1) if the byte order for both read operations and write operations is MSB followed LSB. TRIGGER_SEL should be asserted low (logic 0) if the byte order for both read operations and write operations is LSB followed MSB. DTACK/POLARITY_SEL MEMENA-IN/ TRIGGER_SEL See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93065 A REVISION LEVEL H SHEET 28 TABLE III. Pin functions - Continued. Terminal symbol MEMWR/ZERO_WAIT I/O O/I Description Memory Write or Zero Wait State. In transparent mode, active low output signal asserted low during memory write transfers to strobe data into internal or external RAM (normally connected to the WR signal on external RAM chips). In buffered mode, input signal used to select between the zero wait state mode (ZEROWAIT = logic 0) and the non-zero wait state mode (ZEROWAIT = logic 1). RT_AD_LATCH 2/ I RT Address Latch. Input signal used to control the ACE internal RT Address Latch. A logic 0 configures the ACE to have a hardwired ( transparent ) RT address. A logic 1 configures the ACE to for the latched RT address mode. The value presented on the RTAD4, RTAD0, RTADP inputs is latched on the rising edge of RT_AD_LATCH. TX_INH_A, TX_INH_B 3/ I The 1553 Channel A and /or Channel B transmitters may be inhibited by asserting the respective TX_INH input(s) high. Note that the ACE will fail its BC off self-test if the respective TX_INH input is logic 1. 1/ 2/ 3/ Not applicable to device types 25, 26, 42, and 43. Applicable to device types 25, 26, 42, and 43. Applicable to device types 10, 12, 14, 16, 22, 24, 31, 33, 35, 37, 39, and 41. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 SIZE 5962-93065 A REVISION LEVEL H SHEET 29 STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 02-07-15 Approved sources of supply for SMD 5962-93095 are listed below for immediate acquisition information only and shall be added to MIL-HDBK-103 and QML-38534 during the next revisions. MIL-HDBK-103 and QML-38534 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DSCC-VA. This bulletin is superseded by the next dated revisions of MIL-HDBK-103 and QML-38534. Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-9306501HXA 5962-9306501HXA 5962-9306501HXA 5962-9306501HXA 5962-9306501HXA 5962-9306501HXA 5962-9306501HXA 5962-9306501HXA S7631 S7631 S7631 S7631 19645 19645 19645 19645 BU-65170S1-150 BU-65170BS1-150 BU-65170S1-140 BU-65170BS1-140 BU-65170S1-150 BU-65170BS1-150 BU-65170S1-140 BU-65170BS1-140 5962-9306501HXC 5962-9306501HXC 5962-9306501HXC 5962-9306501HXC 5962-9306501HXC 5962-9306501HXC 5962-9306501HXC 5962-9306501HXC S7631 S7631 S7631 S7631 19645 19645 19645 19645 BU-65170S1-130 BU-65170BS1-130 BU-65170S1-110 BU-65170BS1-110 BU-65170S1-130 BU-65170BS1-130 BU-65170S1-110 BU-65170BS1-110 5962-9306501HYA 5962-9306501HYA 5962-9306501HYA 5962-9306501HYA 5962-9306501HYA 5962-9306501HYA 5962-9306501HYA 5962-9306501HYA S7631 S7631 S7631 S7631 19645 19645 19645 19645 BU-65170V1-150 BU-65170BV1-150 BU-65170V1-140 BU-65170BV1-140 BU-65170V1-150 BU-65170BV1-150 BU-65170V1-140 BU-65170BV1-140 5962-9306501HYC 5962-9306501HYC 5962-9306501HYC 5962-9306501HYC 5962-9306501HYC 5962-9306501HYC 5962-9306501HYC 5962-9306501HYC S7631 S7631 S7631 S7631 19645 19645 19645 19645 BU-65170V1-130 BU-65170BV1-130 BU-65170V1-110 BU-65170BV1-110 BU-65170V1-130 BU-65170BV1-130 BU-65170V1-110 BU-65170BV1-110 19645 5962-9306501HZC 19645 5962-9306501HZC See footnotes at end of table. 1 of 22 BU-65170J1-130 BU-65170J1-110 STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued. DATE: 02-07-15 Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-9306502HXA 5962-9306502HXA 5962-9306502HXA 5962-9306502HXA 5962-9306502HXA 5962-9306502HXA 5962-9306502HXA 5962-9306502HXA S7631 S7631 S7631 S7631 19645 19645 19645 19645 BU-65170S2-150 BU-65170BS2-150 BU-65170S2-140 BU-65170BS2-140 BU-65170S2-150 BU-65170BS2-150 BU-65170S2-140 BU-65170BS2-140 5962-9306502HXC 5962-9306502HXC 5962-9306502HXC 5962-9306502HXC 5962-9306502HXC 5962-9306502HXC 5962-9306502HXC 5962-9306502HXC S7631 S7631 S7631 S7631 19645 19645 19645 19645 BU-65170S2-130 BU-65170BS2-130 BU-65170S2-110 BU-65170BS2-110 BU-65170S2-130 BU-65170BS2-130 BU-65170S2-110 BU-65170BS2-110 5962-9306502HYA 5962-9306502HYA 5962-9306502HYA 5962-9306502HYA 5962-9306502HYA 5962-9306502HYA 5962-9306502HYA 5962-9306502HYA S7631 S7631 S7631 S7631 19645 19645 19645 19645 BU-65170V2-150 BU-65170BV2-150 BU-65170V2-140 BU-65170BV2-140 BU-65170V2-150 BU-65170BV2-150 BU-65170V2-140 BU-65170BV2-140 5962-9306502HYC 5962-9306502HYC 5962-9306502HYC 5962-9306502HYC 5962-9306502HYC 5962-9306502HYC 5962-9306502HYC 5962-9306502HYC S7631 S7631 S7631 S7631 19645 19645 19645 19645 BU-65170V2-130 BU-65170BV2-130 BU-65170V2-110 BU-65170BV2-110 BU-65170V2-130 BU-65170BV2-130 BU-65170V2-110 BU-65170BV2-110 19645 5962-9306502HZC 19645 5962-9306502HZC See footnotes at end of table. 2 of 22 BU-65170J2-130 BU-65170J2-110 STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued. DATE: 02-07-15 Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-9306503HXA 5962-9306503HXA 5962-9306503HXA 5962-9306503HXA 5962-9306503HXA 5962-9306503HXA 5962-9306503HXA 5962-9306503HXA S7631 S7631 S7631 S7631 19645 19645 19645 19645 BU-61580S1-150 BU-61580BS1-150 BU-61580S1-140 BU-61580BS1-140 BU-61580S1-150 BU-61580BS1-150 BU-61580S1-140 BU-61580BS1-140 5962-9306503HXC 5962-9306503HXC 5962-9306503HXC 5962-9306503HXC 5962-9306503HXC 5962-9306503HXC 5962-9306503HXC 5962-9306503HXC S7631 S7631 S7631 S7631 19645 19645 19645 19645 BU-61580S1-130 BU-61580BS1-130 BU-61580S1-110 BU-61580BS1-110 BU-61580S1-130 BU-61580BS1-130 BU-61580S1-110 BU-61580BS1-110 5962-9306503HYA 5962-9306503HYA 5962-9306503HYA 5962-9306503HYA 5962-9306503HYA 5962-9306503HYA 5962-9306503HYA 5962-9306503HYA S7631 S7631 S7631 S7631 19645 19645 19645 19645 BU-61580V1-150 BU-61580BV1-150 BU-61580V1-140 BU-61580BV1-140 BU-61580V1-150 BU-61580BV1-150 BU-61580V1-140 BU-61580BV1-140 5962-9306503HYC 5962-9306503HYC 5962-9306503HYC 5962-9306503HYC 5962-9306503HYC 5962-9306503HYC 5962-9306503HYC 5962-9306503HYC S7631 S7631 S7631 S7631 19645 19645 19645 19645 BU-61580V1-130 BU-61580BV1-130 BU-61580V1-110 BU-61580BV1-110 BU-61580V1-130 BU-61580BV1-130 BU-61580V1-110 BU-61580BV1-110 19645 5962-9306503HZC 19645 5962-9306503HZC See footnotes at end of table. 3 of 22 BU-61580J1-130 BU-61580J1-110 STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued. DATE: 02-07-15 Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-9306504HXA 5962-9306504HXA 5962-9306504HXA 5962-9306504HXA 5962-9306504HXA 5962-9306504HXA 5962-9306504HXA 5962-9306504HXA S7631 S7631 S7631 S7631 19645 19645 19645 19645 BU-61580S2-150 BU-61580BS2-150 BU-61580S2-140 BU-61580BS2-140 BU-61580S2-150 BU-61580BS2-150 BU-61580S2-140 BU-61580BS2-140 5962-9306504HXC 5962-9306504HXC 5962-9306504HXC 5962-9306504HXC 5962-9306504HXC 5962-9306504HXC 5962-9306504HXC 5962-9306504HXC S7631 S7631 S7631 S7631 19645 19645 19645 19645 BU-61580S2-130 BU-61580BS2-130 BU-61580S2-110 BU-61580BS2-110 BU-61580S2-130 BU-61580BS2-130 BU-61580S2-110 BU-61580BS2-110 5962-9306504HYA 5962-9306504HYA 5962-9306504HYA 5962-9306504HYA 5962-9306504HYA 5962-9306504HYA 5962-9306504HYA 5962-9306504HYA S7631 S7631 S7631 S7631 19645 19645 19645 19645 BU-61580V2-150 BU-61580BV2-150 BU-61580V2-140 BU-61580BV2-140 BU-61580V2-150 BU-61580BV2-150 BU-61580V2-140 BU-61580BV2-140 5962-9306504HYC 5962-9306504HYC 5962-9306504HYC 5962-9306504HYC 5962-9306504HYC 5962-9306504HYC 5962-9306504HYC 5962-9306504HYC S7631 S7631 S7631 S7631 19645 19645 19645 19645 BU-61580V2-130 BU-61580BV2-130 BU-61580V2-110 BU-61580BV2-110 BU-61580V2-130 BU-61580BV2-130 BU-61580V2-110 BU-61580BV2-110 19645 5962-9306504HZC 19645 5962-9306504HZC See footnotes at end of table. 4 of 22 BU-61580J2-130 BU-61580J2-110 STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued. DATE: 02-07-15 Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-9306505HXA 5962-9306505HXA 5962-9306505HXA 5962-9306505HXA 5962-9306505HXA 5962-9306505HXA 5962-9306505HXA 5962-9306505HXA S7631 S7631 S7631 S7631 19645 19645 19645 19645 BU-65171S1-150 BU-65171BS1-150 BU-65171S1-140 BU-65171BS1-140 BU-65171S1-150 BU-65171BS1-150 BU-65171S1-140 BU-65171BS1-140 5962-9306505HXC 5962-9306505HXC 5962-9306505HXC 5962-9306505HXC 5962-9306505HXC 5962-9306505HXC 5962-9306505HXC 5962-9306505HXC S7631 S7631 S7631 S7631 19645 19645 19645 19645 BU-65171S1-130 BU-65171BS1-130 BU-65171S1-110 BU-65171BS1-110 BU-65171S1-130 BU-65171BS1-130 BU-65171S1-110 BU-65171BS1-110 5962-9306505HYA 5962-9306505HYA 5962-9306505HYA 5962-9306505HYA 5962-9306505HYA 5962-9306505HYA 5962-9306505HYA 5962-9306505HYA S7631 S7631 S7631 S7631 19645 19645 19645 19645 BU-65171V1-150 BU-65171BV1-150 BU-65171V1-140 BU-65171BV1-140 BU-65171V1-150 BU-65171BV1-150 BU-65171V1-140 BU-65171BV1-140 5962-9306505HYC 5962-9306505HYC 5962-9306505HYC 5962-9306505HYC 5962-9306505HYC 5962-9306505HYC 5962-9306505HYC 5962-9306505HYC S7631 S7631 S7631 S7631 19645 19645 19645 19645 BU-65171V1-130 BU-65171BV1-130 BU-65171V1-110 BU-65171BV1-110 BU-65171V1-130 BU-65171BV1-130 BU-65171V1-110 BU-65171BV1-110 19645 5962-9306505HZC 19645 5962-9306505HZC See footnotes at end of table. 5 of 22 BU-65171J1-130 BU-65171J1-110 STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued. DATE: 02-07-15 Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-9306506HXA 5962-9306506HXA 5962-9306506HXA 5962-9306506HXA 5962-9306506HXA 5962-9306506HXA 5962-9306506HXA 5962-9306506HXA S7631 S7631 S7631 S7631 19645 19645 19645 19645 BU-65171S2-150 BU-65171BS2-150 BU-65171S2-140 BU-65171BS2-140 BU-65171S2-150 BU-65171BS2-150 BU-65171S2-140 BU-65171BS2-140 5962-9306506HXC 5962-9306506HXC 5962-9306506HXC 5962-9306506HXC 5962-9306506HXC 5962-9306506HXC 5962-9306506HXC 5962-9306506HXC S7631 S7631 S7631 S7631 19645 19645 19645 19645 BU-65171S2-130 BU-65171BS2-130 BU-65171S2-110 BU-65171BS2-110 BU-65171S2-130 BU-65171BS2-130 BU-65171S2-110 BU-65171BS2-110 5962-9306506HYA 5962-9306506HYA 5962-9306506HYA 5962-9306506HYA 5962-9306506HYA 5962-9306506HYA 5962-9306506HYA 5962-9306506HYA S7631 S7631 S7631 S7631 19645 19645 19645 19645 BU-65171V2-150 BU-65171BV2-150 BU-65171V2-140 BU-65171BV2-140 BU-65171V2-150 BU-65171BV2-150 BU-65171V2-140 BU-65171BV2-140 5962-9306506HYC 5962-9306506HYC 5962-9306506HYC 5962-9306506HYC 5962-9306506HYC 5962-9306506HYC 5962-9306506HYC 5962-9306506HYC S7631 S7631 S7631 S7631 19645 19645 19645 19645 BU-65171V2-130 BU-65171BV2-130 BU-65171V2-110 BU-65171BV2-110 BU-65171V2-130 BU-65171BV2-130 BU-65171V2-110 BU-65171BV2-110 19645 5962-9306506HZC 19645 5962-9306506HZC See footnotes at end of table. 6 of 22 BU-65171J2-130 BU-65171J2-110 STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued. DATE: 02-07-15 Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-9306507HXA 5962-9306507HXA 5962-9306507HXA 5962-9306507HXA 5962-9306507HXA 5962-9306507HXA 5962-9306507HXA 5962-9306507HXA S7631 S7631 S7631 S7631 19645 19645 19645 19645 BU-61581S1-150 BU-61581BS1-150 BU-61581S1-140 BU-61581BS1-140 BU-61581S1-150 BU-61581BS1-150 BU-61581S1-140 BU-61581BS1-140 5962-9306507HXC 5962-9306507HXC 5962-9306507HXC 5962-9306507HXC 5962-9306507HXC 5962-9306507HXC 5962-9306507HXC 5962-9306507HXC S7631 S7631 S7631 S7631 19645 19645 19645 19645 BU-61581S1-130 BU-61581BS1-130 BU-61581S1-110 BU-61581BS1-110 BU-61581S1-130 BU-61581BS1-130 BU-61581S1-110 BU-61581BS1-110 5962-9306507HYA 5962-9306507HYA 5962-9306507HYA 5962-9306507HYA 5962-9306507HYA 5962-9306507HYA 5962-9306507HYA 5962-9306507HYA S7631 S7631 S7631 S7631 19645 19645 19645 19645 BU-61581V1-150 BU-61581BV1-150 BU-61581V1-140 BU-61581BV1-140 BU-61581V1-150 BU-61581BV1-150 BU-61581V1-140 BU-61581BV1-140 5962-9306507HYC 5962-9306507HYC 5962-9306507HYC 5962-9306507HYC 5962-9306507HYC 5962-9306507HYC 5962-9306507HYC 5962-9306507HYC S7631 S7631 S7631 S7631 19645 19645 19645 19645 BU-61581V1-130 BU-61581BV1-130 BU-61581V1-110 BU-61581BV1-110 BU-61581V1-130 BU-61581BV1-130 BU-61581V1-110 BU-61581BV1-110 19645 5962-9306507HZC 19645 5962-9306507HZC See footnotes at end of table. 7 of 22 BU-61581J1-130 BU-61581J1-110 STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued. DATE: 02-07-15 Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-9306508HXA 5962-9306508HXA 5962-9306508HXA 5962-9306508HXA 5962-9306508HXA 5962-9306508HXA 5962-9306508HXA 5962-9306508HXA S7631 S7631 S7631 S7631 19645 19645 19645 19645 BU-61581S2-150 BU-61581BS2-150 BU-61581S2-140 BU-61581BS2-140 BU-61581S2-150 BU-61581BS2-150 BU-61581S2-140 BU-61581BS2-140 5962-9306508HXC 5962-9306508HXC 5962-9306508HXC 5962-9306508HXC 5962-9306508HXC 5962-9306508HXC 5962-9306508HXC 5962-9306508HXC S7631 S7631 S7631 S7631 19645 19645 19645 19645 BU-61581S2-130 BU-61581BS2-130 BU-61581S2-110 BU-61581BS2-110 BU-61581S2-130 BU-61581BS2-130 BU-61581S2-110 BU-61581BS2-110 5962-9306508HYA 5962-9306508HYA 5962-9306508HYA 5962-9306508HYA 5962-9306508HYA 5962-9306508HYA 5962-9306508HYA 5962-9306508HYA S7631 S7631 S7631 S7631 19645 19645 19645 19645 BU-61581V2-150 BU-61581BV2-150 BU-61581V2-140 BU-61581BV2-140 BU-61581V2-150 BU-61581BV2-150 BU-61581V2-140 BU-61581BV2-140 5962-9306508HYC 5962-9306508HYC 5962-9306508HYC 5962-9306508HYC 5962-9306508HYC 5962-9306508HYC 5962-9306508HYC 5962-9306508HYC S7631 S7631 S7631 S7631 19645 19645 19645 19645 BU-61581V2-130 BU-61581BV2-130 BU-61581V2-110 BU-61581BV2-110 BU-61581V2-130 BU-61581BV2-130 BU-61581V2-110 BU-61581BV2-110 19645 5962-9306508HZC 19645 5962-9306508HZC See footnotes at end of table. 8 of 22 BU-61581J2-130 BU-61581J2-110 STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued. DATE: 02-07-15 Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-9306509HXA 5962-9306509HXC 5962-9306509HYA 5962-9306509HYC 3/ 3/ 3/ 3/ BU-65170CS3-140 BU-65170CS3-110 BU-65170CV3-140 BU-65170CV3-110 5962-9306510HXA 5962-9306510HXC 5962-9306510HYA 5962-9306510HYC 3/ 3/ 3/ 3/ BU-65170CS6-140 BU-65170CS6-110 BU-65170CV6-140 BU-65170CV6-110 5962-9306511HXA 5962-9306511HXC 5962-9306511HYA 5962-9306511HYC 3/ 3/ 3/ 3/ BU-61580CS3-140 BU-61580CS3-110 BU-61580CV3-140 BU-61580CV3-110 5962-9306512HXA 5962-9306512HXC 5962-9306512HYA 5962-9306512HYC 3/ 3/ 3/ 3/ BU-61580CS6-140 BU-61580CS6-110 BU-61580CV6-140 BU-61580CV6-110 5962-9306513HXA 5962-9306513HXC 5962-9306513HYA 5962-9306513HYC 3/ 3/ 3/ 3/ BU-65171CS3-140 BU-65171CS3-110 BU-65171CV3-140 BU-65171CV3-110 5962-9306514HXA 5962-9306514HXC 5962-9306514HYA 5962-9306514HYC 3/ 3/ 3/ 3/ BU-65171CS6-140 BU-65171CS6-110 BU-65171CV6-140 BU-65171CV6-110 5962-9306515HXA 5962-9306515HXC 5962-9306515HYA 5962-9306515HYC 3/ 3/ 3/ 3/ BU-61581CS3-140 BU-61581CS3-110 BU-61581CV3-140 BU-61581CV3-110 5962-9306516HXA 3/ 5962-9306516HXC 3/ 5962-9306516HYA 3/ 3/ 5962-9306516HYC See footnotes at end of table. BU-61581CS6-140 BU-61581CS6-110 BU-61581CV6-140 BU-61581CV6-110 9 of 22 STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued. DATE: 02-07-15 Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-9306517HXA 5962-9306517HXA 5962-9306517HXA 5962-9306517HXA S7631 S7631 19645 19645 BU-61585S1-150 BU-61585S1-140 BU-61585S1-150 BU-61585S1-140 5962-9306517HXC 5962-9306517HXC 5962-9306517HXC 5962-9306517HXC S7631 S7631 19645 19645 BU-61585S1-130 BU-61585S1-110 BU-61585S1-130 BU-61585S1-110 5962-9306517HYA 5962-9306517HYA 5962-9306517HYA 5962-9306517HYA S7631 S7631 19645 19645 BU-61585V1-150 BU-61585V1-140 BU-61585V1-150 BU-61585V1-140 5962-9306517HYC 5962-9306517HYC 5962-9306517HYC 5962-9306517HYC S7631 S7631 19645 19645 BU-61585V1-130 BU-61585V1-110 BU-61585V1-130 BU-61585V1-110 5962-9306517HZA 5962-9306517HZC 3/ 3/ BU-61585J1-140 BU-61585J1-110 5962-9306518HXA 5962-9306518HXA 5962-9306518HXA 5962-9306518HXA S7631 S7631 19645 19645 BU-61585S2-150 BU-61585S2-140 BU-61585S2-150 BU-61585S2-140 5962-9306518HXC 5962-9306518HXC 5962-9306518HXC 5962-9306518HXC S7631 S7631 19645 19645 BU-61585S2-130 BU-61585S2-110 BU-61585S2-130 BU-61585S2-110 5962-9306518HYA 5962-9306518HYA 5962-9306518HYA 5962-9306518HYA S7631 S7631 19645 19645 BU-61585V2-150 BU-61585V2-140 BU-61585V2-150 BU-61585V2-140 5962-9306518HYC 5962-9306518HYC 5962-9306518HYC 5962-9306518HYC S7631 S7631 19645 19645 BU-61585V2-130 BU-61585V2-110 BU-61585V2-130 BU-61585V2-110 5962-9306518HZA 5962-9306518HZC 3/ 3/ BU-61585J2-140 BU-61585J2-110 See footnotes at end of table. 10 of 22 STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued. DATE: 02-07-15 Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-9306519HXA 5962-9306519HXA 5962-9306519HXA 5962-9306519HXA S7631 S7631 19645 19645 BU-61586S1-150 BU-61586S1-140 BU-61586S1-150 BU-61586S1-140 5962-9306519HXC 5962-9306519HXC 5962-9306519HXC 5962-9306519HXC S7631 S7631 19645 19645 BU-61586S1-130 BU-61586S1-110 BU-61586S1-130 BU-61586S1-110 5962-9306519HYA 5962-9306519HYA 5962-9306519HYA 5962-9306519HYA S7631 S7631 19645 19645 BU-61586V1-150 BU-61586V1-140 BU-61586V1-150 BU-61586V1-140 5962-9306519HYC 5962-9306519HYC 5962-9306519HYC 5962-9306519HYC S7631 S7631 19645 19645 BU-61586V1-130 BU-61586V1-110 BU-61586V1-130 BU-61586V1-110 5962-9306519HZA 5962-9306519HZC 3/ 3/ BU-61586J1-140 BU-61586J1-110 5962-9306520HXA 5962-9306520HXA 5962-9306520HXA 5962-9306520HXA S7631 S7631 19645 19645 BU-61586S2-150 BU-61586S2-140 BU-61586S2-150 BU-61586S2-140 5962-9306520HXC 5962-9306520HXC 5962-9306520HXC 5962-9306520HXC S7631 S7631 19645 19645 BU-61586S2-130 BU-61586S2-110 BU-61586S2-130 BU-61586S2-110 5962-9306520HYA 5962-9306520HYA 5962-9306520HYA 5962-9306520HYA S7631 S7631 19645 19645 BU-61586V2-150 BU-61586V2-140 BU-61586V2-150 BU-61586V2-140 5962-9306520HYC 5962-9306520HYC 5962-9306520HYC 5962-9306520HYC S7631 S7631 19645 19645 BU-61586V2-130 BU-61586V2-110 BU-61586V2-130 BU-61586V2-110 5962-9306520HZA 5962-9306520HZC 3/ 3/ BU-61586J2-140 BU-61586J2-110 See footnotes at end of table. 11 of 22 STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued. DATE: 02-07-15 Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-9306521HNA 5962-9306521HNA 5962-9306521HNC 5962-9306521HNC 5962-9306521HXA 5962-9306521HXA 5962-9306521HXC 5962-9306521HXC 5962-9306521HYA 5962-9306521HYA 5962-9306521HYC 5962-9306521HYC 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ BU-61585BG3-150 BU-61585BG3-140 BU-61585BG3-130 BU-61585BG3-110 BU-61585BS3-150 BU-61585BS3-140 BU-61585BS3-130 BU-61585BS3-110 BU-61585BV3-150 BU-61585BV3-140 BU-61585BV3-130 BU-61585BV3-110 5962-9306522HNA 5962-9306522HNA 5962-9306522HNC 5962-9306522HNC 5962-9306522HXA 5962-9306522HXA 5962-9306522HXC 5962-9306522HXC 5962-9306522HYA 5962-9306522HYA 5962-9306522HYC 5962-9306522HYC 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ BU-61585BG6-150 BU-61585BG6-140 BU-61585BG6-130 BU-61585BG6-110 BU-61585BS6-150 BU-61585BS6-140 BU-61585BS6-130 BU-61585BS6-110 BU-61585BV6-150 BU-61585BV6-140 BU-61585BV6-130 BU-61585BV6-110 5962-9306523HNA 5962-9306523HNA 5962-9306523HNC 5962-9306523HNC 5962-9306523HXA 5962-9306523HXA 5962-9306523HXC 5962-9306523HXC 5962-9306523HYA 5962-9306523HYA 5962-9306523HYC 5962-9396523HYC 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ BU-61586BG3-150 BU-61586BG3-140 BU-61586BG3-130 BU-61585BG3-110 BU-61586BS3-150 BU-61586BS3-140 BU-61586BS3-130 BU-61586BS3-110 BU-61586BV3-150 BU-61586BV3-140 BU-61586BV3-130 BU-61586BV3-110 5962-9306524HNA 5962-9306524HNA 5962-9306524HNC 5962-9306524HNC 5962-9306524HXA 5962-9306524HXA 5962-9306524HXC 5962-9306524HXC 5962-9306524HYA 5962-9306524HYA 5962-9306524HYC 5962-9306524HYC 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ BU-61586BG6-150 BU-61586BG6-140 BU-61586BG6-130 BU-61586BG6-110 BU-61586BS6-150 BU-61586BS6-140 BU-61586BS6-130 BU-61586BS6-110 BU-61586BV6-150 BU-61586BV6-140 BU-61586BV6-130 BU-61586BV6-110 See footnotes at end of table. 12 of 22 STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued. DATE: 02-07-15 Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-9306525HMA 5962-9306525HMA 5962-9306525HMC 5962-9306525HMC 5962-9306525HTA 5962-9306525HTA 5962-9306525HTC 5962-9306525HTC 5962-9306525HUA 5962-9306525HUA 5962-9306525HUC 5962-9306525HUC 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ BU-61588BG3-150 BU-61588BG3-140 BU-61588BG3-130 BU-61588BG3-110 BU-61588BF3-150 BU-61588BF3-140 BU-61588BF3-130 BU-61588BF3-110 BU-61588BP3-150 BU-61588BP3-140 BU-61588BP3-130 BU-61588BP3-110 5962-9306526HMA 5962-9306526HMA 5962-9306526HMC 5962-9306526HMC 5962-9306526HTA 5962-9306526HTA 5962-9306526HTC 5962-9306526HTC 5962-9306526HUA 5962-9306526HUA 5962-9306526HUC 5962-9306526HUC 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ 3/ BU-65178BG3-150 BU-65178BG3-140 BU-65178BG3-130 BU-65178BG3-110 BU-65178BF3-150 BU-65178BF3-140 BU-65178BF3-130 BU-65178BF3-110 BU-65178BP3-150 BU-65178BP3-140 BU-65178BP3-130 BU-65178BP3-110 5962-9306527HMA 5962-9306527HMC 5962-9306527HTA 5962-9306527HTC 5962-9306527HUA 5962-9306527HUC 3/ 3/ 3/ 3/ 3/ 3/ BU-65179BG3-140 BU-65179BG3-110 BU-65179BF3-140 BU-65179BF3-110 BU-65179BP3-140 BU-65179BP3-110 5962-9306528HMA 5962-9306528HMC 5962-9306528HTA 5962-9306528HTC 5962-9306528HUA 5962-9306528HUC 3/ 3/ 3/ 3/ 3/ 3/ BU-61688AG3-140 BU-61688AG3-110 BU-61688AF3-140 BU-61688AF3-110 BU-61688AP3-140 BU-61688AP3-110 5962-9306529HMA 5962-9306529HMC 5962-9306529HTA 5962-9306529HTC 5962-9306529HUA 5962-9306529HUC 3/ 3/ 3/ 3/ 3/ 3/ BU-61689AG3-140 BU-61689AG3-110 BU-61689AF3-140 BU-61689AF3-110 BU-61689AP3-140 BU-61689AP3-110 See footnotes at end of table. 13 of 22 STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued. DATE: 02-07-15 Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-9306530HNA 5962-9306530HNA 5962-9306530HNA 5962-9306530HNA S7631 S7631 19645 19645 BU-65170DG3-150 BU-65170DG3-140 BU-65170DG3-150 BU-65170DG3-140 5962-9306530HNC 5962-9306530HNC 5962-9306530HNC 5962-9306530HNC S7631 S7631 19645 19645 BU-65170DG3-130 BU-65170DG3-110 BU-65170DG3-130 BU-65170DG3-110 5962-9306530HXA 5962-9306530HXA 5962-9306530HXA 5962-9306530HXA S7631 S7631 19645 19645 BU-65170DS3-150 BU-65170DS3-140 BU-65170DS3-150 BU-65170DS3-140 5962-9306530HXC 5962-9306530HXC 5962-9306530HXC 5962-9306530HXC S7631 S7631 19645 19645 BU-65170DS3-130 BU-65170DS3-110 BU-65170DS3-130 BU-65170DS3-110 5962-9306530HYA 5962-9306530HYA 5962-9306530HYA 5962-9306530HYA S7631 S7631 19645 19645 BU-65170DV3-150 BU-65170DV3-140 BU-65170DV3-150 BU-65170DV3-140 5962-9306530HYC 5962-9306530HYC 5962-9306530HYC 5962-9306530HYC S7631 S7631 19645 19645 BU-65170DV3-130 BU-65170DV3-110 BU-65170DV3-130 BU-65170DV3-110 5962-9306531HNA 5962-9306531HNA 5962-9306531HNA 5962-9306531HNA S7631 S7631 19645 19645 BU-65170DG6-150 BU-65170DG6-140 BU-65170DG6-150 BU-65170DG6-140 5962-9306531HNC 5962-9306531HNC 5962-9306531HNC 5962-9306531HNC S7631 S7631 19645 19645 BU-65170DG6-130 BU-65170DG6-110 BU-65170DG6-130 BU-65170DG6-110 5962-9306531HXA 5962-9306531HXA 5962-9306531HXA 5962-9306531HXA S7631 S7631 19645 19645 BU-65170DS6-150 BU-65170DS6-140 BU-65170DS6-150 BU-65170DS6-140 5962-9306531HXC 5962-9306531HXC 5962-9306531HXC 5962-9306531HXC S7631 S7631 19645 19645 BU-65170DS6-130 BU-65170DS6-110 BU-65170DS6-130 BU-65170DS6-110 5962-9306531HYA 5962-9306531HYA 5962-9306531HYA 5962-9306531HYA S7631 S7631 19645 19645 BU-65170DV6-150 BU-65170DV6-140 BU-65170DV6-150 BU-65170DV6-140 5962-9306531HYC S7631 5962-9306531HYC S7631 5962-9306531HYC 19645 5962-9306531HYC 19645 See footnotes at end of table. BU-65170DV6-130 BU-65170DV6-110 BU-65170DV6-130 BU-65170DV6-110 14 of 22 STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued. DATE: 02-07-15 Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-9306532HNA 5962-9306532HNA 5962-9306532HNA 5962-9306532HNA S7631 S7631 19645 19645 BU-61580DG3-150 BU-61580DG3-140 BU-61580DG3-150 BU-61580DG3-140 5962-9306532HNC 5962-9306532HNC 5962-9306532HNC 5962-9306532HNC S7631 S7631 19645 19645 BU-61580DG3-130 BU-61580DG3-110 BU-61580DG3-130 BU-61580DG3-110 5962-9306532HXA 5962-9306532HXA 5962-9306532HXA 5962-9306532HXA S7631 S7631 19645 19645 BU-61580DS3-150 BU-61580DS3-140 BU-61580DS3-150 BU-61580DS3-140 5962-9306532HXC 5962-9306532HXC 5962-9306532HXC 5962-9306532HXC S7631 S7631 19645 19645 BU-61580DS3-130 BU-61580DS3-110 BU-61580DS3-130 BU-61580DS3-110 5962-9306532HYA 5962-9306532HYA 5962-9306532HYA 5962-9306532HYA S7631 S7631 19645 19645 BU-61580DV3-150 BU-61580DV3-140 BU-61580DV3-150 BU-61580DV3-140 5962-9306532HYC 5962-9306532HYC 5962-9306532HYC 5962-9306532HYC S7631 S7631 19645 19645 BU-61580DV3-130 BU-61580DV3-110 BU-61580DV3-130 BU-61580DV3-110 5962-9306533HNA 5962-9306533HNA 5962-9306533HNA 5962-9306533HNA S7631 S7631 19645 19645 BU-61580DG6-150 BU-61580DG6-140 BU-61580DG6-150 BU-61580DG6-140 5962-9306533HNC 5962-9306533HNC 5962-9306533HNC 5962-9306533HNC S7631 S7631 19645 19645 BU-61580DG6-130 BU-61580DG6-110 BU-61580DG6-130 BU-61580DG6-110 5962-9306533HXA 5962-9306533HXA 5962-9306533HXA 5962-9306533HXA S7631 S7631 19645 19645 BU-61580DS6-150 BU-61580DS6-140 BU-61580DS6-150 BU-61580DS6-140 5962-9306533HXC 5962-9306533HXC 5962-9306533HXC 5962-9306533HXC S7631 S7631 19645 19645 BU-61580DS6-130 BU-61580DS6-110 BU-61580DS6-130 BU-61580DS6-110 5962-9306533HYA 5962-9306533HYA 5962-9306533HYA 5962-9306533HYA S7631 S7631 19645 19645 BU-61580DV6-150 BU-61580DV6-140 BU-61580DV6-150 BU-61580DV6-140 5962-9306533HYC S7631 5962-9306533HYC S7631 5962-9306533HYC 19645 5962-9306533HYC 19645 See footnotes at end of table. BU-61580DV6-130 BU-61580DV6-110 BU-61580DV6-130 BU-61580DV6-110 15 of 22 STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued. DATE: 02-07-15 Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-9306534HNA 5962-9306534HNA 5962-9306534HNA 5962-9306534HNA S7631 S7631 19645 19645 BU-65171DG3-150 BU-65171DG3-140 BU-65171DG3-150 BU-65171DG3-140 5962-9306534HNC 5962-9306534HNC 5962-9306534HNC 5962-9306534HNC S7631 S7631 19645 19645 BU-65171DG3-130 BU-65171DG3-110 BU-65171DG3-130 BU-65171DG3-110 5962-9306534HXA 5962-9306534HXA 5962-9306534HXA 5962-9306534HXA S7631 S7631 19645 19645 BU-65171DS3-150 BU-65171DS3-140 BU-65171DS3-150 BU-65171DS3-140 5962-9306534HXC 5962-9306534HXC 5962-9306534HXC 5962-9306534HXC S7631 S7631 19645 19645 BU-65171DS3-130 BU-65171DS3-110 BU-65171DS3-130 BU-65171DS3-110 5962-9306534HYA 5962-9306534HYA 5962-9306534HYA 5962-9306534HYA S7631 S7631 19645 19645 BU-65171DV3-150 BU-65171DV3-140 BU-65171DV3-150 BU-65171DV3-140 5962-9306534HYC 5962-9306534HYC 5962-9306534HYC 5962-9306534HYC S7631 S7631 19645 19645 BU-65171DV3-130 BU-65171DV3-110 BU-65171DV3-130 BU-65171DV3-110 5962-9306535HNA 5962-9306535HNA 5962-9306535HNA 5962-9306535HNA S7631 S7631 19645 19645 BU-65171DG6-150 BU-65171DG6-140 BU-65171DG6-150 BU-65171DG6-140 5962-9306535HNC 5962-9306535HNC 5962-9306535HNC 5962-9306535HNC S7631 S7631 19645 19645 BU-65171DG6-130 BU-65171DG6-110 BU-65171DG6-130 BU-65171DG6-110 5962-9306535HXA 5962-9306535HXA 5962-9306535HXA 5962-9306535HXA S7631 S7631 19645 19645 BU-65171DS6-150 BU-65171DS6-140 BU-65171DS6-150 BU-65171DS6-140 5962-9306535HXC 5962-9306535HXC 5962-9306535HXC 5962-9306535HXC S7631 S7631 19645 19645 BU-65171DS6-130 BU-65171DS6-110 BU-65171DS6-130 BU-65171DS6-110 5962-9306535HYA 5962-9306535HYA 5962-9306535HYA 5962-9306535HYA S7631 S7631 19645 19645 BU-65171DV6-150 BU-65171DV6-140 BU-65171DV6-150 BU-65171DV6-140 5962-9306535HYC S7631 5962-9306535HYC S7631 5962-9306535HYC 19645 5962-9306535HYC 19645 See footnotes at end of table. BU-65171DV6-130 BU-65171DV6-110 BU-65171DV6-130 BU-65171DV6-110 16 of 22 STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued. DATE: 02-07-15 Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-9306536HNA 5962-9306536HNA 5962-9306536HNA 5962-9306536HNA S7631 S7631 19645 19645 BU-61581DG3-150 BU-61581DG3-140 BU-61581DG3-150 BU-61581DG3-140 5962-9306536HNC 5962-9306536HNC 5962-9306536HNC 5962-9306536HNC S7631 S7631 19645 19645 BU-61581DG3-130 BU-61581DG3-110 BU-61581DG3-130 BU-61581DG3-110 5962-9306536HXA 5962-9306536HXA 5962-9306536HXA 5962-9306536HXA S7631 S7631 19645 19645 BU-61581DS3-150 BU-61581DS3-140 BU-61581DS3-150 BU-61581DS3-140 5962-9306536HXC 5962-9306536HXC 5962-9306536HXC 5962-9306536HXC S7631 S7631 19645 19645 BU-61581DS3-130 BU-61581DS3-110 BU-61581DS3-130 BU-61581DS3-110 5962-9306536HYA 5962-9306536HYA 5962-9306536HYA 5962-9306536HYA S7631 S7631 19645 19645 BU-61581DV3-150 BU-61581DV3-140 BU-61581DV3-150 BU-61581DV3-140 5962-9306536HYC 5962-9306536HYC 5962-9306536HYC 5962-9306536HYC S7631 S7631 19645 19645 BU-61581DV3-130 BU-61581DV3-110 BU-61581DV3-130 BU-61581DV3-110 5962-9306537HNA 5962-9306537HNA 5962-9306537HNA 5962-9306537HNA S7631 S7631 19645 19645 BU-61581DG6-150 BU-61581DG6-140 BU-61581DG6-150 BU-61581DG6-140 5962-9306537HNC 5962-9306537HNC 5962-9306537HNC 5962-9306537HNC S7631 S7631 19645 19645 BU-61581DG6-130 BU-61581DG6-110 BU-61581DG6-130 BU-61581DG6-110 5962-9306537HXA 5962-9306537HXA 5962-9306537HXA 5962-9306537HXA S7631 S7631 19645 19645 BU-61581DS6-150 BU-61581DS6-140 BU-61581DS6-150 BU-61581DS6-140 5962-9306537HXC 5962-9306537HXC 5962-9306537HXC 5962-9306537HXC S7631 S7631 19645 19645 BU-61581DS6-130 BU-61581DS6-110 BU-61581DS6-130 BU-61581DS6-110 5962-9306537HYA 5962-9306537HYA 5962-9306537HYA 5962-9306537HYA S7631 S7631 19645 19645 BU-61581DV6-150 BU-61581DV6-140 BU-61581DV6-150 BU-61581DV6-140 5962-9306537HYC S7631 5962-9306537HYC S7631 5962-9306537HYC 19645 5962-9306537HYC 19645 See footnotes at end of table. BU-61581DV6-130 BU-61581DV6-110 BU-61581DV6-130 BU-61581DV6-110 17 of 22 STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued. DATE: 02-07-15 Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-9306538HNA 5962-9306538HNA 5962-9306538HNA 5962-9306538HNA S7631 S7631 19645 19645 BU-61585DG3-150 BU-61585DG3-140 BU-61585DG3-150 BU-61585DG3-140 5962-9306538HNC 5962-9306538HNC 5962-9306538HNC 5962-9306538HNC S7631 S7631 19645 19645 BU-61585DG3-130 BU-61585DG3-110 BU-61585DG3-130 BU-61585DG3-110 5962-9306538HXA 5962-9306538HXA 5962-9306538HXA 5962-9306538HXA S7631 S7631 19645 19645 BU-61585DS3-150 BU-61585DS3-140 BU-61585DS3-150 BU-61585DS3-140 5962-9306538HXC 5962-9306538HXC 5962-9306538HXC 5962-9306538HXC S7631 S7631 19645 19645 BU-61585DS3-130 BU-61585DS3-110 BU-61585DS3-130 BU-61585DS3-110 5962-9306538HYA 5962-9306538HYA 5962-9306538HYA 5962-9306538HYA S7631 S7631 19645 19645 BU-61585DV3-150 BU-61585DV3-140 BU-61585DV3-150 BU-61585DV3-140 5962-9306538HYC 5962-9306538HYC 5962-9306538HYC 5962-9306538HYC S7631 S7631 19645 19645 BU-61585DV3-130 BU-61585DV3-110 BU-61585DV3-130 BU-61585DV3-110 5962-9306539HNA 5962-9306539HNA 5962-9306539HNA 5962-9306539HNA S7631 S7631 19645 19645 BU-61585DG6-150 BU-61585DG6-140 BU-61585DG6-150 BU-61585DG6-140 5962-9306539HNC 5962-9306539HNC 5962-9306539HNC 5962-9306539HNC S7631 S7631 19645 19645 BU-61585DG6-130 BU-61585DG6-110 BU-61585DG6-130 BU-61585DG6-110 5962-9306539HXA 5962-9306539HXA 5962-9306539HXA 5962-9306539HXA S7631 S7631 19645 19645 BU-61585DS6-150 BU-61585DS6-140 BU-61585DS6-150 BU-61585DS6-140 5962-9306539HXC 5962-9306539HXC 5962-9306539HXC 5962-9306539HXC S7631 S7631 19645 19645 BU-61585DS6-130 BU-61585DS6-110 BU-61585DS6-130 BU-61585DS6-110 5962-9306539HYA 5962-9306539HYA 5962-9306539HYA 5962-9306539HYA S7631 S7631 19645 19645 BU-61585DV6-150 BU-61585DV6-140 BU-61585DV6-150 BU-61585DV6-140 5962-9306539HYC S7631 5962-9306539HYC S7631 5962-9306539HYC 19645 5962-9306539HYC 19645 See footnotes at end of table. BU-61581DV6-130 BU-61581DV6-110 BU-61581DV6-130 BU-61581DV6-110 18 of 22 STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued. DATE: 02-07-15 Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-9306540HNA 5962-9306540HNA 5962-9306540HNA 5962-9306540HNA S7631 S7631 19645 19645 BU-61586DG3-150 BU-61586DG3-140 BU-61586DG3-150 BU-61586DG3-140 5962-9306540HNC 5962-9306540HNC 5962-9306540HNC 5962-9306540HNC S7631 S7631 19645 19645 BU-61586DG3-130 BU-61586DG3-110 BU-61586DG3-130 BU-61586DG3-110 5962-9306540HXA 5962-9306540HXA 5962-9306540HXA 5962-9306540HXA S7631 S7631 19645 19645 BU-61586DS3-150 BU-61586DS3-140 BU-61586DS3-150 BU-61586DS3-140 5962-9306540HXC 5962-9306540HXC 5962-9306540HXC 5962-9306540HXC S7631 S7631 19645 19645 BU-61586DS3-130 BU-61586DS3-110 BU-61586DS3-130 BU-61586DS3-110 5962-9306540HYA 5962-9306540HYA 5962-9306540HYA 5962-9306540HYA S7631 S7631 19645 19645 BU-61586DV3-150 BU-61586DV3-140 BU-61586DV3-150 BU-61586DV3-140 5962-9306540HYC 5962-9306540HYC 5962-9306540HYC 5962-9306540HYC S7631 S7631 19645 19645 BU-61586DV3-130 BU-61586DV3-110 BU-61586DV3-130 BU-61586DV3-110 5962-9306541HNA 5962-9306541HNA 5962-9306541HNA 5962-9306541HNA S7631 S7631 19645 19645 BU-61586DG6-150 BU-61586DG6-140 BU-61586DG6-150 BU-61586DG6-140 5962-9306541HNC 5962-9306541HNC 5962-9306541HNC 5962-9306541HNC S7631 S7631 19645 19645 BU-61586DG6-130 BU-61586DG6-110 BU-61586DG6-130 BU-61586DG6-110 5962-9306541HXA 5962-9306541HXA 5962-9306541HXA 5962-9306541HXA S7631 S7631 19645 19645 BU-61586DS6-150 BU-61586DS6-140 BU-61586DS6-150 BU-61586DS6-140 5962-9306541HXC 5962-9306541HXC 5962-9306541HXC 5962-9306541HXC S7631 S7631 19645 19645 BU-61586DS6-130 BU-61586DS6-110 BU-61586DS6-130 BU-61586DS6-110 5962-9306541HYA 5962-9306541HYA 5962-9306541HYA 5962-9306541HYA S7631 S7631 19645 19645 BU-61586DV6-150 BU-61586DV6-140 BU-61586DV6-150 BU-61586DV6-140 5962-9306541HYC S7631 5962-9306541HYC S7631 5962-9306541HYC 19645 5962-9306541HYC 19645 See footnotes at end of table. BU-61586DV6-130 BU-61586DV6-110 BU-61586DV6-130 BU-61586DV6-110 19 of 22 STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued. DATE: 02-07-15 Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-9306542HMA 5962-9306542HMA 5962-9306542HMA 5962-9306542HMA S7631 S7631 19645 19645 BU-61588CG3-150 BU-61588CG3-140 BU-61588CG3-150 BU-61588CG3-140 5962-9306542HMC 5962-9306542HMC 5962-9306542HMC 5962-9306542HMC S7631 S7631 19645 19645 BU-61588CG3-130 BU-61588CG3-110 BU-61588CG3-130 BU-61588CG3-110 5962-9306542HTA 5962-9306542HTA 5962-9306542HTA 5962-9306542HTA S7631 S7631 19645 19645 BU-61588CF3-150 BU-61588CF3-140 BU-61588CF3-150 BU-61588CF3-140 5962-9306542HTC 5962-9306542HTC 5962-9306542HTC 5962-9306542HTC S7631 S7631 19645 19645 BU-61588CF3-130 BU-61588CF3-110 BU-61588CF3-130 BU-61588CF3-110 5962-9306542HUA 5962-9306542HUA 5962-9306542HUA 5962-9306542HUA S7631 S7631 19645 19645 BU-61588CP3-150 BU-61588CP3-140 BU-61588CP3-150 BU-61588CP3-140 5962-9306542HUC 5962-9306542HUC 5962-9306542HUC 5962-9306542HUC S7631 S7631 19645 19645 BU-61588CP3-130 BU-61588CP3-110 BU-61588CP3-130 BU-61588CP3-110 5962-9306543HMA 5962-9306543HMA 5962-9306543HMA 5962-9306543HMA S7631 S7631 19645 19645 BU-65178CG3-150 BU-65178CG3-140 BU-65178CG3-150 BU-65178CG3-140 5962-9306543HMC 5962-9306543HMC 5962-9306543HMC 5962-9306543HMC S7631 S7631 19645 19645 BU-65178CG3-130 BU-65178CG3-110 BU-65178CG3-130 BU-65178CG3-110 5962-9306543HTA 5962-9306543HTA 5962-9306543HTA 5962-9306543HTA S7631 S7631 19645 19645 BU-65178CF3-150 BU-65178CF3-140 BU-65178CF3-150 BU-65178CF3-140 5962-9306543HTC 5962-9306543HTC 5962-9306543HTC 5962-9306543HTC S7631 S7631 19645 19645 BU-65178CF3-130 BU-65178CF3-110 BU-65178CF3-130 BU-65178CF3-110 5962-9306543HUA 5962-9306543HUA 5962-9306543HUA 5962-9306543HUA S7631 S7631 19645 19645 BU-65178CP3-150 BU-65178CP3-140 BU-65178CP3-150 BU-65178CP3-140 5962-9306543HUC S7631 5962-9306543HUC S7631 5962-9306543HUC 19645 5962-9306543HUC 19645 See footnotes at end of table. BU-65178CP3-130 BU-65178CP3-110 BU-65178CP3-130 BU-65178CP3-110 20 of 22 STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued. DATE: 02-07-15 Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-9306544HMA 5962-9306544HMA 5962-9306544HMA 5962-9306544HMA S7631 S7631 19645 19645 BU-65179CG3-150 BU-65179CG3-140 BU-65179CG3-150 BU-65179CG3-140 5962-9306544HMC 5962-9306544HMC 5962-9306544HMC 5962-9306544HMC S7631 S7631 19645 19645 BU-65179CG3-130 BU-65179CG3-110 BU-65179CG3-130 BU-65179CG3-110 5962-9306544HTA 5962-9306544HTA 5962-9306544HTA 5962-9306544HTA S7631 S7631 19645 19645 BU-65179CF3-150 BU-65179CF3-140 BU-65179CF3-150 BU-65179CF3-140 5962-9306544HTC 5962-9306544HTC 5962-9306544HTC 5962-9306544HTC S7631 S7631 19645 19645 BU-65179CF3-130 BU-65179CF3-110 BU-65179CF3-130 BU-65179CF3-110 5962-9306544HUA 5962-9306544HUA 5962-9306544HUA 5962-9306544HUA S7631 S7631 19645 19645 BU-65179CP3-150 BU-65179CP3-140 BU-65179CP3-150 BU-65179CP3-140 5962-9306544HUC 5962-9306544HUC 5962-9306544HUC 5962-9306544HUC S7631 S7631 19645 19645 BU-65179CP3-130 BU-65179CP3-110 BU-65179CP3-130 BU-65179CP3-110 5962-9306545HMA 5962-9306545HMA 5962-9306545HMA 5962-9306545HMA S7631 S7631 19645 19645 BU-61688BG3-150 BU-61688BG3-140 BU-61688BG3-150 BU-61688BG3-140 5962-9306545HMC 5962-9306545HMC 5962-9306545HMC 5962-9306545HMC S7631 S7631 19645 19645 BU-61688BG3-130 BU-61688BG3-110 BU-61688BG3-130 BU-61688BG3-110 5962-9306545HTA 5962-9306545HTA 5962-9306545HTA 5962-9306545HTA S7631 S7631 19645 19645 BU-61688BF3-150 BU-61688BF3-140 BU-61688BF3-150 BU-61688BF3-140 5962-9306545HTC 5962-9306545HTC 5962-9306545HTC 5962-9306545HTC S7631 S7631 19645 19645 BU-61688BF3-130 BU-61688BF3-110 BU-61688BF3-130 BU-61688BF3-110 5962-9306545HUA 5962-9306545HUA 5962-9306545HUA 5962-9306545HUA S7631 S7631 19645 19645 BU-61688BP3-150 BU-61688BP3-140 BU-61688BP3-150 BU-61688BP3-140 5962-9306545HUC S7631 5962-9306545HUC S7631 5962-9306545HUC 19645 5962-9306545HUC 19645 See footnotes at end of table. BU-61688BP3-130 BU-61688BP3-110 BU-61688BP3-130 BU-61688BP3-110 21 of 22 STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued. DATE: 02-07-15 1/ 2/ 3/ Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-9306546HMA 5962-9306546HMA 5962-9306546HMA 5962-9306546HMA S7631 S7631 19645 19645 BU-61689BG3-150 BU-61689BG3-140 BU-61689BG3-150 BU-61689BG3-140 5962-9306546HMC 5962-9306546HMC 5962-9306546HMC 5962-9306546HMC S7631 S7631 19645 19645 BU-61689BG3-130 BU-61689BG3-110 BU-61689BG3-130 BU-61689BG3-110 5962-9306546HTA 5962-9306546HTA 5962-9306546HTA 5962-9306546HTA S7631 S7631 19645 19645 BU-61689BF3-150 BU-61689BF3-140 BU-61689BF3-150 BU-61689BF3-140 5962-9306546HTC 5962-9306546HTC 5962-9306546HTC 5962-9306546HTC S7631 S7631 19645 19645 BU-61689BF3-130 BU-61689BF3-110 BU-61689BF3-130 BU-61689BF3-110 5962-9306546HUA 5962-9306546HUA 5962-9306546HUA 5962-9306546HUA S7631 S7631 19645 19645 BU-61689BP3-150 BU-61689BP3-140 BU-61689BP3-150 BU-61689BP3-140 5962-9306546HUC 5962-9306546HUC 5962-9306546HUC 5962-9306546HUC S7631 S7631 19645 19645 BU-61689BP3-130 BU-61689BP3-110 BU-61689BP3-130 BU-61689BP3-110 The lead finish shown for each PIN, representing a hermetic package, is the most readily available from the manufacturer listed for that part. If the desired lead finish is not listed contact the Vendor to determine its availability. Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. Not available from a QML source. Vendor CAGE number Vendor name and address S7631 DDC Ireland, LTD. Cork Business & Technology Park Model Farm Road Cork, Ireland 19645 Data Device Corporation 105 Wilbur Place Bohemia, NY 11716-2482 The information contained herein is disseminated for convenience only and the Government assumes no liability whatsoever for any inaccuracies in the information bulletin. 22 of 22