LH534A00 FEATURES CMOS 4M (512K × 8) MROM PIN CONNECTIONS • 524,288 words × 8 bit organization • Access time: 120 ns (MAX.) • Static operation • TTL compatible I/O • Three-state outputs • Single +5 V power supply • Power consumption: Operating: 357.5 mW (MAX.) Standby: 550 µW (MAX.) TOP VIEW 32-PIN TSOP (Type I) A11 1 32 OE A9 2 31 A10 A8 3 30 CE A13 4 29 D7 A14 5 28 D6 A17 6 27 D5 NC 7 26 D4 D3 VCC 8 25 A18 9 24 GND A16 10 23 D2 A15 11 22 D1 A12 12 21 D0 A7 13 20 A0 A6 14 19 A1 DESCRIPTION A5 15 18 A2 The LH534A00 is a 4M-bit mask-programmable ROM organized as 524,288 × 8 bits. It is fabricated using silicon-gate CMOS process technology. A4 16 17 A3 • Package: 32-pin, 8 × 20 mm2 TSOP (Type I) 534A00-1 Figure 1. Pin Connections for TSOP Package 1 LH534A00 CMOS 4M MROM A18 9 A17 6 10 11 5 4 ADDRESS BUFFER A12 12 A11 1 A10 31 A9 A8 A7 A6 2 3 13 14 MEMORY MATRIX (524,288 x 8) ADDRESS DECODER A16 A15 A14 A13 A5 15 A4 16 A3 17 A2 18 A1 19 COLUMN SELECTOR A0 20 SENSE AMPLIFIER CE BUFFER CE 30 TIMING GENERATOR OUTPUT BUFFER OE BUFFER OE 32 8 24 VCC GND 21 D0 22 D1 23 D2 25 D3 26 D4 27 D5 28 D6 29 D7 534A00-2 Figure 2. LH534A00 Block Diagram PIN DESCRIPTION SIGNAL SIGNAL PIN NAME A0 – A18 Address input OE Output enable input D0 – D7 Data output VCC Power supply (+5 V) Chip enable input GND Ground CE 2 PIN NAME CMOS 4M MROM LH534A00 TRUTH TABLE CE OE DATA OUTPUT SUPPLY CURRENT H X High-Z Standby H High-Z Operating L Output Operating L NOTE: X = H or L, High-Z = High-impedance ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL RATING UNIT Supply voltage VCC – 0.3 to +7.0 V Input voltage VIN – 0.3 to V CC + 0.3 V Output voltage VOUT – 0.3 to V CC + 0.3 V Operating temperature Topr –20 to +70 °C Storage temperature Tstg –65 to +150 °C RECOMMENDED OPERATING CONDITIONS (TA = –20°C to +70°C) PARAMETER SYMBOL MIN. TYP. MAX. UNIT Supply voltage VCC 4.5 5.0 5.5 V DC CHARACTERISTICS (VCC = 5 V ±10%, TA = –20°C to +70°C) PARAMETER SYMBOL CONDITIONS MIN. MAX. UNIT NOTE Input ‘High’ voltage VIH 2.2 VCC + 0.3 V Input ‘Low’ voltage VIL – 0.3 0.8 V Output ‘High’ voltage VOH I OH = –400 µA Output ‘Low’ voltage VOL I OL = 2.0 mA 0.4 V Input leakage current | ILl | V IN = 0 V to VCC 10 µA Output leakage current | ILO | V OUT = 0 V to VCC 10 µA 1 ICC1 t RC = 120 ns 65 mA 2 ICC2 t RC = 1 µs 50 mA 2 ICC3 t RC = 120 ns 60 mA 3 ICC4 t RC = 1 µs 45 mA 3 ISB1 CE = V IH 3 mA ISB2 CE = V CC – 0.2 V 100 µA CIN f = 1 MHz T A = 25°C 10 pF 10 pF Operating current Standby current Input capacitance Output capacitance COUT 2.4 V NOTES: 1. CE/OE = VIH 2. VIN = VIH or VIL, CE = VIL, outputs open 3. VIN = (VCC – 0.2 V) or 0.2 V, CE = 0.2 V, outputs open 3 LH534A00 CMOS 4M MROM AC CHARACTERISTICS (VCC = 5 V ±10%, TA = –20°C to +70°C) PARAMETER SYMBOL MIN. MAX. UNIT Read cycle time tRC 120 Address access time tAA 120 ns Chip enable access time tACE 120 ns Output enable delay time tOE 60 ns Output hold time tOH CE to output in High-Z tCHZ OE to output in High-Z tOHZ NOTE ns 0 ns 60 ns 1 NOTE: 1. This is the time required for the outputs to become high-impedance. AC TEST CONDITIONS PARAMETER RATING Input voltage amplitude 0.4 to 2.6 V Input rise/fall time 10 ns Input/output reference level 1.5 V Output load condition 1 TTL + 100 pF CAUTION To stabilize the power supply, it is recommended that a high-frequency bypass capacitor be connected between the VCC pin and the GND pin. tRC A0 - A18 tAA (NOTE) CE tACE tCHZ (NOTE) OE tOHZ tOE (NOTE) D0 - D7 tOH DATA VALID NOTE: The output data becomes valid when the last intervals, tAA, tACE, or tOE, have concluded. Figure 3. Timing Diagram 4 534A00-3 CMOS 4M MROM LH534A00 PAGKAGE DIAGRAM 32TSOP (Type I) (TSOP032-P-0820) 0.30 [0.012] 0.10 [0.004] 0.50 [0.020] TYP. 32 17 18.60 [0.732] 18.20 [0.717] 1 20.30 [0.799] 19.70 [0.776] 19.00 [0.748] 16 8.20 [0.323] 7.80 [0.307] 0.20 [0.008] 0.10 [0.004] 0.15 [0.006] 1.10 [0.043] 0.90 [0.035] 1.20 [0.047] MAX. 0.425 [0.017] 0.20 [0.008] 0.00 [0.000] DIMENSIONS IN MM [INCHES] MAXIMUM LIMIT MINIMUM LIMIT 32TSOP 32-pin, 8 × 20 mm2 TSOP (Type I) ORDERING INFORMATION LH534A00 Device Type T Package 32-pin, 8 x 20 mm2 TSOP (Type I) (TSOP032-P-0820) CMOS 4M (512K x 8) Mask-Programmable ROM Example: LH534A00T (CMOS 4M (512K x 8) Mask-Programmable ROM, 32-pin, 8 x 20 mm2 TSOP (Type I)) 534A00-4 5