TI TK500

SCDS212B − SEPTEMBER 2005 − REVISED APRIL 2006
D
49 GND
50 VCC
51 2LED2
52 2LED1
53 GND
54 LED2
55 GND
56 VCC
48 0B1
A0
A1
2
47 1B1
3
46 0B2
VCC
NC
4
45 1B2
5
44 GND
GND
6
43 2B1
A2
A3
7
42 3B1
8
41 2B2
GND
9
40 3B2
VCC 10
A4 11
39 GND
A5 12
GND 13
37 4B1
A6 14
A7 15
35 4B2
38 VCC
36 5B1
34 5B2
GND 16
33 GND
SEL 17
32 6B1
VCC 18
LED0 19
LED1 20
31 7B1
30 6B2
29 7B2
description/ordering information
The TS3L500 is a 16-bit to 8-bit multiplexer/
demultiplexer LAN switch with a single select
(SEL) input. SEL controls the data path of the
multiplexer/demultiplexer. The device provides
additional I/Os for switching status indicating LED
signals.
VCC 27
GND 28
D
1
GND 24
D
D
GND
0LED2 25
1LED2 26
D
TQFN PACKAGE
(TOP VIEW)
GND 21
D
Wide Bandwidth (BW > 1100 MHz Typ)
Low Crosstalk (XTALK = −37 dB Typ)
Low Bit-to-Bit Skew (tsk(o) = 100 ps Max)
Low and Flat ON-State Resistance
(ron = 4 Typ, ron(flat) = 0.5 Typ)
Low Input/Output Capacitance
(CON = 8 pF Typ)
Rail-to-Rail Switching on Data I/O Ports
(0 to 5 V)
VCC Operating Range From 3 V to 3.6 V
Latch-Up Performance Exceeds 100 mA Per
JESD 78, Class II
ESD Performance Tested Per JESD 22
− 2000-V Human-Body Model
(A114-B, Class II)
− 1000-V Charged-Device Model (C101)
Applications
− 10/100/1000 Base-T Signal Switching
− Differential (LVDS, LVPECL) Signal
Switching
− Audio/Video Switching
− Hub and Router Signal Switching
0LED1 22
1LED1 23
D
D
D
D
The device provides a low and flat ON-state resistance (ron) and an excellent ON-state resistance match. Low
input/output capacitance, high bandwidth, low skew, and low crosstalk among channels make this device
suitable for various LAN applications, such as 10/100/1000 Base-T.
This device can be used to replace mechanical relays in LAN applications. It also can be used to route signals
from a 10/100 Base-T ethernet transceiver to the RJ-45 LAN connectors in laptops or in docking stations.
ORDERING INFORMATION
TA
PACKAGE†
ORDERABLE
PART NUMBER
TOP-SIDE
MARKING
−40°C to 85°C
TQFN
Tape and reel
TS3L500RHUR
TK500
† Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines
are available at www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  2006, Texas Instruments Incorporated
! " #$%! " &$'(#! )!%*
)$#!" # ! "&%##!" &% !+% !%" %," "!$%!"
"!)) -!.* )$#! &#%""/ )%" ! %#%""(. #($)%
!%"!/ (( &%!%"*
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SCDS212B − SEPTEMBER 2005 − REVISED APRIL 2006
FUNCTION TABLE
INPUT
SEL
INPUT/OUTPUT
An
FUNCTION
L
nB1
nB2
An = nB1, LEDx = XLED1
An = nB2, LEDx = XLED2
H
PIN DESCRIPTION
DESCRIPTION
NAME
An
nBm
SEL
LEDx
XLEDm
2
Data I/O
Data I/O
Select input
LED I/O port
LED I/O port
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SCDS212B − SEPTEMBER 2005 − REVISED APRIL 2006
logic diagram (positive logic)
2
48
3
47
0B1
A0
1B1
A1
46
0B2
45
1B2
7
43
8
42
2B1
A2
3B1
A3
41
2B2
40
3B2
11
37
12
36
4B1
A4
5B1
A5
35
4B2
34
5B2
14
32
15
31
6B1
A6
7B1
A7
30
6B2
29
7B2
19
22
LED0
25
LED1
20
23
26
LED2
52
54
51
SEL
0LED1
0LED2
1LED1
1LED2
2LED1
2LED2
17
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
SCDS212B − SEPTEMBER 2005 − REVISED APRIL 2006
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 4.6 V
Control input voltage range, VIN (see Notes 1 and 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V
Switch I/O voltage range, VI/O (see Notes 1, 2, and 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V
Control input clamp current, IIK (VIN < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −50 mA
I/O port clamp current, II/OK (VI/O < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −50 mA
ON-state switch current, II/O (see Note 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±128 mA
Continuous current through VCC or GND terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±100 mA
Package thermal impedance, θJA (see Note 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31.8°C/W
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltages are with respect to ground, unless otherwise specified.
2. The input and output voltage ratings may be exceeded if the input and output clamp-current ratings are observed.
3. VI and VO are used to denote specific conditions for VI/O.
4. II and IO are used to denote specific conditions for II/O.
5. The package thermal impedance is calculated in accordance with JESD 51-7.
recommended operating conditions (see Note 6)
MIN
MAX
VCC
VIH
Supply voltage
3
3.6
UNIT
V
High-level control input voltage (SEL)
2
5.5
V
VIL
VI/O
Low-level control input voltage (SEL)
0
0.8
V
Input/output voltage
0
5.5
V
TA
Operating free-air temperature
−40
85
°C
NOTE 6: All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SCDS212B − SEPTEMBER 2005 − REVISED APRIL 2006
electrical characteristics for 1000 Base-T ethernet switching over recommended operating free-air
temperature range, VCC = 3.3 V + 0.3 V (unless otherwise noted)†
PARAMETER
VIK
IIH
SEL
IIL
ICC
SEL
CIN
COFF
TEST CONDITIONS
MIN
VCC = 3.6 V,
VCC = 3.6 V,
IIN = −18 mA
VIN = VCC
VCC = 3.6 V,
VCC = 3.6 V,
VIN = GND
II/O = 0,
Switch ON or OFF
SEL
f = 1 MHz,
B port
VI = 0,
VIN = 0
f = 1 MHz,
Outputs open,
Switch OFF
CON
VI = 0,
f = 1 MHz,
Outputs open,
Switch ON
ron
VCC = 3 V,
1.5 V ≤ VI ≤ VCC,
ron(flat)§
VCC = 3 V,
VI = 1.5 V and VCC,
SEL
TYP‡
MAX
UNIT
−0.7
−1.2
V
±1
µA
±1
µA
250
500
µA
2
2.5
pF
2.5
4
pF
8
9
pF
IO = −40 mA
4
6
Ω
IO = −40 mA
0.5
VCC = 3 V,
1.5 V ≤ VI ≤ VCC,
IO = −40 mA
∆ron¶
† VI, VO, II, and IO refer to I/O pins. VIN refers to the control inputs.
‡ All typical values are at VCC = 3.3 V (unless otherwise noted), TA = 25°C.
§ ron(flat) is the difference of ron in a given channel at specified voltages.
¶ ∆ron is the difference of ron from center (A4, A5) ports to any other port.
0.4
Ω
1
Ω
electrical characteristics for 10/100 Base-T ethernet switching over recommended operating
free-air temperature range, VCC = 3.3 V + 0.3 V (unless otherwise noted)†
PARAMETER
VIK
IIH
SEL
IIL
ICC
SEL
CIN
COFF
TEST CONDITIONS
VCC = 3.6 V,
VCC = 3.6 V,
IIN = −18 mA
VIN = VCC
VCC = 3.6 V,
VCC = 3.6 V,
VIN = GND
II/O = 0,
SEL
f = 1 MHz,
B port
SEL
MIN
Switch ON or OFF
TYP‡
MAX
−0.7
−1.2
V
±1
µA
±1
µA
250
500
µA
2
2.5
pF
2.5
4
pF
VI = 0,
VIN = 0
f = 1 MHz,
Outputs open,
Switch OFF
CON
VI = 0,
f = 1 MHz,
Outputs open,
Switch ON
ron
VCC = 3 V,
1.25 V ≤ VI ≤ VCC,
IO = −10 mA to −30 mA
4
ron(flat)§
VCC = 3 V,
VI = 1.25 V and VCC,
IO = −10 mA to −30 mA
0.5
VCC = 3 V,
1.25 V ≤ VI ≤ VCC,
IO = −10 mA to −30 mA
† VI, VO, II, and IO refer to I/O pins. VIN refers to the control inputs.
‡ All typical values are at VCC = 3.3 V (unless otherwise noted), TA = 25°C.
§ ron(flat) is the difference of ron in a given channel at specified voltages.
¶ ∆ron is the difference of ron from center (A4, A5) ports to any other port.
0.4
∆ron¶
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
UNIT
8
pF
6
Ω
Ω
1
Ω
5
SCDS212B − SEPTEMBER 2005 − REVISED APRIL 2006
switching characteristics over recommended operating free-air temperature range,
VCC = 3.3 V + 0.3 V, RL = 200 Ω, CL = 10 pF (unless otherwise noted) (see Figures 4 and 5)
FROM
(INPUT)
TO
(OUTPUT)
A or B
B or A
tPZH, tPZL
SEL
A or B
0.5
15
ns
tPHZ, tPLZ
tsk(o)§
SEL
A or B
0.9
9
ns
A or B
B or A
50
100
ps
50
150
ps
PARAMETER
tpd‡
tsk(p)¶
MIN
TYP†
MAX
0.25
UNIT
ns
† All typical values are at VCC = 3.3 V (unless otherwise noted), TA = 25°C.
‡ The propagation delay is the calculated RC time constant of the typical ON-state resistance of the switch and the specified load capacitance when
driven by an ideal voltage source (zero output impedance).
§ Output skew between center port (A4 to A5) to any other port
¶ Skew between opposite transitions of the same output in a given device |tPHL − tPLH|
dynamic characteristics over recommended operating free-air temperature range,
VCC = 3.3 V + 0.3 V (unless otherwise noted)
TEST CONDITIONS
TYP†
XTALK
OIRR
RL = 100 Ω,
f = 250 MHz,
See Figure 8
−37
RL = 100 Ω,
f = 250 MHz,
See Figure 9
BW
RL = 100 Ω,
See Figure 7
PARAMETER
† All typical values are at VCC = 3.3 V (unless otherwise noted), TA = 25°C.
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
UNIT
dB
−37
dB
1100
MHz
SCDS212B − SEPTEMBER 2005 − REVISED APRIL 2006
OPERATING CHARACTERISTICS
0
0
−2
−20
Attenuation (dB)
Gain (dB)
−4
−6
−8
−10
−12
0.1
1
10
100
1000
−40
−60
−80
−100
0.1
10,000
1
Frequency (MHz)
Figure 1. Gain vs Frequency
1000
10,000
Figure 2. OFF Isolation vs Frequency
0
6
5
−20
4
ron ()
Attenuation (dB)
10
100
Frequency (MHz)
−40
−60
3
2
−80
−100
0.1
1
0
1
10
100
Frequency (MHz)
1000
10,000
0
1
2
3
4
5
6
VCOM (V)
Figure 3. Crosstalk vs Frequency
POST OFFICE BOX 655303
Figure 4. ron () vs Vcom (V)
• DALLAS, TEXAS 75265
7
SCDS212B − SEPTEMBER 2005 − REVISED APRIL 2006
PARAMETER MEASUREMENT INFORMATION
Enable and Disable Times
VCC
Input Generator
VIN
50 Ω
50 Ω
VG1
TEST CIRCUIT
DUT
Input Generator
VI
S1
RL
VO
CL
(see Note A)
50 Ω
RL
TEST
VCC
S1
RL
Vin
CL
V∆
tPLZ/tPZL
3.3 V ± 0.3 V
2 × VCC
200 Ω
GND
10 pF
0.3 V
tPHZ/tPZH
3.3 V ± 0.3 V
GND
200 Ω
VCC
10 pF
0.3 V
VO
2.5 V
Output Control
(VIN)
Output
Waveform 1
S1 at 2 y VCC
(see Note B)
1.25 V
1.25 V
0V
tPZL
tPLZ
VOH
VCC/2
tPZH
VO
Open
GND
50 Ω
VG2
VI
2 × VCC
Output
Waveform 2
S1 at GND
(see Note B)
VOL + 0.3 V
VOL
tPHZ
VCC/2
VOH − 0.3 V
VOH
VOL
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
NOTES: A. CL includes probe and jig capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns.
D. The outputs are measured one at a time, with one transition per measurement.
E. tPLZ and tPHZ are the same as tdis.
F. tPZL and tPZH are the same as ten.
Figure 5. Test Circuit and Voltage Waveforms
8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SCDS212B − SEPTEMBER 2005 − REVISED APRIL 2006
PARAMETER MEASUREMENT INFORMATION
Skew
VCC
Input Generator
VIN
50 Ω
50 Ω
VG1
TEST CIRCUIT
DUT
Input Generator
Open
RL
TEST
VCC
S1
RL
Vin
CL
tsk(o)
3.3 V ± 0.3 V
Open
200 Ω
VCC or GND
10 pF
tsk(p)
3.3 V ± 0.3 V
Open
200 Ω
VCC or GND
10 pF
3.5 V
2.5 V
1.5 V
Data In at
Ax or Ay
tPHLx
VOH
(VOH + VOL)/2
VOL
Data Out at
XB1 or XB2
tsk(o)
VO
CL
(see Note A)
50 Ω
tPLHx
VO
2 × VCC
S1
GND
50 Ω
VG2
VI
RL
VO
VI
3.5 V
2.5 V
1.5 V
Input
tsk(o)
VOH
(VOH + VOL)/2
VOL
Data Out at
YB1 or YB2
tPLHy
tPHLy
tPLH
Output
tsk(o) = tPLHy − tPLHx or tPHLy − tPHLx
VOLTAGE WAVEFORMS
OUTPUT SKEW (tsk(o))
tPHL
VOH
(VOH + VOL)/2
VOL
tsk(p) = tPHL − tPLH
VOLTAGE WAVEFORMS
PULSE SKEW [tsk(p)]
NOTES: A. CL includes probe and jig capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns.
D. The outputs are measured one at a time, with one transition per measurement.
Figure 6. Test Circuit and Voltage Waveforms
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
SCDS212B − SEPTEMBER 2005 − REVISED APRIL 2006
PARAMETER MEASUREMENT INFORMATION
EXT TRIGGER
BIAS
Network Analyzer
(HP8753ES)
VBIAS
P1
P2
VCC
A0
SEL
0B1
CL = 10 pF
(see Note A)
DUT
VSEL
NOTE A: CL includes probe and jig capacitance.
Figure 7. Test Circuit for Frequency Response (BW)
Frequency response is measured at the output of the ON channel. For example, when VSEL = 0 and A0 is the input,
the output is measured at 0B1. All unused analog I/O ports are left open.
HP8753ES setup
Average = 4
RBW = 3 kHz
VBIAS = 0.35 V
ST = 2 s
P1 = 0 dBM
10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SCDS212B − SEPTEMBER 2005 − REVISED APRIL 2006
PARAMETER MEASUREMENT INFORMATION
EXT TRIGGER
BIAS
VBIAS
Network Analyzer
(HP8753ES)
P1
P2
VCC
0B1
A0
RL = 100 Ω
A1
1B1
0B2
DUT
A2
1B2
2B1
RL = 100 Ω
A3
3B1
2B2
3B2
SEL
VSEL
NOTES: A. CL includes probe and jig capacitance.
B. A 50-Ω termination resistor is needed to match the loading of the network analyzer.
Figure 8. Test Circuit for Crosstalk (XTALK)
Crosstalk is measured at the output of the nonadjacent ON channel. For example, when VSEL = 0
and A0 is the input, the output is measured at 1B1. All unused analog input (A) ports are connected to GND, and output
(B) ports are connected to GND through 50-Ω pulldown resistors.
HP8753ES setup
Average = 4
RBW = 3 kHz
VBIAS = 0.35 V
ST = 2 s
P1 = 0 dBM
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
SCDS212B − SEPTEMBER 2005 − REVISED APRIL 2006
PARAMETER MEASUREMENT INFORMATION
EXT TRIGGER
BIAS
VBIAS
Network Analyzer
(HP8753ES)
P1
P2
VCC
A0
0B1
RL = 100 Ω
A1
1B1
DUT
0B2
1B2
SEL
VSEL
NOTES: A. CL includes probe and jig capacitance.
B. A 50-Ω termination resistor is needed to match the loading of the network analyzer.
Figure 9. Test Circuit for OFF Isolation (OIRR)
OFF isolation is measured at the output of the OFF channel. For example, when VSEL = VCC and A0 is the input, the
output is measured at 0B2. All unused analog input (A) ports are left open, and output (B) ports are connected to GND
through 50-Ω pulldown resistors.
HP8753ES setup
Average = 4
RBW = 3 kHz
VBIAS = 0.35 V
ST = 2 s
P1 = 0 dBM
12
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
PACKAGE OPTION ADDENDUM
www.ti.com
5-Feb-2007
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
TS3L500RHUR
ACTIVE
QFN
RHU
Pins Package Eco Plan (2)
Qty
56
2000 Green (RoHS &
no Sb/Br)
Lead/Ball Finish
CU NIPDAU
MSL Peak Temp (3)
Level-1-260C-UNLIM
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to
discontinue any product or service without notice. Customers should obtain the latest relevant information
before placing orders and should verify that such information is current and complete. All products are sold
subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent
TI deems necessary to support this warranty. Except where mandated by government requirements, testing
of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible
for their products and applications using TI components. To minimize the risks associated with customer
products and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent
right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine,
or process in which TI products or services are used. Information published by TI regarding third-party
products or services does not constitute a license from TI to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or
other intellectual property of the third party, or a license from TI under the patents or other intellectual
property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices.
Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not
responsible or liable for such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for
that product or service voids all express and any implied warranties for the associated TI product or service
and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Low Power Wireless
www.ti.com/lpw
Telephony
www.ti.com/telephony
Mailing Address:
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated