UPC8232T5N

BIPOLAR ANALOG INTEGRATED CIRCUIT
µPC8232T5N
ED
SiGe:C LOW NOISE AMPLIFIER FOR GPS
DESCRIPTION
The µPC8232T5N is a silicon germanium carbon (SiGe:C) monolithic integrated circuit designed as low noise
amplifier for GPS. This device exhibits low noise figure and high power gain characteristics, so this IC can improve the
sensitivity of GPS receiver. In addition, the µPC8232T5N which is included output matching circuit contributes to
IN
U
reduce external components and system size.
The package is a 6-pin plastic TSON (Thin Small Out-line Non-leaded) suitable for surface mount.
This IC is manufactured using our UHS4 (Ultra High Speed Process) SiGe:C bipolar process.
FEATURES
• Low noise
: NF = 0.95 dB TYP. @ fin = 1 575 MHz
• High gain
: GP = 17 dB TYP. @ fin = 1 575 MHz
• Low current consumption
: ICC = 3.0 mA TYP. @ VCC = 3.0 V
• Built-in power-saving function
O
NT
• High-density surface mounting : 6-pin plastic TSON package (1.5 × 1.5 × 0.37 mm)
• Included output matching circuit
• Included very robust bandgap regulator (Small VCC and TA dependence)
• Included protection circuits for ESD
APPLICATION
• Low noise amplifier for GPS
ORDERING INFORMATION
Part Number
µPC8232T5N-E2-A
Package
6-pin plastic TSON
DI
SC
µPC8232T5N-E2
Order Number
(Pb-Free)
Marking
6L
Supplying Form
• 8 mm wide embossed taping
• Pin 1, 6 face the perforation side of the tape
• Qty 3 kpcs/reel
Remark To order evaluation samples, contact your nearby sales office.
Part number for sample order: µPC8232T5N-A
Caution Observe precautions when handling because these devices are sensitive to electrostatic discharge.
Document No. PU10672EJ01V0DS (1st edition)
Date Published July 2007 NS
2007
µPC8232T5N
PIN CONNECTIONS AND INTERNAL BLOCK DIAGRAM
3
6
1
6
6
5
2
5
5
4
Bias
2
6L
1
(Bottom View)
(Top View)
3
4
1
Pin No.
Pin Name
1
VCC
2
GND
3
INPUT
4
Power Save
5
OUTPUT
6
VCC
ED
(Top View)
2
3
4
Remark Exposed pad : GND
Parameter
IN
U
ABSOLUTE MAXIMUM RATINGS
Symbol
Test Conditions
Ratings
Unit
VCC
TA = +25°C
4.0
V
Power-Saving Voltage
VPS
TA = +25°C
4.0
V
Total Power Dissipation
Ptot
150
mW
Operating Ambient Temperature
TA
−40 to +85
°C
Storage Temperature
Tstg
−55 to +150
°C
Input Power
Pin
+10
dBm
O
NT
Supply Voltage
RECOMMENDED OPERATING RANGE
Parameter
Symbol
MIN.
TYP.
MAX.
Unit
VCC
2.5
3.0
3.3
V
TA
−40
+25
+85
°C
Power Save Turn-on Voltage
VPSon
1.6
−
VCC
V
Power Save Turn-off Voltage
VPSoff
0
−
0.4
V
Supply Voltage
DI
SC
Operating Ambient Temperature
2
Data Sheet PU10672EJ01V0DS
µPC8232T5N
ELECTRICAL CHARACTERISTICS
(TA = +25°C, VCC = VPS = 3.0 V, fin = 1 575 MHz, unless otherwise specified)
Symbol
Circuit Current
ICC
Test Conditions
No Signal (VPS = 3.0 V)
At Power-Saving Mode (VPS = 0 V)
Power Gain
GP
Noise Figure
NF
Input 3rd Order Distortion Intercept
IIP3
Pin = −35 dBm
fin1 = 1 574 MHz, fin2 = 1 575 MHz
Input Return Loss
RLin
Output Return Loss
RLout
Isolation
ISL
Gain 1 dB Compression Input Power
Pin (1 dB)
TEST CIRCUIT
VCC
1
Unit
2.3
3.0
4.1
mA
−
−
1
µA
15
17
19
dB
−
0.95
1.25
dB
−
−8
−
dBm
7
10
−
dB
10
20
−
dB
−
40
−
dB
−
−21
−
dBm
6
O
NT
2
3
5
4
OUTPUT
1 pF
VPS
5.6 nH
DI
SC
100 pF
MAX.
1 000 pF
1 000 pF
INPUT
TYP.
IN
U
Point
MIN.
ED
Parameter
Data Sheet PU10672EJ01V0DS
3
µPC8232T5N
TYPICAL CHARACTERISTICS (TA = +25°C, unless otherwise specified)
NOISE FIGURE vs. FREQUENCY
POWER GAIN vs. FREQUENCY
22
1.6
TA = –40°C
18
16
+25°C
14
+85°C
12
0.8
+25°C
0.6
0.4
–40°C
1 600
1 575
1 625 1 650
22
TA = –40°C
Noise Figure NF (dB)
+25°C
+85°C
12
2.6
2.8
3.0
3.2
3.4
1.0
0.8
+25°C
0.6
0.4
0
2.2
3.6
–40°C
2.4
2.6
3.0
2.8
VCC = VPS
fin = 1 575 MHz
3.2 3.4
3.6
Supply Voltage VCC (V)
POWER GAIN vs. OPERATING
AMBIENT TEMPERATURE
NOISE FIGURE vs. OPERATING
AMBIENT TEMPERATURE
DI
SC
Supply Voltage VCC (V)
1.6
22
1.4
Noise Figure NF (dB)
20
18
16
14
12
10
–50
1.2
0.2
VCC = VPS
fin = 1 575 MHz
2.4
1 625 1 650
TA = +85°C
O
NT
14
VCC = VPS = 3 V
1 600
1.4
20
16
1 575
NOISE FIGURE vs. SUPPLY VOLTAGE
1.6
18
1 550
Frequency fin (MHz)
POWER GAIN vs. SUPPLY VOLTAGE
10
2.2
0
1 500 1 525
IN
U
VCC = VPS = 3 V
1 550
Frequency fin (MHz)
Power Gain GP (dB)
1.0
0.2
10
1 500 1 525
Power Gain GP (dB)
1.2
ED
Noise Figure NF (dB)
Power Gain GP (dB)
20
0
25
50
75
1.0
0.8
0.6
0.4
0.2
VCC = VPS = 3 V
fin = 1 575 MHz
–25
1.2
100
0
–50
Operating Ambient Temperature TA (°C)
Remark The graphs indicate nominal characteristics.
4
TA = +85°C
1.4
Data Sheet PU10672EJ01V0DS
VCC = VPS = 3 V
fin = 1 575 MHz
–25
0
25
50
75
Operating Ambient Temperature TA (°C)
100
µPC8232T5N
POWER GAIN, CIRCUIT CURRENT
vs. INPUT POWER
22
VCC = VPS = 3 V
fin = 1 575 MHz
–20
10
18
8
GP
ED
–10
16
6
14
12
2
Pin (1dB) = –21.9 dBm
–20
–10
–15
–30
–50
VCC = VPS = 3 V
fin = 1 575 MHz
–25
25
0
50
OUTPUT POWER, IM3 vs. INPUT POWER
VCC = VPS = 3 V
fin1 = 1 574 MHz
0 fin2 = 1 575 MHz
100
75
–40
IM3
–60
–80
–100
–40
IIP3 = –8.2 dBm
–30
–20
–10
0
Input Power Pin (dBm)
K FACTOR vs. FREQUENCY
20
DI
SC
OIP3
10
0
–5
IIP3
–10
–15
–25
0
25
VCC = VPS = 3 V
15
5
K factor K
Input 3rd Order Distortion Intercept Point IIP3 (dBm)
Output 3rd Order Distortion Intercept Point OIP3 (dBm)
Pout
–20
IIP3, OIP3 vs. OPERATING AMBIENT
TEMPERATURE
–20
–50
0
0
20
Operating Ambient Temperature TA (°C)
15
–10
–20
–30
Input Power Pin (dBm)
GAIN 1 dB COMPRESSION INPUT POWER
vs. OPERATING AMBIENT TEMPERATURE
–25
–40
O
NT
Gain 1 dB Compression Input Power Pin (1 dB) (dB)
Input Power Pin (dBm)
–20
10
–50
–10
IN
U
–30
Output Power Pout (dBm)
3rd Order Intermodulation Distortion IM3 (dBm)
–40
4
ICC
Pin (1dB) = –21.9 dBm
–30
–50
12
VCC = VPS = 3 V
fin = 1 575 MHz
20
0
Power Gain GP (dB)
Output Power Pout (dBm)
10
Circuit Current ICC (mA)
OUTPUT POWER vs. INPUT POWER
10
5
VCC = VPS = 3 V
fin1 = 1 574 MHz
fin2 = 1 575 MHz
100
50
75
1
0
0
Operating Ambient Temperature TA (°C)
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
Frequency fin (GHz)
Remark The graphs indicate nominal characteristics.
Data Sheet PU10672EJ01V0DS
5
µPC8232T5N
CIRCUIT CURRENT vs.
POWER-SAVING VOLTAGE
CIRCUIT CURRENT vs. SUPPLY VOLTAGE
5
3
+25°C
2
–40°C
1
TA = +85°C
4
3
2
1
VCC = 3 V
RF = off
3.5
3.0
4.0
0
0
Supply Voltage VCC (V)
4
1
O
NT
Circuit Current ICC (mA)
5
2
VCC = VPS = 3 V
RF = off
0
–50
–25
0
25
50
75
100
Operating Ambient Temperature TA (°C)
DI
SC
Remark The graphs indicate nominal characteristics.
6
1.0
1.5
2.0
2.5
Power-Saving Voltage VPS (V)
CIRCUIT CURRENT vs. OPERATING
AMBIENT TEMPERATURE
3
0.5
IN
U
2.5
+25°C
–40°C
VCC = VPS
RF = off
0
2.0
ED
TA = +85°C
4
Circuit Current ICC (mA)
Circuit Current ICC (mA)
5
Data Sheet PU10672EJ01V0DS
3.0
µPC8232T5N
S-PARAMETERS (TA = +25°C, VCC = VPS = 3.0 V, monitored at connector on board)
S11–FREQUENCY
S22–FREQUENCY
1:1 575 MHz
56.751 Ω
–0.650 Ω
1:1 575 MHz
38.436 Ω
28.429 Ω
ED
1
START 100.000 MHz
IN
U
1
START 100.000 MHz
STOP 4 100.000 MHz
OUTPUT RETURN LOSS vs. FREQUENCY
INPUT RETURN LOSS vs. FREQUENCY
0
Output Return Loss RLout (dB)
–5
–10
–15
–20
–25
0
500
–5
–10
O
NT
Input Return Loss RLin (dB)
0
–30
–15
–20
–25
–30
1 000 1 500 2 000 2 500 3 000 3 500 4 000
0
500
DI
SC
Frequency f (MHz)
0
25
–10
Isolation ISL (dB)
Power Gain GP (dB)
30
20
15
10
500
Frequency f (MHz)
–20
–30
–40
–50
5
0
1 000 1 500 2 000 2 500 3 000 3 500 4 000
ISOLATION vs. FREQUENCY
POWER GAIN vs. FREQUENCY
0
STOP 4 100.000 MHz
1 000 1 500 2 000 2 500 3 000 3 500 4 000
–60
0
500
1 000 1 500 2 000 2 500 3 000 3 500 4 000
Frequency f (MHz)
Frequency f (MHz)
Remark The graphs indicate nominal characteristics.
Data Sheet PU10672EJ01V0DS
7
µPC8232T5N
PACKAGE DIMENSIONS
DI
SC
O
NT
IN
U
ED
6-PIN PLASTIC TSON (UNIT: mm)
8
Data Sheet PU10672EJ01V0DS
µPC8232T5N
NOTES ON CORRECT USE
(1) Observe precautions for handling because of electro-static sensitive devices.
(2) Form a ground pattern as widely as possible to minimize ground impedance (to prevent undesired oscillation).
All the ground terminals must be connected together with wide ground pattern to decrease impedance
difference.
(4) Do not supply DC voltage to INPUT pin.
RECOMMENDED SOLDERING CONDITIONS
ED
(3) The bypass capacitor should be attached to VCC line.
This product should be soldered and mounted under the following recommended conditions.
For soldering
methods and conditions other than those recommended below, contact your nearby sales office.
Infrared Reflow
Wave Soldering
Soldering Conditions
Condition Symbol
IN
U
Soldering Method
Peak temperature (package surface temperature)
: 260°C or below
Time at peak temperature
: 10 seconds or less
Time at temperature of 220°C or higher
: 60 seconds or less
Preheating time at 120 to 180°C
: 120±30 seconds
Maximum number of reflow processes
Maximum chlorine content of rosin flux (% mass)
: 3 times
: 0.2%(Wt.) or below
Peak temperature (molten solder temperature)
: 260°C or below
Time at peak temperature
: 10 seconds or less
IR260
WS260
Preheating temperature (package surface temperature) : 120°C or below
Partial Heating
O
NT
Maximum number of flow processes
Maximum chlorine content of rosin flux (% mass)
: 1 time
: 0.2%(Wt.) or below
Peak temperature (terminal temperature)
: 350°C or below
Soldering time (per side of device)
Maximum chlorine content of rosin flux (% mass)
: 3 seconds or less
: 0.2%(Wt.) or below
HS350
DI
SC
Caution Do not use different soldering methods together (except for partial heating).
Data Sheet PU10672EJ01V0DS
9
ED
µPC8232T5N
DI
SC
O
NT
IN
U
• The information in this document is current as of July, 2007. The information is subject to change
without notice. For actual design-in, refer to the latest publications of NEC Electronics data sheets or
data books, etc., for the most up-to-date specifications of NEC Electronics products. Not all
products and/or types are available in every country. Please check with an NEC Electronics sales
representative for availability and additional information.
• No part of this document may be copied or reproduced in any form or by any means without the prior
written consent of NEC Electronics. NEC Electronics assumes no responsibility for any errors that may
appear in this document.
• NEC Electronics does not assume any liability for infringement of patents, copyrights or other intellectual
property rights of third parties by or arising from the use of NEC Electronics products listed in this document
or any other liability arising from the use of such products. No license, express, implied or otherwise, is
granted under any patents, copyrights or other intellectual property rights of NEC Electronics or others.
• Descriptions of circuits, software and other related information in this document are provided for illustrative
purposes in semiconductor product operation and application examples. The incorporation of these
circuits, software and information in the design of a customer's equipment shall be done under the full
responsibility of the customer. NEC Electronics assumes no responsibility for any losses incurred by
customers or third parties arising from the use of these circuits, software and information.
• While NEC Electronics endeavors to enhance the quality, reliability and safety of NEC Electronics products,
customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To
minimize risks of damage to property or injury (including death) to persons arising from defects in NEC
Electronics products, customers must incorporate sufficient safety measures in their design, such as
redundancy, fire-containment and anti-failure features.
• NEC Electronics products are classified into the following three quality grades: "Standard", "Special" and
"Specific".
The "Specific" quality grade applies only to NEC Electronics products developed based on a customerdesignated "quality assurance program" for a specific application. The recommended applications of an NEC
Electronics product depend on its quality grade, as indicated below. Customers must check the quality grade of
each NEC Electronics product before using it in a particular application.
"Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio
and visual equipment, home electronic appliances, machine tools, personal electronic equipment
and industrial robots.
"Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster
systems, anti-crime systems, safety equipment and medical equipment (not specifically designed
for life support).
"Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life
support systems and medical equipment for life support, etc.
The quality grade of NEC Electronics products is "Standard" unless otherwise expressly specified in NEC
Electronics data sheets or data books, etc. If customers wish to use NEC Electronics products in applications
not intended by NEC Electronics, they must contact an NEC Electronics sales representative in advance to
determine NEC Electronics' willingness to support a given application.
(Note)
(1) "NEC Electronics" as used in this statement means NEC Electronics Corporation and also includes its
majority-owned subsidiaries.
(2) "NEC Electronics products" means any product developed or manufactured by or for NEC Electronics (as
defined above).
M8E 02. 11-1
D
4590 Patrick Henry Drive
Santa Clara, CA 95054-1817
Telephone: (408) 919-2500
Facsimile: (408) 988-0279
UE
Subject: Compliance with EU Directives
CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant
with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous
Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive
2003/11/EC Restriction on Penta and Octa BDE.
IN
CEL Pb-free products have the same base part number with a suffix added. The suffix –A indicates
that the device is Pb-free. The –AZ suffix is used to designate devices containing Pb which are
exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals.
All devices with these suffixes meet the requirements of the RoHS directive.
This status is based on CEL’s understanding of the EU Directives and knowledge of the materials that
go into its products as of the date of disclosure of this information.
Lead (Pb)
Mercury
< 1000 PPM
Concentration contained
in CEL devices
-A
Not Detected
< 1000 PPM
Not Detected
< 100 PPM
Not Detected
SC
O
Cadmium
Concentration Limit per RoHS
(values are not yet fixed)
NT
Restricted Substance
per RoHS
Hexavalent Chromium
< 1000 PPM
Not Detected
PBB
< 1000 PPM
Not Detected
PBDE
< 1000 PPM
Not Detected
-AZ
(*)
If you should have any additional questions regarding our devices and compliance to environmental
standards, please do not hesitate to contact your local representative.
DI
Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance
content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information
provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better
integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate
information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL
suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for
release.
In no event shall CEL’s liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to
customer on an annual basis.
See CEL Terms and Conditions for additional clarification of warranties and liability.