REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add device type 02. Inactivate device type 01 (no approved source of supply). Add device types 03 through 07. Add vendors CAGE 32116, 5Y243, 57363, and 88379. Changed to reflect MIL-H-38534 processing. Editorial changes throughout. Add device type 08. Add vendor CAGE 8K957. Editorial changes throughout. Corrections to table I and figure 3. Editorial changes throughout. Changes in accordance with NOR 5962-R189-92. Redrawn with changes. Add case outlines U and Z. Add device type 09. Editorial changes throughout. Changes in accordance with NOR 5962-R110-94. Changes in accordance with NOR 5962-R013-96. Not used. Not used. Incorporated NOR's 5962-R110-94 and 5962-R013-96. Made changes to table I for device type 07. Redraw entire document. Inactivate device types 03, 04, and 07 for new design. Add device type 10. Rewrite paragraphs 4.2.a.2. and 4.3.3.b.2 to add TC. Table I, Total current, ICC1-SB, ICC1-25, ICC1-50, ICC1-100 for device type 05; change the maximum limit from 25 mA to 60 mA. (4 places) -gz Add case outline T. Correct paragraphs 4.2.a.2. and 4.3.3.b.2. -gz 88-09-20 M. A. Frye 89-12-04 W. Heckman 91-01-16 W. Heckman 92-03-03 92-04-27 92-11-11 Alan Barone Gregory A. Lude K. A. Cottongim 94-02-17 95-12-15 Kendall A. Cottongim Kendall A. Cottongim 96-06-20 K. A. Cottongim 98-01-28 K. A. Cottongim 04-11-05 07-05-10 Raymond Monnin Robert M. Heber 10-11-08 Charles F. Saffle B C D E F G H J K L M N P R THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV R R R R R R R R R R SHEET 15 16 17 18 19 20 21 22 23 24 REV STATUS REV R R R R R R R R R R R R R R OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Donald R. Osborne STANDARD MICROCIRCUIT DRAWING CHECKED BY D. A. Di Cenzo THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE APPROVED BY N. A. Hauck AMSC N/A DRAWING APPROVAL DATE 87-08-06 REVISION LEVEL R DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http://www.dscc.dla.mil MICROCIRCUIT, HYBRID, DIGITAL, DUAL CHANNEL, 15 VOLT, DRIVER-RECEIVER, RECEIVER IDLE NORMALLY LOW SIZE A SHEET DSCC FORM 2233 APR 97 CAGE CODE 5962-87579 67268 1 OF 24 5962-E377-10 1. SCOPE 1.1 Scope. This drawing describes device requirements for class H hybrid microcircuits to be processed in accordance with MIL-PRF-38534 and a choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). 1.2 PIN. The PIN shall be as shown in the following example: 5962-87579 Drawing number 01 Device type (see 1.2.1) X Case outline (see 1.2.2) X Lead finish (see 1.2.3) 1.2.1 Device types. The device types shall identify the circuit function as follows: Device type Generic number Circuit function 1/ 01 02 03 04 05 06 BUS-63125, BUS-63126 BUS-63123, BUS-63125II, BUS-63126II ARX2411 ARX3411 NHI-1500 FC 1553623 Dual channel driver-receiver Low power, dual channel driver-receiver Dual channel driver-receiver Low power, dual channel driver-receiver Low power, dual channel driver-receiver Low power, dual channel driver-receiver with thermal protection Low power, dual channel driver-receiver Low power, dual channel driver-receiver Low power, dual channel driver-receiver Low power, dual channel driver-receiver 2/ 3/ 3/ 4/ 07 3/ 08 09 10 CT-1487-D MR63125M FC 1553621 ACT-4487-D 1.2.2 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator T U X Y Z See figure 1 See figure 1 See figure 1 See figure 1 See figure 1 Terminals Package style 36 28 36 36 28 Flat package Dual-in-line Dual-in-line Flat package Flat package 1.2.3 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1/ 2/ 3/ 4/ Interfaces with Manchester encoder-decoder described in Standard Microcircuit Drawing 78029. Inactive for new design as of revision A, dated 88 SEP 20. Device types 03, 04, and 07 are inactive for new design. Device type 10 replaces device types 03, 04, and 07. For device type 06 only, the thermal protection operation is as follows: With the thermal override pins 4 and 13 disconnected transmission amplitude decreases as case temperature exceeds approximately 175C and is restored as case temperatures decreases. With pins 4 and 13 connected to 0 volts this feature is effectively disabled. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87579 A REVISION LEVEL R SHEET 2 1.3 Absolute maximum ratings. 1/ Supply voltage range: VCC (devices 01, 03, 04, 05, 07, 08, and 10) .......................... VEE (devices 01-04, 06, 07, 08, 09, and 10) ........................... VCC1 (all devices) .................................................................... Logic input voltage ..................................................................... Receiver differential voltage ...................................................... Receiver common mode voltage range ..................................... Driver peak output current ......................................................... Power dissipation (PD) at TC = +125C: (devices 01 and 08) ................................................................ (device 02) ............................................................................. (device 03) ............................................................................. (devices 04 and 10) ................................................................ (device 05) ............................................................................. (devices 06 and 09 ................................................................. (device 07) ............................................................................. Storage temperature range........................................................ Lead temperature (soldering, 10 seconds) ................................ Junction temperature (TJ): (devices 01-04, 06, 07, 08, 09, and 10) ................................. (device 05) ............................................................................. Thermal resistance, junction-to-case (JC): (devices 01 and 05) ................................................................ (devices 02, 08, and 10) ......................................................... (device 03) ............................................................................. (device 04) ............................................................................. (devices 06 and 09) ................................................................ (device 07) ............................................................................. Thermal resistance, junction-to-ambient (JA): (devices 01 and 05) ................................................................ (devices 02, 08, and 10) ......................................................... (device 03) ............................................................................. (device 04) ............................................................................. (devices 06 and 09) ................................................................ (device 07) ............................................................................. -0.3 V dc to +18 V dc +0.3 V dc to -18 V dc -0.3 V dc to +7 V dc -0.3 V dc to VCC1 40 VP-P -10 V dc to +10 V dc 200 mA 4W 3W 3.3 W 2/ 2W 2/ 0.96 W 2/ 1.65 W 2/ 3W -65C to +150C +300C +160C +150C 8.8C/W 7.0C/W 47.2C/W 88C/W 18C/W 60C/W 28.8C/W 27.0C/W 67.2C/W 108C/W 35C/W 80C/W 1.4 Recommended operating conditions. Supply voltage range: VCC (devices 01, 03, 04, 05, 07, and 10) ................................ VCC (device 08) ....................................................................... VEE (devices 01-04, 06, 07, 09, and 10) ................................. VEE (device 08) ....................................................................... VCC1 (all devices) .................................................................... Logic input voltage ..................................................................... Receiver differential voltage: (devices 01, 02, 03, 06, and 09) ............................................. (devices 04, 05, 07, 08, and 10) ............................................. Receiver common mode voltage range: (devices 01, 02, 03, 04, 06, and 09) ....................................... (devices 05, 07, 08, and 10) ................................................... Driver peak output current (all devices) ..................................... Serial data rate .......................................................................... Junction temperature (TJ): (devices 01, 02, 03, 05, 06, 08, 09, and 10 ............................ (devices 04 and 07) ................................................................ Case operating temperature range (TC) .................................... +14.25 V dc to +15.75 V dc +11.25 V dc to +15.75 V dc -14.25 V dc to -15.75 V dc -11.25 V dc to -15.75 V dc +4.5 V dc to +5.5 V dc 0 V dc to +5 V dc 30 VP-P 40 VP-P -5 V dc to +5 V dc -10 V dc to +10 V dc 180 mA 1.0 MHz maximum +150C +160C -55C to +125C 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade the performance and affect reliability. 2/ One channel transmitting at 100 percent duty cycle and the second channel is at standby. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87579 A REVISION LEVEL R SHEET 3 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. MIL-HDBK-1553 - Multiplex Applications Handbook. (Copies of these documents are available online at https://assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device class H shall be in accordance with MILPRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as designated in the device manufacturer's Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Timing waveforms. The timing waveforms shall be as specified on figure 3. 3.2.4 Typical bus connections. The typical bus connections shall be as specified on figure 4. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87579 A REVISION LEVEL R SHEET 4 3.5 Marking of devices. Marking of devices shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime-VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime-VA shall affirm that the manufacturer's product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. 4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. b. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DLA Land and Maritime-VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA or TC as specified in accordance with table I of method 1015 of MIL-STD-883. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87579 A REVISION LEVEL R SHEET 5 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TC +125C unless otherwise specified Group A subgroups Device types Limits Min Unit Max RECEIVER Input level VI Differential input, pin 15 to pin 16 2/ 4,5,6 All Input common mode voltage range VICM Independent of xfmr or in accordance with MILHDBK-1553 section 5.1.2.2 2/ 3/ 4,5,6 01,02,03,04, 06,09 05,07,08,10 IOL = 16 mA 1,2,3 Output low voltage Output high voltage VOL 40 VP-P -5 +5 mV(pk) -10 +10 01,02 0.5 IOL = 4 mA 03,04,07,08, 10 0.5 IOL = 8 mA 05,06,09 0.5 VOH IOH = -0.4 mA 1,2,3 All Input low voltage VIL 4/ 1,2,3 All Input high voltage VIH 4/ 1,2,3 All Input low current IIL VIL = 0.4 V 1,2,3 V 2.5 V TRANSMITTER V 01,06,09 -1.6 mA 02 -0.72 03 -3.2 04,05,08,10 -0.4 07 -1.0 IIH VIH = 2.7 V 1,2,3 All Output voltage VO Across 35 load 5/ 1,2,3 01,02,05,06, 08,09 03,04,07,10 VON Across 35 load 5/ 4,5,6 V 2 Input high current Output noise voltage 0.7 All 0.04 mA 6 9 VP-P 6.5 9 10 mVP-P See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87579 A REVISION LEVEL R SHEET 6 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TC +125C unless otherwise specified Group A subgroups Device types Limits Min Unit Max RECEIVER STROBE Input low voltage VSIL 4/ 1,2,3 01-03, 05-09,10 0.7 04 0.40 Input high voltage VSIH 4/ 1,2,3 All 2 Input low current ISIL VSIL = 0.4 V 1,2,3 01,06,09 -1.6 02,05 -0.72 03 -0.8 04,08,10 -0.4 07 -1.0 Input high current V V mA ISIH VSIH = 2.7 V 1,2,3 All 0.04 mA Input low voltage VIIL 4/ 1,2,3 All 0.7 V Input high voltage VIIH 4/ 1,2,3 All 2 Input low current IIIL VSIL = 0.4 V 1,2,3 01,03,06,09 -1.6 02 -0.72 04,05,08,10 -0.4 07 -1.0 TRANSMITTER INHIBIT Input high current IIIH VSIH = 2.7 V 1,2,3 All mA 0.04 mA See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87579 A REVISION LEVEL R SHEET 7 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TC +125C unless otherwise specified Group A subgroups Device types Limits Min Unit Max POWER SUPPLY Total current ICC-SB 1,2,3 01 03,08 04,10 05 07 55 32 1 25 44 IEE-SB 1,2,3 01,08 06,09 02 03 04,10 07 55 30 35 26 16.5 70 ICC1-SB 1,2,3 01,06,09 02 03 04,10 05 07 08 35 45 20 30 60 90 25 4,5,6 01,04,08,10 03 05 07 55 90 69 100 IEE-25 4,5,6 01,06,08,09 02 2/ 03 04,10 07 100 80 26 21 70 ICC1-25 4,5,6 01 02 2/ 06,09 03 04,10 05 07 08 4,5,6 01,08 03 04,10 05 07 55 140 110 118 155 4,5,6 01 08 02,06,09 03 04,10 07 145 150 130 26 25 70 ICC-25 ICC-50 (standby mode) (25% duty cycle into 35 load) (50% duty cycle into 35 load) IEE-50 mA 35 45 45 20 30 60 90 25 See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87579 A REVISION LEVEL R SHEET 8 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TC +125C unless otherwise specified Group A subgroups Device types Limits Min Unit Max POWER SUPPLY - Continued. Total current ICC1-50 (50% duty cycle into 35 load) 4,5,6 01 02,06,09 03 04,10 05 07 08 35 45 20 30 60 90 25 ICC-100 (100% duty cycle into 35 load) 1,2,3 01,08 03 04 05,10 07 55 240 220 209 260 IEE-100 1,2,3 01 02 2/ 06,08,09 03 04,10 07 255 255 255 26 30 70 ICC1-100 1,2,3 01 4/ 02 2/ 03,08 04,10 05 06,09 07 35 45 20 30 60 55 90 4,5,6 01-09 mA RECEIVER Input resistance RIN 1 MHz sine wave 2/ 6/ 7/ 8/ Input capacitance Threshold voltage CIN VTH VTH 10 1 MHz sine wave 2/ TC = +25C 7 k (See figure 4) 4 01-09 6/ 7/ 8/ 4,5,6 10 5/ 9/ 1,2,3 08,10 0.56 1.1 01-05 0.56 1.0 06,09 0.6 1.2 07 0.86 1.1 All 0.50 1.1 Group C end-point electricals 9/ 1,2,3 5 pF (See figure 4) VP-P VP-P See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87579 A REVISION LEVEL R SHEET 9 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TC +125C unless otherwise specified Group A subgroups Device types Limits Min Unit Max TRANSMITTER Output resistance (transmitter off) ROUT 1 MHz sine wave 2/ 4,5,6 6/ 7/ 8/ Output capacitance (transmitter off) COUT 01-09 10 10 1 MHz sine wave 2/ TC = +25C 4 01-09 6/ 7/ 8/ 4,5,6 10 k (See figure 4) 5 pF (See figure 4) Output offset voltage VOS 2/ 10/ 4,5,6 All -90 +90 mV(pk) Peak amplitude variation AV 11/ 4,5,6 All -15 +15 % Delay time, input to output tDR Delay time from differential input zero crossing to DATA or DATA. 2/ (See figure 3) 9,10,11 All 400 ns Strobe delay tDS Delay time from strobe rising or falling edge to DATA or DATA. 2/ (See figure 3) 9,10,11 01-03,05-10 200 04 250 RECEIVER TRANSMITTER Rise time tR Output load = 35 (See figure 3) 9,10,11 All 100 300 ns Fall time tF Output load = 35 (See figure 3) 9,10,11 All 100 300 ns Delay time tDT (See figure 3) 2/ 9,10,11 01-03, 05,06,09 250 ns 04,08 350 07,10 200 01-09 450 10 200 Inhibit delay inhibiting tDI-H (See figure 3) 2/ 9,10,11 ns See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87579 A REVISION LEVEL R SHEET 10 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TC +125C unless otherwise specified Group A subgroups Limits Device types Min Unit Max TRANSMITTER - Continued. Inhibit delay active tDT-L (See figure 3) 2/ 9,10,11 01-05,08 250 06,09 300 07,10 150 ns TRANSMITTER / RECEIVER Input impedance Zoi In accordance with MILHDBK-1553, section 100, appendix A, test plan 5.1.2.3. (See figure 4) Transformer coupled stubs 4,5,6 10 2/ 3/ 4/ 5/ 6/ 7/ 8/ 9/ 10/ 11/ k 2.0 Direct coupled stubs 1/ 1.0 VCC = 15 V dc, VEE = -15 V dc, and VCC1 = +5 V dc. All specifications and limits are for a single channel with no connections made to the other channel. This parameter is tested initially and after any process or design change which might affect this parameter. Common mode rejection for device type 10 is as shown on figure 4. These parameters are tested on a go-no-go basis in conjunction with other measured parameters and are not directly testable. See figure 4 for device type 10. Not measured directly, but as part of input impedance (ZIN). Test in accordance with MIL-HDBK-1553, section 100, appendix A, test plan 5.1.2.3. See figure 4. This parameter is 100 percent tested for device type 10. See input impedance test (Zoi) and figure 4. Threshold is measured in direct coupled mode including the transformer. Threshold is the maximum level on the BUS at which there are no pulses on either receiver output. Divide by 1.4 to obtain threshold in transformer coupled mode. Add 0.14 V in direct coupled mode or 0.10 V in transformer coupled mode to obtain threshold at which no errors are observed when receiver is used with 15530 CMOS Manchester encoder-decoder. Measured across 35 load, 2.5 µs after parity bit mid-bit zero crossing of a 660 µs message. Measured across 35 load, variation of average peak amplitude. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87579 A REVISION LEVEL R SHEET 11 Case outline T. FIGURE 1. Case outlines. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87579 A REVISION LEVEL R SHEET 12 Case outline T - Continued. Symbol Millimeters Min A Inches Max Min Max 3.30 .130 A1 1.75 2.01 .069 .079 b 0.356 0.457 .014 .018 c 0.152 0.254 .006 .010 D 26.04 D1 21.46 21.72 1.025 .845 .855 E 17.55 .691 E1 18.16 .715 E2 36.58 38.86 1.440 1.530 e 1.14 1.40 .045 .055 F 4.83 5.33 .190 .210 J 0.635 0.889 .025 .035 L 9.65 10.67 .380 .420 NOTES: 1. The U.S. government preferred system of measurement is the metric SI. This item was designed using inchpound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Pin numbers are for reference only 3. Package material is alumina (AL2O3). FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87579 A REVISION LEVEL R SHEET 13 Case outline U. Inches .002 .005 .010 .018 .060 .100 .210 .250 .600 .770 1.470 mm 0.05 0.13 0.25 0.46 1.52 2.54 5.33 6.35 15.24 19.56 37.34 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Lead identification numbers are for reference only. 4. Lead spacing dimensions apply only at seating plane. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87579 A REVISION LEVEL R SHEET 14 Case outline X. Inches .005 .01 .015 .018 .055 .086 .09 .10 .100 .600 .775 1.700 1.895 mm 0.13 0.3 0.38 0.46 1.40 2.18 2.3 2.5 2.54 15.24 19.68 43.18 48.13 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Lead identification numbers are for reference only. 4. Lead spacing dimensions apply only at seating plane. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87579 A REVISION LEVEL R SHEET 15 Case outline Y. Inches .002 .010 .015 .100 .165 .250 .785 1.700 1.905 mm 0.05 0.25 0.38 2.54 4.19 6.35 19.94 43.18 48.39 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Lead identification numbers are for reference only. 4. Lead spacing dimensions apply only at seating plane. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87579 A REVISION LEVEL R SHEET 16 Case outline Z. Inches .002 .003 .010 .015 .035 .065 .097 .100 .180 .40 .78 1.50 mm 0.05 0.08 0.25 0.38 0.89 1.65 2.46 2.54 4.51 10.16 19.81 38.10 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Lead identification numbers are for reference only. 4. Lead spacing dimensions apply only at seating plane. FIGURE 1. Case outlines - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87579 A REVISION LEVEL R SHEET 17 Case outline T. Pin Function 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 TX data out TX data out GND NC RX data out Strobe GND RX data out DNC TX data out TX data out GND NC RX data out Strobe GND RX data out NC NC RX data in RX data in GND VEE VCC1 Inhibit TX data in TX data in NC RX data in RX data in GND VEE VCC1 Inhibit TX data in TX data in Channel One One One One One One One Two Two Two Two Two Two Two Two Two Two Two Two Two Two Two One One One One One One One One NOTES: 1. GND pins should all be connected externally. 2. NC = no internal connection. 3. DNC = do not connect. FIGURE 2. Terminal connections. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87579 A REVISION LEVEL R SHEET 18 Case outlines X and Y. Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 Function TX data out TX data out GND NC RX data out Strobe GND RX data out GND or Case TX data out TX data out GND NC RX data out Strobe GND RX data out NC VCC or NC RX data in RX data in GND VEE VCC1 Inhibit TX data in TX data in VCC or NC RX data in RX data in GND VEE VCC1 Inhibit TX data in TX data in Channel One One One One One One One One Two Two Two Two Two Two Two Two Two Two Two Two Two Two Two Two One One One One One One One One One NOTES: 1. GND pins should all be connected externally. 2. Device types 01, 03, 04, 05, 07, and 10; pins 19 and 28 are +15 V dc. Device types 02, 06, and 09; pins 19 and 28 are not connected (NC). 3. Device type 06; pins 4 and 13 are available for the thermal protection 4. Device types 06 and 09; pins 3,12, 22, and 31 are not connected (NC). FIGURE 2. Terminal connections - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87579 A REVISION LEVEL R SHEET 19 Case outlines U and Z. Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Function Channel TX data out/RX data in TX data out/RX data in GND RX strobe RX data out RX data out Case TX data out/RX data in TX data out/RX data in GND RX strobe RX data out RX data out No connection GND VEE VCC1 TX inhibit TX data in TX data in VCC GND VEE VCC1 Inhibit TX data in TX data in VCC One One One One One One Two Two Two Two Two Two Two Two Two Two Two Two Two One One One One One One One NOTE: 1. GND pins should all be connected externally. FIGURE 2. Terminal connections - Continued. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87579 A REVISION LEVEL R SHEET 20 Receiver timing Transmitter timing FIGURE 3. Timing waveforms. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87579 A REVISION LEVEL R SHEET 21 NOTE: 1. Transformer is a Technitrol, part number 1553-2 or equivalent. FIGURE 4. Typical bus connections. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87579 A REVISION LEVEL R SHEET 22 TABLE II. Electrical test requirements. MIL-PRF-38534 test requirements Subgroups (in accordance with MIL-PRF-38534, group A test table) ---- Interim electrical parameters Final electrical parameters 1*, 2, 3, 4, 5, 6, 9, 10, 11 Group A test requirements 1, 2, 3, 4, 5, 6, 9, 10, 11 1, 2, 3 Group C end-point electrical parameters * PDA applies to subgroup 1. 4.3 Conformance and periodic inspections. Conformance inspection (CI) and periodic inspection (PI) shall be in accordance with MIL-PRF-38534 and as specified herein. 4.3.1 Group A inspection (CI). Group A inspection shall be in accordance with MIL-PRF-38534 and as follows: a. Tests shall be as specified in table II herein. b. Subgroups 7 and 8 shall be omitted. 4.3.2 Group B inspection (PI). Group B inspection shall be in accordance with MIL-PRF-38534. 4.3.3 Group C inspection (PI). Group C inspection shall be in accordance with MIL-PRF-38534 and as follows: a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test, method 1005 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DLA Land and Maritime-VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-883. (2) TA or TC as specified in accordance with table I of method 1005 of MIL-STD-883. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. 4.3.4 Group D inspection (PI). Group D inspection shall be in accordance with MIL-PRF-38534. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87579 A REVISION LEVEL R SHEET 23 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38534. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractorprepared specification or drawing. 6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated as specified in MIL-PRF38534. 6.4 Record of users. Military and industrial users shall inform DLA Land and Maritime when a system application requires configuration control and the applicable SMD. DLA Land and Maritime will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices (FSC 5962) should contact DLA Land and Maritime-VA, telephone (614) 692-0547. 6.5 Comments. Comments on this drawing should be directed to DLA Land and Maritime-VA, Columbus, Ohio 43218-3990, or telephone (614) 692-1081. 6.6 Sources of supply. Sources of supply are listed in MIL-HDBK-103 and QML-38534. The vendors listed in MIL-HDBK103 and QML-38534 have submitted a certificate of compliance (see 3.7 herein) to DLA Land and Maritime-VA and have agreed to this drawing. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87579 A REVISION LEVEL R SHEET 24 STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 10-11-08 Approved sources of supply for SMD 5962-87579 are listed below for immediate acquisition information only and shall be added to MIL-HDBK-103 and QML-38534 during the next revisions. MIL-HDBK-103 and QML-38534 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DLA Land and Maritime-VA. This information bulletin is superseded by the next dated revisions of MIL-HDBK-103 and QML-38534. DLA Land and Maritime maintains an online database of all current sources of supply at http://www.dscc.dla.mil/Programs/Smcr/. 1/ 2/ 3/ 4/ Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-8757901XA 5962-8757901YA 3/ 3/ BUS-63125 BUS-63125 5962-8757902TC 5962-8757902XA 5962-8757902XC 5962-8757902YA 5962-8757902YC 19645 19645 19645 19645 19645 BUS-63123-600 BUS-63125II-140 BUS-63125II-110 BUS-63126II-140 BUS-63126II-110 5962-8757903XA 5962-8757903YA 4/ 4/ ARX2411 ARX2411FP 5962-8757904UA 5962-8757904XA 5962-8757904YA 5962-8757904ZA 4/ 4/ 4/ 4/ ARX3411 ARX3411 ARX3411FP ARX3411FP 5962-8757905XA 5962-8757905XC 5962-8757905YA 5962-8757905YC 57363 57363 57363 57363 NHI-1500/883 NHI-1500/883 NHI-1500FP/883 NHI-1500FP/883 5962-8757906XA 5962-8757906XC 5962-8757906YA 5962-8757906YC U4388 U4388 U4388 U4388 FC 1553623 FC 1553623 FC 1553623 FP FC 1553623 FP 5962-8757907XX 5962-8757907YX 4/ 4/ CT1487-D CT1487-DFP The lead finish shown for each PIN, representing a hermetic package, is the most readily available from the manufacturer listed for that part. If the desired lead finish is not listed contact the Vendor to determine availability. Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. Not available from an approved source. Not available from an approved source. Device type 10 replaces device types 03, 04, and 07. 1 of 2 STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued. DATE: 10-11-08 1/ 2/ 3/ 4/ Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-8757908XX 3/ MR63125M 5962-8757909XA 5962-8757909XC 5962-8757909YA 5962-8757909YC U4388 U4388 U4388 U4388 FC 1553621 FC 1553621 FC 1553621 FP FC 1553621 FP 5962-8757910XA 5962-8757910XC 5962-8757910YA 5962-8757910YC 88379 88379 88379 88379 ACT4487-D ACT4487-D ACT4487-DF ACT4487-DF The lead finish shown for each PIN, representing a hermetic package, is the most readily available from the manufacturer listed for that part. If the desired lead finish is not listed contact the Vendor to determine availability. Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. Not available from an approved source. Not available from an approved source. Device type 10 replaces device types 03, 04, and 07. Vendor CAGE number Vendor name and address U4388 C-MAC Microcircuits, Ltd South Denes Great Yarmouth Norfolk NR30 3PX England 19645 Data Device Corporation 105 Wilbur Place Bohemia, NY 11716-2482 57363 National Hybrid, Incorporated 2200 Smithtown Avenue Ronkonkoma, NY 11779-7329 88379 Aeroflex Plainview, Incorporated 35 South Service Road Plainview, NY 11803-4101 The information contained herein is disseminated for convenience only and the Government assumes no liability whatsoever for any inaccuracies in the information bulletin. 2 of 2