MOTOROLA SEMICONDUCTOR TECHNICAL DATA JK FlipĆFlop MC10EL35 MC100EL35 The MC10EL/100EL35 is a high speed JK flip-flop. The J/K data enters the master portion of the flip-flop when the clock is LOW and is transferred to the slave, and thus the outputs, upon a positive transition of the clock. The reset pin is asynchronous and is activated with a logic HIGH. • • • • • 525ps Propagation Delay 2.2GHz Toggle Frequency High Bandwidth Output Transitions 75kΩ Internal Input Pulldown Resistors 8 >1000V ESD Protection 1 D SUFFIX PLASTIC SOIC PACKAGE CASE 751-05 LOGIC DIAGRAM AND PINOUT ASSIGNMENT J 1 J 8 VCC K 2 K 7 Q CLK 3 6 Q TRUTH TABLE R R 4 5 VEE J K R CLK Qn+1 L L H H X L H L H X L L L L H Z Z Z Z X Qn L H Qn L Z = LOW to HIGH Transition 12/93 Motorola, Inc. 1996 3–1 REV 2 MC10EL35 MC100EL35 DC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = GND) –40°C Symbol Characteristic Min 0°C Typ Max IEE Power Supply Current 10EL 100EL 27 27 32 32 VEE Power Supply Voltage 10EL 100EL –5.2 –4.5 IIH Input HIGH Current Min –4.75 –4.20 25°C Typ Max 27 27 32 32 –5.2 –4.5 –5.5 –5.5 150 Min –4.75 –4.20 85°C Typ Max 27 27 32 32 –5.2 –4.5 –5.5 –5.5 150 Min –4.75 –4.20 Typ Max Unit 27 32 32 37 mA –5.2 –4.5 –5.5 –5.5 V 150 µA 150 AC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = GND) –40°C Symbol Characteristic Min Typ 1.4 2.0 CLK MR 290 225 515 450 Setup Time J, K 150 tH Hold Time J, K tRR Reset Recovery tPW Minimum Pulse Width CLK, Reset 400 tr tf Output Rise/Fall Times Q (20% – 80%) 100 fMAX Maximum Toggle Frequency tPLH tPHL Propagation Delay to Output tS MOTOROLA 0°C Max Min Typ 1.8 2.2 340 275 515 450 0 150 250 100 400 200 740 675 25°C Max Min Typ 1.8 2.2 350 275 525 450 0 150 250 100 400 200 690 625 400 225 350 100 85°C Max Min Typ 1.8 2.2 395 350 570 525 0 150 0 ps 250 100 250 100 ps 400 200 400 200 ps 700 625 400 225 3–2 350 100 Max 745 700 400 225 350 100 Unit GHz ps ps 225 350 ps ECLinPS and ECLinPS Lite DL140 — Rev 3 MC10EL35 MC100EL35 OUTLINE DIMENSIONS D SUFFIX PLASTIC SOIC PACKAGE CASE 751–05 ISSUE P –A– M 1 4 R 0.25 (0.010) 4X –B– X 45 _ B M 5 P 8 NOTES: 1. DIMENSIONS A AND B ARE DATUMS AND T IS A DATUM SURFACE. 2. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 3. DIMENSIONS ARE IN MILLIMETER. 4. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 5. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 6. DIMENSION D DOES NOT INCLUDE MOLD PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. J M_ C F G –T– K SEATING PLANE 8X D 0.25 (0.010) M T B S A S DIM A B C D F G J K M P R MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.18 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454 JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315 MFAX: [email protected] – TOUCHTONE 602–244–6609 INTERNET: http://Design–NET.com ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 ◊ ECLinPS and ECLinPS Lite DL140 — Rev 3 3–3 *MC10EL35/D* MC10EL35/D MOTOROLA