ISL9N306AD3 / ISL9N306AD3ST
N-Channel Logic Level PWM Optimized UltraFET® Trench Power MOSFETs
30V, 50A, 6mΩ
General Description
Features
This device employs a new advanced trench MOSFET
technology and features low gate charge while maintaining
low on-resistance.
• Fast switching
Optimized for switching applications, this device improves
the overall efficiency of DC/DC converters and allows
operation to higher switching frequencies.
• rDS(ON) = 0.0085Ω (Typ), V GS = 4.5V
Applications
• Qgd (Typ) = 11nC
• DC/DC converters
• CISS (Typ) = 3400pF
• rDS(ON) = 0.0052Ω (Typ), V GS = 10V
• Qg (Typ) = 30nC, VGS = 5V
SOURCE
DRAIN
DRAIN (FLANGE)
DRAIN
(FLANGE)
D
GATE
GATE
G
SOURCE
S
TO-252
TO-251
MOSFET Maximum Ratings TA = 25°C unless otherwise noted
Symbol
VDSS
Drain to Source Voltage
Parameter
Ratings
30
Units
V
VGS
Gate to Source Voltage
±20
V
A
Drain Current
ID
Continuous (TC = 25oC, VGS = 10V)
50
Continuous (TC = 100oC, VGS = 4.5V)
50
A
Continuous (TC = 25oC, VGS = V, RθJC = 52oC/W)
16
A
Pulsed
PD
Power dissipation
Derate above 25oC
TJ, TSTG
Operating and Storage Temperature
Figure 4
A
125
0.83
W
W/oC
o
-55 to 175
C
Thermal Characteristics
RθJC
Thermal Resistance Junction to Case TO-251, TO-252
1.2
o
C/W
RθJA
Thermal Resistance Junction to Ambient TO-251, TO-252
100
o
C/W
RθJA
Thermal Resistance Junction to Ambient TO-252, 1in2 copper pad area
52
o
C/W
Package Marking and Ordering Information
Device Marking
N306AD
Device
ISL9N306AD3ST
Package
TO-252AA
Reel Size
330mm
Tape Width
16mm
Quantity
2500 units
N306AD
ISL9N306AD3
TO-251AA
Tube
N/A
75 units
©2003 Fairchild Semiconductor Corporation
ISL9N306AD3 / ISL9N306AD3ST Rev. B2
ISL9N306AD3 / ISL9N306AD3ST
June 2003
Symbol
Parameter
Test Conditions
Min
Typ
Max
Units
Off Characteristics
BVDSS
Drain to Source Breakdown Voltage
IDSS
Zero Gate Voltage Drain Current
IGSS
Gate to Source Leakage Current
ID = 250µA, VGS = 0V
VDS = 25V
VGS = 0V
TC = 150o
VGS = ±20V
30
-
-
V
-
-
1
-
-
250
µA
-
-
±100
nA
3
V
On Characteristics
VGS(TH)
rDS(ON)
Gate to Source Threshold Voltage
Drain to Source On Resistance
VGS = VDS, ID = 250µA
1
ID = 50A, VGS = 10V
-
0.0052 0.0060
-
ID = 50A, VGS = 4.5V
-
0.0085 0.0095
Ω
Dynamic Characteristics
CISS
Input Capacitance
COSS
Output Capacitance
CRSS
Reverse Transfer Capacitance
VDS = 15V, VGS = 0V,
f = 1MHz
-
3400
-
-
650
-
pF
pF
-
300
-
pF
nC
Qg(TOT)
Total Gate Charge at 10V
VGS = 0V to 10V
-
60
90
Qg(5)
Total Gate Charge at 5V
-
30
45
nC
Qg(TH)
Threshold Gate Charge
-
3.0
4.5
nC
Qgs
Gate to Source Gate Charge
VGS = 0V to 5V V = 15V
DD
VGS = 0V to 1V ID = 50A
Ig = 1.0mA
-
10
-
nC
Qgd
Gate to Drain “Miller” Charge
-
11
-
nC
ns
Switching Characteristics (VGS = 4.5V)
tON
Turn-On Time
-
-
131
td(ON)
Turn-On Delay Time
-
16
-
ns
tr
Rise Time
-
70
-
ns
td(OFF)
Turn-Off Delay Time
-
34
-
ns
tf
Fall Time
-
30
-
ns
tOFF
Turn-Off Time
-
-
97
ns
ns
VDD = 15V, ID = 16A
VGS = 4.5V, RGS = 4.3Ω
Switching Characteristics (VGS = 10V)
tON
Turn-On Time
-
-
80
td(ON)
Turn-On Delay Time
-
10
-
ns
tr
Rise Time
-
43
-
ns
td(OFF)
Turn-Off Delay Time
-
62
-
ns
tf
Fall Time
-
29
-
ns
tOFF
Turn-Off Time
-
-
137
ns
428
-
-
µs
V
VDD = 15V, ID = 16A
VGS = 10V, R GS = 4.3Ω
Unclamped Inductive Switching
tAV
Avalanche Time
ID = 30A, L = 200µH
Drain-Source Diode Characteristics
ISD = 50A
-
-
1.25
ISD = 25A
-
-
1.0
V
Reverse Recovery Time
ISD = 50A, dISD /dt = 100A/µs
-
-
35
ns
Reverse Recovered Charge
ISD = 50A, dISD /dt = 100A/µs
-
-
30
nC
VSD
Source to Drain Diode Voltage
trr
QRR
©2003 Fairchild Semiconductor Corporation
ISL9N306AD3 / ISL9N306AD3ST Rev. B2
ISL9N306AD3 / ISL9N306AD3ST
Electrical Characteristics TA = 25°C unless otherwise noted
60
1.0
50
ID, DRAIN CURRENT (A)
POWER DISSIPATION MULTIPLIER
1.2
0.8
0.6
0.4
0.2
VGS = 10V
40
VGS = 4.5V
30
20
10
0
0
0
25
50
75
100
150
125
25
175
50
75
TC , CASE TEMPERATURE (oC)
100
125
150
175
TC, CASE TEMPERATURE (oC)
Figure 1. Normalized Power Dissipation vs
Ambient Temperature
Figure 2. Maximum Continuous Drain Current vs
Case Temperature
2
DUTY CYCLE - DESCENDING ORDER
0.5
0.2
0.1
0.05
0.02
0.01
ZθJC, NORMALIZED
THERMAL IMPEDANCE
1
PDM
0.1
t1
t2
SINGLE PULSE
0.01
10-5
10-4
10-3
NOTES:
DUTY FACTOR: D = t1/t2
PEAK TJ = PDM x ZθJC x RθJC + TC
10-2
10-1
100
101
t, RECTANGULAR PULSE DURATION (s)
Figure 3. Normalized Maximum transient Thermal Impedance
IDM , PEAK CURRENT (A)
2000
TC = 25oC
FOR TEMPERATURES
ABOVE 25oC DERATE PEAK
CURRENT AS FOLLOWS:
1000
175 – TC
150
I = I25
VGS = 10V
VGS = 5V
100
40
TRANSCONDUCTANCE
MAY LIMIT CURRENT
IN THIS REGION
10 -5
10-4
10-3
10-2
10-1
100
101
t, PULSE WIDTH (s)
Figure 4. Peak Current Capability
©2003 Fairchild Semiconductor Corporation
ISL9N306AD3 / ISL9N306AD3ST Rev. B2
ISL9N306AD3 / ISL9N306AD3ST
Typical Characteristic
100
100
50
TJ = 175oC
25
TJ = 25oC
TJ =
VGS = 3.5V
75
50
VGS = 3V
25
TC = 25 oC
-55oC
PULSE DURATION = 80µs
DUTY CYCLE = 0.5% MAX
0
0
1
2
3
4
0
5
0.5
VGS, GATE TO SOURCE VOLTAGE (V)
1.0
1.5
2.0
VDS , DRAIN TO SOURCE VOLTAGE (V)
Figure 5. Transfer Characteristics
Figure 6. Saturation Characteristics
2.0
25
PULSE DURATION = 80µs
DUTY CYCLE = 0.5% MAX
TC = 25oC
ID = 25A
NORMALIZED DRAIN TO SOURCE
ON RESISTANCE
rDS(ON), DRAIN TO SOURCE
ON RESISTANCE (mΩ)
VGS = 4.5V
VGS = 10V
75
ID, DRAIN CURRENT (A)
ID , DRAIN CURRENT (A)
PULSE DURATION = 80µs
DUTY CYCLE = 0.5% MAX
VDD = 15V
20
15
ID = 50A
ID =5A
10
PULSE DURATION = 80µs
DUTY CYCLE = 0.5% MAX
1.5
1.0
VGS = 10V, ID = 50A
0.5
5
2
4
6
8
-80
10
-40
0
40
80
120
Figure 7. Drain to Source On Resistance vs Gate
Voltage and Drain Current
200
Figure 8. Normalized Drain to Source On
Resistance vs Junction Temperature
1.4
1.2
ID = 250µA
NORMALIZED DRAIN TO SOURCE
BREAKDOWN VOLTAGE
VGS = VDS, ID = 250µA
NORMALIZED GATE
THRESHOLD VOLTAGE
160
TJ, JUNCTION TEMPERATURE (oC)
VGS, GATE TO SOURCE VOLTAGE (V)
1.0
0.6
0.2
1.1
1.0
0.9
-80
-40
0
40
80
120
160
200
TJ, JUNCTION TEMPERATURE (oC)
Figure 9. Normalized Gate Threshold Voltage vs
Junction Temperature
©2003 Fairchild Semiconductor Corporation
-80
-40
0
40
80
120
160
200
TJ , JUNCTION TEMPERATURE (oC)
Figure 10. Normalized Drain to Source
Breakdown Voltage vs Junction Temperature
ISL9N306AD3 / ISL9N306AD3ST Rev. B2
ISL9N306AD3 / ISL9N306AD3ST
Typical Characteristic (Continued)
5000
10
VDD = 15V
VGS , GATE TO SOURCE VOLTAGE (V)
C, CAPACITANCE (pF)
CISS = CGS + C GD
COSS ≅ CDS + C GD
1000
CRSS = CGD
VGS = 0V, f = 1MHz
100
0.1
6
4
WAVEFORMS IN
DESCENDING ORDER:
ID = 50A
ID = 25A
ID = 5A
2
0
0
30
1
10
VDS , DRAIN TO SOURCE VOLTAGE (V)
8
10
Figure 11. Capacitance vs Drain to Source
Voltage
30
40
50
60
Figure 12. Gate Charge Waveforms for Constant
Gate Currents
300
500
VGS = 4.5V, VDD = 15V, ID = 16A
VGS = 10V, VDD = 15V, I D = 16A
250
400
SWITCHING TIME (ns)
SWITCHING TIME (ns)
20
Qg, GATE CHARGE (nC)
200
tf
tr
150
100
td(OFF)
300
td(OFF)
200
tf
100
50
tr
td(ON)
0
td(ON)
0
0
10
20
30
40
50
0
RGS, GATE TO SOURCE RESISTANCE (Ω)
10
20
30
40
50
RGS, GATE TO SOURCE RESISTANCE (Ω)
Figure 13. Switching Time vs Gate Resistance
Figure 14. Switching Time vs Gate Resistance
Test Circuits and Waveforms
BVDSS
VDS
tP
VDS
L
IAS
VDD
VARY tP TO OBTAIN
REQUIRED PEAK IAS
+
RG
VDD
-
VGS
DUT
tP
0V
IAS
0
0.01Ω
tAV
Figure 15. Unclamped Energy Test Circuit
©2003 Fairchild Semiconductor Corporation
Figure 16. Unclamped Energy Waveforms
ISL9N306AD3 / ISL9N306AD3ST Rev. B2
ISL9N306AD3 / ISL9N306AD3ST
Typical Characteristic (Continued)
VDS
VDD
RL
Qg(TOT)
VDS
VGS = 10V
VGS
Qg(5)
+
VDD
VGS = 5V
VGS
-
VGS = 1V
DUT
0
Ig(REF)
Qg(TH)
Qgs
Qgd
Ig(REF)
0
Figure 17. Gate Charge Test Circuit
Figure 18. Gate Charge Waveforms
VDS
tON
tOFF
td(ON)
td(OFF)
tr
RL
VDS
tf
90%
90%
+
VGS
VDD
-
10%
0
10%
DUT
90%
RGS
VGS
VGS
0
Figure 19. Switching Time Test Circuit
©2003 Fairchild Semiconductor Corporation
50%
10%
50%
PULSE WIDTH
Figure 20. Switching Time Waveforms
ISL9N306AD3 / ISL9N306AD3ST Rev. B2
ISL9N306AD3 / ISL9N306AD3ST
Test Circuits and Waveforms (Continued)
(T
–T )
JM
A
P D M = ----------------------------Z θJ A
125
RθJA = 33.32 + 23.84/(0.268+Area)
100
RθJA (oC/W)
The maximum rated junction temperature, TJM , and the
thermal resistance of the heat dissipating path determines
the maximum allowable device power dissipation, PDM , in an
application.
Therefore the application’s ambient
temperature, TA (oC), and thermal resistance RθJA (oC/W)
must be reviewed to ensure that TJM is never exceeded.
Equation 1 mathematically represents the relationship and
serves as the basis for establishing the rating of the part.
75
(EQ. 1)
50
In using surface mount devices such as the TO-252
package, the environment in which it is applied will have a
significant influence on the part’s current and maximum
power dissipation ratings. Precise determination of P DM is
complex and influenced by many factors:
1. Mounting pad area onto which the device is attached and
whether there is copper on one side or both sides of the
board.
25
0.01
0.1
1
10
AREA, TOP COPPER AREA (in2)
Figure 21. Thermal Resistance vs Mounting
Pad Area
2. The number of copper layers and the thickness of the
board.
3. The use of external heat sinks.
4. The use of thermal vias.
5. Air flow and board orientation.
6. For non steady state applications, the pulse width, the
duty cycle and the transient thermal response of the part,
the board and the environment they are in.
Fairchild provides thermal information to assist the
designer’s preliminary application evaluation. Figure 21
defines the RθJA for the device as a function of the top
copper (component side) area. This is for a horizontally
positioned FR-4 board with 1oz copper after 1000 seconds
of steady state power with no air flow. This graph provides
the necessary information for calculation of the steady state
junction temperature or power dissipation. Pulse
applications can be evaluated using the Fairchild device
Spice thermal model or manually utilizing the normalized
maximum transient thermal impedance curve.
Displayed on the curve are RθJA values listed in the
Electrical Specifications table. The points were chosen to
depict the compromise between the copper board area, the
thermal resistance and ultimately the power dissipation,
PDM .
Thermal resistances corresponding to other copper areas
can be obtained from Figure 21 or by calculation using
Equation 2. R θJA is defined as the natural log of the area
times a coefficient added to a constant. The area, in square
inches is the top copper area including the gate and source
pads.
23.84
( 0.268 + Area )
Rθ JA = 33.32 + -------------------------------------
©2003 Fairchild Semiconductor Corporation
(EQ. 2)
ISL9N306AD3 / ISL9N306AD3ST Rev. B2
ISL9N306AD3 / ISL9N306AD3ST
Thermal Resistance vs. Mounting Pad Area
.SUBCKT ISL9N306A 2 1 3 ;
rev May 2001
CA 12 8 2.0e-9
CB 15 14 2.3e-9
CIN 6 8 3e-9
LDRAIN
DBODY 7 5 DBODYMOD
DBREAK 5 11 DBREAKMOD
DPLCAP 10 5 DPLCAPMOD
DPLCAP
10
5
51
EVTHRES
+ 19 8
+
LGATE
GATE
1
EVTEMP
RGATE +
18 22
9
20
21
11
+
17
EBREAK 18
-
16
DBODY
MWEAK
6
MMED
MSTRO
RLGATE
LSOURCE
CIN
MMED 16 6 8 8 MMEDMOD
MSTRO 16 6 8 8 MSTROMOD
MWEAK 16 21 8 8 MWEAKMOD
RBREAK 17 18 RBREAKMOD 1
RDRAIN 50 16 RDRAINMOD 1e-3
RGATE 9 20 2.69
RLDRAIN 2 5 10
RLGATE 1 9 45.8
RLSOURCE 3 7 14.7
RSLC1 5 51 RSLCMOD 1e-6
RSLC2 5 50 1e3
RSOURCE 8 7 RSOURCEMOD 3.5e-3
RVTHRES 22 8 RVTHRESMOD 1
RVTEMP 18 19 RVTEMPMOD 1
ESLC
50
RDRAIN
6
8
ESG
DBREAK
+
RSLC2
IT 8 17 1
S1A
S1B
S2A
S2B
RLDRAIN
RSLC1
51
EBREAK 11 7 17 18 35.8
EDS 14 8 5 8 1
EGS 13 8 6 8 1
ESG 6 10 6 8 1
EVTHRES 6 21 19 8 1
EVTEMP 20 6 18 22 1
LDRAIN 2 5 1.0e-9
LGATE 1 9 4.58e-9
LSOURCE 3 7 1.47e-9
DRAIN
2
5
8
SOURCE
3
7
RSOURCE
RLSOURCE
S1A
12
S2A
13
8
S1B
CA
RBREAK
15
14
13
17
18
RVTEMP
S2B
13
CB
6
8
EGS
5
8
EDS
-
19
VBAT
+
IT
14
+
+
-
8
22
RVTHRES
6 12 13 8 S1AMOD
13 12 13 8 S1BMOD
6 15 14 13 S2AMOD
13 15 14 13 S2BMOD
VBAT 22 19 DC 1
ESLC 51 50 VALUE={(V(5,51)/ABS(V(5,51)))*(PWR(V(5,51)/(1e-6*275),5))}
.MODEL DBODYMOD D (IS = 3.6e-11 N=1.075 RS = 3.5e-3 TRS1 = 1e-3 TRS2 = 1e-6 XTI=1.0 CJO = 1.45e-9 TT = 8e-11 M =
0.51)
.MODEL DBREAKMOD D (RS = 1.7e-1 TRS1 = 1e-3 TRS2 = -8.9e-6)
.MODEL DPLCAPMOD D (CJO = 11.5e-10 IS = 1e-30 N = 10 M = 0.46)
.MODEL MMEDMOD NMOS (VTO = 1.7 KP = 9 IS=1e-30 N = 10 TOX = 1 L = 1u W = 1u RG = 2.69)
.MODEL MSTROMOD NMOS (VTO = 2.1 KP = 100 IS = 1e-30 N= 10 TOX = 1 L = 1u W = 1u)
.MODEL MWEAKMOD NMOS (VTO = 1.36 KP = 0.05 IS = 1e-30 N = 10 TOX = 1 L = 1u W = 1u RG = 26.9 RS = 0.1)
.MODEL RBREAKMOD RES (TC1 = 1e-3 TC2 = -7e-7)
.MODEL RDRAINMOD RES (TC1 = 1.2e-2 TC2 = 3.0e-5)
.MODEL RSLCMOD RES (TC1 = 1e-3 TC2 = 1e-6)
.MODEL RSOURCEMOD RES (TC1 = 1e-3 TC2 = 1e-6)
.MODEL RVTHRESMOD RES (TC1 = -2.6e-3 TC2 = -7.5e-6)
.MODEL RVTEMPMOD RES (TC1 = -1.8e-3 TC2 = 1e-6)
.MODEL S1AMOD VSWITCH (RON = 1e-5
.MODEL S1BMOD VSWITCH (RON = 1e-5
.MODEL S2AMOD VSWITCH (RON = 1e-5
.MODEL S2BMOD VSWITCH (RON = 1e-5
ROFF = 0.1
ROFF = 0.1
ROFF = 0.1
ROFF = 0.1
VON = -4.0 VOFF= -0.8)
VON = -0.8 VOFF= -4.0)
VON = -0.3 VOFF= 0.2)
VON = 0.2 VOFF= -0.3)
.ENDS
NOTE: For further discussion of the PSPICE model, consult A New PSPICE Sub-Circuit for the Power MOSFET Featuring Global
Temperature Options; IEEE Power Electronics Specialist Conference Records, 1991, written by William J. Hepp and C. Frank
Wheatley.
©2003 Fairchild Semiconductor Corporation
ISL9N306AD3 / ISL9N306AD3ST Rev. B2
ISL9N306AD3 / ISL9N306AD3ST
PSPICE Electrical Model
REV May 2001
template ISL9N306A n2,n1,n3
electrical n2,n1,n3
{
var i iscl
dp..model dbodymod = (isl = 3.6e-11, nl=1.075 , rs = 3.5e-3, trs1 = 1e-3, trs2 = 1e-6, xti=1.0, cjo = 1.45e-9, tt = 8e-11, m = 0.51,)
dp..model dbreakmod = (rs =0.17, trs1 = 1e-3, trs2 = -8.9e-6)
dp..model dplcapmod = (cjo = 11.5e-10, isl=10e-30, nl=10, m=0.46)
m..model mmedmod = (type=_n, vto = 1.7, kp=9, is=1e-30, tox=1)
m..model mstrongmod = (type=_n, vto = 2.1, kp = 100, is = 1e-30, tox = 1)
m..model mweakmod = (type=_n, vto = 1.36, kp = 0.05, is = 1e-30, tox = 1, rs=0.1)
sw_vcsp..model s1amod = (ron = 1e-5, roff = 0.1, von = -4.0, voff = -0.8)
sw_vcsp..model s1bmod = (ron =1e-5, roff = 0.1, von = -0.8, voff = -4.0)
sw_vcsp..model s2amod = (ron = 1e-5, roff = 0.1, von = -0.3, voff = 0.2)
LDRAIN
sw_vcsp..model s2bmod = (ron = 1e-5, roff = 0.1, von = 0.2, voff = -0.3) DPLCAP 5
DRAIN
RLDRAIN
RSLC1
51
RSLC2
ISCL
dp.dbody n7 n5 = model=dbodymod
dp.dbreak n5 n11 = model=dbreakmod
dp.dplcap n10 n5 = model=dplcapmod
RDRAIN
6
8
ESG
LGATE
11
DBODY
EVTHRES
16
21
+ 19 8
+
GATE
1
DBREAK
50
-
i.it n8 n17 = 1
l.ldrain n2 n5 = 1e-9
l.lgate n1 n9 = 4.58e-9
l.lsource n3 n7 = 1.47e-9
2
10
c.ca n12 n8 = 2.0e-9
c.cb n15 n14 = 2.3e-9
c.cin n6 n8 = 3e-9
EVTEMP
RGATE +
18 22
9
20
6
MWEAK
EBREAK
+
MMED
MSTRO
RLGATE
m.mmed n16 n6 n8 n8 = model=mmedmod, l=1u, w=1u
m.mstrong n16 n6 n8 n8 = model=mstrongmod, l=1u, w=1u
m.mweak n16 n21 n8 n8 = model=mweakmod, l=1u, w=1u
CIN
17
18
-
8
LSOURCE
SOURCE
3
7
RSOURCE
RLSOURCE
res.rbreak n17 n18 = 1, tc1 = 1e-3, tc2 = -7e-7
res.rdrain n50 n16 = 1e-3, tc1 = 1.2e-2, tc2 = 3.0e-5
res.rgate n9 n20 = 2.69
res.rldrain n2 n5 = 10
res.rlgate n1 n9 = 45.8
res.rlsource n3 n7 = 14.7
res.rslc1 n5 n51= 1e-6, tc1 = 1e-3, tc2 =1e-6
res.rslc2 n5 n50 = 1e3
res.rsource n8 n7 = 3.5e-3, tc1 = 1e-3, tc2 =1e-6
res.rvtemp n18 n19 = 1, tc1 = -1.8e-3, tc2 = 1e-6
res.rvthres n22 n8 = 1, tc1 = -2.6e-3, tc2 = -7.5e-6
S1A
12
13
8
S2A
S1B
CA
RBREAK
15
14
13
17
18
RVTEMP
S2B
13
CB
6
8
EGS
-
19
IT
14
+
+
VBAT
5
8
EDS
-
+
8
22
RVTHRES
spe.ebreak n11 n7 n17 n18 = 35.8
spe.eds n14 n8 n5 n8 = 1
spe.egs n13 n8 n6 n8 = 1
spe.esg n6 n10 n6 n8 = 1
spe.evtemp n20 n6 n18 n22 = 1
spe.evthres n6 n21 n19 n8 = 1
sw_vcsp.s1a n6 n12 n13 n8 = model=s1amod
sw_vcsp.s1b n13 n12 n13 n8 = model=s1bmod
sw_vcsp.s2a n6 n15 n14 n13 = model=s2amod
sw_vcsp.s2b n13 n15 n14 n13 = model=s2bmod
v.vbat n22 n19 = dc=1
equations {
i (n51->n50) +=iscl
iscl: v(n51,n50) = ((v(n5,n51)/(1e-9+abs(v(n5,n51))))*((abs(v(n5,n51)*1e-6/275))** 5))
}
}
©2003 Fairchild Semiconductor Corporation
ISL9N306AD3 / ISL9N306AD3ST Rev. B2
ISL9N306AD3 / ISL9N306AD3ST
SABER Electrical Model
th
JUNCTION
REV May 2001
ISL9N306AT
CTHERM1 th 6 2.7e-4
CTHERM2 6 5 3.9e-3
CTHERM3 5 4 4.2e-3
CTHERM4 4 3 4.8e-3
CTHERM5 3 2 1.9e-2
CTHERM6 2 tl 5.9e-2
RTHERM1 th 6 1.0e-3
RTHERM2 6 5 4.8e-3
RTHERM3 5 4 4.5e-2
RTHERM4 4 3 2.6e-1
RTHERM5 3 2 3.1e-1
RTHERM6 2 tl 3.4e-1
SABER Thermal Model
RTHERM1
CTHERM1
6
RTHERM2
CTHERM2
5
CTHERM3
RTHERM3
SABER thermal model ISL9N306AT
template thermal_model th tl
thermal_c th, tl
{
ctherm.ctherm1 th 6 = 2.7e-4
ctherm.ctherm2 6 5 = 3.9e-3
ctherm.ctherm3 5 4 = 4.2e-3
ctherm.ctherm4 4 3 = 4.8e-3
ctherm.ctherm5 3 2 = 1.9e-2
ctherm.ctherm6 2 tl = 5.9e-2
4
RTHERM4
CTHERM4
3
rtherm.rtherm1 th 6 = 1.0e-3
rtherm.rtherm2 6 5 = 4.8e-3
rtherm.rtherm3 5 4 = 4.5e-2
rtherm.rtherm4 4 3 = 2.6e-1
rtherm.rtherm5 3 2 = 3.1e-1
rtherm.rtherm6 2 tl = 3.4e-1
}
RTHERM5
CTHERM5
2
RTHERM6
CTHERM6
tl
©2003 Fairchild Semiconductor Corporation
CASE
ISL9N306AD3 / ISL9N306AD3ST Rev. B2
ISL9N306AD3 / ISL9N306AD3ST
SPICE Thermal Model
TRADEMARKS
The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not
intended to be an exhaustive list of all such trademarks.
ACEx™
FACT™
ActiveArray™
FACT Quiet Series™
Bottomless™
FAST®
CoolFET™
FASTr™
CROSSVOLT™ FRFET™
DOME™
GlobalOptoisolator™
EcoSPARK™
GTO™
E2CMOS™
HiSeC™
I2C™
EnSigna™
Across the board. Around the world.™
The Power Franchise™
Programmable Active Droop™
ImpliedDisconnect™
ISOPLANAR™
LittleFET™
MicroFET™
MicroPak™
MICROWIRE™
MSX™
MSXPro™
OCX™
OCXPro™
OPTOLOGIC®
OPTOPLANAR™
PACMAN™
POP™
Power247™
PowerTrench®
QFET™
QS™
QT Optoelectronics™
Quiet Series™
RapidConfigure™
RapidConnect™
SILENT SWITCHER®
SMART START™
SPM™
Stealth™
SuperSOT™-3
SuperSOT™-6
SuperSOT™-8
SyncFET™
TinyLogic®
TruTranslation™
UHC™
UltraFET®
VCX™
DISCLAIMER
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY
PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY
LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN;
NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR
CORPORATION.
As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body,
or (b) support or sustain life, or (c) whose failure to perform
when properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to
result in significant injury to the user.
2. A critical component is any component of a life support
device or system whose failure to perform can be
reasonably expected to cause the failure of the life support
device or system, or to affect its safety or effectiveness.
PRODUCT STATUS DEFINITIONS
Definition of Terms
Datasheet Identification
Product Status
Definition
Advance Information
Formative or In
Design
This datasheet contains the design specifications for
product development. Specifications may change in
any manner without notice.
Preliminary
First Production
This datasheet contains preliminary data, and
supplementary data will be published at a later date.
Fairchild Semiconductor reserves the right to make
changes at any time without notice in order to improve
design.
No Identification Needed
Full Production
This datasheet contains final specifications. Fairchild
Semiconductor reserves the right to make changes at
any time without notice in order to improve design.
Obsolete
Not In Production
This datasheet contains specifications on a product
that has been discontinued by Fairchild semiconductor.
The datasheet is printed for reference information only.
Rev. I2